Transcription
ADT CarbonMonoxide AlarmSetup Guide
A1.SetupTake the ADT Carbon Monoxide Alarm to where youintend to mount it after setup. Make sure you are within 350 feet from theADT Security Hub. (Exact range depends onyour home’s construction, the environment, theposition of the ADT Security Hub, and the positionand number of other connected devices.) Make sure that your ADT Security Hub is disarmedbefore connecting a new device. Make sure that you only setup one new deviceat a time.2. Use the SmartThings app on your smartphone toselect the “My Home” tab. Select "Things", and then“Add a Thing".Setup3. Remove the tab on the carbon monoxide alarmmarked “Pull This Tab”. Do not remove the tab until you are ready tosetup the detector.Carbon Monoxide Alarm (Back)Battery Tab
BSetup4. Use the SmartThings app to scan the QR code onthe front of the alarm and then follow the on-screeninstructions to complete setup.Carbon Monoxide Alarm (Front)QR Code5. Remove the QR code from the front of the alarm andattach it inside the ADT Security Hub User Guide forfuture reference.PlacementInstall the ADT Carbon Monoxide Alarm in a place wherethe alarm can be heard easily. Ideally, a carbon monoxidealarm should be installed in: Every room containing a fuel burning appliance. Within 10 feet of a sleeping area. On every floor of the building.WARNING: This product is intended for use in ordinaryindoor locations of family living units. It is not designedto measure compliance with Occupational Safety andHealth Administration (OSHA) commercial or industrialstandards.
PlacementPlacementCarbon monoxide alarm suggested Locations:Do not place the ADT Carbon Monoxide Alarm in anyof the following areas: In the immediate vicinity of a cooking appliance(keep it at least 5 feet away from it). Outside the building. In an enclosed space, e. g. in or below a cupboard. In a damp or humid area. Directly above a sink or cooker. Next to a door, window, air vent, or anywhere it couldbe affected by drafts. Next to an extractor fan.HallwayAtticBedroomKitchenBasementMaster BedroomFamily RoomGarage
Placement Over heat sources such as radiators or hot air vents. Where it would be obstructed, e.g. by curtains orfurniture. In an area where the temperature could be below-50 F or above 104 F. Where it could be easily knocked or damaged, oraccidentally turned off or removed. Near paint, thinners, solvent fumes, or air fresheners. Where dirt or dust could block the detector. In a bathroom or other areas where it may be exposedto water splashes, dripping or condensation, e.g.above an electric kettle.PlacementIf locating the ADT Carbon Monoxide Alarm in a roomwith a fuel burning appliance: If mounted on a wall, it should be located at aheight greater than the height of any door or windowbut still be at least 5.9 inches from the ceiling. If mounted on the ceiling, it should be at least12 inches from any wall or light fitting. The alarm should be a horizontal distance ofbetween 3.28 and 9.84 feet from the potentialcarbon monoxide source. In rooms with sloped ceilings, the alarm should belocated on the high side of the room.
Placement If there is a partition in the room, the alarm shouldbe located on the same side of the partition as thepotential source.If locating the ADT Carbon Monoxide Alarm in a bedroomor in rooms remote from a fuel burning appliance: Mount the alarm within 10 feet of the occupants. Always make sure it is possible to view the threelight indicators when in the vicinity of the alarm.PlacementCarbon Monoxide Alarm Ceiling Placement:Not This Area4 Inches (10cm)Anywhere In This Area3 Feet(0.9m)3 Feet(0.9m)Carbon Monoxide Alarms should face out in this position:Wall Behind AlarmCarbon Monoxide Alarm (Front)
C1.MountingMountingInstall the mounting base using the two screwsand anchors provided.Ceiling12 inchesfrom wall2. Fit the alarm inside the base by aligning it over thebase, then turn the alarm in a clockwise directionuntil it clicks into place. The three LEDs will flashwhile the alarm powers up.12 inchesfrom wallALARMFAULTPOWERMounting BaseCarbon Monoxide Alarm (Front)CARBONMONOXIDEALARM3. Test the alarm after completing the installation.
DTestingTest the ADT Carbon Monoxide Alarm weekly by pressingand holding the test button for a few seconds while theADT Security Hub is in Walk Test Mode. See the ADTSecurity Hub User Guide for more details.Replace the alarm when the “Replace unit by” date hasbeen reached (check label on the side of the device).Note: If you have an ADT professional monitoring serviceactivated, additional testing is required when you connectnew devices. Follow the on-screen instructions in theSmartThings app to complete testing.Important: This carbon monoxide alarm must be testedand maintained weekly. This device is designed to protectindividuals from the acute effects of carbon monoxideexposure. It will not fully safeguard individuals withspecific medical conditions. If in doubt, consult a medicalTestingpractitioner. Individuals with medical problems mayconsider using warning devices which provide audibleand visual signals for carbon monoxide concentrationsunder 30 ppm.
ETroubleshootingIf the alarm does not sound when you press the testbutton:1.Make sure the batteries are properly inserted andthen wait 15 seconds.2. Hold button down firmly for at least 5 seconds.3. Check the alarm is secured correctly on the mountingplate.4. Replace batteries.FUseWhen the ADT Carbon Monoxide Alarm detects potentiallydangerous levels of carbon monoxide, it flashes the redlight immediately and then sounds a loud alarm if thecarbon monoxide persists.Alarm - Red LEDFault - Amber LEDPower - Green LEDThe below table shows how the alarm reacts todifferent levels of carbon monoxide gas and exposuretime. At higher levels of carbon monoxide, the alarmturns on sooner.
UseUseThe rate of flashing of the red light indicates the levelof carbon monoxide. If your alarm sounds, follow theinstructions in the “What To Do” column.The following symptoms are related to CARBONMONOXIDE POISONING and are to be discussed withALL members of the household:Caution: The alarm only indicates the presence of carbonmonoxide gas in the area where the ADT Carbon MonoxideAlarm is located. Carbon monoxide gas may be present inother areas. Mild Exposure: Slight headache, nausea, vomiting,fatigue (often described as flu-like symptoms). Medium Exposure: Severe throbbing headache,drowsiness, confusion, fast heart rate. Extreme Exposure: Unconsciousness, convulsions,cardiorespiratory failure, death.This carbon monoxide alarm is designed to detect carbonmonoxide gas from ANY source of combustion. It is notdesigned to detect smoke, fire or any other gas.WARNING: Actuation of your carbon monoxide alarmindicates the presence of carbon monoxide (CO) which canKILL YOU.Many cases of reported CARBON MONOXIDE POISONINGindicate that while victims are aware they are not well,they become so disoriented they are unable to savethemselves by either exiting the building or calling forassistance. Young children and household pets aretypically the first affected.
AlarmsUseWhat You Hear / SeeWhat It MeansWhat To DoNo beeping, red LEDblinking once every 3 seconds.Low levels of carbon monoxidedetected.Open a window or door to get fresh air.Siren beeping, red LEDblinking once every 3 seconds.Low levels of carbon monoxidedetected for 60 minutes.Open a window or door to get fresh air. Press the Hush button to mutethe alarm.No beeping, red LEDblinking twice every 3 seconds.Moderate levels of carbonmonoxide detected.Open a window or door to get fresh air. Investigate the source of thecarbon monoxide.Siren beeping, red LEDblinking twice every 3 seconds.Moderate levels of carbonmonoxide detected for 10 minutes.Open a window or door to get fresh air. Investigate the source of thecarbon monoxide.Siren beeping, red LEDblinking three times every 3seconds.Critical levels of carbonmonoxide detected for 2 minutes.1. Immediately move to fresh air.2. Call your fire department or 911.3. DO NOT re-enter the premises until the emergency servicesresponders have arrived, the premises have been aired out andyour alarm remains in its normal condition.
MaintenanceUseWhat You Hear / SeeWhat It MeansWhat To DoNo beeping.Normal operation.No action.1 Beep every minute.Amber LED flash once every48 seconds, green LED off.Low batteries.Replace batteries.2 Beeps every minute.Amber LED flash twice every48 seconds, green LED off.Carbon monoxide alarmerror.Replace unit with same brand.3 Beeps every minute.Amber LED flash three timesevery 48 seconds, green LED off.Product expired(10 years from the date ofmanufacture indicated on thealarm).Replace unit with same brand.
GSuggestionsThe ADT Carbon Monoxide Alarm monitors for carbonmonoxide in your home. When carbon monoxide isdetected, the alarm sounds and a notification is sentto your ADT Security Hub.Your ADT Security Hub can then send an alert to yoursmartphone, automate connected devices, or initiateoptional ADT professional monitoring services(additional fees apply).SuggestionsThere are many ways you can use an ADT CarbonMonoxide Alarm in your home: Put one in a room containing a fuel-burningappliance and set it to initiate optional ADTprofessional monitoring services when carbonmonoxide is detected in your home (additionalfees apply). Put one in your bedroom and set it to turn onconnected lights when carbon monoxide is detected. Put one in your hallway and set it to turn off aconnected thermostat to avoid spreading carbonmonoxide through your home.
SuggestionsNote: To ensure proper functioning, all connected devicesmust be configured correctly. This alarm is not designedto be interconnected with other manufacturers' productsunless otherwise specified.Visit SmartThings.com/Welcome for more ideas, tips,and special offers.HWorks With SmartThingsSmartThings works with a wide range of connecteddevices, including lights, cameras, locks, thermostats,and sensors. It also works with the Google Assistantand Amazon Alexa so you can control your smart homewith voice commands.Look for the Works with SmartThings label next timeyou’re buying a connected device for your home, or visitSmartThings.com to see the full list of compatibledevices.
SmartThings, Inc., 665 Clyde Ave, Mountain View, CA 94043, USA. Information in this documentis subject to change without notice. Copyright 2017 SmartThings, Inc. All rights reserved.ADT and the ADT logo are marks and/or registered marks of ADT. Unauthorized use is strictlyprohibited. Revised 06/17.P/N 10015712.
The ADT Carbon Monoxide Alarm monitors for carbon monoxide in your home. When carbon monoxide is detected, the alarm sounds and a notification is sent to your ADT Security Hub. Your ADT Security Hub can then send an alert to your smartphone, automate connected devices, or initiate optional ADT
