WIXLIB

Blower Door and Duct Leakage TestingBlower Door Test – Building envelope test.𝑨𝑪𝑯𝟓𝟎 𝑪𝑭𝑴𝟓𝟎 𝟔𝟎𝑽𝑶𝑳𝑼𝑴𝑬NYS Code 3 ACH50*The ONLY thing you seal off are the intake and exhaust of a continuously runningERV/HRVRPH Consulting High Performance Building Specialists PO Box 448 Honeoye Falls, NY 14472

Blower Door Test FormCustomer Information:Test :Date:Time:Indoor Temperature (F):Outdoor Temperature (F):Floor Area (ft2)Conditioned Volume (ft3)Building Address: (if different from above)Tester Information:Lot cation:Phone:Comments:ft2ft3Matt BowersRPH ConsultingRESNET RTIN 425708585-750-8192CFM50 MAX based on 3 ACH50 (Code Limit)CFM50 60CFM50 MAX 0.05 VolumeVolumeHousePress.(Pa)Blower Door Ring tolerancesBlower Door TestACH50 Flow RingInstalledFlow(CFM50)Volume ft3CFM50 MAX cfm50Fan Model/SN:Manometer:Results:Total Infiltration ACH50ACH50Pass / FailRPH Consulting High Performance Building Specialists PO Box 448 Honeoye Falls, NY 14472

Mode:PR/FL @50ADJ Pa:Baseline wasunder 5 PaConfig:D matchesD Ring on BlowerDoor FanHoses:Green House(Pressure Hose) atreference port ofLeft ManometerRed Hose (FlowHose) at input portof RightManometerVERIFIED54 CFM50Volume Calculation: Done in Sketchup Make:Total Volume: 32,224 cuftRPH Consulting High Performance Building Specialists PO Box 448 Honeoye Falls, NY 14472

Total Duct Leakage Test – Prescriptive Test-Window is opened (equalize inside and outside pressuresDuctwork (and Air Handler) are pressurized with duct blaster fan to 25Pascal’sCFM is measured going through fan at that pressure – that is equivalent toCFM of leakage at that time.This number is irrelevant without the square footage of the house. The squarefootage of the house is calculated including the basement.𝐶𝐹𝑀𝑇𝑜𝑡𝑎𝑙 𝐿𝑒𝑎𝑘𝑎𝑔𝑒 𝑒𝑑 𝐹𝑙𝑜𝑜𝑟 𝐴𝑟𝑒𝑎 (𝐶𝐹𝐴)This test is only required if ductwork is outside the conditioned spaceOption 1 – Post Construction Test4 CFM / 100 sqftOption 2 – Test at Rough In, with Air Handler installed4 CFM / 100 sqftOption 3 – Test at Rough In, without Air Handler installed3 CFM / 100 sqftOption 4 – Energy Rating Index – done by a HERS RaterVaries* If ductwork in an exterior wall or garage ceiling is insulted to the exterior withadequate foam sealed in place AND the insulated cavity is accounted for in theRESCHECK the ductwork is considered within the conditioned space.* Most common houses that need this test are slab on grade with ductwork in theattic or attic truss bonus room.RPH Consulting High Performance Building Specialists PO Box 448 Honeoye Falls, NY 14472

Duct Blaster Test FormCustomer Information:Test :Date:Time:Indoor Temperature (F):Outdoor Temperature (F):Floor Area (ft2)Primary Location ofSupply DuctworkPrimary Location ofReturn DuctworkBuilding Address: (if different from above)Lot Number:Address:City:State/Zip:Tester Information:Name:Certification:Phone:Matt Bowers – RPH Consulting LLC.RESNET RTIN 4275708(585) 750-8192Comments:Test Limits: - Total Duct Leakage- Leakage (3cfm/100 sqft):- Leakage (4cfm/100 sqft):CFMCFMTest Pressure is relative to Outside PressureTotal Leakage TestOutside Leakage TestDepress/PressTest Pressure: (Pa)Baseline Duct Pressure (optional)DuctFlow Ring Fan PressPress.(Pa) Installed(Pa)Test Pa)Flow RingInstalledFan Press(Pa)Flow(cfm)Fan Model/SN: Minneapolis Duct Blaster Series B/4962Results:Fan Model/SN: Minneapolis Duct Blaster Series B/4962Outside Leakage (cfm):Outside Leakage per 100 sqft:Results:Total Leakage (cfm):Total Leakage per 100 sqft:RPH Consulting High Performance Building Specialists PO Box 448 Honeoye Falls, NY 14472

Total Duct Leakage Test – Prescriptive Test - Window is opened (equalize inside and outside pressures - Ductwork (and Air Handler) are pressurized with duct blaster fan to 25 Pascal