WIXLIB

Polystick PPOLYSTICK P is a homogeneous, rubberized asphalt waterproofingSelf-Adhered Roofing andWa t e r p r o o f i n g U n d e r l a y m e n tmembrane, surfaced with high strength polyethylene film laminate,PRODUCTDESCRIPTIONfor a dual waterproofing barrier.The film is specially treated with an anti-skid surfacing agent to provide traction.The rubberized asphalt seals around correctly installed nails on theweathering surface.Material is packaged in a roll of 36” width x 75’ length (202 sq.ft.finished roof coverage) weighing approx. 60 lbs.Material is available in patented box, EASYBOX (US PatentRECOMMENDEDAPPLICATIONQUALITY STANDARDS& APPROVALSD 479,685 S) that faciliates easy handling of rolls. ASTM D 1970 MIAMI-DADE County Product Control Approved(NOA # 002-0603.08) ICBO-ES ER# 5954POLYSTICK P uses include but are not limited to chimney flashings,skylight flashings, pipe penetrations, application at ridges andeaves, valley underlayments, and certain below grade waterproofing applications.Apply POLYSTICK P directly to the roof deck. Do not apply to shingles orH I P S A N D VA L L E Y Sother roof coverings. Apply only when the weather is dry and materialinterface temperatures (air, roof deck, membrane) are 40 F and rising.APPLICATION METHODSAlways start at the lowest point of the roof deck where possible. Cut theF O U N D AT I O NWAT E R P R O O F I N GPOLYSTICK P to a suitable, workable length (typically between 9 and 15feet). Lay the material flat in place, starting at the lowest point. Overlapseams 3.5” minimum and endlaps 6” minimum. Peel half of the backingTILEU N D E R L AY M E N Toff the roll and apply firm, even pressure from the center to the outeredges. Remove the backing from the remaining half of the roll and applypressure. Always ensure that POLYSTICK P is applied over the area tocover the highest point of “ice damming”. Be sure to follow all local building code recommendations and requirements with regards to width ofice dam materials. If full roof coverage application is desired, proper venting of the structure is required. Consult a design professional for properventing requirements. In steep slope applications (i. e. 3:12 slope orhigher) where backnailing is required, ensure that all nails are covered byoverlapping with the next sheet. POLYSTICK P must be covered within30 days of installation.M E TA LU N D E R L AY M E N T

Polystick IR-XPOLYSTICK IR-X, is a homogeneous, rubberized asphalt waterproofing compound, glass fiber reinforced, with a sand or a granularSelf-Adhered Roofing andWa t e r p r o o f i n g U n d e r l a y m e n tsurface for skid resistance.PRODUCTDESCRIPTIONThe rubberized asphalt seals around correctly installed nails on theweathering surface.Split release backing film aids in easy positioning of sheets tomaintain proper line.POLYSTICK IR-X membranes are manufactured using patentedADESO Self-Adhesive technology, a “true” whereby an APPcompound is applied on the top layer and an aggressive self-adhesive compound is applied on the bottom layer.Material is packaged in a roll of approx. 200 sq.ft. (finished roofcoverage) weighing approx. 75 lbs.Material is available in patented box, EASYBOX (US Patent DRECOMMENDEDAPPLICATIONQUALITY STANDARDS& APPROVALS479,685 S) that faciliates easy handling of rolls. ASTM D 1970 MIAMI-DADE County Product Control Approved(NOA # 002-0603.08) ICBO-ES ER# 5954POLYSTICK IR-X uses include but are not limited to: chimney flashings, skylight flashings, pipe penetrations, application at ridgesand eaves, valley underlayments, and certain below grade waterproofing applications.Apply POLYSTICK IR-X directly to the roof deck. Do not apply to shinglesH I P S A N D VA L L E Y Sor other roof coverings. Apply only when the weather is dry and materialinterface temperatures (air, roof deck, membrane) are 40 F and rising.APPLICATION METHODSAlways start at the lowest point of the roof deck where possible. Cut theF O U N D AT I O NWAT E R P R O O F I N GPOLYSTICK IR-X to a suitable, workable length (typically between 9 and15 feet). Lay the material flat in place, starting at the lowest point.Overlap seams 3.5” minimum and endlaps 6” minimum. Peel half of theTILEU N D E R L AY M E N Tbacking off the roll and apply firm, even pressure from the center to theouter edges. Remove the backing from the remaining half of the roll andapply pressure. Always ensure that POLYSTICK IR-X is applied over thearea to cover the highest point of “ice damming”. Be sure to follow alllocal building code recommendations and requirements with regards tothe width of ice dam materials. If full roof coverage application is desired,proper venting of the structure is required. Consult a design professionalfor proper venting requirements. In steep slope applications (i.e. 3:12slope or higher) where backnailing will be required, be sure that all nailsare covered by the overlapping next sheet. POLYSTICK IR-X must becovered within 90 days of installation.M E TA LU N D E R L AY M E N T

RECOMMENDEDAPPLICATIONQUALITY STANDARDS& APPROVALSPRODUCTDESCRIPTIONPolystick MUPOLYSTICK MU is a homogeneous rubberized asphalt waterproofingcompound, glass fiber reinforced with non-wiching fabric surface designedspecifically for use as an underlayment material for metal roofing. Therubberized asphalt adhesive membrane is well suited for use where a waterresistant barrier is required. This membrane is ideally suited for use undermetal roofing systems as well as under low-slope tile roof applications.POLYSTICK MU membrane has been specially formulated to withstand the highheat environment generated by metal roofing systems (Resistant to 260 F).Split release backing film aids in easy positioning of sheets to maintain proper line.POLYSTICK MU membranes are manufactured using patentedADESO Self-Adhesive technology, whereby a “true” an APPcompound is applied on the top layer and an aggressive self-adhesivecompound is applied on the bottom layer.Material is packaged in a roll of approx. 200 sq.ft. (finished roofcoverage) weighing approx. 80 lbs.Material is available in patented box, EASYBOX (US PatentD 479,685 S) that faciliates easy handling of rolls.Self-Adhered Roofing andWa t e r p r o o f i n g U n d e r l a y m e n t ASTM D 1970 MIAMI-DADE County Product Control Approved(NOA # 002-0603.08) ICBO-ES ER# 5954POLYSTICK MU uses include but are not limited to: application undermetal roofing and low slope tile roofing where a water resistant barrier is required. It is also suited for application in desert climaticconditions. POLYSTICK MU has been specially formulated to be hightemperature resistant up to 260 F. POLYSTICK MU may be leftexposed to the elements for up to 90 days before application ofmetal roofing.POLYSTICK MU is to be applied directly to the acceptable substrate.H I P S A N D VA L L E Y SDo not apply to shingles or other roof coverings. Apply only whenAPPLICATION METHODSthe weather is dry and material interface temperatures (air, roofdeck, membrane) are 40 F and rising. Always start at the lowestF O U N D AT I O NWAT E R P R O O F I N Gpoint of the roof deck where possible. Cut the POLYSTICK MU to asuitable, workable length. (This will vary depending on the numberof workers and length of runs). Lay the material flat in place, over-TILEU N D E R L AY M E N Tlap seams 3.5” minimum and endlaps 6” minimum. Peel half of thebacking off the roll and apply firm, even pressure from the center tothe outer edges. Remove the backing from the remaining half of theroll and apply pressure in the same manner. For full roof coverageapplication, proper venting of the structure is required. Consult adesign professional to assure proper venting requirements have beenachieved. In steep slope applications (i.e. 3:12 slope or higher)where backnailing will be required, be sure that all nails are coveredby the overlapping next sheet. POLYSTICK MU must be covered within90 days of installation.M E TA LU N D E R L AY M E N T

Polystick TUPOLYSTICK TU, is a homogeneous rubberized asphalt waterproofingcompound, glass fiber reinforced, with granular surface designedSelf-Adhered Roofing andWa t e r p r o o f i n g U n d e r l a y m e n tspecifically for use as tile underlayment.PRODUCTDESCRIPTIONThe rubberized asphalt seals around correctly installed nails of theweathering surface. Split release backing film aids in the easypositioning of sheets to maintain proper line.POLYSTICK TU membranes are manufactured using patentedADESO Self-Adhesive technology, whereby a “true” APPcompound is applied on the top layer and an aggressiveself-adhesive compound is applied on the bottom layer.Material is packaged in a roll of approx. 100 sq.ft. (finished roofcoverage) weighing approx. 75 lb.Material is available in patented box, EASYBOX (US PatentRECOMMENDEDAPPLICATIONQUALITY STANDARDS& APPROVALSD 479,685 S) that faciliates easy handling of rolls. ASTM D 1970 MIAMI-DADE County Product Control Approved(NOA # 002-0603.08) ICBO-ES ER# 5954POLYSTICK TU uses include but are not limited to: tile underlayment,chimney flashings, skylight flashings, pipe penetrations, applicationat ridges and eaves, valley underlayments, and certain below gradewaterproofing applicationsApply POLYSTICK TU directly to the roof deck. Do not apply toH I P S A N D VA L L E Y Sshingles or other roof coverings. Apply only when the weather isdry and material interface temperatures (air, roof deck, mem-APPLICATION METHODSbrane) are 40 F and rising. Always start at the lowest point ofF O U N D AT I O NWAT E R P R O O F I N Gthe roof deck where possible. Cut POLYSTICK TU to a suitable,workable length (typically between 9 and 15 feet). Lay the mate-TILEU N D E R L AY M E N Trial flat in place, starting at the lowest point. Overlap seams3.5” minimum and endlaps 6” minimum. Peel half of thebacking off the roll and apply firm, even pressure from the center to the outer edges. Remove the backing from the remaininghalf of the roll and apply pressure. In full roof coverage applications, proper venting of the structure is required.Consult a design professional for proper venting requirements.In steep slope applications (i.e. 3:12 slope or higher) wherebacknailing will be required, be sure that all nails are coveredby the overlapping next sheet. POLYSTICK TU must be coveredwithin 90 days of installation.M E TA LU N D E R L AY M E N T