Transcription
GEOLAM RAINSCREEN CLADDINGPROJECT:COMPANY:GENERAL CONTRACTOR:ARCHITECT:LOCATION:
GEOLAM RAINSCREEN CLADDINGTABLE OF CONTENTS1. Vertigo 5010 Installation Guide2. Vertigo WPC Installation Guide3. Comparative Tests Brochure4. Product Specs5. Technical Data - Vertigo 50106. Technical Data - Vertigo WPC7. Geolam Warranty8. North American Installations
Architectural Eco-TechnologyVertigo 5010WHS: Wood hybrid systemDatasheetThickness: 13 mm 1 2 inTotal width: 186 mm 7 1 4 inUsable width: 170 mm 6 1 2 inSecondary moment lx (cm4): 0.56Secondary moment ly (cm4): 121.55Section tolerances in mm: 0.5 / - 1.5Section modulus Zx (cm3): 0.68Fire rating:Section modulus Zy (cm3): 12.81On request before orderCore in anodized aluminum alloy:Surfaces finish: sandedA6063S-T5Standard length: 3.0 m 9 ft 10 inCoefficient of Thermal Expansion:On order any length from:(20-100 C) : 23.4 µm/m/ C2.45 m 8 ft to 5.8 m 19 ftWeight: 1.29 kg/lm 0.87 lb / ftModulus of Elasticity: 68.6 GPaTensile Strength: 186 Mpa minCore cross section (mm2): 371.95Colors :TeakRosewoodLimbaEbony / Wenge
Vertigo 5010WHS: Wood hybrid systemDatasheetMaximum 12 mm 7 16 inMetal furring stripMinimum 3 mm 2 16 inMetal furring strip1. Weeping of condensation and aircir culation are essential to the healthof building products. Please ensure atleast 6 mm (1 4”) thickness of furringstrips and do not seal the bottom ortop of the wall.2. Geolam boards are to be mountedhorizontally, vertically, or diagonally onfurring strips or gets spaced no morethan 24 inches on center. Metalfurring strips are best but other stable,non-de teriorating materials may beused. For horizontal mounting startat the top and work down.3. Boards may be ripped (cut along theirlength) as needed.4. Recommended screws are stainlesssteel, with an austenitic structure andnon-magnetic. Recommended screwdi ameter is 4 mm, pan head with adiameter of 8.2 mm and length of19 mm.5. The boards will expand in warmerweather and contract in coolerweather. For horizontal installationcreate a fixed point near the middle ofthe board e.g. A 4 mm hole with a 4mm screw diameter. Moving out fromthis mid-point, the boards need to bepre-drilled with a 7 mm hole and thescrews loosely fastened in the middleof these holes so that the board canexpand and contract under the screwheads. Failure to do this may result inbuckling of the boards.6. The boards may be miter-cut foroutside corners.7. Exposed screws on the final boardmay be covered with caulking ifdesired or covered with any powdercoated metal piece.
Installation guideVertigo WPC Cladding BoardGeolam: a stunning alternative to wood claddingVertigo is a composite wood cladding board requiring minimum maintenance. Durable andfade resistant, it will not crack or show significant signs of age over time. It is resistant toinsect and fungus damage. It has been used by Japanese architects for more than 20 years,and in Europe for more than five, to enhance the architectural features of their buildings.Geolam Vertigo is made from recycled material and is manufactured using environmentallyfriendly processes.www.geolaminc.com
Installation guide Geolamis a composite material made from recycled wood andresins, and is easy to install. However, handling and fitting techniques are different to thosedeployed when using natural wood, so please be sure to follow the instructions below carefully Vertigo BoardStainless steel Vertigo clipsQUICK BUT IMPORTANT HINTS1. Board lengths expand and contract according to temperature. Refer to the ExpansionTable (on page 3) to compare temperature at time of installation vs maximum or minimumtemperatures anticipated. For example if boards are installed on the hottest day of theyear they will not expand.2. Allow airflow behind the boards to assist in temperature and moisture management.(See diagrams on page 10)3. Install “anchor” screws at mid point of boards to prevent “walking” (See diagram on page11).4. Cover boards with a waterproof tarp prior to installation to avoid greater-than-normalaccumulation of dust. If you fail to do this, you may need to wash the boards just priorto installation.Please refer to these installation guidelines carefully, as improper installationmay result in product malfunction and voiding the warranty. Geolam consists of,amongst other materials natural wood. Accordingly, color variation may occur.BASIC GUIDELINES FOR USING GEOLAM . Geolam composite boards consist of almost 50% natural wood fiber. As a result there will be some colorvariation from board to board. Please take this into consideration in planning your installation to maximizeaesthetic appeal. Leave a minimum interval of ¾” between the wall and the cladding boards. Thickness of the strapping orsleepers must be no less than ¾” to ensure adequate ventilation of the boards after installation, includingaround doors and window frames. Intervals between each sleeper center cannot exceed 16”. Minimum section of sleepers must be ¾” x 2”.You may install exterior insulation between the sleepers, but if you do so please make sure that yoursleepers are sufficiently deep so as not to compromise the ¾” airspace behind the boards. For example, ifyou install ¾” rigid insulation, you will need 1 ½” deep sleepers. Vertigo boards are 12 feet in length. Clips need to be applied on each sleeper, however a minimum of 3contact points and 3 clips are required per board, whatever the length of the board, i.e. for shorter lengthsof boards.www.geolaminc.com2
BASIC GUIDELINES CONT/ The cladding board is water resistant and is designed for exterior application. It contains both wood andplastic, and as such will expand and contract according to changes in temperature and humidity. The boardis at its shortest under dry, cold conditions and is longest under hot, wet conditions.For a horizontal application you are advised to drive a stainless steel screw or finishing nail through the uppertab of each board into a sleeper at, or close to, the middle of the board’s length. (This screw will be hiddenby the next board placed above it by its lower, overlapping edge). This screw will secure the board in place,ensure that all expansion and contraction activity is assigned to its ends, and will eliminate the possibility ofthe board to ‘walk’.For vertical applications the boards can be placed on a ledge or flat hooks that allow for proper drainage.All expansion and contraction activity will occur at the top of each board, so please allow for this.You will need to allow for expansion of the boards depending on the temperature when installed and theanticipated maximum temperature for your location. Similarly, you will need to anticipate contraction ofthe board depending on the temperature when installed and the expected minimum temperature for yourlocation. Please refer to the expansion table below:Expansion tableTemperature differenceºCºFFull board12 ftHalf length6 6"50905/8"5/16"Eg. Install a board at 60ºF. If maximum temperature is 100º, this will mean a temperature increase of about 40ºF,so 1/2" must be left as an end gap between two 12 ft boards. Please note that each single board will expand 1/4"on each end.FASTENING: It is preferable to use the stainless steel Vertigo clips to fasten the boards. You may face screw the boards ifdesired, but you will need to take into account the effects of expansion and contraction. For short pieces ofboard e.g. 4 ft or less, these effects will be minimal. For longer boards it will be necessary to screw theboard securely at each strapping point. Use the 2 stainless steel 1” screws provided per clip In order to avoid rust stains always use only stainless steel screws. Set your screw gun on low and fasten at reduced speed.www.geolaminc.com3
INSTALLATION HINTS F or horizontal installation: To minimize boards “walking” it is suggested that you face-screw the innertab on the upper side of each board at or near the center. Expansion and contraction will occur towards theends of each board. This screw will be hidden by the overlapping lip of the higher board when it is installed.(See diagram on page 11.) O utside corners: You may choose to not leave an expansion gap at the corner for aesthetic reasons. If so,you will need to face screw the inner tabs of each board at or near the corner and “force” the expansionand contraction towards the other end of each board. Please ensure that you allow an additional gap toaccommodate all of the expansion. e.g. 1/2”. (See diagrams on page 7.) V ertical installation: All of these installation instructions apply. Boards can be mounted either on a ledgewith proper drainage or on hooks. Each board weighs slightly more than 14 lbs. For heights greater than12 feet, you can install the boards either in rows, or in a brick pattern. In either case, please rememberthat all of the expansion will occur at the top end of each vertical board, so you will need to leave enoughroom. e.g. 1/2”. (See diagrams on pages 8 and 9.) There are several ways to minimize the appearance of butt joints, depending on your design:a. H ide the ends of the Geolam boards behind trim (pls allow expansion and contraction behind the trim)(See diagram on page 6.)b. Have the ends meet another architectural feature. The expansion gap required will appear less visiblewhen the Geolam boards meet another material e.g. stucco, brick, or another plane i.e. an inside corner.(See diagram on page 6.)c. I nside corners with Geolam boards. One board should be tucked into the corner with enough room toexpand. The other board will meet it, but with the required expansion space. (See diagram on page 7.)INSTALLATION CARE: Vertigo is a rain screen. Please ensure that your exterior wall is properly protected prior to application ofsleepers and Vertigo boards. Boards can be installed horizontally or vertically. If installed vertically it is recommended that sleepers beproperly flashed so as not to deteriorate from moisture build up. In addition, sleepers mounted horizontallywill need to have 2” gaps every 3 ft to allow a weep hole for moisture intrusion and condensation as well asair circulation behind the boards. Boards can also be installed using our hidden fasteners for soffit applications. e.g. upside down. It is recommended that a waterproof coating be applied on the exterior wall, including the sleepers, priorto installation of the Vertigo boards. Start the installation from the bottom up. For the first line of clips you can break the expansion winglet ofthe clip or use a metal profile adapted to that use (not provided). At butt joints fasten each end of the boards on double sleepers or on a support no less than 4” wide. Dothe same thing for inner and outer corners and around window frames. Boards should not be cantilevered. The Geolam fastening system is designed to move. Accordingly, you will need to ensure that the ends ofthe boards are secure either by meeting at inside or outside corners (the latter can be mitered), the additionof trim, meeting another cladding material, or other architectural feature.www.geolaminc.com4
INSTALLATION CARE CONT/ Vertigo cladding can break when hit hard. Handle the boards with care. Newly installed boards may bear an inordinately high level of dust and dirt either because they were storednear a dusty construction site or were exposed to higher than normal levels of dust at the site immediatelyafter installation. A subsequent light rain will pick up both dust and pollution in the air, add this to the duston the board, and may result in streaking when the boards dry, similar to glass streaking in a dishwasher.This ordinarily washes away in later heavy rainfalls, but can be avoided altogether if the boards are cleanedprior to, or just after, installation. Soapy water and a hose should do it. Avoid contact with fire, chimneys, or stove exhausts. Boards melt at 340ºF. Never obstruct the space between the cladding and the wall in order to allow for good aircirculation. (See page 10) It is recommended that screening or other measures be used to discourage entryof insects or vermin at the lower boards. It is recommended to affix a flashing at the bottom of the cladding in order to protect the foundation. Never immerse the cladding boards in concrete. Although the cladding boards are highly resistant to bending, they can crack under a violent impact oran extreme pressure. When installing the boards, be careful not to break the corners of the boards. Vertigo boards can be handled the same way as lumber with respect to cutting. We recommend theuse of a carbide saw blade or a light metal saw.FINISHING: You may use galvanized or aluminium profiles for corners and edges. For the installation of the last upper board, break the winglet of the clip, turn the clip upside down andscrew it through the Vertigo board. A predrill of the board is necessary for each screw. ( See cross-sectiondiagrams on page 6.)STORAGE: Store the boards on sleepers spaced no more than 16” apart and in a flat area only. Keep indoors or coverwith a waterproof tarp. If allowed to get wet during storage the dust laden water will leave spots when itdries. This does not occur when the boards are installed because of the natural cleaning process providedby wind & rain.www.geolaminc.com5
CROSS SECTION DIAGRAMS5/8"3/32"CORNERON 1rain screenVertigo5/8" x 6 1/2"3/32"BUTT ir spaceSheathingStrappingstrapping (sleeper)apping3/4" min.GeolamGeolamstainless steelscrewanti-pest guardflashingBUTT JOINTOPTION 1nerSheathingStrappingWallCORNERON 2Spline(Optional)GeolamBUTT JOINTOPTION 2appingSheathingAir spaceCORNERON 3 sion Gap6
hingAir spaceGeolamGalvanizedOutside CornerAir spaceMitred jointFINISHING - CORNER OPTIONSBUTT JOINTOPTION 1SheathingStrappingWallOUTSIDE CORNEROUTSIDE CORNEROPTION 1OPTION 2OUTSIDE CORNEROPTION 3BUTT eathingOutsideAir spaceCorner(Lathe)SheathingAir spaceSheathingSpline(Optional)StrappingMitred jointGeolamGeolamBUTT JOINTOPTION 1Expansion GapSheathingStrappingOUTSIDE CORNEROPTION 3OUTSIDE CORNEROPTION 2WallINSIDECORNERWallSheathingAir spaceMitred jointGeolamSpline(Optional)BUTT JOINTExpansion GapOPTION 2Lathe strappingScrewGeolamScrewWallGalvanizedOutside CornerWallSheathingBUTT WallJOINTOPTION 2Lathe strappingLathe strappingCaulkd jointd UTSIDE CORNEROPTION 3INSIDECORNERwww.geolaminc.comWall7Expansion Gap
VERTICAL INSTALLATION OF CLADDING BOARDOPTION 1 – 2 FACE SCREWS SUPPORTING THE WEIGHT OF THE BOARDIn the example shown, boards are installed from left to right – t his allows access to screw holes on the clips.FurringStripsmax 16” OCVertigoBoardClip2 Face ScrewsVertical installation of cladding boardOPTION 1 - 2 face screws supporting the weight of the boardIn the example shown, boards are installed from left to right –this allows access to screw holes on the clipswww.geolaminc.com8
VERTICAL INSTALLATION OF CLADDING BOARDOPTION 2 – WEIGHT OF BOARD SUPPORTED BY SS HOOK OR BRACKETFASTENED TO FURRING STRIPIn the example shown, boards are installed from left to right – t his allows access to screw holes on the clips.FurringStripsmax 16” OCVertigoBoardClipss hook or bracketVertigo Board(side view)Furring Stripmin. 2” wide by 3/4” deepScrewswww.geolaminc.comss hook or bracket9
VERTICAL INSTALLATION OF BOARDS –OPTIONS FOR INSTALLATION OF FURRING STRIPS TO CREATE AIRFLOW1. Maximum length of furring strip is 10ft., cut every 3 ft with a ¼” weep hole2. Leave a gap of 4 inches between furring strips to allow both weeping and airflow3. Air permitted to flow in and out at edges of wall.4. Air permitted to easily enter bottom of wall.5. Air permitted to easily exit top of wall.air flowStandard installation of furringwall1/4” gaps cutevery 3 ft forweep holeGeolam board4” gapFurring Stripclip10 ftair flowair flowair flowair flowair flow behind boardsair flowStaggered installation of furringwall1/4” gaps cutevery 3 ft forweep holeGeolam board4” gapFurring Stripclip10 ftair flowair flowair flowwww.geolaminc.comair flowair flow behind boards10
INSTALLATION OF “ANCHOR” SCREWS AT MID POINTOF BOARDS TO PREVENT “WALKING”Anchor nails or screwsFasten nail or screwon upper part at approx.mid-point of boardwww.geolaminc.com11
How Geolamstacks up againstthe competitionGeolam comes out on top, after independent testing.To determine how well Geolam compares against its competition, independent testingfacility Compositology LLC conducted extensive tests. In addition to the standard tests,Geolam and its competitors were subjected to a series of tests never done before. Thesetests measured slip resistance (both wet and dry) and water absorption (both fresh andsalt water). In both cases, Geolam proved to be superior by impressive margins. It also wasshown to be stronger than its competition. The results can be seen on the following pages.The safest decking product in dry and wet conditions.Slip-resistance is a critical safety issue and some products have significantly different slip-resistance valueswhen wet. Geolam’s excellent slip-resistance creates surfaces that are safe, reliable and with minimal riskeven when wet.Slip Resistance0.80Mostconsistentperformancebetween wetand dry0.700.6337% moreslipperywhen wet47% moreslipperywhen wet0.6944% moreslipperywhen wet0.60SLIP INDEX(along the axis of extrusion)Safestwet productOnly 9%more slipperywhen Azek TerraFiberonOutdoorFlooringTimberTechDock exTranscendsCOMPETITIVE DECKING BRANDS** All brand names trademarked to their companies.
38% greatercompressionstrength thanthe (psi)(psi)Stronger than other leading decking pression Strength3,0963,0963,096(PRESSURE REQUIRED TO CRUSH THE scendsTrexTranscendsAzekAzek ingFlooringOutdoorFlooringCOMPETITIVECOMPETITIVE DECKINGDECKING BRANDS*BRANDS*Azek TerraTimberTechTimberTechDock SiderSiderDockTimberTechDock ShieldShieldMoistureShieldCOMPETITIVE DECKING BRANDS*4,5004,500Geolam showssuperiorstrength evenunder extremepressureSTRESSSTRESSSTRESS@ 500Stress @ 3%4,0084,0084,008(PRESSURE REQUIRED TO DEFORM THE BOARD BY echTimberTechDock SiderSiderDockTimberTechDock ETITIVEDECKINGCOMPETITIVEDECKINGAzek TerraTerraAzekAzek TerraBRANDS*BRANDS*COMPETITIVE DECKING assportTensile Strength3,0003,000Highesttensilestrength ofall HSTRENGTH(psi)(psi)(psi)3,0002,5002,500(PRESSURE REQUIRED TO BREAK A BOARD BY PULLING ALONG ITS exTranscendsTranscendsTrexTranscendsAzekAzek TerraTerraFiberonFiberonOutdoorOutdoorAzek TIVECOMPETITIVE ssportBRANDS*BRANDS*COMPETITIVE DECKING BRANDS*TimberTechTimberTechDockDock SiderSiderTimberTechDock MoistureShieldShieldMoistureShield** AllAll brandbrand namesnames trademarkedtrademarked toto theirtheir companies.companies.* All brand names trademarked to their companies.
The lowest water absorption rate in fresh and salt water.Testing proves that the water absorption rates of some composite decking products may increasesignificantly when exposed to water for an extended period. Composite decking products with higherwater absorption rates can experience dimensional change, decreased mechanical performance and aremore susceptible to mold. When submerged in salt water, some products had an increase in their waterabsorption rates of more than 90%. That degraded their structure and their performance. Geolamoutperformed on all counts.WATERWATERABSORPTIONABSORPTIONRATE 4.0%5.0%3.0%4.0%2.0%3.0%1.0%2.0%0.0%1.0%0.0%Fresh Water Absorption51% increase inwater absorption withprolonged exposure500 hrs1000 hrs1.7%1.7%500 hrs1000 G BRANDS*PassportShieldDock SiderTimberTechDock SiderMoistureShieldCOMPETITIVE DECKING BRANDS*WATERWATERABSORPTIONABSORPTIONRATE ngAzek TerraAzek TerraSalt Water stwaterabsorptionrateSuperiorperformancein salt water92% increasewith prolongedexposurein salt water1.5%1.5%500 hrs1000 hrs2.0%500 hrs1000 cendsAzek TerraFiberonOutdoorFlooringTrexAzek TerraFiberonMoistureTimberTechCOMPETITIVEDECKING BRANDS*TranscendsOutdoorShieldDock SiderFlooring* All brand names trademarked to their companies.COMPETITIVE DECKING BRANDS*TimberTechDock SiderMoistureShield* All brand names trademarked to their companies.Confirmed by independent testing. Compositology LLC is a leading independent resourcefor both standardized, industry-accredited testing and real-world comparative testing. Standardized tests work well fordiscovering specific mechanical properties of a material, such as bending strength and stiffness. Compositology conductsreal-world testing as well, to get results proven in actual working conditions. Learn more at www.compositology.com.
Slip resistanceMoisture resistanceFade resistanceMold resistanceRecyclableLongevityMaintenanceDuo DeckingIpéTrexrecycled wood and high qualitythermoplastic (polypropylene)exotic wood found mainly inCentral and South Americarecycled wood and plastic filmand bags HHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHHEco Mark CertificationcertificarkmionatThe Japan Environment Association certifies products thatcontribute to environmental preservation with the Eco Marklogo, attached to products that help protect the environment.Products sold under the Geolam brand have successfullyobtained this certification under Product Category No.123“Construction product using recycled material” adoptedin April 2002.ecoCertification N 07123069 (Since April 2002)N 07 1 23069To learn more about the advantages of Geolam, our complete product line,or for any other information, please visit our website or contact us at any time.Geolam, Inc.North America: 9 Shorncliffe Ave., Toronto, ON Canada M4V 1S9Toll free: 1-877-627-3530 Tel: 416-548-7450 info@geolaminc.comwww.geolaminc.com
SECTION 07 46 43COMPOSITE SIDING1.1 SECTION INCLUDESA.Composite Hybrid Cladding1.2 RELATED SECTIONSA.Section 06 16 00 - Sheathing1.3 REFERENCESA.JIS International: (Japanese Industrial Standards)1.JIS K 7112 Specific Density g/cm3 Value 1.272.JIS K 7191 Deformation Temperature C Value- 116 degrees3. JIS K7197 Thermal Expansion Coefficient mm/C Value 3.6 x 10/- 54.JIS A5909 Moisture Absorption (24 hrs @ 68 F) Value- .25. JIS A5909 Linear Expansion Value Zero6. JIS 5721 Aging Test Value - 5%7. Core in Anodized Aluminum Alloy: A60635S- T5B.Submit under provisions of Section 01300.C.Product Data: Manufacturer's data sheets on each product to be used, including:1.Preparation instructions and recommendations.2.Storage and handling requirements and recommendations.3.Installation methods including anchorage details.4.Cleaning and maintenance instructions.D.Shop Drawings: Provide shop drawings indicating details of construction, anchorageand installation. Include statement that anchorage methods comply with applicablebuilding codes and loadings for the type of framing and condition of the supportingconstruction and details.E.Selection Samples: Submit two sets of samples, 6 inches in length, showingavailable materials, colors, patterns, textures, and finishes.F.Verification Samples: For each product specified, two samples 6 inches in length,representing materials, colors, patterns, textures, and finishes to be installed.1.4 DELIVERY, STORAGE AND HANDLINGA.Deliver, store and handle materials and products in strict compliance withmanufacturer's instructions and recommendations and industry standards. Protectfrom damage.B.Store products with manufacturer's labels on the individual boxes and unit shroudsuntil ready for installation.1.5 WARRANTY06732- 1
A.Manufacturer's Warranty:1.Warranty Period: 10 years.PART 2 PRODUCTS2.1 MANUFACTURERSA.Acceptable Manufacturer: Geolam,Inc. which is located at: 9 Shorncliffe Ave.;;Toronto, ON M4V1S9;; Tel: 416- 548- 7450;; Email: rfactor@geolaminc.com. Web:www.geolaminc.comB.Substitutions: Not permitted.2.2 COMPOSITE HYBRID CLADDINGA.Vertigo 5010 Wood Hybrid Cladding1.Description: Hot Co- Extrusion of Aluminum and Wood Composite technology2.Color: Teak3.Color: Rosewood4.Color: Ebony5. Color: Moleskin6.Width- 7 ¼” (6 ½” Exposure)7. Depth- 1/2”8. Length- 12’ Standard- (Custom to 19’)9. Weight- .080 lb/ft.PART 3 EXECUTION3.1 PREPARATIONA.Prepare substrate using the methods recommended by the manufacturer forachieving the best result for the substrate under the project conditions. If preparationis the responsibility of another installer, notify Architect in writing of deviations frommanufacturer's recommended installation tolerances and conditions.B.Do not proceed with installation until substrates have been properly prepared anddeviations from manufacturer's recommended tolerances are corrected.Commencement of installation constitutes acceptance of conditions.3.2 INSTALLATIONA.Vertigo 5010 Hybrid Installation: Install in accordance with manufacturer's writteninstructions and recommendations.B. Protection: Protect installed work from damage due to subsequent constructionactivity on the site.C.Clean using materials recommended by the manufacturer to remove stains, dirt anddebris prior to final acceptance.END OF SECTION06732- 2
SECTION 07 46 43COMPOSITE SIDING1.1SECTION INCLUDESA.1.2RELATED SECTIONSA.1.3Composite SidingSection 06 16 00 - Sheathing.REFERENCESA.ASTM/AAMA/FL. & Miami Dade1.2.3.4.5.6.7.B.ASTM D635 – Standard Test Method for Rate of Burning and/orExtent and Time of Burning of Plastics in a Horizontal PositionASTM D 1929- Standard Test Method for Determining IgnitionTemperature of PlasticsASTM D 2843- Density of Smoke from the Burning orDecomposition of Plastics.ASTM E 84- Standard Test Method for Surface BurningCharacteristics of Building MaterialsASTM E330- Standard Test Method for Structural Performanceof Exterior Windows, Doors, Skylights and Curtain Walls byUniform Static Air PressureAAMA 509-Cladding Drainage and VentilationFL. Building Code and Miami Dade ApprovalJIS International: (Japanese Industrial Standards)1.2.3.4.5.6.JIS K 7112 Specific Density g/cm3 Value 1.27JIS K 7191 Deformation Temperature C Value-116 degreesJIS K7197 Thermal Expansion Coefficient mm/C Value 3.6 x 10/-5JIS A5909 Moisture Absorption (24 hrs @ 68 F) Value-.2JIS A5909 Linear Expansion Value ZeroJIS 5721 Aging Test Value -5%C.Submit under provisions of Section 01300.D.Product Data: Manufacturer's data sheets on each product to be used, including:1.Preparation instructions and recommendations.2.Storage and handling requirements and recommendations.3.Installation methods including anchorage details.4.Cleaning and maintenance instructions.E.Shop Drawings: Provide shop drawings indicating details of construction, anchorageand installation. Include statement that anchorage methods comply with applicable074643-1
building codes and loadings for the type of framing and condition of the supportingconstruction and details.1.41.5F.Selection Samples: Submit two sets of samples, 6 inches in length, showingavailable materials, colors, patterns, textures, and finishes.G.Verification Samples: For each product specified, two samples 6 inches in length,representing materials, colors, patterns, textures, and finishes to be installed.DELIVERY, STORAGE AND HANDLINGA.Deliver, store and handle materials and products in strict compliance withmanufacturer's instructions and recommendations and industry standards. Protectfrom damage.B.Store products with manufacturer's labels on the individual boxes an
Geolam boards are to be mounted horizontally, vertically, or diagonally on furring strips or gets spaced no more than 24 inches on center. Metal furring strips are best but other stable, non-deteriorating materials may be used. For horizontal mounting start at the top and work down. 3. Boards may be ripped (cut along their length) as needed. 4.
