WIXLIB

E-1600-SS-IP / E-1600-RD-IP / E-1600-YL-IP / E-1600-BL-IP / E-1600-BLP-IP / E-1600-BK-IPConnections: Gel-filled butt connectorsMounting: Surface mount to walls, posts or single gang electricalboxes. Attach the mounting plate in desired location and connectthe wires. Then, secure the phone to the mounting plate withprovided 8-32 set screws.Optional Enhanced Weather Protection (EWP) Available: EWPproducts are designed to meet IP66 standards and may feature foamrubber gaskets, sealed connections, gel-filled butt connectors, aswell as potted circuit boards with internally sealed, field-adjustabletrim pots and DIP switches for easy onsite programming. For moreinformation on EWP, see DOD 859.Note: For greater weather resistance, apply a bead of clear siliconcaulking around the top edge and sides of the chassis.Dimensions: 5.75” x 3.08” x 1.05” (146 mm x 78 mm x 27 mm)Shipping Weight: 2.5 lbs (1.3 kg)Material / Finish E-1600-SS-IP only: 0.060” thick (16 gauge)marine grade 316 stainless steel with a #4 brushed finishMaterial: 0.060” thick (16 gauge) 304 stainless steelFinish: E-1600-RD-IP: Red fine texture powder paintE-1600-YL-IP: Yellow fine texture powder paintE-1600-BL-IP: Blue fine texture powder paintE-1600-BLP-IP: Blue fine texture powder paint with“POLICE” verbiageE-1600-BK-IP: Black fine texture powder paint3.08BOTTOM VIEWEMERGENCYPHONEPOLICECondensationDrain Holes0.313Radius(model E-1600-BLP-IP only)SpeakerGrade 2 Braille Label5.75PUSH FORHELPSetScrewVIKING Push to Call button with redbacklit Call Connected LEDMicrophoneSIDE VIEW0.313 RadiusCALL CONNECTED WHEN LIT1.05FRONT VIEW2.922.520.20 x 0.43mounting slotUPMOUNTINGPLATEDIMENSIONSMount withthis arrowpointing up3.905.323.280.78 diameterwire exit hole0.63(4) 0.20 diametermounting holes0.30 diametercountersunkmounting hole6SetScrew

E-1600-02-IPDimensions: 13” x 10.5” x 2” (330mm x 267mm x 51mm)Shipping Weight: 7 lbs (3.18 kg)Connections: Gel-filled butt connectorsMaterial: 0.105” (12 gauge) brushed stainless steelMounting: Flush mount in elevator cabs, ATMs, stairwells,hallways, etc.Suggested Hardware: (6) #8 x 3/4 flat head phillips sheetmetal type A screws (not included)Optional Enhanced Weather Protection (EWP) Available:EWP products are designed to meet IP66 standards and mayfeature foam rubber gaskets, sealed connections, gel-filled buttconnectors, as well as potted circuit boards with internally sealed,field-adjustable trim pots and DIP switches for easy onsiteprogramming. For more information on EWP, see DOD 859.Note: When mounting outside to rough or uneven surfaces(brick, stucco, etc.) apply a bead of clear silicone caulkingaround the top edge and sides of faceplate.Note: When European CE compliance is required, mountonto a metal enclosure.10.50.250.2510.03.83.1Earth Ground theGreen/Yellowwire using theprovided wire CTED12.5PUSH FORGrade 2BrailleLabelRed CallConnectedLED4.7HELPEarthGroundVIKING Push ToCall Button2.0(6) 0.188 diametercountersunk holes(Side View)7

E-1600-03-IPDimensions: 7.22” x 5.36” x 1.55” (183mm x 149mm x 39mm)Material: 14 gauge vandal resistant Marine grade 316 brushedstainless steel panelShipping Weight: 3.0 lbs (1.36 kg)Connections: Gel-filled butt connectorsMounting: Surface mount to walls, posts, single gang boxes, doublegang boxes or 4” x 4” electrical junction boxes or recess mount inelevator phone boxes. Attach mounting plate in desired location.Attach wires then fasten cover to mounting plate with set screw.Optional Enhanced Weather Protection (EWP) Available:EWP products are designed to meet IP66 standards and mayfeature foam rubber gaskets, sealed connections, gel-filled buttconnectors, as well as potted circuit boards with internally sealed,field-adjustable trim pots and DIP switches for easy onsiteprogramming. For more information on EWP, see DOD 859.Note: For greater weather resistance, apply a bead of clear siliconcaulking around the top edge and sides of the chassis.(Front View)5.36EMERGENCYPHONELaser Etched GraphicsGrade 2 Braille LabelEarth Ground the Green/Yellowwire using the provided wire nutEarthGroundPUSH FORHELP7.22VIKING Marine grade 316stainless steel faceplateand push button switch(sealed per IP67)CALLCONNECTEDCall Connected LEDPush to Call buttonVIKING (2) 8-32 x .5" setscrews provided(Mounting Plate)(4) .22 diametermounting holes1.69CondensationDrain Hole0.781dia.1.703.403.306.781.55(Bottom View)0.7950.80(4) .187 x .50 slotsfor double gang box1.702.6053.405.00(2) .187 x .50 slotsfor single gang box8

E-1600-20-IPDimensions: Overall: 5.0” x 5.0” x 2.25” (127mm x 127 x 57mm),Plastic Electrical Box: 4.0” x 4.0” x 2.14” (102mm x 102mm x54mm)Optional Enhanced Weather Protection (EWP) Available: EWPproducts are designed to meet IP66 standards and may featurefoam rubber gaskets, sealed connections, gel-filled buttconnectors, as well as potted circuit boards with internally sealed,field-adjustable trim pots and DIP switches for easy onsiteprogramming. For more information on EWP, see DOD 859.Shipping Weight: 2.12 lbs (1.0 kg)Front Panel Material: 14 gauge Marine grade 316 brushedstainless steelNote: When mounting outside to rough or uneven surfaces (brick,stucco, etc.) apply a bead of clear silicone caulking around the topedge / sides of faceplate or VE-5x5.Connections: Gel-filled butt connectorsMounting with Plastic Rough-In Box (included): Flush into walls,mounts to side of wall stud.Mounting with Optional VE-5x5: Surface mount to walls, single gangboxes, double gang boxes, posts, or to a Viking VE-GNP Gooseneckpedestal, see DOD 424.Note: When European CE compliance is required, mount inoptional VE-5X5 metal enclosure.2.1”* Front View ofPlastic Rough-InBox (included)Peel paper liner and adhere gasketto back of panel, centering overmounting holes. Caution: For roughsurfaces (ie: brick, stucco, etc.)additional caulking may be required.4.0"Wall Stud** Wireknock out(4) T-10 Torx stainless steel,flat head, security screwsand drive bit (included)Laser Etched GraphicsPHELINFO(2) Standardflat head drywall (sheetrock) screws(not included) OR Earth Ground theGreen/Yellowwire using theprovided wire nutLCALCTEDNEMarine grade 316 stainlesssteel faceplate and push buttonswitches (sealed per IP67)C ONGrade 2 Braille Label"Help" Push to Call ButtonEarthGroundCall Connected Red LED"Info" Push to Call ButtonCondensation Drain Hole5.22”3.25”(4) 0.38” diameter(for gooseneckpedestal mounting)(2) 0.2 x 0.43 slots for single gang box(4) 0.2 x 0.43 slots for double gang boxCondensationDrain Hole5.14”3.0” 3.3”**(2) 0.74"diameter3.0”2.25”Front View of OptionalVE-5x5 (not included)Rear View of OptionalVE-5x5 (not included)Optional VE-5x5 Surface Mount Box with black satin powder paint finish, notincluded (DOD 424). Optional VE-LIGHT kit can be used to illuminate the faceplatewhen used with a VE-5x5 (DOD 428). WARNING: Do NOT use a wet location box.The optional VE-5x5 SurfaceMount Box (left) is designed to besurface mounted to a single gangbox, double gang box or VE-GNPGooseneck Pedestal. For moreinformation on the VE-5x5 andVE-GNP, see DOD 424.Important: The E-1600-20-IP willNOT mount to a standard doublegang box. If your applicationsrequires a double gang box, seemodel E-1600A-22-IP on page 10.* Note: The black plastic rough-in box (part # 259576) may be purchased separately (Example: Mounting boxes to studs before thewalls are finished for flush installation). Go to www.vikingelectronics.com and click on “Spare Parts” to order these rough-in boxes.** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To preventcondensation from accumulating inside the E-1600-20-IP always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4”diameter hole in the bottom of the black plastic box.9

E-1600-22-IPDimensions: 5.0” x 5.0” x 2.25” (127mm x 127 x 57mm)Mounting in a Double Gang Rough-In Box (not included):Flush into walls, mounts to side of wall studs, etc.Shipping Weight: 2.12 lbs (1.0 lbs)Note: For surface mount installations, use model E-1600-20-IPwith VE-5x5 surface mount box.Front Panel Material: 14 gauge marine grade 316 brushedstainless steelNote: When mounting outside to rough or uneven surfaces(brick, stucco, etc.) apply a bead of clear silicone caulkingaround the top edge and sides of faceplate.Connections: Gel-filled butt connectorsInfo Button: Dials up to 5 non-emergency phone numbersNote: When European CE compliance is required, mount asshown, in a metal enclosure.Optional Enhanced Weather Protection (EWP) Available: EWPproducts are designed to meet IP66 standards and may featurefoam rubber gaskets, sealed connections, gel-filled buttconnectors, as well as potted circuit boards with internally sealed,field-adjustable trim pots and DIP switches for easy onsiteprogramming. For more information on EWP, see DOD 859.Peel paper liner and adhere gasket to back of panel,centering over mounting holes. Caution: For roughsurfaces (ie: brick, stucco, etc.) additional caulking maybe required."Old Work" DoubleGang Rough-In Box*(Example: Allied Molded 9312box shown below, not included)*2.25"DeepMin.(4) T-10 Torx stainlesssteel, flat head, securityscrews and drive bit(included)3.65"WideMin.NECONPHEL2.84"Tall Min.INFOCTEDMarine grade 316 stainlesssteel faceplate and pushbutton switches (sealedper IP67)Grade 2 Braille Label"Help" Push to Call Button(4) Optional DryWall Screws(not included)Call Connected Red LEDEarthGroundEarth Groundthe Green/Yellowwire using theprovided wire nut"Info" ButtonLaser Etched Graphics* CAUTION: Excessive wire length and/or using a rough-in box with inadequate depth can apply force to the circuit boardcausing physical damage.Important: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation.To prevent condensation from accumulating inside the E-1600-22-IP always bring conduit into the bottom of the unit. If thisis not possible, drill a 1/4” diameter hole in the bottom of the double gang box.10

E-1600-32-IPDimensions: 5.0” x 5.0” x 2.25” (127mm x 127 x 57mm)Mounting in a Double Gang Rough-In Box (not included):Flush into walls, mounts to side of wall studs, etc.Shipping Weight: 2.12 lbs (1.0 kg)Note: For surface mount installations, use Model E-1600-30-IPwith VE-5x5 surface mount box.Front Panel Material: 14 gauge marine grade 316 brushedstainless steelNote: When mounting outside to rough or uneven surfaces(brick, stucco, etc.) apply a bead of clear silicone caulkingaround the top edge and sides of faceplate.Connections: Gel-filled butt connectorsOptional Enhanced Weather Protection (EWP) Available: EWPproducts are designed to meet IP66 standards and may featurefoam rubber gaskets, sealed connections, gel-filled buttconnectors, as well as potted circuit boards with internally sealed,field-adjustable trim pots and DIP switches for easy onsiteprogramming. For more information on EWP, see DOD 859.Note: When European CE compliance is required, mount asshown, in a metal enclosure.Peel paper liner and adhere gasket to back ofpanel, centering over mounting holes. Caution: Forrough surfaces (ie: brick, stucco, etc.) additionalcaulking may be required."Old Work" DoubleGang Rough-In Box*(Example: Allied Molded 9312box shown below, not included)(4) T-10 Torx stainlesssteel, flat head, securityscrews and drive bit(included)*2.25"DeepMin.Call Connected Red LED3.65"WideMin.NE CCONCall2.84"Tall Min.TEDMarine grade 316stainless steel faceplateand push button switches(sealed per IP67)"Help" Push to Call ButtonLaser Etched Graphics(4) OptionalDry WallScrews(not included)EarthGroundEarth Groundthe Green/Yellowwire using theprovided wire nutBL-1 grade 2 blackBraille label includedPUSH FORHELP2.20VIKING 2.40* CAUTION: Excessive wire length and/or using a rough-in box with inadequate depth can apply force to the circuit boardcausing physical damage.Important: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation.To prevent condensation from accumulating inside the E-1600-32-IP always bring conduit into the bottom of the unit. If thisis not possible, drill a 1/4” diameter hole in the bottom of the double gang box.11

E-1600-30-IPDimensions: Overall - 5.0” x 5.0” x 2.25” (127mm x 127 x57mm), Plastic Electrical Box - 4.0” x 4.0” x 2.14” (102mm x102mm x 54mm)Mounting with Plastic Rough-In Box (included): Flush intowalls, mounts to side of wall studMounting with Optional VE-5x5: Surface mount to walls, singlegang boxes, double gang boxes, posts, or to a Viking Gooseneckpedestal.Shipping Weight: 2.12 lbs (1.0 kg)Front Panel Material: 14 gauge marine grade 316 brushedstainless steel** Important: Optional Braille “Push for Help” label should beadhered to the faceplate in ADA applications. Clean surface withisopropyl alcohol, peel off backing and press firmly to the frontpanel in location as shown.Connections: Gel-filled butt connectorsOptional Enhanced Weather Protection (EWP) Available: EWPproducts are designed to meet IP66 standards and may featurefoam rubber gaskets, sealed connections, gel-filled butt connectors,as well as potted circuit boards with internally sealed, fieldadjustable trim pots and DIP switches for easy onsite programming.For more information on EWP, see DOD 859.Note: When European CE compliance is required, mount inoptional VE-5X5 metal enclosure.2.1”* Front View ofPlastic Rough-InBox (included)Peel paper liner and adhere gasketto back of panel, centering overmounting holes. Caution: For roughsurfaces (ie: brick, stucco, etc.)additional caulking may be required.4.0"(4) T-10 Torx stainless steel,flat head, security screwsand drive bit (included)Wall Stud** Wireknock outLaser Etched GraphicsTEDNECCON(2) Standardflat head drywall (sheetrock) screws(not included) OR Call Connected Red LEDMarine grade 316 stainlesssteel faceplate and push buttonswitches (sealed per IP67)Earth Ground theGreen/Yellowwire using theprovided wire nutPush to Call ButtonEarthGroundCondensation Drain Hole** Optional Braille Label5.22”3.25”(4) 0.38” diameter(for gooseneckpedestal mounting)(2) 0.2 x 0.43 slots for single gang box(4) 0.2 x 0.43 slots for double gang boxCondensationDrain Hole5.14”3.0” 3.3”***(2) 0.74"diameter3.0”2.25”Front View of OptionalVE-5x5 (not included)Rear View of OptionalVE-5x5 (not included)Optional VE-5x5 Surface Mount Box with black satin powder paint finish, notincluded (DOD 424). Optional VE-LIGHT kit can be used to illuminate the faceplatewhen used with a VE-5x5 (DOD 428). WARNING: Do NOT use a wet location box.The optional VE-5x5 SurfaceMount Box (left) is designed to besurface mounted to a single gangbox, double gang box or VE-GNPGooseneck Pedestal. For moreinformation on the VE-5x5 andVE-GNP, see DOD 424.Important: The E-1600-30-IP willNOT mount to a standard doublegang box. If your applicationsrequires a double gang box, seemodel E-1600A-32-IP on page 11.* Note: The black plastic rough-in box (part # 259576) may be purchased separately (Example: Mounting boxes to studs before thewalls are finished for flush installation). Go to www.vikingelectronics.com and click on “Spare Parts” to order these rough-in boxes.*** Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To preventcondensation from accumulating inside the E-1600-30-IP always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4”diameter hole in the bottom of the black plastic box.12

E-1600-50-IP / E-1600-52-IPThis is a E-1600-IP Emergency Phone “parts kits” without achassis. It is specifically designed to be used behind customelevator panels or with custom elevator phones. Just like allViking ADA Compliant Emergency Phones, these kitsprovide quick and reliable handsfree communication in theevent of an emergency.Optional Enhanced Weather Protection (EWP) Available:EWP products are designed to meet IP66 standards andmay feature foam rubber gaskets, sealed connections, gelfilled butt connectors, as well as potted circuit boards withinternally sealed, field-adjustable trim pots and DIP switchesfor easy onsite programming. For more information on EWP,see DOD 859.Note: When European CE compliance is required, mountin a metal enclosure.Shipping Weight: 1.0 lb (0.45 kg)Connections: Gel-filled butt connectorsStandard MicMountingBoot(2) 0.10 diametermounting holes.47 .785Mic HoleSpeaker(included).50Speaker Gasket(EWP only)Screen (included)2.602.10EWP e: Mic holes should be nearthe bottom of the boot to allowfor drainage.EWP Mic Mounting Boot: Glueto the back of your panel at anupward angle (shown left) behinda 0.10” - 0.25” diameter hole.1.0(4) 0.335 x 0.177 mountingslots for #4 or #6 studsStandard Mic Mounting Boot: Glueor screw directly behind 0.04” - 0.125”diameter hole in panel.Panel(2) 0.156 diametermounting holes2.10Relay OutputContactsMylar Speaker DimensionsConnect to "INFO" button(E-1600-52-IP only, requires a0.75" diameter mounting hole)Gray (N.C.)Blue (COM)Yellow (N.O.)Red3.50(3.58EWP)RedConnect to "PUSH FOR HELP" or"HELP" button (requires a 0.75"diameter mounting hole)BlackBlackRed (LED anode)EWP versionis connected andencapsulatedBlack (LED cathode)Clear Spacer Red RetainingLensLEDRingRed call connected LED with mounting hardware(requires a 0.250" diameter mounting hole).3.20BL-1 grade 2 blackBraille label includedPUSH FORHELPVIKING 2.40130.63(0.67EWP)1.52.0(2.04 EWP)0.15(0.19EWP)2.63(2.71 EWP)2.200.60(0.80 EWP)maximumSide View

E-1600-53-IPThis is a E-1600-IP board (PCB) only kit. This kit can be used to convert 2008or newer Viking 1600A Series Analog Emergency Phones to a VoIP version. Aspecial connector and microphone assembly is required to convert 2007 andolder Viking 1600A Series Emergency Phones. Contact Viking Technical Supportif attempting to install this kit in these older phones. This kit can also be used toreplace a damaged “IP” board in the field.Shipping Weight: 1.0 lb (0.45 kg)Connections: (1) RJ45 10/100 Base-T, (3) optional gel-filled buttconnectorsNote: When European CE compliance is required, mount in ametal enclosure.3.503.200.15(2) 0.156 diametertype 2 mounting holes2.02.631.50.6331101Connector and Wires fromExisting Standard (non EWP)1600A Series

1600A-Series phone to a VoIP version Model: E-1600-55-IP HxWxD: 5.0 x 5.0 x 2.0 Description: Universal emergency phone kit to install behind elevator panels or when a custom panel is used Model: E-1600-TP-IPEWP HxWxD: 11.75 x 9.5 x 2.0 Mounting: Flush mount Description: Direct physical replacement for Talk-A-Phone models ETP-400V or VoIP-500