Transcription
The Ideal Insulation SolutionPRODEX TOTAL INSULATIONOur products:PRODEX AD5 THERMALINSULATIONPRODEX AD10 THERMALINSULATIONNEW
The Ideal Insulation SolutionPRODEX TOTAL INSULATIONProduct Characteristics:Reflects 97% of the radiant heatRepels the heat in warm climateRetains heat in cold areasAllows obtaining energetic saving up to 55%with the use of air-conditioningReduces noise from the falling rainProduct of 100% close cell what allows to be:impermeable, hygienic, and resistant toagro-chemicals, acids, bases, oils and coveringsEnvironmental Characteristics:Our products are free from toxic gasWe do not harm the ozone layerAll product are environmental frendlyDo no develop allegiesWe are members of the united green building CouncilOur packing is made with
The Ideal Insulation SolutionNEWPRODEX AD5 THERMALINSULATIONRadiant barrier, Thermalbreak and Vapor BarrierThis insulation product reduces heatingand cooling costs. Reflective aluminumfoil on each side of a 5mm closed-cellpolyethylene foam center. Ideal for hotand cold climates.INSULATION LAYERSAluminium Foilpolyethylene backingClosed-cell Polyethylene foampolyethylene backingAluminium FoilPRODEX AD10 THERMALINSULATIONIncrese R Value, addlongitudinal strength, getbetter installation finish withour new thermal meld system.This insulation product reduces heatingand cooling costs. Reflective aluminumfoil on each side of a 10mm closed-cellpolyethylene foam center. Ideal for hotand cold climates.INSULATION LAYERSAluminium Foilpolyethylene backingClosed-cell Polyethylene foampolyethylene backingAluminium Foil5 mmAD5Nominal Thickness:5mm ( or – 0.5 mm)10 mmAD10Nominal Thickness:10mm ( or – 0.5 mm)
The Ideal Insulation SolutionPRODEX AD5 THERMAL INSULATIONTechnical specifications1-PRODUCTINSULATOR AD (double aluminium face - barrier against fire)2. MEASUREMENTS AND TOLERANCES OF THE STANDARD PRODUCTTHICKNESS 5 0.35 (mm)LENGHT 30 cmWIDTH: 1.22 0.01 (m)3. CHARACTERISTICS OF THE PRODUCTVALUECHARACTERISTICSSTRUCTURE OF THE FOAM CELLClosedAVERAGE WEICHT OF M20,242kg/m²DENSITY OF THE INSULATOR20-30 kg/m3PERMEABILITYImpermeablePERMEABILITY TO THE WATER STEAM0.033 g/m2hkPa - 0.05 perms (gr/ft²*h*in.hg)FLAME RATE0SMOKE DEVELOPMENT15EMITTANCE0.03RESISTANCE TO FUNGUSResistant / Does not promote the growth of fungus – moldDELAMINATIONDoes not delaminateOPERATION TEMPERATURE- 20ºc / 80ºcTHERMIC RESISTANCE (factor R, hent flor down)15.67 ft2h f/BtuBARK ADHESION (fast action)1,33-1,31 kg/inchTOTAL THICKNESS OF FAST ACTION0,095 mmADHESION CAPACITY (fast action)24 hr/in²INITIAL STICKING LENGHT (fast action)1,5 cm NORMASTM 1622Dir. UEAtcASTM E 96/IRAM 1735ASTM E-84ASTM E-84ASTM C-1371-98ASTM C 1338ASTM C-1224-99ASTM C-1258ASTM C-236ASTM D-1000ASTM D-1000PSTC-7PSTC-6PRODEX AD10 THERMAL INSULATIONTechnical specifications1-PRODUCTINSULATOR AD (double aluminium face - barrier against fire)2. MEASUREMENTS AND TOLERANCES OF THE STANDARD PRODUCTTHICKNESS 10 0.70 (mm)LENGHT 30 cmWIDTH: 1.22 0.01 (m)3. CHARACTERISTICS OF THE PRODUCTVALUECHARACTERISTICSSTRUCTURE OF THE FOAM CELLClosedAVERAGE WEICHT OF M20,242kg/m²DENSITY OF THE INSULATOR20-30 kg/m3PERMEABILITYImpermeablePERMEABILITY TO THE WATER STEAM0.033 g/m2hkPa - 0.05 perms (gr/ft²*h*in.hg)FLAME RATE0SMOKE DEVELOPMENT15EMITTANCE0.03RESISTANCE TO FUNGUSResistant / Does not promote the growth of fungus – moldDELAMINATIONDoes not delaminateOPERATION TEMPERATURE- 20ºc / 80ºcTHERMIC RESISTANCE (factor R, hent flor down)21.36 ft2h f/BtuBARK ADHESION (fast action)1,33-1,31 kg/inchTOTAL THICKNESS OF FAST ACTION0,095 mmADHESION CAPACITY (fast action)24 hr/in²INITIAL STICKING LENGHT (fast action)1,5 cm NORMASTM 1622Dir. UEAtcASTM E 96/IRAM 1735ASTM E-84ASTM E-84ASTM C-1371-98ASTM C 1338ASTM C-1224-99ASTM C-1258ASTM C-236ASTM D-1000ASTM D-1000PSTC-7PSTC-6
The Ideal Insulation SolutionOur reflective insulations are used in:Homes,Metal buildings,Pole barnsCommercial buildingsApplications uctworkUnder-concrete.Prodex Total is the recommended product for theseapplications. It represents 81% of our sales, receives thehighest customer reviews and most stringent testing.
The Ideal Insulation SolutionPRODEX AD10 THERMAL INSULATIONBEST METAL BUILDING INSULATION!The AD10 insulation is our higher quality product,It allows you to get the best installation lookImprove the tearing resistanceGet a constant R ValueReduce condensation riskThermal weld overlapMAIN ADDED VALUES1.THERMAL WELDING METHOD2.VAPOR BARRIER3.ONE LAYER R VALUES AT DIFERENT TEMPERATURES4.RESISTANCE TO GROWD OF FUNGINEW
The Ideal Insulation Solution1.Thermal Welding MethodProdex AD 10 material has cuts at the edge to overlap therolls, a hot air gun is apply this melts the polyethylene foamat both rolls, then a little hand pressure is require tocomplete the welding process.Thermal welding allows Prodex AD 10 to get a totallyimpermeable overlapping and mechanical seal betweeninstalled rolls
The Ideal Insulation Solution1.Thermal Welding MethodProdex AD 10 material has cuts at the edge to overlap therolls, a hot air gun is apply this melts the polyethylene foamat both rolls, then a little hand pressure is require tocomplete the welding process.Thermal welding allows Prodex AD 10 to get a totallyimpermeable overlapping and mechanical seal betweeninstalled rolls
The Ideal Insulation Solution3. One layer R Values at diferent temperaturesR value AD 10Air chamber (in)Rafter tem ( F)ft2 h 1767521.360017610020.660017612519.9600176Foam R value ft2 h F/BtuFoam thickness (mm)3.5101.7600176
The Ideal Insulation Solution4. Resistance to growd of fungiProdex reflective insulation has been tested for resistance tothe growd of fungi in accordance with the ASTM C 1338.Against all the followin fungal spices:Asperillus nigerAspergillus flavus.Aspergillus versicolor.Penicillium funiculosum.Chaetomium globosum.
The Ideal Insulation SolutionPRODEX AD10 THERMAL INSULATIONInstallationNEWABOVE RAFTERS INSTALLATIONSet the Prodex AD 10 at the eaves andunroll parallel to the eaves.As the Prodex AD 10 is unrolled acrossrafters fixit using nails or staples of at least½ “ length.The next roll must overlap the precedinglayer by using our Thermal welding systemthis will guide the roll and seal the overlapalong the entire length.Prodex Ad 10 should be permanently fixedin place by using wooden battens parallel tothe rafters, held in place with nails.When the top layer has been battened, anyexcess material may be cut by running asharp knife along the edge of the batten.As soon the Prodex AD 10 is set and tight,roof installation can take place as a normalprocedure.
The Ideal Insulation SolutionPRODEX AD10 THERMAL INSULATIONINSTALLATION METHOD R 22Roof coverBattensAir chamber2.6”AD10RafterINSTALLATION METHOD R 30BattensRoof coverAd10Ad10SoffitAir chamber #2Air chamber #1NEW
The Ideal Insulation SolutionPRODEX TOTAL INSULATIONBUILDINGENUCONCILENVIROMENTAL MANAGEMENT SYSTEMS CERTIFICATIONU.S.GREBest InsulationLowest PriceFastest DeliveryUSGBC
PRODEX AD5 THERMAL INSULATION PRODEX AD10 THERMAL INSULATION Increse R Value, add longitudinal strength, get better installation šnish with our new thermal File Size: 2MBPage Count: 13
