Transcription
CG75-85Parts ManualContinental Girbau, Inc. 2500 State Road 44Oshkosh WI 54904Telephone: (920) 231-8222 / Fax: (920) 231-4666www.cont-girbau.com010901JCARRITA/rarCGIA Part No. 450313
Retain This Manual In A Safe Place For Future ReferenceThis product embodies advanced concepts in engineering, design, and safety. If this product is properly maintained, it willprovide many years of safe, efficient, and trouble-free operation.ONLY qualified technicians should service this equipment.OBSERVE ALL SAFETY PRECAUTIONS displayed on the equipment or specified in the installation manual included withthe dryer.The following “FOR YOUR SAFETY” caution must be posted near the dryer in a prominent location.FOR YOUR SAFETYPOUR VOTRE SÉCURITÉDo not store or use gasoline orother flammable vapors andliquids in the vicinity of this orany other appliance.Ne pas entreposer ni utiliser d’essenceni d’autres vapeurs ou liquidesinflammables à proximité de cetappareil ou de tout autre appareil.We have tried to make this manual as complete as possible and hope you will find it useful. The manufacturer reserves theright to make changes from time to time, without notice or obligation, in prices, specifications, colors, and material, and tochange or discontinue models.ImportantFor your convenience, log the following information:DATE OF PURCHASEMODEL NO.CG75-85DISTRIBUTOR’S NAMESerial Number(s)Replacement parts can be obtained from your distributor or Continental Girbau, Inc. When ordering replacement parts fromthe factory, you can FAX your order to Continental Girbau, Inc. at (920) 231-4666 or telephone your order directly to theContinental Girbau, Inc. Parts Department at (920) 231-8222. Please specify the dryer model number and serial number inaddition to the description and part number, so that your order is processed accurately and promptly.The illustrations on the following pages may not depict your particular dryer exactly. The illustrations are a composite of thevarious dryer models. Be sure to check the descriptions of the parts thoroughly before ordering.“IMPORTANT NOTE TO PURCHASER”Information must be obtained from your local gas supplier on the instructionsto be followed if the user smells gas. These instructions must be posted in aprominent location near the dryer.
Table of ContentsControl Door Assembly . 2Phase 5 OPL Microprocessor Control Panel Assembly . 3Phase 5 Coin Microprocessor Control Panel Assembly . 4Dual Timer “Tap Touch” Controls . 5Coin and OPL Control Box Assembly . 6Coin Vault Assembly . 7Front Panel Assembly . 8Main Door “Steel” Assembly . 9Main Door Switch Assembly . 10Basket (Tumbler)/Support Assemblies . 11Lint Drawer/Lint Drawer Switch Assembly . 12Idler Bearing Assembly . 13Basket (Tumbler) Bearing Assembly . 14, 15Non-Reversing Motor Mount Assembly . 16, 17Reversing T.E.F.C. Motor Mount Assembly . 18, 19Sensor Bracket Assemblies . 20, 21Direct Spark Ignition (DSI) Burner Assembly . 22, 23Air Operated Steam Damper Assembly . 24, 25Electric Oven Assembly . 26, 27Sail Switch Assembly . 28Single-Phase (1ø) Motor, Electric Relay Panel Assembly . 293-Phase (3ø) Motor, Electric Relay Panel Assembly . 30460-480 VAC 3-Phase (3ø) Motor, Electric Relay Panel Assembly . 31Reversing Electric Relay Panel Assembly . 32460-480 VAC Reversing Electric Relay Panel Assembly . 33Outer Top/Back Guard Assemblies . 34Electric Oven Component Application Chart . 35Microprocessor Coin Acceptors Listing . 36Additional Parts Available . 37
2Control Door AssemblyIllus. No.Part riptionWhite Control Door Assembly(includes illus. nos. 1, 3, 5, and 8)#10-32 x 3/4” Phillips Pan Head Machine ScrewDouble Sided Tape#10-16 x 3/4” TORX Plus BTN Type 125 IP TORX Plus Bit (for removal of TORX head screw)Neoprene Sponge Tape (sold by the foot)#10-32 Multi-Thread U-NutControl Door Rod Support CatchControl Door Text Back PlateControl Door Support RodControl Door Rod Retainer ClipCONTINENTAL GIRBAU, INC.
Phase 5 OPL Microprocessor Control Panel AssemblyIllus. No.1234567Part 15031313604811122113DescriptionOPL English Keyboard (touch pad) Label AssemblyOPL Stick-On Labels (English Only).Not Illustrated3-Language OPL Stick-On Labels.Not Illustrated(Spanish, Italian, and Hebrew)3-Language OPL Stick-On Labels.Not Illustrated(English, Spanish, and Hebrew)5-Language OPL Stick-On Labels.Not Illustrated(Italian, Dutch, French, German, and Chinese)Phase 5 Microprocessor Control Panel ONLYPhase 5 Microprocessor Control Panel ONLY with Battery BracketPhase 5 OPL Non-Reversing Microprocessor Control Panel AssemblyComplete(includes illus. nos. 1 through 6)Phase 5 OPL Reversing Microprocessor Control Panel Assembly Complete(includes illus. nos. 1 through 6)Phase 5 OPL Non-Reversing Microprocessor Controller (computer) ONLYPhase 5 OPL Reversing Microprocessor Controller (computer) ONLYPhase 5 Battery Clip#6 Star Washer#6-32 x 1/4” Phillips Round Head Machine Screw#10-16 x 1/2” TORX Plus BTN Type 11/8-Amp (slo blo) FuseIMPORTANT: Check label on computer chip to verify correct part number for controller (computer).CONTINENTAL GIRBAU, INC.
4Phase 5 Coin Microprocessor Control Panel AssemblyIllus. No.1234567891011Part 7021880772122800136048113111DescriptionCoin Keyboard (touch pad) Label AssemblyPhase 5 Coin Control Panel Assembly(includes illus. nos. 1, 2, 4 through 6, and 11)Phase 5 Coin Control Panel Assembly with Battery Option(includes illus. nos. 1, 2, 4 through 6, and 11)Coin Control Panel ONLYCoin Control Panel ONLY with Battery Bracket#10-16 x 1/2” TORX Plus BTN Type 1Phase 5 Coin Microprocessor Controller (computer) ONLYPhase 5 Battery Clip#6 Star Washer#6-32 x 1/4” Phillips Round Head Machine ScrewCoin Acceptor(refer to Microprocessor Coin Acceptors Listing on page 36)Optic Switch ONLYOptic Switch Connector ONLYMicroprocessor Socket ONLYSingle Coin Optical Switch HarnessMicroprocessor (female) Pin Extraction Tool1/8-Amp (slo blo) FuseIMPORTANT: Check label on computer chip to verify correct part number of controller (computer).CONTINENTAL GIRBAU, INC.
Dual Timer “Tap Touch” ControlsIllus. No.Part 15 Minute Timer - 24 VAC60 Minute Timer - 24 VACRed Pilot Light - 24 VAC“Tap Touch” SwitchRelay Single-Pole Single Throw (SPST) 24v30-Position Terminal Block#6-32 Pal NutDual Timer Panel Complete(includes illus. nos. 1 through 15)Dual Timer Panel ONLY#6 Star Washer#6-32 Hex Nut#10-24 x 1/2” Phillips Pan Head Machine Screw#8-32 x 1/4” Phillips Round Head Machine ScrewDual Timer Panel OverlayPure Touch Knob with Red PointerPure Touch Knob with Blue PointerCONTINENTAL GIRBAU, INC. 5
6Coin and OPL Control Box AssemblyIllus. No.12--34*Part ion15-Pin Microprocessor Controller (computer) ConnectorSocket Terminal ONLYPin/Socket Extraction Tool#8-18 x 7/16” Phillips Pan Head TEK ScrewReversing Timer 24v (for reversing dual timer models Only)As required.CONTINENTAL GIRBAU, INC.
7Coin Vault AssemblyIllus. 11411123*Part No.DescriptionMicroprocessor Coin Vault Assembly Complete(includes illus. nos. 1 through 6)Microprocessor Coin Vault ONLYCam For 1/4 Turn Lock ONLY1/4 Turn Lock with Key and Cam1/4 Turn Mer-Pel Key ONLY1/4 Turn Coin Box Assembly(includes illus. nos. 2 through 5)1/4 Turn Coin Box ONLY without FaceplateHigh Security (Greenwald) Coin Box ONLY with Key1/4 Turn Coin Box Faceplate ONLY1/4-20 Free Spin Wash NutControl Door Support RodControl Door Rod Retainer ClipControl Door Rod Support CatchSpecify key number when ordering.CONTINENTAL GIRBAU, INC.
8Front Panel AssemblyIllus. No.Part 819871161542152DescriptionWhite Front Panel Assembly(includes illus. nos. 1, 4, 5, and 6)#10-16 x 1/2” TORX Plus BTN Type 125 IP TORX Plus Bit (for removal of TORX head screw)Main Door Hinge(refer to Main Door “Steel” Assembly on page 9)Front Panel Trim AssemblyFriction Door Latch(includes illus. nos. 5 and 6)5/32” Pop RivetCONTINENTAL GIRBAU, INC.
Main Door “Steel” AssemblyIllus. No.Part 11DescriptionWhite Main Door Assembly Complete(includes illus. nos. 1, 2, and 8 through 14)Door GasketClear Gasket Adhesive (10.7 oz. cartridge)Black Gasket Adhesive (10.7 oz. cartridge)White Top Hinge Block Assembly(includes illus. nos. 3 and 4)1/4-20 x 3/4” Black Cap Head Setscrew1/4” Nylon WasherWhite Bottom Hinge Block Assembly(includes illus. nos. 5, 6, and 7)1/4-20 x 3/4” Black Cap Head SetscrewContinental Girbau, Inc. Logo Plate1/4-20 Free Spin Wash Nut#10-32 Black Hex Acorn NutDoor Latch ScrewWhite Small Cold Rolled Steel (CRS) Door Handle1/4-20 Free Spin Wash Nut20-7/16” Door GlassClear Glass Adhesive (10.3 oz. cartridge)Black Glass Adhesive (10.3 oz. cartridge)CONTINENTAL GIRBAU, INC. 9
10Main Door Switch AssemblyIllus. No.Part 81216222121171503012Description#6-32 x 7/8” Phillips Pan Head Machine Screw#6-32 Hex Nut#6 Star WasherDoor SwitchFlag TerminalWhite Main Door Switch Housing ONLYWhite Main Door Switch Housing Complete(includes illus. nos. 1, 2, 3, 4, and 6)#8-18 x 7/16” Phillips Pan Head TEK ScrewCONTINENTAL GIRBAU, INC.
Basket (Tumbler)/Support AssembliesIllus. No.Part 14414441134567**891011---DescriptionBasket (tumbler) ONLY without Felt CollarBasket (tumbler) and Support Assembly Complete(includes illus. nos. 1 through 10)#10-16 x 1/2” TORX Head Crimptite ScrewTORX Hand Driver (for removal of TORX head screw)Basket (tumbler) Rib ONLY5/16-18 x 3/4” Socket Button Head Screw3/8-16 x 37” Tie Rod3/8” Flat WasherBasket (tumbler) Support ONLY3/8-16 Hex Nut3/8” Lock Washer3/8” Flat WasherFelt Collar ONLY#847 Adhesive for Felt Collar* Felt collar is not included and must be ordered separately.** Non-reversing and reversing models use the same basket (tumbler) support.CONTINENTAL GIRBAU, INC. 11
12Illus. No.Lint Drawer/Lint Drawer Switch AssemblyPart tionLint Drawer Assembly (white)(includes illus. nos. 1 and 2)Gasket (sold by the foot)Lint Drawer Switch4-Pin Socket Connector ONLYSocket Terminal ONLYPin/Socket Extraction ToolLint Drawer Switch Box Assembly(includes illus. nos. 3 through 6)Lint Drawer Switch Box Cover ONLY#8-18 x 7/16” Phillips Pan Head TEK ScrewPin Terminal ONLY4-Pin Connector ONLYCONTINENTAL GIRBAU, INC.
13Idler Bearing AssemblyIllus. No.123Part 0509222111Description5L-680 V-Belt (basket [tumbler] to idler)14” x 3” Compound Pulley4L-720 V-Belt (idler to motor)For Non-Reversing Models ONLY4L-650 V-Belt (idler to motor)For Reversing Models ONLY5/16-18 x 1” Allen Setscrew3/16” x 3/16” x 1-3/8” KeyIdler Bearing Assembly Complete(includes illus. nos. 5 through 12)3/8-16 x 1” Hex Head Machine Bolt3/8” Lock Washer3/8” Flat WasherIdler Square Washer5/16-18 Hex Nut5/16-18 x 3” Hex Head Machine BoltCONTINENTAL GIRBAU, INC.
14Basket (Tumbler) Bearing AssemblyCONTINENTAL GIRBAU, INC.
Basket (Tumbler) Bearing AssemblyIllus. No.1234Part iption1-3/4” Flange Bearing9/16” Lock Washer9/16-12 Hex NutPillow Block Bearing Assembly Complete(includes illus. nos. 4 through 17)Pillow Block Bearing Assembly Complete(includes illus. nos. 4 through 18)For Microprocessor Models with Optional Rotational Sensor ONLYPillow Block Bearing Platform ONLYPillow Block Bearing Platform ONLYFor Microprocessor Models with Optional Rotational Sensor ONLY1-3/8” Pillow Block Bearing1-3/8” Pillow Block BearingFor Microprocessor Models with Rotational Sensor ONLY3/8-16 x 2” Hex Bolt3/8” Flat Washer3/8” Flat Washer3/8” Lock Washer3/8-16 Hex Nut5/16-24 x 3/8” Setscrew5/16-18 Hex Nut5/16-18 x 1-1/2” Tap Bolt5/16” Lock Washer3/8” Flat Washer5/16-18 x 3/4” Tap BoltSintered 8 Magnet(for microprocessor models with optional rotational sensor Only)Rotational Sensor Assembly(for microprocessor models with optional rotational sensor Only)Shaft Key (for reversing models Only)18” Pulley (for non-reversing models Only)18-3/4” Pulley (for reversing models Only)1” Taper Lock Bushing (for reversing models Only)5L-680 V-Belt (basket [tumbler] to idler)5/16-18 x 1-1/2 Allen Setscrew5/16-18 Hex NutCONTINENTAL GIRBAU, INC. 15
16Illus. No.123456Non-Reversing Motor Mount AssemblyPart 111444Description4L-720 V-Belt (idler to motor)3/16” x 3/16” x 1” Key5/8” x 2-1/4” Motor Pulley (60 Hz Only)5/8” x 2-1/2” Motor Pulley (50 Hz Only)5/16-18 x 3/4” Tap Bolt5/16” Lock Washer5/16” Flat WasherCONTINENTAL GIRBAU, INC.
Non-Reversing Motor Mount AssemblyIllus. No.78910111213141516171819202122*Part 006120200100075122111811151Description1 HP 120/208/230v 1ø 60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.)Motor with Plug (56Z frame)(for models mfd. as of September 7, 2002)3/4 HP 120-240v 1ø 60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.)Motor with Plug (56Z frame)(for models mfd. prior to September 7, 2002)1 HP 240v 1ø 50 Hz Motor with PlugSocket Terminal ONLYPin/Socket Extraction Tool8-Pin Housing Connector5/16-18 Hex Nut5/16” Lock Washer5/16” Flat WasherNeoprene Sponge Tape (sold by the foot)5/16-18 Tinnerman NutNon-Reversing Motor Mount ONLY (56Z frame)1 HP 120/230v 1ø 60 Hz Totally Enclosed, Fan-Cooled (T.E.F.C.)Motor Mount Assembly with Plug Complete(includes illus. nos. 2 through 7 and 13 through 20)1 HP 208-230v 3ø 60 Hz (3/4”) Shaft Non-Reversing Motor MountAssembly Complete(includes illus. nos. 2 through 6 and 13 through 22)3/4” S.A.E. Flat Washer12-1/2” Impellor (1/2” bore)(for all models mfd. prior to September 7, 2002)16” Impellor (3/4” bore)(for 1ø models mfd. as of September 7, 2002and for 3ø models mfd. as of January 1, 2003)16” Impellor (1/2” bore)(for 3ø models mfd. between September 7, 2002 and January 1, 2003)3/16” x 3/16” x 1-7/8” Key1/2” S.A.E. Flat Washer1/2-20 Left Hand Jam Nut3/8” x 90 Connector1 HP 200/230/460v 3ø 50/60 Hz Motor(for models mfd. as of December 23, 2002)1 HP 208/230/240/460v 3ø 50/60 Hz Motor(for models mfd. prior to December 23, 2002)Specify voltage when ordering.CONTINENTAL GIRBAU, INC. 17
18Reversing T.E.F.C. Motor Mount AssemblyCONTINENTAL GIRBAU, INC.
Reversing T.E.F.C. Motor Mount AssemblyIllus. No.Part cription4L-650 V-Belt (to idler assembly)3/16” x 3/16” x 1” Key5/8” x 2-1/4” Motor Pulley (60 Hz Only)3/8” x 90 Connector1/2 HP 208/230/380/460v 3ø 50/60 Hz Totally Enclosed, Fan-Cooled(T.E.F.C.) Motor (56Z frame)5/16-18 x 3/4” Tap Bolt5/16” Lock Washer5/16” Flat Washer1 HP 200-230/460 3ø 60 Hz Totally Enclosed, Fan-Cooled Motor(for models mfd. as of February 10, 2003)1/2 HP 220/230/380/460v 3ø 50/60 Hz Totally Enclosed, Fan-Cooled(T.E.F.C.) Motor with 3/4” Shaft (56Z frame)(for models mfd. prior to February 10, 2003)3/8” x 90 Connector5/16-18 x 3/4” Tap Bolt5/16” Lock Washer5/16” Flat Washer5/16-18 Tinnerman Nut5/16-18 Hex Nut5/16” Lock Washer5/16” Flat WasherReversing Motor Mount ONLY (56Z frame)1 HP 60 Hz Reversing Totally Enclosed, Fan-Cooled Motor MountAssembly(includes illus. nos. 2 through 14 and 18 through 24)Neoprene Sponge Tape (sold by the foot)3/4” S.A.E. Flat Washer3/16” x 3/16” x 1-7/8” Key16” Impellor (3/4” bore)(for models mfd. as of January 20, 2003)16” Impellor (1/2” bore)(for models mfd. between September 2, 2002 and January 20, 2003)12-1/2” Impellor (1/2” bore)(for models mfd. prior to September 2, 2002)1/2” S.A.E. Flat Washer1/2-20 Left Hand Jam Nut* Check part number on motor data label to verify correct motor.** Specify voltage when ordering.*** As required.CONTINENTAL GIRBAU, INC. 19
20Sensor Bracket AssembliesCONTINENTAL GIRBAU, INC.
Sensor Bracket AssembliesIllus. No.Part ” Temperature Sensor Probe Assembly(includes illus. nos. 1 and 5 through 8)225 Manual Reset Thermostat#6 Star Washer#6-32 Hex NutInsulated Female TerminalSocket Terminal ONLYPin/Socket Extraction Tool4-Pin Socket Connector ONLY1/4” Tinnerman Push On Fastener#6-32 x 1/4” Phillips Round Head Machine ScrewMicroprocessor Sensor Bracket Assembly Complete(includes illus. nos. 1 through 10)Universal Sensor Bracket ONLY4-Pin Connector ONLYPin Terminal ONLY#8-18 x 7/16” Phillips Pan Head TEK Screw#6-32 x 1/4” Phillips Round Head Machine Screw130 Large Thermostat150 Large Thermostat225 Manual Reset Thermostat180 Large Thermostat#6 Star Washer#6-32 Hex NutSensor Jumper ONLYInsulated Female TerminalSocket Terminal ONLY4-Pin Socket Connector ONLYSensor Bracket Harness Assembly(includes illus. nos. 22, 23, and 24)Noncomputer Sensor Bracket Assembly Complete-Includes Thermostats(includes illus. nos. 14 through 25)Universal Sensor Bracket ONLY4-Pin Connector ONLYPin Terminal ONLYPin/Socket Extraction Tool#8-18 x 7/16” Phillips Pan Head TEK ScrewCONTINENTAL GIRBAU, INC.
22Illus. No.1*Direct Spark Ignition (DSI) Burner AssemblyPart nNatural Gas Burner Assembly Complete(includes illus. nos. 1 through 5 and 7 through 31)For Models Mfd. with Natural Gas ONLY(burner orifice not included and must be ordered separately)Liquid Propane (L.P.) Gas Burner Assembly Complete(includes illus. nos. 1 through 5 and 7 through 31)For Models Mfd. with Liquid Propane (L.P.) Gas ONLY(burner orifice is not included and must be ordered separately)Burner Box ONLYLarge Burner Tube3/4” Direct Spark Ignition (DSI) Manifold (4-port)Bracket For Horizontal Facing Gas Valve1/2” 24 VAC Redundant (natural gas) Gas Valve1/2” 24 VAC Direct Spark Ignition (DSI) Liquid Propane (L.P.)Gas Valve AssemblyCG75-85 Liquid Propane (L.P.) Conversion Kit#30 Burner Orifice (natural gas) ONLY#49 Burner Orifice (liquid propane [L.P.] gas) ONLYCONTINENTAL GIRBAU, INC.
Direct Spark Ignition (DSI) Burner Assembly (continued)Illus. No.Part n#8-32 x 1/2” Pan Head Machine Screw#8-32 Pal Nut#10-16 x 1/2” Hex Washer TEK ScrewIgnitor Probe Assembly with 19” Leads#10-16 x 1/2” Hex Head TEK Crimptite Screw#6-32 Hex NutDirect Spark Ignition (DSI) Module with Three (3) TriesJohnson Controls Direct Spark Ignition (DSI) Module Mounting Bracket1/2” x 1-1/2” Long Black Nipple1/2” Street Elbow1/2” Black Union1/2” x 29-1/8” NippleHi-Limit Mounting Bracket#6-32 Pal Nut#6-32 x 1/2” Phillips Round Head Machine Screw330º Hi-Limit Manual ResetPipe Bracket (bent)3/4” to 1/2” Reducing CouplingTwin Speed NutSail Switch Box Cover and Bracket ONLY(refer to Sail Switch Assembly on page 28)Sail Switch ONLY#4 x 3/4” Pan Head “A” Machine ScrewSail Switch Actuator RodSail Switch Damper (flat)1/8” Push On FastenerSteam to Gas Interface Plate.Not Illustrated* Consult factory for elevations over 2,000 feet.** Needed when converting from steam to gas heat.CONTINENTAL GIRBAU, INC.
24Air Operated Steam Damper AssemblyCONTINENTAL GIRBAU, INC.
Air Operated Steam Damper AssemblyIllus. No.Part 11111441111112221221DescriptionSteam Coil Assembly5/16” Lock Washer5/16-18 Hex Nut1/4-20 Hex Nut1/4” Lock WasherSteam Damper Hinge AssemblySteam Damper Assembly(includes illus. nos. 7, 10, and 11)1/4” Lock Washer1/4-20 Hex NutSteam Damper Gasket (sold by the inch)Steam Damper Foam (68-1/2” length)7/16-20 Stainless Steel Acorn Nut7/16-20 Hex Nut1-1/4” Bore x 3” Stroke PistonPiston Support Bracket1/4-20 Hex Nut1/4” Lock Washer1/4” x 1/8” Connector1/4” Tubing (sold by the foot)1/4” x 1/8” Connector1/8” Needle Valve1/8” Close Nipple3-Way Micro Valve-24 VAC#6-32 x 1” Phillips Round Head Machine Screw#6 Star Washer#6-32 Hex NutMicro Valve Support Bracket1/4-20 Hex Nut1/4” Lock Washer1/8” N.P.T. Silencer (muffler)CONTINENTAL GIRBAU, INC. 25
26Electric Oven AssemblyELECTRIC OVEN (FRONT VIEW)ELECTRIC OVEN (REAR VIEW)CONTINENTAL GIRBAU, INC.
27Electric Oven AssemblyIllus. No.Part 28293031***DescriptionLarge Electric Oven Box ONLYElectric Oven Assembly CompleteElectric Element#10-16 x 1/2” Hex Washer TEK ScrewSail Switch Box with Bracket and Cover ONLYSail Switch Box Assembly Complete(includes illus. nos. 4 through 12)Twin Speed Nut#10-16 x 1/2” Hex Head TEK Crimptite ScrewSail Switch Box Cover and Bracket ONLYSail Switch ONLY#4 x 3/4” Pan Head “A” Machine ScrewSail Switch Actuator RodSail Switch Damper (flat)1/8” Push On Fastener#10-16 x 1/2” Hex Washer TEK ScrewElectric Oven Front Cover ONLYLarge Relay Box Cover ONLY#8-18 x 7/16” Phillips Pan Head TEK Screw290 Hi-Limit#10-16 x 1/2” Hex Washer TEK Screw#10-24 Speed NutTerminal Lug for 110-8 Wire1/4-20 Free Spin Wash NutOven RelayOven Relay Replacement CoilInternal Ceramic Insulator (2 per element)External Ceramic Insulator (2 per element)#10-32 Hex Nut (4 per element)Bus BarOven Wire#10 Star Washer (2 per element)Large Electric Oven Right Side Cover ONLY#10-24 x 5/8” Truss Head Machine ScrewSteam to Electric Interface Plate.Not Illustrated* Refer to Electric Oven Component Application Chart on page 35.** Consult factory for wiring harness required.*** Needed when converting from steam heat to electric heat.CONTINENTAL GIRBAU, INC.
28Illus. No.Sail Switch AssemblyPart iptionSail Switch Mounting BracketSail Switch Damper (flat)Sail Switch Box CoverSail Switch BoxTwin Speed Nut1/8” Push On Fastener#10-16 x 1/2” Hex Head TEK Crimptite Screw#4 x 3/4” Pan Head “A” Machine ScrewSail Switch ONLYSail Switch Box Assembly Complete(includes illus. nos. 1 through 10)Sail Switch Actuator RodCONTINENTAL GIRBAU, INC.
Single-Phase (1ø) Motor, Electric Relay Panel AssemblyIllus. No.123456789101112131415Part 2004121010153002132459121300111 or 2121111113Description#6-32 Pal Nut#10-16 x 1/2” Hex Washer TEK Screw#6-32 x 1-1/4” Phillips Pan Head Machine Screw2-Position Terminal BlockRear Electric Mounting Plate ONLYRear Electric Panel Assembly Complete - 120 Volt(includes illus. nos. 1 through 14)Rear Electric Panel Assembly Complete - 208-240 Volt(includes illus. nos. 1 through 14)Transformer Assembly - 120 VoltTransformer Assembly - 208-240 VoltFuse Holder ONLY3/4-Amp (slo blo) Fuse ONLY - 120 Volt1/2-Amp (slo blo) Fuse ONLY - 208-240 Volt#8-18 x 7/16” Phillips Pan Head TEK Screw#10 x 1/2” Hex Washer TEK Screw (green)5/16-18 Hex NutL-70 Ground Lug5/16” Lock Washer3-Pole ContactorOpen/Closed BushingCONTINENTAL GIRBAU, INC. 29
30Illus. No.1234567891011121314153-Phase (3ø) Motor, Electric Relay Panel AssemblyPart 121300111222111113Description#6-32 Pal Nut#10-16 x 1/2” Hex Washer TEK Screw#6-32 x 1-1/4” Phillips Pan Head Machine Screw4-Position Terminal Block (for models mfd. with 3ø motors)2-Position Terminal Block (for models mfd. with 1ø motors)Rear Electric Mounting Plate ONLYRear Electric Panel Assembly Complete - 208-240 VoltFor Gas and Steam Models ONLY(includes illus. nos. 1 through 14)Rear Electric Panel Assembly - 208-240 VoltFor Electric Heated Models ONLY(includes illus. nos. 1 through 14)Rear Electric Panel Assembly Complete - 380-416 Volt(includes illus. nos. 1 through 14)Rear Electric Panel Assembly Complete - 208-240 VoltFor Electric Heated Models ONLYFor Models Mfd. with Single-Phase (1ø) Motor ONLY(includes illus. nos. 1 through 14)Rear Electric Panel Assembly Complete - 380-416 Volt(includes illus. nos. 1 through 14)For Electric Heated Models ONLYFor Models Mfd. with Single-Phase (1ø) Motor ONLYTransformer Assembly - 208-240 Volt for Gas and Steam Models ONLYTransformer Assembly - 208-240 Volt for Electric Heated Models ONLYTransformer Assembly - 380-416 VoltFuse Holder ONLY1/2-Amp (slo blo) Fuse ONLY - 208-240 Volt#8-18 x 7/16” Phillips Pan Head TEK Screw#10 x 1/2” Hex Washer TEK Screw (green)5/16-18 Hex NutL-70 Ground Lug5/16” Lock Washer3-Pole ContactorOpen/Closed BushingCONTINENTAL GIRBAU, INC.
460-480 VAC 3-Phase (3Ø) Motor, Electric Relay Panel AssemblyIllus. No.12345678910111213141516Part ion#6-32 x 1-1/2” Phillips Pan Head Machine Screw4-Position Terminal BlockTransformer Assembly (460 VAC) for Micro Models ONLYTransformer Assembly (460 VAC) for Non-Micro Models ONLY1-Amp Double-Pole Circuit Breaker (460 VAC Only)35 x 15mm Din Rail#8-18 x 7/16” Phillips Pan Head TEK Screw#10 x 1/2” Ground Screw5/16-18 Hex NutL-70 Ground Lug5/16” Lock Washer24 VAC 3-Pole ContactorMounting Plate ON
CONTINENTAL GIRBAU, INC. Main Door Switch Assembly Illus. No. Part No. Qty. Description 1 150006 2 #6-32 x 7/8" Phillips Pan Head Machine Screw 2 152013 2 #6-32 Hex Nut 3 153010 2 #6 Star Washer 4 137005 1 Door Switch 5 122636 2 Flag Terminal 6 881213 1 White Main Door Switch Housing ONLY 881216 1 White Main Door Switch Housing Complete
