Transcription
DATA SHEETForm 0252-220705PAGE 1G4 DIGITAL AC OUTPUT MODULESFeatures 4000 volts optical isolation (transient)Built-in LED status indicatorLogic levels of 5, 15, and 24 VDCRemovable fuseCurrent rating: 3 amps at 45 CUL Motor Load rating: 1.5 ampsAbility to withstand one-cycle surge of 80 ampsOperating temperature: -30 C to 70 CG4OAC5A and G4OAC5AMAModulesDESCRIPTIONOpto 22’s G4 AC output modules are used to control or switch ACloads. Each module provides up to 4000 volts of optical isolation(transient) between field outputs and the control side of the circuit,and each features zero voltage turn-on and zero current turn-off.All AC output modules are equivalent to single-pole, single-throw,normally open contacts (Form A, SPST-NO) except the G4OAC5A5,which is equivalent to a single-pole, single-throw, normally closedcontact (Form B, SPST-NC).Each module is equipped with a 4 amp fast-blow fuse. The fusebreaking capacity is 40 amps at 250 VAC. Current should be limited toprevent the short circuit current from exceeding the rated breakingcapacity of the fuse.Typical applications for AC output modules include switching loadssuch as AC relays, solenoids, motor starters, heaters, lamps, andindicators.Part NumbersPartDescriptionG4OAC5*G4 AC Output 12–140 VAC, 5 VDC LogicG4OAC5FMG4 AC Output 12–140 VAC, 5 VDC Logic, Factory Mutual ApprovedG4OAC5A*G4 AC Output 24–280 VAC, 5 VDC LogicG4OAC5AFMG4 AC Output 24–280 VAC, 5 VDC Logic, Factory Mutual ApprovedThe G4OAC5MA and the G4OAC5AMA are special modules featuring amanual-on/manual-off/automatic switch, ideal for diagnostic testingof control applications.G4OAC5A5*G4 AC Output 24–280 VAC, 5 VDC Logic NCG4OAC5A5FMG4 AC Output 24–280 VAC, 5 VDC Logic NC,Factory Mutual ApprovedPart numbers ending in FM are Factory Mutual approved.G4OAC5MA*G4 AC Output 12–140 VAC, 5 VDC Logic WithManual/Auto SwitchCompatible with Raspberry PiG4OAC5AMA*G4 AC Output 24–280 VAC, 5 VDC Logic WithManual/Auto SwitchG4OAC15G4 AC Output 12–140 VAC, 15 VDC LogicThe following G4 digital AC output modules can be used with theDigital I/O Carrier Board for Raspberry Pi (part number OPTO-P1-40P)to monitor and control industrial devices with your Raspberry Pi: G4OAC5 G4OAC5A G4OAC5A5 G4OAC5MA G4OAC5AMAG4OAC15AG4 AC Output 24–280 VAC, 15 VDC LogicG4OAC24G4 AC Output 12–140 VAC, 24 VDC LogicG4OAC24AG4 AC Output 24–280 VAC, 24 VDC Logic* Compatible with Raspberry PiRaspberry Pi is a trademark of the Raspberry Pi Foundation.OPTO 22 800-321-6786 1-951-695-3000 www.opto22.com sales@opto22.com 2001–2022 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
DATA SHEETForm 0252-220705PAGE nal line voltageVAC120120/240120/240120120/240Output voltage y feature———Normally closedDiagnosticswitchDiagnosticswitchCurrent rating:At 45 C ambientAt 70 C ambientAA3232323232UL Motor Load 150040001500mARMS51.25/2.51.25/2.551.25/2.5Nominal logic voltageVDC55555Logic voltage rangeVDC4–84–84–84–84–8Logic pickup voltageVDC44444Logic dropout voltageVDC11111Logic input current atnominal logic voltagemA1212121212ohms220220220220220A peak8080808080Isolation input-tooutput (transient):1 ms1 minuteOff-state leakage atnominal voltage (60 Hz)Control resistance(Rc in schematic)One-cycle surgevoltsTurn-on time @ 60 HzmillisecondsTurn-off time @ 60 Hzmilliseconds 8.3*** 8.3**** 8.3*** 8.3**** 8.3*** 8.3**** 8.3*** 8.3**** 8.3*** 8.3****Peak repetitive voltageVAC500500500500500Minimum load currentmA2020202020Output voltage dropmaximum peakV1.61.61.61.61.6Operating ed for0.5 powerfactor loadsnubbed for0.5 powerfactor loadsnubbed for0.5 powerfactor loadsnubbed for0.5 powerfactor loadsnubbed for0.5 powerfactor loadTemperatureOperating:Storage: C C-30 to 70-30 to 85-30 to 70-30 to 85-30 to 70-30 to 85-30 to 70-30 to 85-30 to 70-30 to 85UL, CE, CSA;UKCAUL, CE, CSA;UKCACE, CSA; UKCAUL, CE, CSA;UKCAUL, CE, CSA,RoHS; UKCAdV/dT-off-stateAgency Approvals* Compatible with Raspberry Pi** Part numbers ending in FM are Factory Mutual approved.*** One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.**** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.OPTO 22 800-321-6786 1-951-695-3000 www.opto22.com sales@opto22.com 2001–2022 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
DATA SHEETForm 0252-220705PAGE 3SPECIFICATIONS A***Nominal line voltageVAC120120/240120120/240Output voltage rangeVAC12–14024–28012–14024–280Key feature—————Current rating:At 45 C ambientAt 70 C ambientAA32323232UL Motor Load RatingA1.51.51.51.5Isolation input-to-output (transient):1 ms1 te leakage at nominal voltage(60 Hz)mARMS51.25/2.551.25/2.5Logic voltage rangeVDC10.5–1610.5–1619.5–3219.5–32Logic pickup voltageVDC10.510.519.519.5Logic dropout voltageVDC1111mA15151818ohms1K1K2.2 K2.2 KA peak80808080Turn-on time @ 60 Hzmicroseconds 8.3* 8.3* 8.3* 8.3*Turn-off time @ 60 Hzmicroseconds 8.3** 8.3** 8.3** 8.3**Peak repetitive voltageVAC500500500500Minimum load currentmA20202020Logic input current at nominal logicvoltageControl resistance(Rc in schematic)One-cycle surgeOutput voltage drop maximum peakV1.61.61.61.6Operating nd200200200200dV/dT-commutating--snubbed for 0.5power factor loadsnubbed for 0.5power factor loadsnubbed for 0.5power factor loadsnubbed for 0.5power factor loadTemperatureOperating:Storage: C C-30 to 70-30 to 85-30 to 70-30 to 85-30 to 70-30 to 85-30 to 70-30 to 85UL, CE, CSA;UKCAG4OUL, CE, CSA;UKCAOUL, CE, CSA;UKCAG4UL, CE, CSA;UKCAdV/dT-off-stateAgency Approvals* One-half cycle maximum. Module turns on at the zero volt crossing of the AC sine wave.** One-half cycle maximum. Module turns off at the zero current crossing of the AC sine wave.*** Not for use with Opto 22 brains.OPTO 22 800-321-6786 1-951-695-3000 www.opto22.com sales@opto22.com 2001–2022 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
DATA SHEETForm 0252-220705PAGE 4DIMENSIONSSCHEMATICSOPTO 22 800-321-6786 1-951-695-3000 www.opto22.com sales@opto22.com 2001–2022 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.
More about Opto 22PRODUCTSgroov EPIC SoftwareOpto 22 develops and manufactures reliable, easy-to-use, openstandards-based hardware and softwareproducts. Industrial automation, processcontrol, remote monitoring, data acquisition,and industrial internet of things (IIoT)applications worldwide all rely on Opto 22.The groov EPIC processor comes ready to run the software you need: Programming: Choose flowchart-basedPAC Control, CODESYS DevelopmentSystem for IEC61131-3 compliantprograms, or secure shell access (SSH) tothe Linux OS for custom applications Node-RED for creating simple IIoT logicflows from pre-built nodes Efficient MQTT data communicationswith string or Sparkplug data formats Multiple OPC UA server options HMI: groov View to build your own HMIviewable on touchscreen, PCs, andmobile devices; PAC Display for aWindows HMI; Node-RED dashboard UI Ignition or Ignition Edge from Inductive Automation (requireslicense purchase) with OPC-UA drivers to Allen-Bradley ,Siemens , and other control systems, and MQTT communicationsgroov RIO groov RIO edge I/O offers a single, compact,PoE-powered industrial package with webbased configuration and IIoT software builtin, support for multiple OT and IT protocols,and security features like a device firewall,data encryption, and user account control.Standing alone, groov RIO connects to sensors, equipment, and legacysystems, collecting and securely publishing data from field to cloud.Choose a universal I/O model with thousands of possible field I/Oconfigurations, with or without Ignition from Inductive Automation ,or a RIO EMU energy monitoring unit that reports 64 energy datavalues from 3-phase loads up to 600 VAC, Delta or Wye.You can also use groov RIO with a Modbus/TCP master or as remoteI/O for a groov EPIC system.groov EPIC SystemOpto 22’s groov Edge Programmable Industrial Controller (EPIC)system gives you industrially hardened control with a flexible Linux based processor with gateway functions, guaranteed-for-life I/O, andsoftware for your automation and IIoT applications.groov EPIC ProcessorThe heart of the system is the groov EPIC processor. It handles a widerange of digital, analog, and serial functions for data collection,remote monitoring, process control, and discrete and hybridmanufacturing.In addition, the EPIC provides secure data communications amongphysical assets, control systems, software applications, and onlineservices, both on premises and in the cloud. No industrial PC needed.Configuring and troubleshooting I/O and networking is easier withthe EPIC’s integrated high-resolution color touchscreen. Authorizedusers can manage the system locally on the touchscreen, on amonitor connected via the HDMI or USB ports, or on a PC or mobiledevice with a web browser.groov EPIC I/Ogroov I/O connects locally to sensors and equipment. Modules have aspring-clamp terminal strip, integrated wireway, swing-away cover,and LEDs indicating module health and discrete channel status. groovI/O is hot swappable, UL Hazardous Locations approved, and ATEXcompliant.OPTO 22 www.opto22.com43044 Business Park Dr. Temecula, CA 92590-3614Older productsFrom solid state relays, to world-famous G4 and SNAP I/O, to SNAPPAC controllers, older Opto 22 products are still supported andworking hard at thousands of installations worldwide. You can counton us for the reliability and service you expect, now and in the future.QUALITYFounded in 1974, Opto 22 has established a worldwide reputation forhigh-quality products. All are made in the U.S.A. at our manufacturingfacility in Temecula, California.Because we test each product twice before it leaves our factory ratherthan testing a sample of each batch, we can afford to guarantee mostsolid-state relays and optically isolated I/O modules for life.FREE PRODUCT SUPPORTOpto 22’s California-based Product Support Group offers freetechnical support for Opto 22 products from engineers with decadesof training and experience. Support is available in English and Spanishby phone or email, Monday–Friday, 7 a.m. to 5 p.m. PST.Support is always available on our website, including free onlinetraining at OptoU, how-to videos, user’s guides, the Opto 22KnowledgeBase, and OptoForums.PURCHASING OPTO 22 PRODUCTSOpto 22 products are sold directly and through a worldwide networkof distributors, partners, and system integrators. For more information,contact Opto 22 headquarters at 800-321-6786 (toll-free in the U.S.and Canada) or 1-951-695-3000, or visit our website atwww.opto22.com.SALES sales@opto22.com800-321-6786 1-951-695-3000SUPPORT support@opto22.com800-835-6786 1-951-695-3080 2001–2022 Opto 22. All rights reserved. Dimensions and specifications are subject to change. Brand or product names used herein are trademarks or registered trademarks of their respective companies or organizations.Form 1335-220705
Logic voltage range VDC 10.5-16 10.5-16 19.5-32 19.5-32 Logic pickup voltage VDC 10.5 10.5 19.5 19.5 Logic dropout voltage VDC 1 1 1 1 Logic input current at nominal logic . data encryption, and user account control. Standing alone, groov RIO connects to sensors, equipment, and legacy
