Transcription
ALGO8028 SIP Doorphone (FW 2.7.4)8028 SIP DoorphoneFW Version 2.7.4Installation & ConfigurationOrder Codes8028Document 90-00054F2017-09-19Page 1SIP DoorphoneAlgo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Table of ContentsIMPORTANT SAFETY INFORMATION . 5ABOUT THE ALGO 8028 SIP DOORPHONE . 6GETTING STARTED - QUICK INSTALL & TEST . 7APPLICATIONS . 8TYPICAL APPLICATIONS FOR AUXILIARY INPUTS AND OUTPUTS . 8Cancel Ring When Door Opened . 8Trigger Door Bell from Door Station . 8Trigger Door Station from External Button/Event . 8Cancel Door Open Relay once Door Opened . 8Unlock Door Indefinitely until Canceled . 9Anti-Door Tamper . 9In-User and Ring. 9INSTALLATION . 10DOOR STATION INSTALLATION . 11DOOR OR GATE CONTROL BASICS . 12DOOR RELEASE . 12Fail Locked / Fail Secure Electric Strike . 12Fail Unlocked / Fail Safe Electric Strike. 12Power Supply. 13PRE-WIRING INSTRUCTIONS . 13WIRING CONNECTIONS . 14AUXILIARY DRY CONTACT OUTPUTS . 15AUXILIARY DRY CONTACT INPUTS . 15RED LED INDICATORS . 16POWER . 16TELEPHONE . 16DOOR STATION . 16UNLOCK . 16WEB INTERFACE . 17WEB INTERFACE LOGIN . 18STATUS . 18BASIC SETTINGS TAB – SIP. 19SIP DOMAIN (PROXY SERVER) . 19EXTENSION . 19AUTHENTICATION ID . 19AUTHENTICATION PASSWORD. 20DIALING EXTENSIONS . 20BASIC SETTINGS TAB - AUDIO . 21SPEAKER VOLUME . 21Document 90-00054F2017-09-19Page 2Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)MICROPHONE VOLUME . 21RINGBACK TONE . 21BASIC SETTINGS TAB – DOOR RELAY . 22MOMENTARY OPEN CODE . 22DURATION . 22CANCEL IF DOOR OPENED . 22LATCH OPEN CODE . 23LATCH CLOSED CODE . 23DTMF DETECTION TYPE . 23DOOR UNLOCK TONE . 23ALLOW NETWORK CONTROL . 23ADVANCED SETTINGS TAB - NETWORK . 24PROTOCOL . 24VLAN MODE . 24VLAN ID . 25VLAN PRIORITY . 25DIFFERENTIATED SERVICES (6-BIT DSCP VALUE) . 25ADVANCED SETTINGS TAB – ADMIN . 26PASSWORD. 26CONFIRMATION . 26DEVICE NAME . 26INTRODUCTION SECTION ON STATUS PAGE . 27WEB INTERFACE SESSION TIMEOUT . 27LOG LEVEL . 27LOG SIZE . 27LOG METHOD . 27LOG SERVER . 27HARDWARE WATCHDOG . 27SNMP SUPPORT (V1 GET ONLY) . 27ADVANCED SETTINGS TAB – TIME. 28TIME ZONE . 28NTP TIME SERVER . 28ADVANCED SETTINGS TAB – PROVISIONING . 29MD5 CHECKSUM . 30GENERATING A GENERIC CONFIGURATION FILE . 30GENERATING A SPECIFIC CONFIGURATION FILE . 31ADVANCED SETTINGS TAB – CALL . 32ANSWER INBOUND CALL. 32ANSWER TONE . 32OUTBOUND RING LIMIT . 32CANCEL IF DOOR OPENED . 33ALLOW CALL BUTTON TO END OUTBOUND CALL . 33MAXIMUM CALL DURATION . 33Document 90-00054F2017-09-19Page 3Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)ADVANCED SETTINGS TAB – AUXILIARY I/O . 34CONTROLLER OUTPUT . 34DOOR STATION OUTPUT. 34IN-USE DEFINITION . 35CONTROLLER INPUT . 35DOOR STATION INPUT. 35ADVANCED SETTINGS TAB – SECURITY . 36MAX DOOR OPEN. 36DOOR OPEN ALARM . 36DOOR STATION DISCONNECTED . 36ADVANCED SETTINGS TAB – ADVANCED SIP . 37OUTBOUND PROXY . 37STUN SERVER . 37REGISTER/SUBSCRIBE PERIOD (SECONDS) . 37KEEP-ALIVE METHOD . 37SERVER REDUNDANCY FEATURE . 38BACKUP SERVER #1 . 38BACKUP SERVER #2 . 38POLLING INTERVALS (SECONDS). 38POLL ACTIVE SERVER . 38AUTOMATIC FAILBACK . 38POLLING METHOD . 38SYSTEM TAB - MAINTENANCE . 39DOWNLOAD CONFIGURATION FILE . 39RESTORE CONFIGURATION FILE . 39RESTORE CONFIGURATION TO DEFAULTS . 39REBOOT THE DEVICE . 39METHOD. 39FIRMWARE IMAGE . 40MD5 CHECKSUM . 40SYSTEM TAB - NETWORK LOGGING . 40SPECIFICATIONS . 41FCC COMPLIANCE STATEMENT . 44Document 90-00054F2017-09-19Page 4Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Important Safety InformationThe 8028 SIP Doorphone is designed and tested to comply with EN 609501:2006 safety requirements.INSTALLATIONWhen the Doorphone Controller is connected to wiring that exits thebuilding, there is potential risk of lightning induced electrical surges or highvoltages from fault conditions. To reduce risk, outdoor wiring should beprotected by Earth grounded conduit whenever possible.If outdoor wiring will be connected to the Doorphone Controller then thepower supply provided with the Doorphone Controller must first beconnected to a properly Earth grounded mains supply. Under nocircumstances can the Doorphone Controller be disconnected from Earthground while connected to outdoor wiring.EMERGENCY COMMUNICATIONIf used in an emergency communication application, the 8028 SIPDoorphone should be routinely tested. SNMP supervision isrecommended for assurance of proper operation.Document 90-00054F2017-09-19Page 5Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)About the Algo 8028 SIP DoorphoneIdeal for secure business entrances, emergency intercom, andresidential gates, Algo’s 8028 SIP Doorphone provides hands-freeintercom capability, entrance security with door unlock control,rugged weatherproof design, and superior audio performance.Fully compatible with SIP industry standards, the 8028 SIPDoorphone will work with most hosted or enterprise SIP-basedservers supporting third-party SIP endpoints.The 8028 Doorphone includes a Control Unit, Door Station, andPower Supply. The Control Unit and Door Station can be connectedwith a single twisted pair wire up to 1,000 feet (300 m) with theDoor Station located outdoors and the Control Unit in a dry indoorlocation.What is Included 8028 Digital Door Station & ControllerPower SupplyStainless Steel & Brass Faceplates6ft (2m) Network CableWhat is not Included Document 90-00054F2017-09-19Page 6Physical Door SensorDoor StrikeDoor Strike Power SupplyThis Installation Guide (www.algosolutions.com/8028/guide)Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Getting Started - Quick Install & TestThis guide provides important safety information which should beread thoroughly before permanently installing the device.1. Connect the power supply to thePower Jack of the Doorphone Controllerand plug into an available AC outlet.2. Flush or surface-mount the Digital DoorStation at desired location and connect atwisted telephone wire pair between the“CTRL” terminals of the Door Station andthe center pair (red and green) of thesupplied Telephone Wiring Jack. Polarity isnot important.3. Using the short six conductor modularcable, connect the Telephone Wiring Jackto the Door Station Jack of the Doorphone Controller.4. Using an Ethernet cable, connect the Ethernet Jack of the DoorphoneController to your LAN.5. Press the call button on the Door Station. A recorded voice will speakthe IP Address of the device. (Once the SIP Server field is populatedin the 8028 web interface (Step 7), the call button will contact thepreconfigured extension when pressed.) The IP address may also bediscovered by downloading the Algo locator tool to find Algo deviceson your network: www.algosolutions.com/locator6. Access the 8028 web interface by entering the IP address into abrowser (Chrome, IE, Firefox, etc.) and login usin the defaultpassword algo.7. Use the Web Interface to enter the SIP Proxy Server address underthe BASIC SETTINGS SIP tab.8. Enter the SIP Extension, Authentication ID, and Password. Also,enter the target Dialing Extension that the Door Station will call.Document 90-00054F2017-09-19Page 7Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)9. Press the call button on the Door Station, then answer tocommunicate with the Door Station. Press the digit 6 on the phonekeypad to activate the door control relay for three seconds (ifapplicable).ApplicationsTypical Applications for Auxiliary Inputs and OutputsThe 8028 architecture and digital link between the Door Station andController provides flexible options using the auxiliary inputs and outputs.These are some typical applications.Cancel Ring When Door OpenedIn a residential or warehouse installation it is not uncommon for the doorto be answered in person before the phone is answered. Either DoorStation or Control Unit inputs can be configured to cancel ring if the dooris opened before a call is answered. This requires a normally closed ornormally open contact to detect door open.Trigger Door Bell from Door StationWhen the Door Station call button is pressed, either (or both) the DoorStation or Control Unit dry contact output can be configured to activate adoor bell or auxiliary alerting system in addition to phone ring.Trigger Door Station from External Button/EventEither the Control Unit or Door Station can accept a dry contact closure toactivate the Doorphone as if the call button had been pressed. This couldbe an external doorbell button, PIR detector, or some other system.Cancel Door Open Relay once Door OpenedThe door opening control can be set for activation (using the ‘Open Code’)up to 30 seconds (set by the ‘Relay Time’ setting) to allow sufficient timefor entry. For security, the 8028 Doorphone can be configured to cancelDoor Opening once the door is opened to prevent “tailgating” byunauthorized personnel.Document 90-00054F2017-09-19Page 8Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Unlock Door Indefinitely until CanceledThe door opening control can be set to unlock indefinitely (using the‘Latch Open Code’) until canceled (using the ‘Release Code’) that locks itagain. This allows an entrance to be used repeatedly for a period of timewithout requiring multiple activations of the door control relay.Anti-Door TamperA feature of the 8028 Doorphone is to ring the telephone(s) with awarning alert in the event a door is ajar due to tampering (such as adoor blocked open after being legitimately released for a visitor).In-User and RingEither the Control Unit or Door Station can be configured to provide a drycontact output during ring or in-use for channel selection (typically) ofthird party video monitoring systems.Document 90-00054F2017-09-19Page 9Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)InstallationDocument 90-00054F2017-09-19Page 10Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Door Station InstallationThe Door Station, provided with the 8028 Doorphone kit, is weatherprotected for outdoor installation. However if network cablingextends beyond the perimeter of the building then adequate lightningprotection is required to protect the cabling and network switch fromlightning surges. No lightning protection is required by UL or CSA ifthe Door Station is located on the outside wall of a building and thewiring is inside the perimeter of the building.1. Remove the Door Station faceplate2. Determine if you want a flush or surface mount installationFor surface mount:ooooDiscard the smaller flushmount gasket.Verify the correct orientationof the surface mount gasket.Thread the wires through thecenter hole, then through thesurface mount bracket.Fasten the surface mountbracket at the desiredlocation on the wallFor flush mount:(Using a dual gang electrical boxembedded in the wall)ooDocument 90-00054F2017-09-19Page 11Discard the larger surfacemount gasket and bracket.Slide the flush mount gasketonto the main housingassembly.Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Door or Gate Control BasicsControl contacts are provided from the Doorphone Controller and aretypically used for door strike activation or gate control. For security,the door control relay is located in the Controller to avoid entry bytampering.Door ReleaseDoor release typically involves energizing or de-energizing a doorstrike which pivots to allow a locked door to open without retractionof the latch bolt. There are two different types of door strikes: “Fail Locked” (or “Fail Secure”) “Fail Unlocked” (or “Fail Safe”)Fail Locked / Fail Secure Electric StrikeThese require power to release andremain locked during power failure. Thedoor may still normally be opened fromthe outside with a key, or from insidewithout a key. The door control relay isused to apply power to release the door.Fail Unlocked / Fail Safe ElectricStrikeThese (as well as magnetic locks), requirepower to lock and become unlockedduring power failure. The door controlrelay is used to maintain power to thedoor lock (NC and C contacts) which isinterrupted to release the door. Magneticlocks may require override systems toallow safety exit in the event of fire.Document 90-00054F2017-09-19Page 12Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Power SupplyThe Doorphone Controller provides an auxiliary 24 V 0.3 A powersupply which is suitable for common types of door strikes. If morecurrent or a different voltage is required, then the customer mustprovide a matching power supply for the electric strike or magneticlock. Maximum switching capability of the 8028 door control contactsis 1 A 30 V.The Door Control relay may also be configured for alternatefunctionality including In-Use, Ring, and Call Button Press.Pre-Wiring InstructionsPlease visit www.algosolutions.com/doorstrike for more information.Document 90-00054F2017-09-19Page 13Algo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Wiring ConnectionsDoor Control5 PositionRemovableTerminal BlockRelayOptionalAuxiliaryPowerDoor StationJackRJ12 TelephoneJackEthernetJackNONormally OpenCCommonNCNormally CloserPWR -0.3A (GND)PWR 0.3A (24V)2 V 0.3A4Center Pair(Red & Green)Door StationSecond Pair(Yellow & Black)Dry Contract InputMax 1kOhmOutside Pair(Blue & White)Dry Contract OutputMax 50mA 30VConnect to LAN with access to SIP-compliantProxy Server.RJ45 JackResetButtonTo return all settings to a factory default, pressand hold the reset button at start up. Continue tohold the button until all LEDs start to flash.Door Station6 PositionTerminal BlockCTRLINOUTDocument 90-00054F2017-09-19Page 14RESETConnect to Door Station Jack ofDoorphone ControllerDry Contact Input to Door Station(e.g. Door Contact, Doorbell Switch);Max 1kOhmDry Contract Output from DoorStation (e.g. Gate Control);Max 50mA 30VAlgo Communication Products Ltd4500 Beedie St Burnaby BC Canada V5J 5L2www.algosolutions.com(604) 454-3792support@algosolutions.com
ALGO8028 SIP Doorphone (FW 2.7.4)Auxiliary Dry Contact OutputsBoth the Doorphone Controller and Door Station provide a drycontact output for connection to auxiliary devices. Maximumswitching capacity is 30 V 50 mA.This output contains an internal opto-coupler, not a true relay, so itwill incur a voltage drop of about 2V.Default operations are as follows: Doorphone Controller Output In-Use (commonly used forcamera control)Door Station Output Call Button Press (commonly used toactivate a secondary doorbell)Other options for Doorphone Controller output include Ring and CallButton Press. Other options for Door Station output include In-Useand Door Control.Auxiliary Dry Contact InputsBoth the Doorphone Controller and Door Station can detect a drycontact closure from auxiliary devices. A non-capacitive and noninductive low voltage and low current is used to detect contactclosure.Default operations are as follows: Doorphone Controller input Door Sensor Normally Closed (usedto detect door open)Door Station input Call Button Normally Open (used to detectexternal doorbell switch)Options for Doorphone Controller input include Door Sensor NormallyClosed, Door Sensor Normally Open, Manua
ALGO 8028 SIP Doorphone (FW 2.7.4) Document 90-00054F Algo Communication Products Ltd (604) 454-3792 2017-09-19 4500 Beedie St Burnaby BC Canada V5J 5L2 support@algosolutions.com Page 6 www.algosolutions.com About the Algo 8028 SIP Doorphone Ideal for secure business entrances, emergency intercom, and
