Transcription
Bergstrom IndustriesJanuary 15, 2020Turbo Poly SealApplication GuidePage 1
Bergstrom IndustriesJanuary 15, 2020Flashing detail to avent pipeAlways use gloves when workingwith chemicalsPage 2
Bergstrom IndustriesJanuary 15, 2020Make sure all surfaces all cleanfrom grease and dust usingLacquer Thinners Sand smooth surfaces with 120 grid sandpaper to create a rough surfacePage 3
Bergstrom IndustriesJanuary 15, 2020Tape off the area where Turbo PolySeal will be applied tooPage 4
Bergstrom IndustriesJanuary 15, 2020Measure and cut the correct size ofPoly Fleece Sand the PVC pipe or any other surface tocreate a rough surface for better bonding Overlap each end of the polyester fleece withapproximately one inchPage 5
Bergstrom IndustriesJanuary 15, 2020Cut tabs approximately every 3/4”wide by 1 1/2” deep Space the tabs evenly The tabs should be around 3/4’ to 1” wideand approximately 11/2” to 2” longPage 6
Bergstrom IndustriesJanuary 15, 2020Dry fit the fleece with the tabs cut Mark the top of the fleece and mask offapproximately 1” above the fleecePage 7
Bergstrom IndustriesJanuary 15, 2020Use a paint brush to apply a coat ofTurbo Poly Seal Apply a thick coat of Turbo Poly Seal to bothsurfaces - pipe and roofing surfacePage 8
Bergstrom IndustriesJanuary 15, 2020Make sure to cover all areas insidethe masking tapePage 9
Bergstrom IndustriesJanuary 15, 2020Install the pre-cut fleece with tabsto the bottom When installing the fleece, make sure the tabsare lying flat.Page 10
Bergstrom IndustriesJanuary 15, 2020Dab the fleece with the brush intothe layer of Turbo Poly Seal coating Use the brush to push the fleece into thecorner so there is no void behind the fleece Dab the fleece to ensure there is no airtrappedPage 11
Bergstrom IndustriesJanuary 15, 2020Apply a coat of Turbo Poly Sealover the Fleece Paint a thick coat so you can’t see the textureof the fleece You can always come back after it is cured andapply another coating id necessaryPage 12
Bergstrom IndustriesJanuary 15, 2020Remove the masking Tape Remove the masking tape immediately afterapplying the last coatPage 13
Bergstrom IndustriesJanuary 15, 2020Good Job The Turbo Poly Seal will cure over 24 hoursbut it can rain within 20 minutes of applicationand it will be good Turbo Poly Seal can be applied intemperatures of 20 F and abovePage 14
Bergstrom IndustriesJanuary 15, 2020 It is good practice to apply a protectivecoating like Aluminum asphalt (Silver Coating) orany urethane or oil based paint after the TurboPoly Seal is curedPage 15
Bergstrom IndustriesJanuary 15, 2020Transition to metalor anothermembrane:Make sure the metal flashing issecured by nailing itPage 16
Bergstrom IndustriesJanuary 15, 2020Use sanding block or sand paper toroughen up surface of metalPage 17
Bergstrom IndustriesJanuary 15, 2020Use wire brush to get into tightareasPage 18
Bergstrom IndustriesJanuary 15, 2020Wipe all surfaces clean using a ragand Lacquer ThinnersPage 19
Bergstrom IndustriesJanuary 15, 2020Mask off the area where the TurboPoly Seal will be appliedPage 20
Bergstrom IndustriesJanuary 15, 2020Apply a coat of Turbo Poly Seal inthe masked off areaPage 21
Bergstrom IndustriesJanuary 15, 2020Install the Polyester Fleece and dabit with a brush to get it to stick tothe Turbo Poly SealPage 22
Bergstrom IndustriesJanuary 15, 2020Apply a Top coat of Turbo Poly Sealover the fleecePage 23
Bergstrom IndustriesJanuary 15, 2020Remove the masking tapePage 24
Bergstrom IndustriesJanuary 15, 2020Job well donePage 25
Bergstrom Industries January 15, 2020 Turbo Poly Seal Application Guide Page 1. Bergstrom Industries January 15, 2020 Flashing detail to a vent pipe Always use gloves when working with chemicals Page 2. Bergstrom Industries January 15, 2020 Make sure all surfaces all clean
