Transcription
FINAL ADJUSTMENT AND REGULATING PROCEDUREDELAYEDACTIONVALVE(OPTIONAL)1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODYAND FOOT ON DOOR AND FRAME.BACKCHECKVALVEDELAYED ACTIONRANGE1/4" SPRING POWERADJUSTMENT SCREWCLOSINGSPEED VALVEBREGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISETO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOORMOVEMENT.FASTER( )DFOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THATSHOWN FOR MOUNTING THE CLOSER BODY.BREGULATING BACKCHECKSARGENT 1430SERIES CLOSERSHOWN. (OTHERSERIES SIMILAR)SEE NOTE #1 BELOW FOR DIMENSIONINFORMATION. IF A DIMENSION LESS THAN7/8" IS USED. THE DOOR STOP MUST BE CUTTO CLEAR THE MORTISE NUT HEAD OR THEMORTISE NUT HEAD MUST BE RECESSED.(SEE ENLARGED VIEW "Y")CLOSER MOUNTED ONHINGE SIDE OF DOORE NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREWFROM FACTORY SETTING (USE CHART AS GUIDE ONLY)281INTERIOR DOORSAPPROXIMATEEXTERIOR DOORSDOOR WEIGHT (POUNDS)FACTORY SET801101-5 CW1151-5 CCW1305-8 CW1501558-13 CWFACTORY SET1651701-5 CW13-15 CW180UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.NOTE: FOR 08 AND OLC TYPE ARMS MOUNTINGSEE DATA SHEETS ENCLOSEDDOOR STOPMORTISE NUT HEADDOORDRILL 3/8" DIA.HOLE FOR MORTISENUT BODY.DRILL 1/4" DIA. HOLEFOR MOUNTING SCREWS*ADJUST SPRING POWER ACCORDING TO CHART TOP JAMBAPPLICATION(TYPE 25-O, 25-OZAND 25-OZA ARMS)MOVE FOOTPIVOT TO HOLENEAREST HINGE DOOR WIDTH(INCHES)243032364042444648OVER 48USEPAGE 2FRAMEADJUSTING FOOT FOR ADDITIONAL CLOSING POWER(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)HINGE EDGE OF DOORTURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTERCLOCKWISE TO SPEED UP DOOR MOVEMENTSTANDARD & TOP JAMB APPLICATIONSSTANDARD APPLICATION(TYPE 25-O ARM)4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTSARE TIGHTENED.LATCHINGSPEED RANGECOVER“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGHDELAYED ACTION RANGE1BACKCHECKRANGETO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVECLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASECHECKING.CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT ISDAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.NEVER USE BACKCHECK AS A DOOR STOP.ALWAYS USE A DOOR STOP TO STOP THE DOOR.SLOWER(–)281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.CLOSING SPEEDRANGELATCHINGSPEEDVALVEAMODEL 281 POWERGLIDE SERIESINSTRUCTIONS FOR INSTALLING SARGENT DOORCLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)USING MORTISE NUTS WITH SARGENT DOOR TER CLOCKWISE(CCW)1/4" ALLEN SPRING POWERADJUSTING SCREWSARGENT 351 SERIES SHOWNLEFTHAND DOOR1/8"SHORTEN MORTISENUT BODY TOTHIS LENGTH5/8" DIA. HOLESTOP (PUSH) SIDECLOSER MOUNTED ON FRAMEON STOP SIDE OF DOORFRAMEINSTALL COVER WITH TWO SCREWS AS SHOWN.PULLHINGE SIDEPULLHINGE SIDERIGHTHAND DOORSTOP (PUSH) SIDEUSEPAGE 3DOORSTOPPARALLEL APPLICATION ONLYDOOR351 DOOR CLOSER SHOWN(TRACK ASSEMBLYMOUNTING IS SIMILAR)1/4" DIA.DRILLED HOLE#12-24 THREADMORTISE NUT9/16"DIA.MORTISE NUTHEAD3/8" DIA. HOLEPARALLEL ARMAPPLICATION(TYPE 25-P9)VIEW "Y"7/64"USEPAGE 41-11/16" FOR 1-3/4" THICK DOOR1-5/16" FOR 1-3/8" THICK DOOR(SEE NOTE #4 FOR 2-1/4" THICK DOORS)INSERT IS REMOVABLE.PLACE IN UNUSED OPENING.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E5CLOSER MOUNTED ONSTOP SIDE OF DOORCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E6DOOR WIDTH(INCHES)243032364042444648OVER 48NUMBER OF TURNS OF SPRING POWER ADJUSTING NUTFROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORSAPPROXIMATE281DOOR WEIGHT (POUNDS)EXTERIOR DOORS802-7 CW1101157-11 CW1-5 CCW130150FACTORY SET11-15 CW15516517015-17 CW1-8 CW180UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGSARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNINGSPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREWCOUNTERCLOCKWISE.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E1
281 STANDARD APPLICATION FOR INSTRUCTIONS281 TOP JAMB APPLICATION INSTRUCTIONSIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGARMTYPEMOUNTINGMAX. DOOROPENINGIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGDIM.ADIM.BDIM.AREVEALDEPTHARMTYPEMAX. DOOROPENINGMAX. DOOROPENINGDIM. "B"REGULARARM NOHOLDERSTANDARD7"12-1/8"5"10-1/8""A"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLATHEAD MACHINE SCREWS2"1-1/4"1RIGHT HAND DOOR SHOWN. LEFT HANDDOOR OPPOSITE.0" TO 2"9-5/16"“OZ” ARM2-1/8" TO 5"10-1/8"“OZA” ARM5-1/8" TO 5"10-15/16"THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.1"DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISENUTS WHEN REQUIRED.ALTERNATE MOUNTING ISRECOMMENDED FOR ADACOMPLIANT DOORSCL OF HINGE PIVOT:BUTTS, OFFSET PIVOTS,SWING CLEAR, CENTER HUNGOR INVISIBLE HINGES5/8"FRAMETOPOFDOOR10-3/8"#12 X 1-1/2" WOOD SCREWSOR #12-24 X 5/8 FLAT HEADMACHINE SCREW10-3/8"3-5/8"7/8"2“O” ARM1LEFT HAND DOOR SHOWN, RIGHTHAND DOOR OPPOSITE.2THESE DIMENSIONS MAYBE REDUCED TO 3/8"MIN. IF RAIL ON TOP CASING IS NARROW ORLOW CEILING CONDITION EXISTS. CLOSERFOOT SHOULD BE MOVED ACCORDINGLY.13THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.2DIM.ALTERNATE281 PARALLEL ARM APPLICATION INSTRUCTIONS4-1/2"10-1/2"HINGE PIVOT:BUTT, OFFSET PIVOTS, SWING CLEAR,CENTERHUNG OR INVISIBLE HINGES2-1/2"1-1/4"1/2"7-5/8"DOORLEFT HAND DOOR SHOWN. RIGHT HANDDOOR DIMENSION OPPOSITE.7/8"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.TOP VIEW#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWSDO NOT USE THIS MOUNTING FOR“SWING CLEAR” HINGES.5/16"DIM. B3THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.4MAY BE REDUCED BY 1/2" TO AVOIDDOOR TRIM.DIM. ASTOPCL OF BRACKET1"DIM."A"USE MOUNTING BRACKETAS DRILL THRU TEMPLATETOP OFDOORUSE MOUNTING BRACKETAS A DRILL-THRU TEMPLATE1-5/8"ATOP OFDOOR3"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.2"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWS1"CL OF PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.DIM.B1-5/8"10-3/8"REMOVE BACKING FROM SELF ADHESIVE TAPE ANDUSE BRACKET AS DRILL THROUGH TEMPLATE.HINGEADIM.AINSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.BATTACH FOOT TO DOOR WITHPIVOT AWAY FROM HINGE.ACL OF HINGE PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORSAND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.BATTACH FOOT BRACKET TO FRAME STOP.RIGHT HANDDOOR SHOWNRIGHT HANDDOOR SHOWNCRIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)PIVOTCP3 OR P3ABRACKETINSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.(SARGENT#590 SHOWN)P4 OR P4ABRACKETINDEX MARKON SPINDLEMAIN ARMLEFT HANDDOOR54OPTIONAL ARMS FOR MOUNTING. SEE DATASHEET ENCLOSED.5MAINARM42311ROD2ARMSCREWINDEX MARKON SPINDLERIGHT HANDDOOR35MAINARMINDEXMARKONSPINDLE42CRIGHT HANDDOOR SHOWNATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW ANDWASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.31BATTACH FOOT TO FRAME WITH PIVOTAWAY FROM HINGE.POSITION OFMAIN ARM WHENASSEMBLINGTO SPINDLEFOR FLUSH FRAMEAND DOOR CONDITIONSSWIVEL ARMCAUTION: DOOR CLOSER WILL NOT OPERATEPROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E2Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E3FOR USE WITH OVERHEADDOOR HOLDERSP4A BRACKET IS USEDWITH OVERHEAD HOLDERSCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E4
281 STANDARD APPLICATION FOR INSTRUCTIONS281 TOP JAMB APPLICATION INSTRUCTIONSIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGARMTYPEMOUNTINGMAX. DOOROPENINGIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGDIM.ADIM.BDIM.AREVEALDEPTHARMTYPEMAX. DOOROPENINGMAX. DOOROPENINGDIM. "B"REGULARARM NOHOLDERSTANDARD7"12-1/8"5"10-1/8""A"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLATHEAD MACHINE SCREWS2"1-1/4"1RIGHT HAND DOOR SHOWN. LEFT HANDDOOR OPPOSITE.0" TO 2"9-5/16"“OZ” ARM2-1/8" TO 5"10-1/8"“OZA” ARM5-1/8" TO 5"10-15/16"THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.1"DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISENUTS WHEN REQUIRED.ALTERNATE MOUNTING ISRECOMMENDED FOR ADACOMPLIANT DOORSCL OF HINGE PIVOT:BUTTS, OFFSET PIVOTS,SWING CLEAR, CENTER HUNGOR INVISIBLE HINGES5/8"FRAMETOPOFDOOR10-3/8"#12 X 1-1/2" WOOD SCREWSOR #12-24 X 5/8 FLAT HEADMACHINE SCREW10-3/8"3-5/8"7/8"2“O” ARM1LEFT HAND DOOR SHOWN, RIGHTHAND DOOR OPPOSITE.2THESE DIMENSIONS MAYBE REDUCED TO 3/8"MIN. IF RAIL ON TOP CASING IS NARROW ORLOW CEILING CONDITION EXISTS. CLOSERFOOT SHOULD BE MOVED ACCORDINGLY.13THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.2DIM.ALTERNATE281 PARALLEL ARM APPLICATION INSTRUCTIONS4-1/2"10-1/2"HINGE PIVOT:BUTT, OFFSET PIVOTS, SWING CLEAR,CENTERHUNG OR INVISIBLE HINGES2-1/2"1-1/4"1/2"7-5/8"DOORLEFT HAND DOOR SHOWN. RIGHT HANDDOOR DIMENSION OPPOSITE.7/8"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.TOP VIEW#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWSDO NOT USE THIS MOUNTING FOR“SWING CLEAR” HINGES.5/16"DIM. B3THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.4MAY BE REDUCED BY 1/2" TO AVOIDDOOR TRIM.DIM. ASTOPCL OF BRACKET1"DIM."A"USE MOUNTING BRACKETAS DRILL THRU TEMPLATETOP OFDOORUSE MOUNTING BRACKETAS A DRILL-THRU TEMPLATE1-5/8"ATOP OFDOOR3"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.2"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWS1"CL OF PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.DIM.B1-5/8"10-3/8"REMOVE BACKING FROM SELF ADHESIVE TAPE ANDUSE BRACKET AS DRILL THROUGH TEMPLATE.HINGEADIM.AINSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.BATTACH FOOT TO DOOR WITHPIVOT AWAY FROM HINGE.ACL OF HINGE PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORSAND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.BATTACH FOOT BRACKET TO FRAME STOP.RIGHT HANDDOOR SHOWNRIGHT HANDDOOR SHOWNCRIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)PIVOTCP3 OR P3ABRACKETINSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.(SARGENT#590 SHOWN)P4 OR P4ABRACKETINDEX MARKON SPINDLEMAIN ARMLEFT HANDDOOR54OPTIONAL ARMS FOR MOUNTING. SEE DATASHEET ENCLOSED.5MAINARM42311ROD2ARMSCREWINDEX MARKON SPINDLERIGHT HANDDOOR35MAINARMINDEXMARKONSPINDLE42CRIGHT HANDDOOR SHOWNATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW ANDWASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.31BATTACH FOOT TO FRAME WITH PIVOTAWAY FROM HINGE.POSITION OFMAIN ARM WHENASSEMBLINGTO SPINDLEFOR FLUSH FRAMEAND DOOR CONDITIONSSWIVEL ARMCAUTION: DOOR CLOSER WILL NOT OPERATEPROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E2Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E3FOR USE WITH OVERHEADDOOR HOLDERSP4A BRACKET IS USEDWITH OVERHEAD HOLDERSCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E4
281 STANDARD APPLICATION FOR INSTRUCTIONS281 TOP JAMB APPLICATION INSTRUCTIONSIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGARMTYPEMOUNTINGMAX. DOOROPENINGIMPORTANT: USE ALTERNATE MOUNTING IF DOOR CANOPEN BEYOND LIMITS SHOWN FOR STANDARD MOUNTINGDIM.ADIM.BDIM.AREVEALDEPTHARMTYPEMAX. DOOROPENINGMAX. DOOROPENINGDIM. "B"REGULARARM NOHOLDERSTANDARD7"12-1/8"5"10-1/8""A"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLATHEAD MACHINE SCREWS2"1-1/4"1RIGHT HAND DOOR SHOWN. LEFT HANDDOOR OPPOSITE.0" TO 2"9-5/16"“OZ” ARM2-1/8" TO 5"10-1/8"“OZA” ARM5-1/8" TO 5"10-15/16"THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.1"DRILL & TAP AND USE SCREWS PROVIDED OR USE MORTISENUTS WHEN REQUIRED.ALTERNATE MOUNTING ISRECOMMENDED FOR ADACOMPLIANT DOORSCL OF HINGE PIVOT:BUTTS, OFFSET PIVOTS,SWING CLEAR, CENTER HUNGOR INVISIBLE HINGES5/8"FRAMETOPOFDOOR10-3/8"#12 X 1-1/2" WOOD SCREWSOR #12-24 X 5/8 FLAT HEADMACHINE SCREW10-3/8"3-5/8"7/8"2“O” ARM1LEFT HAND DOOR SHOWN, RIGHTHAND DOOR OPPOSITE.2THESE DIMENSIONS MAYBE REDUCED TO 3/8"MIN. IF RAIL ON TOP CASING IS NARROW ORLOW CEILING CONDITION EXISTS. CLOSERFOOT SHOULD BE MOVED ACCORDINGLY.13THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.2DIM.ALTERNATE281 PARALLEL ARM APPLICATION INSTRUCTIONS4-1/2"10-1/2"HINGE PIVOT:BUTT, OFFSET PIVOTS, SWING CLEAR,CENTERHUNG OR INVISIBLE HINGES2-1/2"1-1/4"1/2"7-5/8"DOORLEFT HAND DOOR SHOWN. RIGHT HANDDOOR DIMENSION OPPOSITE.7/8"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.TOP VIEW#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWSDO NOT USE THIS MOUNTING FOR“SWING CLEAR” HINGES.5/16"DIM. B3THIS DIMENSION IS TAKEN FROM HINGEEDGE OF DOOR FOR INVISIBLE HINGES.4MAY BE REDUCED BY 1/2" TO AVOIDDOOR TRIM.DIM. ASTOPCL OF BRACKET1"DIM."A"USE MOUNTING BRACKETAS DRILL THRU TEMPLATETOP OFDOORUSE MOUNTING BRACKETAS A DRILL-THRU TEMPLATE1-5/8"ATOP OFDOOR3"DRILL & TAP AND USE SCREWS PROVIDED OR USEMORTISE NUTS WHEN REQUIRED.2"#12 x 1-1/2 WOOD SCREWSOR #12-24 x 5/8 FLAT HEADMACHINE SCREWS1"CL OF PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.DIM.B1-5/8"10-3/8"REMOVE BACKING FROM SELF ADHESIVE TAPE ANDUSE BRACKET AS DRILL THROUGH TEMPLATE.HINGEADIM.AINSTALL MOUNTING BRACKET WITH ARROW POINTING DOWN FOR BOTH RH & LH DOORS ANDINSTALL CLOSER WITH SPRING ADJUSTMENT SCREW AWAY FROM HINGE.BATTACH FOOT TO DOOR WITHPIVOT AWAY FROM HINGE.ACL OF HINGE PIVOTINSTALL MOUNTING BRACKET WITH ARROW POINTING UP FOR BOTH RH & LH DOORSAND INSTALL CLOSER WITH SPRING ADJUSTING SCREW TOWARDS HINGE.BATTACH FOOT BRACKET TO FRAME STOP.RIGHT HANDDOOR SHOWNRIGHT HANDDOOR SHOWNCRIGHT HAND DOOR SHOWN (LEFT HAND DOOR OPPOSITE)PIVOTCP3 OR P3ABRACKETINSTALL MAIN ARM TO SPINDLE AND SECURE WITH SCREW AND WASHER AS SHOWN.INSERT ROD END INTO MAIN ARM AND TIGHTEN ARM SCREW.(SARGENT#590 SHOWN)P4 OR P4ABRACKETINDEX MARKON SPINDLEMAIN ARMLEFT HANDDOOR54OPTIONAL ARMS FOR MOUNTING. SEE DATASHEET ENCLOSED.5MAINARM42311ROD2ARMSCREWINDEX MARKON SPINDLERIGHT HANDDOOR35MAINARMINDEXMARKONSPINDLE42CRIGHT HANDDOOR SHOWNATTACH ARM WITH INDEX MARK ON SPINDLE ALIGNED AS SHOWN. SECURE WITH SCREW ANDWASHER. INSERT ROD END INTO SWIVEL ARM AND TIGHTEN ARM SCREW AS SHOWN BELOW.31BATTACH FOOT TO FRAME WITH PIVOTAWAY FROM HINGE.POSITION OFMAIN ARM WHENASSEMBLINGTO SPINDLEFOR FLUSH FRAMEAND DOOR CONDITIONSSWIVEL ARMCAUTION: DOOR CLOSER WILL NOT OPERATEPROPERLY IF MAIN ARM IS NOT INDEXED CORRECTLY.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E2Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E3FOR USE WITH OVERHEADDOOR HOLDERSP4A BRACKET IS USEDWITH OVERHEAD HOLDERSCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E4
FINAL ADJUSTMENT AND REGULATING PROCEDUREDELAYEDACTIONVALVE(OPTIONAL)1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODYAND FOOT ON DOOR AND FRAME.BACKCHECKVALVEDELAYED ACTIONRANGE1/4" SPRING POWERADJUSTMENT SCREWCLOSINGSPEED VALVEBREGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISETO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOORMOVEMENT.FASTER( )DFOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THATSHOWN FOR MOUNTING THE CLOSER BODY.BREGULATING BACKCHECKSARGENT 1430SERIES CLOSERSHOWN. (OTHERSERIES SIMILAR)SEE NOTE #1 BELOW FOR DIMENSIONINFORMATION. IF A DIMENSION LESS THAN7/8" IS USED. THE DOOR STOP MUST BE CUTTO CLEAR THE MORTISE NUT HEAD OR THEMORTISE NUT HEAD MUST BE RECESSED.(SEE ENLARGED VIEW "Y")CLOSER MOUNTED ONHINGE SIDE OF DOORE NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREWFROM FACTORY SETTING (USE CHART AS GUIDE ONLY)281INTERIOR DOORSAPPROXIMATEEXTERIOR DOORSDOOR WEIGHT (POUNDS)FACTORY SET801101-5 CW1151-5 CCW1305-8 CW1501558-13 CWFACTORY SET1651701-5 CW13-15 CW180UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.NOTE: FOR 08 AND OLC TYPE ARMS MOUNTINGSEE DATA SHEETS ENCLOSEDDOOR STOPMORTISE NUT HEADDOORDRILL 3/8" DIA.HOLE FOR MORTISENUT BODY.DRILL 1/4" DIA. HOLEFOR MOUNTING SCREWS*ADJUST SPRING POWER ACCORDING TO CHART TOP JAMBAPPLICATION(TYPE 25-O, 25-OZAND 25-OZA ARMS)MOVE FOOTPIVOT TO HOLENEAREST HINGE DOOR WIDTH(INCHES)243032364042444648OVER 48USEPAGE 2FRAMEADJUSTING FOOT FOR ADDITIONAL CLOSING POWER(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)HINGE EDGE OF DOORTURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTERCLOCKWISE TO SPEED UP DOOR MOVEMENTSTANDARD & TOP JAMB APPLICATIONSSTANDARD APPLICATION(TYPE 25-O ARM)4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTSARE TIGHTENED.LATCHINGSPEED RANGECOVER“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGHDELAYED ACTION RANGE1BACKCHECKRANGETO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVECLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASECHECKING.CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT ISDAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.NEVER USE BACKCHECK AS A DOOR STOP.ALWAYS USE A DOOR STOP TO STOP THE DOOR.SLOWER(–)281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.CLOSING SPEEDRANGELATCHINGSPEEDVALVEAMODEL 281 POWERGLIDE SERIESINSTRUCTIONS FOR INSTALLING SARGENT DOORCLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)USING MORTISE NUTS WITH SARGENT DOOR TER CLOCKWISE(CCW)1/4" ALLEN SPRING POWERADJUSTING SCREWSARGENT 351 SERIES SHOWNLEFTHAND DOOR1/8"SHORTEN MORTISENUT BODY TOTHIS LENGTH5/8" DIA. HOLESTOP (PUSH) SIDECLOSER MOUNTED ON FRAMEON STOP SIDE OF DOORFRAMEINSTALL COVER WITH TWO SCREWS AS SHOWN.PULLHINGE SIDEPULLHINGE SIDERIGHTHAND DOORSTOP (PUSH) SIDEUSEPAGE 3DOORSTOPPARALLEL APPLICATION ONLYDOOR351 DOOR CLOSER SHOWN(TRACK ASSEMBLYMOUNTING IS SIMILAR)1/4" DIA.DRILLED HOLE#12-24 THREADMORTISE NUT9/16"DIA.MORTISE NUTHEAD3/8" DIA. HOLEPARALLEL ARMAPPLICATION(TYPE 25-P9)VIEW "Y"7/64"USEPAGE 41-11/16" FOR 1-3/4" THICK DOOR1-5/16" FOR 1-3/8" THICK DOOR(SEE NOTE #4 FOR 2-1/4" THICK DOORS)INSERT IS REMOVABLE.PLACE IN UNUSED OPENING.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E5CLOSER MOUNTED ONSTOP SIDE OF DOORCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E6DOOR WIDTH(INCHES)243032364042444648OVER 48NUMBER OF TURNS OF SPRING POWER ADJUSTING NUTFROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORSAPPROXIMATE281DOOR WEIGHT (POUNDS)EXTERIOR DOORS802-7 CW1101157-11 CW1-5 CCW130150FACTORY SET11-15 CW15516517015-17 CW1-8 CW180UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGSARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNINGSPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREWCOUNTERCLOCKWISE.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E1
FINAL ADJUSTMENT AND REGULATING PROCEDUREDELAYEDACTIONVALVE(OPTIONAL)1. SEE INSTRUCTIONS OR DATA SHEET PACKED WITH DOOR CLOSER FOR DIMENSIONS LOCATING THE CLOSER BODYAND FOOT ON DOOR AND FRAME.BACKCHECKVALVEDELAYED ACTIONRANGE1/4" SPRING POWERADJUSTMENT SCREWCLOSINGSPEED VALVEBREGULATING DOOR SPEED AND LATCHING SPEED AS NEEDED.USE HEX SOCKET (1/8" ALLEN) WRENCH AND TURN VALVES CLOCKWISETO SLOW DOWN OR COUNTER CLOCKWISE TO SPEED UP DOORMOVEMENT.FASTER( )DFOR MODELS WITH OPTIONAL DELAYED ACTION FEATURE3. FOR TOP JAMB AND CORNER BRACKET APPLICATIONS: THE DOOR CLOSER FOOT WILL BE ATTACHED TO THE DOOR IN A MANNER SIMILAR TO THATSHOWN FOR MOUNTING THE CLOSER BODY.BREGULATING BACKCHECKSARGENT 1430SERIES CLOSERSHOWN. (OTHERSERIES SIMILAR)SEE NOTE #1 BELOW FOR DIMENSIONINFORMATION. IF A DIMENSION LESS THAN7/8" IS USED. THE DOOR STOP MUST BE CUTTO CLEAR THE MORTISE NUT HEAD OR THEMORTISE NUT HEAD MUST BE RECESSED.(SEE ENLARGED VIEW "Y")CLOSER MOUNTED ONHINGE SIDE OF DOORE NUMBER OF TURNS OF SPRING POWER ADJUSTING SCREWFROM FACTORY SETTING (USE CHART AS GUIDE ONLY)281INTERIOR DOORSAPPROXIMATEEXTERIOR DOORSDOOR WEIGHT (POUNDS)FACTORY SET801101-5 CW1151-5 CCW1305-8 CW1501558-13 CWFACTORY SET1651701-5 CW13-15 CW180UP TO 19 CW AS REQ. 5 CW AND UP AS REQ.NOTE: FOR 08 AND OLC TYPE ARMS MOUNTINGSEE DATA SHEETS ENCLOSEDDOOR STOPMORTISE NUT HEADDOORDRILL 3/8" DIA.HOLE FOR MORTISENUT BODY.DRILL 1/4" DIA. HOLEFOR MOUNTING SCREWS*ADJUST SPRING POWER ACCORDING TO CHART TOP JAMBAPPLICATION(TYPE 25-O, 25-OZAND 25-OZA ARMS)MOVE FOOTPIVOT TO HOLENEAREST HINGE DOOR WIDTH(INCHES)243032364042444648OVER 48USEPAGE 2FRAMEADJUSTING FOOT FOR ADDITIONAL CLOSING POWER(FOR STANDARD AND TOP JAMB APPLICATIONS ONLY)HINGE EDGE OF DOORTURN VALVE CLOCKWISE TO SLOW DOWN OR COUNTERCLOCKWISE TO SPEED UP DOOR MOVEMENTSTANDARD & TOP JAMB APPLICATIONSSTANDARD APPLICATION(TYPE 25-O ARM)4. FOR DOORS 2-1/4" THICK: MORTISE NUT SHOWN FOR 1-3/4" THICK DOORS WILL BE FURNISHED ALONG WITH APPORPRIATE LENGTH THRU-BOLTS.DOOR CONSTRUCTION MUST PROVIDE A BRIDGE TYPE REINFORCEMENT TO PREVENT THE DOOR RAIL FROM COLLAPSING WHEN THRU-BOLTSARE TIGHTENED.LATCHINGSPEED RANGECOVER“DELAYED ACTION” PROVIDES SLOW DOOR CLOSING THROUGHDELAYED ACTION RANGE1BACKCHECKRANGETO REGULATE THE INTENSITY OF BACKCHECK ACTION TURN VALVECLOCKWISE TO INCREASE OR COUNTER CLOCKWISE TO DECREASECHECKING.CAUTION: SET VALVE FOR SLIGHT CUSHIONING EFFECT. IT ISDAMAGING TO THE CLOSER IF THE CHECKING ACTION IS TOO ABRUPT.NEVER USE BACKCHECK AS A DOOR STOP.ALWAYS USE A DOOR STOP TO STOP THE DOOR.SLOWER(–)281 SERIES NON SIZED ADJUSTABLE SIZES 1 THRU 6CAUTION: FAILURE TO INSTALL OR ADJUST PROPERLY MAY RESULT IN INJURY OR DAMAGE.FOR ASSISTANCE, CALL SARGENT AT 1-800-727-5477.2. MORTISE NUT SHOWN IS DESIGNED FOR AN UNREINFORCED METAL DOOR.CLOSING SPEEDRANGELATCHINGSPEEDVALVEAMODEL 281 POWERGLIDE SERIESINSTRUCTIONS FOR INSTALLING SARGENT DOORCLOSERS WITH REGULAR ARMS (WITHOUT HOLDER)USING MORTISE NUTS WITH SARGENT DOOR TER CLOCKWISE(CCW)1/4" ALLEN SPRING POWERADJUSTING SCREWSARGENT 351 SERIES SHOWNLEFTHAND DOOR1/8"SHORTEN MORTISENUT BODY TOTHIS LENGTH5/8" DIA. HOLESTOP (PUSH) SIDECLOSER MOUNTED ON FRAMEON STOP SIDE OF DOORFRAMEINSTALL COVER WITH TWO SCREWS AS SHOWN.PULLHINGE SIDEPULLHINGE SIDERIGHTHAND DOORSTOP (PUSH) SIDEUSEPAGE 3DOORSTOPPARALLEL APPLICATION ONLYDOOR351 DOOR CLOSER SHOWN(TRACK ASSEMBLYMOUNTING IS SIMILAR)1/4" DIA.DRILLED HOLE#12-24 THREADMORTISE NUT9/16"DIA.MORTISE NUTHEAD3/8" DIA. HOLEPARALLEL ARMAPPLICATION(TYPE 25-P9)VIEW "Y"7/64"USEPAGE 41-11/16" FOR 1-3/4" THICK DOOR1-5/16" FOR 1-3/8" THICK DOOR(SEE NOTE #4 FOR 2-1/4" THICK DOORS)INSERT IS REMOVABLE.PLACE IN UNUSED OPENING.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E5CLOSER MOUNTED ONSTOP SIDE OF DOORCopyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E6DOOR WIDTH(INCHES)243032364042444648OVER 48NUMBER OF TURNS OF SPRING POWER ADJUSTING NUTFROM FACTORY SETTING (USE CHART AS GUIDE ONLY) INTERIOR DOORSAPPROXIMATE281DOOR WEIGHT (POUNDS)EXTERIOR DOORS802-7 CW1101157-11 CW1-5 CCW130150FACTORY SET11-15 CW15516517015-17 CW1-8 CW180UP TO 19 CW AS REQ. 8 CW AND UP AS REQ.*IF INTERIOR DOORS DO NOT HAVE TO COMPLY WITH ADA REQUIREMENTS, EXTERIOR DOOR SETTINGSARE RECOMMENDED. WHERE STRONG DRAFTS EXIST, INCREASE SPRING POWER AS NEEDED BY TURNINGSPRING ADJUSTMENT SCREW CLOCKWISE. IF NECESSARY, REDUCE SPRING POWER BY TURNING SCREWCOUNTERCLOCKWISE.Copyright 2001, 2003, 2005-2008, Sargent Manufacturing Company, an ASSA ABLOY Group company.All rights reserved. Reproduction in whole or in part without the express written permission ofSargent Manufacturing Company is prohibited.A7278E1
using mortise nuts with sargent door closer frame door cover sargent 1430 series closer s hown. ( t er series similar) door stop mor tis enu h ad drill 3/8" dia. hole for mortise nut body. drill 1/4" dia. hole f o rm u nti g sc w 1. see instructions or data sheet packed with door closer for dimensions locating the closer body and fot r me.
