Transcription
Q R N G SeriesModel QRNG 216Parts ManualRecord of Change 100This manual contains important safety information and must be madeavailable to all personnel who operate and/or maintain this product.Carefully read this manual before attempting to operate or performmaintenance on this compressor.Fill Out & Return Warranty Registration Card Located InsideManual No. 50168-100April 2008 Edition
INTRODUCTIONMODEL &SERIAL NUMBERIDENTIFICATIONThis manual provides information for the QRNGSeries, Model QRNG216 natural gas compressor perRecord of Change 100.RecordofChange No.The Model QRNG216 natural gas compressor is anaircooled, single stage, two cylinder, pressure lubricated compressor, capable of handling inlet pressuresof -75 PSIG (15 in. mercury) up to 50 PSIG. Up to 150PSIG of discharge pressure can be produced. It has a3" bore, with a 2 1/2" stroke and can be run at 400-900RPM.CHANGESModel & Serial NumberIdentification TagInitial printing.The serial number identification tag is located on thehand hole plate side of the crankcase. Fill in thenumbers from your compressor in the correspondingspaces provided here, and reference this page whenordering replacement parts.TABLE OF CONTENTSOrdering Replacement Parts . 1Serial Number Identification . 1All replacement parts are to be ordered through anauthorized Quincy gas application distributor. Insiston genuine Quincy parts only! Failure to do so mayvoid warranty.Crankcase Lubricant Capacity . 1Crankcase Group . 2Crankshaft Group . 3Bearing Carrier Group . 4-5CRANKCASE LUBRICANTACITYCAPCAPACITYConnecting Rod & Piston Group . 6-7Cylinder & Head Groups . 8-11Head Assemblies . 12-13Control Group . 14ModelCapacityQRNG 2161 Qt - 16 Oz. (1.42 lit.)Recommended Spare Parts . 15Quin-Cip Lubricant . 15CAUTION !Decals . 15Refer to the Quincy QRNG Series instruction manual forvital lubrication information.Gasket Set . 15WARNING !ORDERINGREPLACEMENT PARTSFollow all safety precautions outlined in the Quincy QRNGSeries instruction manual.Prompt service can be rendered on repair parts ordersif the following information is given:CAUTION !Item 1) the model number, record of change number, & serial number.Item 2) the exact part number needed. (Do notorder by item numbers.)Item 3) the exact quantity needed.Item 4) the preferred type of transportation.Do not operate this compressor without a totally enclosedbelt guard or any other required safety equipment.DANGER !Air used for breathing or food processing must meet OSHA1910.134 or FDA 21 CFR 178.3570 regulations. Failure to doso may cause severe injury or death.QRNG 21650168-100, April 2008Quincy Compressor13501 Wismann Lane, Quincy IL - 62305-3116
CRANKCASE GROUP 41516‡ 7011462922749-112110419-010Descriptioncrankcase assemblycrankcasebearing cupshim, bearing adjustment, .002 steelshim, bearing adjustment, .005, steelshim, bearing adjustment, .007, steelshim, bearing adjustment, .020, steelshim, bearing adjustment, .005, paperadjustment plate assemblyplate, adjustment (.0015/.003 crankshaft end play)oil sealhex. screw, 3/8-16 unc x .75, grade 5 (@ 30 ft.-lbs.)inspection plategasket, inspection plateoil gaugepipe plug, 3/8 nptscreengasket, inlet screw"o"ring, 3/32 wide x .94 o.d.gasket, inlet screwoil inlet screwbreather assemblybreather bodybreather tubeballroll pintubehex. screw, 5/16-18 unc x 1.00, grade 5 (@ 60 in.-lbs.)"o"ring, 3/32 wide x .69 o.d.tube fitting, 90 male elbow, 3/8 tube x 3/8 npt* Quantity as required@ Indicates torque value (dry threads)‡ Assemble item 19 into item 17 with Loctite 609.Apply pipe sealantto this pinduring installation.QRNG 21650168-100, April 2008Quincy Compressor23501 Wismann Lane, Quincy IL - 62305-3116
CRANKSHAFT GROUP 110428W038Descriptioncrankshaft assemblycrankshaft (N.S.S.; order 110219)orifice, 1/8 nptpipe plug, 1/8 nptbearing conebearing conepinkeysheave assemblycompressor sheave, 14", 1G,B sect, ccw (N.S.S.; order 2917X)socket head screw, 3/8-16 unc X 2.75, Grade 5 (@ 30 ft.-lbs.)square nut, 3/8-16 uncflatwasher, 3/8N.S.S. Not Sold Separate@ Indicates torque value (dry threads)1.31.41.11.63.11.321.21.53.23.43.3QRNG 21650168-100, April 2008Quincy Compressor33501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP 110815-005QRNG 21650168-100, April 2008Quincy Compressor43501 Wismann Lane, Quincy IL - 62305-3116
BEARING CARRIER GROUP scriptionbearing carrier assembly (N.S.S.; order 110809X005)bearing carrier (N.S.S.; order 110809X005)includes:cup, bearingbushing"o"ring, 3/32 wide x 3.44 o.d."o"ring, 3/32 wide x .69 o.d.driveshaftdriveshaft keypump gerotorretaining ringoil pump housinghex. screw, 1/4-20 unc x 1.00, grade 5 (@ 6 ft.-lbs.)pipe plug, 1/4 npt, hex socketadjustment screw"o"ring, 1/16 wide x .44 o.d.jamnut, 9/16-18 unfspringneedle valvehole plugpipe plug, 1/8 nptgasket, bearing carrierhex. screw, 3/8-16 unc x 1.00, grade 5 (@ 30 ft.-lbs.)* oil pressure gaugestudoil filterMaintenance Parts160078-001110809X005Oil Pump Repair Kitincludes "o"rings, driveshaft, key & retaining ringReplacement Bearing Carrier Assemblyincludes bearing carrier assembly, oil filter, stud & bearing carrier gasketN.N.S. Not Sold Separate@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bringeach fastener to the recommended torque specification in even increments.* Should indicate approximately 25 psig at operating temperature.QRNG 21650168-100, April 2008Quincy Compressor53501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110260-002(2 required per compressor)Cross Sectional ViewofPiston & Ringstypicalpip marklocation(top of ring)Stagger ring gapsduring assembly!QRNG 21650168-100, April 2008Quincy Compressor63501 Wismann Lane, Quincy IL - 62305-3116
CONNECTING ROD & PISTON GROUP 110260-002(2 required per 2824124471-K08connecting rod assembly (N.S.S.; order 110703X103)connecting rod (N.S.S.; order 110703X103)connecting rod bearingconnecting rod bolt 5/16-24 unfconnecting rod washerretaining ringpiston pinpistonoil ring railoil ring expandercompression ringcon rod bearing insert (N.S.S.; order 2824PR)locknut, 5/16-24 unf (@ 19 425-0202110703X103inserts (pair), con rod bearing,(standard)inserts (pair), con rod bearing, (.010 oversize)piston (.010 oversize)piston (.020 oversize)Ring Set (standard) no color codeincludes compression ring, oil ring rails & expander (for one piston)Ring Set (.010 oversize; light blue)includes compression rings, oil ring rails & expander (for one piston)Ring Set (.020 oversize; yellow)includes compression rings & oil ringPiston Assembly (standard)includes piston, piston pin, retaining rings & ring setPiston Assembly (.010 oversize)includes piston, piston pin, retaining rings & ring setPiston Assembly (.020 oversize)includes piston, piston pin, retaining rings & ring setRing Set (.020 oversize; yellow)includes piston, piston pin, retaining rings & ring setReplacement Connecting Rod Assemblyincludes connecting rod assembly, locknuts & con-rod bearing insertsMaintenance PartsN.S.S. Not Sold Separate@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bringeach fastener to the recommended torque specification in even increments.* 1 pair required for each connecting rod assembly.QRNG 21650168-100, April 2008Quincy Compressor73501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 110252-003(plain head)QRNG 21650168-100, April 2008Quincy Compressor83501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 110252-003(plain 0386-L1219361836head assemblygasketcylindergasket, cylinderhex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)lockwasher, 3/8counterbore screw, 3/8-16 unc x 1.00, grade 8 (@ 30 ft.-lbs.)hex. screw, 3/8-16 unc x 3.00, grade 5 (@ 30 ft.-lbs.)washer1911GPReplacement Head Assemblyincludes head assembly & head gasketMaintenance Parts@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bringeach fastener to the recommended torque specification in even increments.QRNG 21650168-100, April 2008Quincy Compressor93501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 110255-002(head with unloaders)QRNG 21650168-100, April 2008Quincy Compressor103501 Wismann Lane, Quincy IL - 62305-3116
CYLINDER & HEAD GROUP 110255-002(head with 115-06C90386-L1219361836head assemblygasketcylindergasket, cylinderhex. screw, 3/8-16 unc x 1.25, grade 5 (@ 30 ft.-lbs.)lockwasher, 3/8counterbore screw, 3/8-16 unc x 1.00, grade 8 (@ 30 ft.-lbs.)hex. screw, 3/8-16 unc x 3.00, grade 5 (@ 30 ft.-lbs.)washer1911X38PULReplacement Head Assemblyincludes head assembly & head gasketMaintenance Parts@ Indicates torque value (dry threads). Tighten multiple bolts, capscrews & hex nuts in a criss-cross or alternating pattern. Bringeach fastener to the recommended torque specification in even increments.QRNG 21650168-100, April 2008Quincy Compressor113501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 1911PASSEMBLY(plain head)QRNG 21650168-100, April 2008Quincy Compressor123501 Wismann Lane, Quincy IL - 62305-3116
HEAD ASSEMBLY 1911-2UUASSEMBLY(head with unloaders)QRNG 21650168-100, April 2008Quincy Compressor133501 Wismann Lane, Quincy IL - 62305-3116
CONTROL GROUP 116269-001QRNG 21650168-100, April 2008Quincy Compressor143501 Wismann Lane, Quincy IL - 62305-3116
Recommended Spare 785508Descriptionreplacement suction valve assy.replacement discharge valve assy.pressure gaugeoil pump repair kitgasket set213DecalsQUIN-CIP LUBRICANTItem#Qty.Refer to the chart below to order Quin-Cip compressor lubricant from your local authorized Quincy gasapplication distributor.PackagePart No.DescriptionBarrelPailGallonGallon CaseQuartQuart Q032112541C03255 gal., SAE 10W5 gal., SAE 10W1 gal., SAE 10W(4)-1 gal., SAE 10W1 qt., SAE 10W(12)-1 qt., SAE 10WBarrelPailGallonGallon CaseQuartQuart Q068112542C06855 gal., SAE 205 gal., SAE 201 gal., SAE 20(4)-1 gal., SAE 201 qt., SAE 20(12)-1 qt., SAE 20BarrelPailGallonGallon CaseQuartQuart Q100112543C10055 gal., SAE 305 gal., SAE 301 gal., SAE 30(4)-1 gal., SAE 301 qt., SAE 30(12)-1 qt., SAE 30123110831127889-A127889-BDescriptionserial number & nameplatedecal, CAUTION!, MANUALdecal, DANGER!,"Air from this."Gasket Set 5508GItem#Qty.44112216211QRNG 21650168-100, April 21832A1832B1832C1832D1943-16274-1Descriptionvalve gasketvalve gasketgasketgasket, inspection plateshim, bearing adj., .005, steelshim, bearing adj., .007, steelshim, bearing adj., .020, steelshim, bearing adj., .005, papershim, bearing adj., .002 stl.head gasketbearing carrier gasketQuincy Compressor153501 Wismann Lane, Quincy IL - 62305-3116
QUINCY COMPRESSORSTANDARD TERMS AND CONDITIONSLEGAL EFFECT: Except as expressly otherwise agreed to in writing by an authorized representative of Seller, thefollowing terms and conditions shall apply to and form a part of this order and any additional and/or different termsof Buyer’s purchase order or other form of acceptance are rejected in advance and shall not become a part of thisorder.The rights of Buyer hereunder shall be neither assignable nor transferable except with the written consent of Seller.This order may not be canceled or altered except with the written consent of Seller and upon terms which will indemnifySeller against all loss occasioned thereby. All additional costs incurred by Seller due to changes in design orspecifications, modification of this order or revision of product must be paid for by Buyer.In addition to the rights and remedies conferred upon Seller by this order, Seller shall have all rights and remediesconferred at law and in equity and shall not be required to proceed with the performance of this order if Buyer is indefault in the performance of such order or of any other contract or order with seller.TERMS OF PAYMENT: Unless otherwise specified in the order acknowledgment, the terms of payment shall be 1%15, net forty-five (45) days after shipment. These terms shall apply to partial as well as complete shipments. If anyproceeding be initiated by or against Buyer under any bankruptcy or insolvency law, or in the judgment of Seller thefinancial condition of Buyer, at the time the equipment is ready for shipment, does not justify the terms of paymentspecified, Seller reserves the right to require full payment in cash prior to making shipment. If such payment is notreceived within fifteen (15) days after notification of readiness for shipment, Seller may cancel the order as to anyunshipped item and require payment of its reasonable cancellation charges.If Buyer delays shipment, payments based on date of shipment shall become due as of the date when ready forshipment. If Buyer delays completion of manufacture, Seller may elect to require payment according to percentageof completion. Equipment held for Buyer shall be at Buyer’s risk and storage charges may be applied at the discretionof Seller.Accounts past due shall bare interest at the highest rate lawful to contract for but if there is no limit set by law, suchinterest shall be eighteen percent (18%). Buyer shall pay all cost and expenses, including reasonable attorney’s fees,incurred in collecting the same, and no claim, except claims within Seller’s warranty of material or workmanship, asstated below, will be recognized unless delivered in writing to Seller within thirty (30) days after date of shipment.TAXES: All prices exclude present and future sales, use, occupation, license, excise, and other taxes in respect ofmanufacture, sales or delivery, all of which shall be paid by Buyer unless included in the purchase price at the properrate or a proper exemption certificate is furnished.ACCEPTANCE: All offers to purchase, quotations and contracts of sales are subject to final acceptance by anauthorized representative at Seller’s plant.DELIVERY: Except as otherwise specified in this quotation, delivery will be F. O. B. point of shipment. In the absenceof exact shipping instruction, Seller will use its discretion regarding best means of insured shipment. No liability willbe accepted by Seller for so doing. All transportation charges are at Buyer’s expense. Time of delivery is an estimateonly and is based upon the receipt of all information and necessary approvals. The shipping schedule shall not beconstrued to limit seller in making commitments for materials or in fabricating articles under this order in accordancewith Seller’s normal and reasonable production schedules.Seller shall in no event be liable for delays caused by fires, acts of God, strikes, labor difficulties, acts of governmentalor military authorities, delays in transportation or procuring materials, or causes of any kind beyond Seller’s control.No provision for liquidated damages for any cause shall apply under this order. Buyer shall accept delivery withinthirty (30) days after receipt of notification of readiness for shipment. Claims for shortages will be deemed to havebeen waived if not made in writing with ten (10) days after the receipt of the material in respect of which any suchshortage is claimed. Seller is not responsible for loss or damage in transit after having received “In Good Order”receipt from the carrier. All claims for loss or damage in transit should be made to the carrier.QRNG 21650168-100, April 2008Quincy Compressor163501 Wismann Lane, Quincy IL - 62305-3116
TITLE & LIEN RIGHTS: The equipment shall remain personal property, regardless of how affixed to any realty orstructure. Until the price (including any notes given therefore) of the equipment has been fully paid in cash, Sellershall, in the event of Buyer’s default, have the right to repossess such equipment.PATENT INFRINGMENT: If properly notified and given an opportunity to do so with friendly assistance, Seller willdefend Buyer and the ultimate user of the equipment from any actual or alleged infringement of any published UnitedStates patent by the equipment or any part thereof furnished pursuant hereto (other than parts of special design,construction, or manufacture specified by and originating with Buyer), and will pay all damages and costs awardedby competent court in any suit thus defended or of which it may have had notice and opportunity to defend as aforesaid.STANDARD WARRANTY: Seller warrants that products of its own manufacture will be free from defects inworkmanship and materials under normal use and service for the period specified in the product instruction manual.Warranty for service parts will be Ninety (90) days from date of factory shipment. Electric Motors, gasoline and dieselengines, electrical apparatus and all other accessories, components and parts not manufactured by Seller arewarranted only to the extent of the original manufacturer’s warranty.Notice of the alleged defect must be given to the Seller, in writing with all identifying details including serial number,type of equipment and date of purchase within thirty (30) days of the discovery of the same during the warranty period.Seller’s sole obligation on this warranty shall be, at its option, to repair or replace or refund the purchase price of anyproduct or part thereof which proves to be defective. If requested by Seller, such product or part thereof must bepromptly returned to seller, freight prepaid, for inspection.Seller warrants repaired or replaced parts of its own manufacture against defects in materials and workmanship undernormal use and service for ninety (90) days or for the remainder of the warranty on the product being repaired.This warranty shall not apply and Seller shall not be responsible or liable for:(a)Consequential, collateral or special losses or damages;(b)Equipment conditions caused by fair wear and tear, abnormal conditions of use, accident, neglect or misuseof equipment, improper storage or damage resulting during shipping;(c)Deviation from operating instructions, specifications or other special terms of sale;(d)Labor charges, loss or damage resulting from improper operation, maintenance or repairs made byperson(s) other than Seller or Seller’s authorized service station.In no event shall Seller be liable for any claims whether arising from breach of contract or warranty or claims ofnegligence or negligent manufacture in excess of the purchase price.THIS WARRANTY IS THE SOLE WARRANTY OF SELLERS AND ANY OTHER WARRANTIES, WHETHEREXPRESS OR IMPLIED IN LAW OR IMPLIED IN FACT, INCLUDING ANY WARRANTIES OF MERCHANTABILITYAND FITNESS FOR PARTICULAR USE ARE HEREBY SPECIFICALLY EXCLUDED.LIABILITY LIMITATIONS: Under no circumstances shall the Seller have any liability for liquidated damages or forcollateral, consequential or special damages or for loss of profits, or for actual losses or for loss of production orprogress of construction, whether resulting from delays in delivery or performance, breach of warranty, negligentmanufacture or otherwise.ENVIROMENTAL AND OSHA REQUIREMENTS: At the time of shipment of the equipment from the factory, QuincyCompressor / Ortman Fluid Power will comply with the various Federal, State and local laws and regulationsconcerning occupational health and safety and pollution. However, in the installation and operation of the equipmentand other matters over which the seller has no control, the Seller assumes no responsibility for compliance with thoselaws and regulations, whether by the way of indemnity, warranty or otherwise.June 30, 2003QRNG 21650168-100, April 2008Quincy Compressor173501 Wismann Lane, Quincy IL - 62305-3116
Reciprocating / Systems:Reciprocating217.222.7700Air ssor.comquincycompressor.comquincyairmaster.com 2006 Quincy Compressor, an EnPro Industries companyAll Rights Reserved. Litho in U.S.A.
Parts Manual Record of Change 100 . Refer to the Quincy QRNG Series instruction manual for vital lubrication information. CAUTION ! QRNG 216 Quincy Compressor 50168-100, April 2008 2 3501 Wismann Lane, Quincy IL - 62305-3116 CRANKCASE GROUP 110250-002 ItemItemItem PartPartPart
