WIXLIB

ACRYLIC HIGH-BAYFEATURESr Slide-on, die-cast aluminum mounting box with opening for 3/4" conduitr Heavy-duty, steel housing with open-air ballast for cooler operationr Standard white polyester, powder-paint finishr High power factor ballast with class H insulationr Minimum temperature: -40 C (-40 F) HPS; -30 C (-20 F) MH and MPr Mogul-base porcelain socketr Acrylic refractor system provides even illuminationOpen BottomPD2524-1/4" [616mm]PD2224" [607mm]Drop BottomAcrylicDB2527-3/8" [695mm]Compliances may not apply to all product configurations. Please consult the product spec sheet for compliance details.COMPLIANCES: UL Listed - Damp Location, CSA Listed, 55 C Ambient Temperature Rating,65 C Ambient Temperature Rating, EISA CompliantDB2226-1/2" [673mm]LX DIRECT-MOUNTPRISMATICSTEELER22" AND 25"22" [559mm]25" [636mm]ORDERING INFORMATIONSAMPLE NUMBER: MPLX-DB22-320-MT-ORLamp TypeSeriesRefractor TypeRefractor DiameterLamp WattageHP High PressureSodiumMH Metal Halide 1,2MP Pulse StartMetal Halide 1LX PrismaticDirect MountBenchmarkDB PrismaticAcrylic withDrop AcrylicRefractorPD PrismaticAcrylic22 22" Diameter25 25" DiameterHP70 70W100 100W150 150W250 250W400 400WMH 2175 175W250 250W400 400WMP175 175W200 200W250 250W320 320W350 350W400 400WVoltageSocket120V 120V208V 208V240V 240V277V 277V347V 347V480V 480VMT Multi-Tap wired 277VTT Triple-Tap wired 347V5T 5-Tap[Blank] Non Applicable (HPSor not compatible withOR socket)OR Open Rated Socket forMetal HalideOptions (Add as Suffix) 3C3 3' Cord without Plug (Specify voltage)EM Quartz Restrike with "Delay Relay" (Quartz lamp strikes at both hot and cold starts)EM/SC Emergency Separate CircuitF1 Single Fuse (120, 277 or 347V only)F2 Double Fuse (208, 240 or 480V only)FH-1 Die-cast Aluminum Fixture Hook (With 3/4" threads for easy installation)FL-1 Malleable Iron Plated Fixture Loop (With 3/4" threads for easy installation)HC LumaWatt Fixture Control Module (Low voltage leads pulled out of top connection box for areasrequiring all wiring to be installed in conduit)HL LumaWatt Fixture Control Module (Allows low voltage control wire to be daisy-chained betweenfixtures outside AC conduit run similar to low voltage intercoms, fire alarms and phone systems)HSW Integral LumaWatt Sensor and Control with Wide DistributionL/TCB Less Top Connector Box (Housing shipped less top connector box. Specify when usingTWMBS accessory)LL Lamp IncludedPC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Cord and Plug - 18" Power Cord and Non-NEMA Plug Configuration (Must be used withFL-1 and TPPH. Must specify single voltage)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)Q Quartz Restrike (Hot strike only)QD Quick Disconnect Die-cast Pendant Mount Box (Specify single voltage. Not compatible with PC3,PHC, C3, MWS, RM or HC)QLL Quartz Lamp Included (Lamp is Cooper designated product based on luminaire requirements.Lamp is shipped separate from luminaire unless otherwise noted)SCF 3' Aircraft Safety Cable Secures Housing to Ceiling (Alternative lengths available. Example: SCF6 6' cable)SHK Die-cast Aluminum Fixture Hook (With safety screw and 3/4" threads for easy installation)SS Space Saver FeatureW/MWS MWS Industrial Components (Attached to the fixture at the factory. Standard cord length is 3foot; 6 foot and 11 foot also available. Please refer to MWS Modular Wiring System sectionfor additional information)Accessories (Order Separately)C3 3' Cord without Plug (Requires FH-1, FL-1 or SHK)FH-1 Fixture HookFL-1 Fixture LoopFWG22/WDB Full Wire Guard for use with PD22 and DB22 Drop Lens (DB22 not included)FWG22/WG22 Full Wire Guard for PD22 (SGB not included)FWG22/WG22/SGB22A Full Wire Guard for 22" Refractor and SGB22 Lens (Maximum 400W)FWG25/WDB Full Wire Guard for use with PD25 and DB25 Drop Lens (DB25 not included)FWG25/WG25 Full Wire Guard for PD25 (SGB not included)FWG25/WG25/SBG25A Full Wire Guard for 25" Refractor and SGB25 Lens (Maximum 400W)MBT Twin Mount Bracket (Fixtures must be same voltage and without hooks, loops or plugs)PC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Hook Cord and Non-NEMA Plug Configuration (Must be used with FL-1 and TPPH)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)SGB22A Safety Glass Bottom for PD22 Refractor (Not compatible with WG22. Maximum 400W)SGB25A Safety Glass Bottom for PD25 Refractor (Not compatible with WG25. Maximum 400W)SHK Hook with Safety ScrewTPPH Thruway Pendant Power Hook (Requires FL-1 and PHC. Specify voltage)TPPH-F Thruway Pendant Power Hook Single Fuse (Requires FL-1 and PHC. Specify voltage 120,277 or 347V)TPPH-F-QD Thruway Pendant Power Hook Single Fuse, Quick Disconnect (Requires FL-1 and PHC.Specify voltage 120, 277 or 347V)TPPH-F2 Thruway Pendant Power Hook Double Fuse (Requires FL-1 and PHC. Specify voltage 208,240 or 480V)TPPH-F2-QD Thruway Pendant Power Hook Double Fuse, Quick Disconnect (Requires FL-1 andPHC. Specify voltage 208, 240 or 480V)TPPH-NEMA Thruway Pendant Power Hook (Requires FL-1 and PHC-XXXV-NEMA. Specify voltage)TWMBS Thruway Mounting BoxWG22 Wire Guard for PD22 Refractor (Not compatible with SGB)WG22/SGB22A Gym Wire Guard with Safety Glass Bottom for PD22 Refractor (Maximum 400W)WG25 Wire Guard for PD25 Refractor (Not compatible with SGB)WG25/SGB25A Gym Wire Guard with Safety Glass Bottom for 25" RefractorWGD22 Wire Guard for DB22 RefractorWGD25 Wire Guard for DB25 RefractorNOTES: 1. Open Rated (OR) socket and lamp must be used. 2. Metal halide available in non-U.S. markets only. 3. Not all options and configurations are compatible and restrictions may apply. Reference specification sheetfor additional details.LUMARKSpecifications and dimensions subject to change without notice. Consult your Cooper Lighting Representative or visit www.cooperlighting.com for available options, accessories and ordering information.Cooper Lighting by Eaton Product Selection Guide Sixth Edition www.cooperlighting.com15-6

ACRYLIC HIGH-BAYFEATURESr Slide-on, die-cast aluminum mounting box with opening for 3/4" conduitr Heavy-duty, steel housing with open-air ballast for cooler operationr Standard white polyester, powder-paint finishr High power factor ballast with class H insulationr Minimum temperature: -40 C (-40 F) HPS; -30 C (-20 F) MH and MPr Staggered mounting bosses for eight-position socket adjustmentr Available drop bottom acrylic lens or glass bottom lensr Enclosed and gasketed at door, refractor, neck and housingr Clear, tempered glass or prismatic acrylic drop lensENPD2228-3/4" [730mm]Drop BottomAdds 3-1/2" [89mm]to Overall HeightCompliances may not apply to all product configurations. Please consult the product spec sheet for compliance details.SE E&G PRISMATICACRYLIC STEELER22"COMPLIANCES: UL Listed, CSA Listed - Damp Location, 55 C Ambient Temperature Rating,65 C Ambient Temperature Rating, EISA Compliant22" [559mm]ORDERING INFORMATIONSAMPLE NUMBER: MPSE-ENPD22-M-320-MT-ORLamp TypeSeriesRefractor TypeRefractor DiameterDistributionLamp WattageVoltageSocketHP High PressureSodiumMH Metal Halide 1,2MP Pulse StartMetal Halide 1SE Enclosed andGasketed SteelerENPD Enclosed andGasketedPrismaticAcrylicRefractor22 22" DiameterC ConcentratedM MediumW WideHP250 250W400 400W120V 120V208V 208V240V 240V277V 277V347V 347V480V 480VMT Multi-Tap wired 277VTT Triple-Tap wired 347V5T 5-Tap[Blank] Non Applicable(HPS or notcompatible withOR socket)OR Open Rated Socketfor Metal HalideMH 2175 175W250 250W400 400WMP175 175W200 200W250 250W320 320W350 350W400 400WOptions (Add as Suffix) 3C3 3' Cord without Plug (Specify voltage)EM Quartz Restrike with "Delay Relay" (Quartz lamp strikes at both hot and cold starts)EM/SC Emergency Separate CircuitF1 Single Fuse (120, 277 or 347V only)F2 Double Fuse (208, 240 or 480V only)FH-1 Die-cast Aluminum Fixture Hook (With 3/4" threads for easy installation)FL-1 Malleable Iron Plated Fixture Loop (With 3/4" threads for easy installation)HC LumaWatt Fixture Control Module (Low voltage leads pulled out of top connection box for areasrequiring all wiring to be installed in conduit)HL LumaWatt Fixture Control Module (Allows low voltage control wire to be daisy-chained betweenfixtures outside AC conduit run similar to low voltage intercoms, fire alarms and phone systems)HSW Integral LumaWatt Sensor and Control with Wide DistributionL/TCB Less Top Connector Box (Housing shipped less top connector box. Specify when usingTWMBS accessory)LL Lamp IncludedP Pre-set Socket Position from the FactoryPC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Cord and Plug - 18" Power Cord and Non-NEMA Plug Configuration (Must be used withFL-1 and TPPH. Must specify single voltage)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)Q Quartz Restrike (Hot strike only)QD Quick Disconnect Die-cast Pendant Mount Box (Specify single voltage. Not compatible with PC3,PHC, C3, MWS, RM or HC)QLL Quartz Lamp Included (Lamp is Cooper designated product based on luminaire requirements.Lamp is shipped separate from luminaire unless otherwise noted)RM Remote MountSCF 3' Aircraft Safety Cable Secures Housing to Ceiling (Alternative lengths available. Example: SCF6 6' cable)SCR Aircraft Safety Cable-Housing to Reflector or RefractorSHK Die-cast Aluminum Fixture Hook (With safety screw and 3/4" threads for easy installation)SS Space Saver FeatureW/MWS MWS Industrial Components (Attached to the fixture at the factory. Standard cord length is 3foot; 6 foot and 11 foot also available. Please refer to MWS Modular Wiring System sectionfor additional information)Accessories (Order Separately)C3 3' Cord without Plug (Requires FH-1, FL-1 or SHK)FH-1 Fixture HookFL-1 Fixture LoopFWG22/WG22/SGB22A Full Wire Guard for 22" Refractor and SGB22 Lens (Maximum 400W)MBT Twin Mount Bracket (Fixtures must be same voltage and without hooks, loops or plugs)PC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Hook Cord and Non-NEMA Plug Configuration (Must be used with FL-1 and TPPH)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)SGB22A Safety Glass Bottom for PD22 Refractor (Not compatible with WG22. Maximum 400W)SHK Hook with Safety ScrewTPPH Thruway Pendant Power Hook (Requires FL-1 and PHC. Specify voltage)TPPH-F Thruway Pendant Power Hook Single Fuse (Requires FL-1 and PHC. Specify voltage 120,277 or 347V)TPPH-F-QD Thruway Pendant Power Hook Single Fuse, Quick Disconnect (Requires FL-1 and PHC.Specify voltage 120, 277 or 347V)TPPH-F2 Thruway Pendant Power Hook Double Fuse (Requires FL-1 and PHC. Specify voltage 208,240 or 480V)TPPH-F2-QD Thruway Pendant Power Hook Double Fuse, Quick Disconnect (Requires FL-1 andPHC. Specify voltage 208, 240 or 480V)TPPH-NEMA Thruway Pendant Power Hook (Requires FL-1 and PHC-XXXV-NEMA. Specify voltage)TWMBS Thruway Mounting BoxWG22/SGB22A Gym Wire Guard with Safety Glass Bottom for PD22 Refractor (Maximum 400W)LUMARKNOTES: 1. Open Rated (OR) socket and lamp must be used. 2. Metal halide available in non-U.S. markets only. 3. Not all options and configurations are compatible and restrictions may apply. Reference specification sheetfor additional details.Specifications and dimensions subject to change without notice. Consult your Cooper Lighting Representative or visit www.cooperlighting.com for available options, accessories and ordering information.15-7Cooper Lighting by Eaton Product Selection Guide Sixth Edition www.cooperlighting.com

ACRYLIC HIGH-BAYr Slide-on, die-cast aluminum mounting box with opening for 3/4" conduitr Heavy-duty, steel housing with open-air ballast for cooler operationr Standard white polyester, powder-paint finishr High power factor ballast with class H insulationr Minimum temperature: -40 C (-40 F) HPS, -30 C (-20 F) MH and MPr Reflectors and refractors can be changed to aluminum or glassr Mogul-base porcelain socketr Multiple field-adjustable distribution patterns for precision control16"26" [660mm]22"28-1/2" [724mm]25"29-1/16" [738mm]Compliances may not apply to all product configurations. Please consult the product spec sheet for compliance details.COMPLIANCES: UL Listed - Damp Location, CSA Listed, 40 C Ambient Temperature Rating,55 C Ambient Temperature Rating, EISA Compliant16" [406mm]22" [559mm]25" [635mm]Drop Bottom adds 3-1/2" [89mm]to overall height.SS PRISMATICSTEELER16", 22" AND 25"ORDERING INFORMATIONSAMPLE NUMBER: MPSS-PD22-M-400-MT-ORLamp TypeSeriesRefractor TypeRefractor DiameterDistributionLamp WattageVoltageSocketHP High Pressure SodiumMH Metal Halide 1,2MP Pulse Start MetalHalide 1SS SteelerPD PrismaticAcrylic16 16" Diameter22 22" Diameter25 25" DiameterC ConcentratedM MediumW WideHP250 250W400 400W600 600W750 750W120V 120V208V 208V240V 240V277V 277V347V 347V480V 480V5T 5-TapMT Multi-Tap wired 277VTT Triple-Tap wired 347V[Blank] Non Applicable (HPS ornot compatible with ORsocket)OR Open Rated Socket forMetal HalideMH1000 1000W175 175W250 250W400 400WMP175 175W200 200W250 250W320 320W350 350W400 400W450 450W750 750WOptions (Add as Suffix) 3C3 3" Cord with No Plug (Specify voltage)EM Quartz Restrike with "Delay Relay" (Quartz lamp strikes at both hot and cold starts)EM/SC Emergency Separate CircuitF1 Single Fuse (120, 277 or 347V only)F2 Double Fuse (208, 240 or 480V only)FH-1 Die-cast Aluminum Fixture Hook (With 3/4" threads for easy installation)FL-1 Malleable Iron Plated Fixture Loop (With 3/4" threads for easy installation)HC LumaWatt Fixture Control Module (Low voltage leads pulled out of top connection box for areasrequiring all wiring to be installed in conduit)HL LumaWatt Fixture Control Module (Allows low voltage control wire to be daisy-chained betweenfixtures outside AC conduit run similar to low voltage intercoms, fire alarms and phone systems)HSW Integral LumaWatt Sensor and Control with Wide DistributionL/TCB Less Top Connector Box (Housing shipped less top connector box. Specify when usingTWMBS accessory)LL Lamp IncludedP Pre-set Socket Position from the FactoryPC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Cord and Plug - 18" Power Cord and Non-NEMA Plug Configuration (Must be used withFL-1 and TPPH. Must specify single voltage)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)PS Protective Starter (Available in 1000W high pressure sodium only. For other wattages consultfactory)Q Quartz Restrike (Hot strike only)QD Quick Disconnect Die-cast Pendant Mount Box (Specify single voltage. Not compatible with PC3,PHC, C3, MWS, RM or HC)QLL Quartz Lamp Included (Lamp is Cooper designated product based on luminaire requirements.Lamp is shipped separate from luminaire unless otherwise noted)RM Remote MountSCF 3' Aircraft Safety Cable Secures Housing to Ceiling (Alternative lengths available. Example: SCF6 6' cable)SCR Aircraft Safety Cable-Housing to Reflector or RefractorSHK Die-cast Aluminum Fixture Hook (With safety screw and 3/4" threads for easy installation)SS Space Saver FeatureW/MWS MWS Industrial Components (Attached to the fixture at the factory. Standard cord length is 3foot; 6 foot and 11 foot also available. Please refer to MWS Modular Wiring System sectionfor additional information)Accessories (Order Separately)C3 3' Cord without Plug (Requires FH-1, FL-1 or SHK)CB22 Conical Bottom Lens for 22" Refractor (Maximum 400W)DB16 Drop Acrylic Lens for 16" Refractor (Maximum 250W)DB22 Drop Acrylic Lens for 22" Refractor (Maximum 400W)DB25 Drop Acrylic Lens for 25" Refractor (Maximum 400W)FH-1 Fixture HookFL-1 Fixture LoopFWG16/WDB Full Wire Guard for use with PD16 and DB16 Drop Lens (DB16 not included)FWG16/WG16 Full Wire Guard for PD16 (SGB16 not included)FWG16/WG16/SGB16A Full Wire Guard for 16" Refractor and SGB16 LensFWG22/WDB Full Wire Guard for use with PD22 and DB22 Drop Lens (DB22 not included)FWG22/WG22 Full Wire Guard for PD22 (SGB not included)FWG22/WG22/SGB22A Full Wire Guard for 22" Refractor and SGB22 Lens (Maximum 400W)FWG25/WDB Full Wire Guard for use with PD25 and DB25 Drop Lens (DB25 not included)FWG25/WG25 Full Wire Guard for PD25 (SGB not included)FWG25/WG25/SBG25A Full Wire Guard for 25" Refractor and SGB25 Lens (Maximum 400W)MBT Twin Mount Bracket (Fixtures must be same voltage and without hooks, loops or plugs)PC3 3' Cord with NEMA Plug (Other cord lengths are available by specifying length - PC6 for 6' cord.Requires FH-1 or FL-1 or SHK. Use with TPPH-NEMA. Specify voltage)PHC Power Hook Cord and Non-NEMA Plug Configuration (Must be used with FL-1 and TPPH)PHC-NEMA Power Cord and NEMA Plug - 18" Power Cord and 20 Amp NEMA Plug Configuration(Must be used with FL-1 and TPPH-NEMA)SGB16A Safety Glass Bottom for PD16 Refractor (Not compatible with WG16. Maximum 250W)SGB22A Safety Glass Bottom for PD22 Refractor (Not compatible with WG22. Maximum 400W)SGB25A Safety Glass Bottom for PD25 Refractor (Not compatible with WG25. Maximum 400W)SHK Hook with Safety ScrewTPPH Thruway Pendant Power Hook (Requires FL-1 and PHC. Specify voltage)TPPH-F Thruway Pendant Power Hook Single Fuse (Requires FL-1 and PHC. Specify voltage 120,277 or 347V)TPPH-F-QD Thruway Pendant Power Hook Single Fuse, Quick Disconnect (Requires FL-1 and PHC.Specify voltage 120, 277 or 347V)TPPH-F2 Thruway Pendant Power Hook Double Fuse (Requires FL-1 and PHC. Specify voltage 208,240 or 480V)TPPH-F2-QD Thruway Pendant Power Hook Double Fuse, Quick Disconnect (Requires FL-1 andPHC. Specify voltage 208, 240 or 480V)TPPH-NEMA Thruway Pendant Power Hook (Requires FL-1 and PHC-XXXV-NEMA. Specify voltage)TWMBS Thruway Mounting BoxWG16 Wire Guard for 16" Refractor (Not compatible with SGB)WG16/GLC Gym Wire Guard with Safety Glass for 16" RefractorWG16/SGB16A Gym Wire Guard with Safety Glass Bottom for 16" RefractorWG22 Wire Guard for PD22 Refractor (Not compatible with SGB)WG22/GLC Gym Wire Guard with Safety Glass for 22" RefractorWG22/SGB22A Gym Wire Guard with Safety Glass Bottom for PD22 Refractor (Maximum 400W)WG25 Wire Guard for PD25 Refractor (Not compatible with SGB25)WG25/GLC Gym Wire Guard with Safety Glass for 25" RefractorWG25/SGB25A Gym Wire Guard with Safety Glass Bottom for 25" RefractorWGD16 Wire Guard for DB16 RefractorWGD22 Wire Guard for DB22 Refractor (Not Compatible with SGB22)WGD25 Wire Guard for DB25 RefractorSpecifications and dimensions

Cooper Lighting by Eaton Product Selection Guide ixth Edition www.cooperlighting.com 15-2 Lumark Providing solutions for transportation, supermarkets, gymnasiums, factories, retail, warehouses and other industrial and commercial environments, Lumark offers a wide range of innovative prod