Transcription
D001865710ADigital Mixing ConsoleOWNER’S MANUAL
IMPORTANT SAFETY PRECAUTIONSFor U.S.AFor the consumers in EuropeTO THE USERThis equipment has been tested and found tocomply with the limits for a Class A digital device,pursuant to Part 15 of the FCC Rules. Theselimits are designed to provide reasonableprotection against harmful interference when theequipment is operated in a commercialenvironment. This equipment generates, uses,and can radiate radio frequency energy and, ifnot installed and used in accordance with theinstruction manual, may cause harmfulinterference to radio communications.Operation of this equipment in a residental areais likely to cause harmful interference in whichcase the user will be required to correct theinterference at his own expense.CAUTIONChanges or modifications to this equipment notexpressly approved by TEAC CORPORATIONfor compliance could void the user’s authority tooperate this equipment.ÜÿŸWARNINGThis is a Class A product. In a domestic environment, thisproduct may cause radio interference in which case theuser may be required to take adequate measures.Pour les utilisateurs en EuropeAVERTISSEMENTIl s’agit d’un produit de Classe A. Dans un environnementdomestique, cet appareil peut provoquer desinterférences radio, dans ce cas l’utilisateur peut êtreamené à prendre des mesures appropriées.Für Kunden in EuropaWarnungDies is eine Einrichtung, welche die Funk-Entstörungnach Klasse A besitzt. Diese Einrichtung kann imWohnbereich Funkstörungen versursachen ; in diesemFall kann vom Betrieber verlang werden, angemesseneMaßnahmen durchzuführen und dafür aufzukommen.CE Marking Informationa) Applicable electromagnetic environment: E4b) Peak inrush current: 8 ACAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVECOVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert theuser to the presence of uninsulated “dangerous voltage” within the product’s enclosure thatmay be of sufficient magnitude to constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert the user to the presenceof important operating and maintenance (servicing) instructions in the literature accompanyingthe appliance.This appliance has a serial numberlocated on the rear panel. Please recordthe model number and serial number andretain them for your records.Model numberSerial numberWARNING: TO PREVENT FIRE OR SHOCKHAZARD, DO NOT EXPOSE THISAPPLIANCE TO RAIN OR MOISTURE.2 TASCAM DM-3200 Owner’s Manual
IMPORTANT SAFETY INSTRUCTIONS1234567Read these instructions.Keep these instructions.Heed all warnings.Follow all instructions.Do not use this apparatus near water.Clean only with dry cloth.Do not block any ventilation openings. Install inaccordance with the manufacturer’s instructions.8 Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus(including amplifiers) that produce heat.9 Do not defeat the safety purpose of the polarizedor grounding-type plug. A polarized plug hastwo blades with one wider than the other.Grounding type plug has two blades and a thirdgrounding prong. The wide blade or the thirdprong are provided for your safety. If the provided plug does not fit into your outlet, consultan electrician for replacement of the obsoleteoutlet.10 Protect the power cord from being walked on orpinched, particularly at plugs, conveniencereceptacles, and the point where they exit fromthe apparatus.11 Only use attachments/accessories specified bythe manufacturer.12 Use only with the cart, stand, tripod, bracket, ortable specified by the manufacturer or sold withthe apparatus. When a cart is used, use cautionwhen moving the cart/apparatus combination toavoid injury from tip-over.13 Unplug this apparatus during lightning storms orwhen unused for long periods of time.14 Refer all servicing to qualified service personnel. Servicing is required when the apparatus hasbeen damaged in any way, such as power-supplycord or plug is damaged, liquid has been spilledor objects have fallen into the apparatus, theapparatus has been exposed to rain or moisture,does not operate normally, or has been dropped. Do not expose this apparatus to drips orsplashes. Do not place any objects filled with liquids, suchas vases, on the apparatus. Do not install this apparatus in a confined spacesuch as a book case or similar unit. The apparatus draws nominal non-operatingpower from the AC outlet with its POWERswitch in the off position. The apparatus should be located close enough tothe AC outlet so that you can easily grasp thepower cord plug at any time. An apparatus with Class I construction shall beconnected to an AC outlet with a protectivegrounding connection.TASCAM DM-3200 Owner’s Manual 3
Contents1 – IntroductionComputer (DAW) integration . 9Other key points . 9Please read this manual . 9About the DM-3200 . 10Inputs . 10Channel modules . 10Channel destinations . 11Outputs . 11Effects . 11Unpacking the DM-3200 . 11About the manual . 12What’s in the manual . 121, “Introduction” (page 9) . 122, “Basic operational concepts” (page 16) . 123, “Connections” (page 38) . 124, “Routing & assignment” (page 46) . 125, “Channel modules” (page 59) . 126, “Effects” (page 81) . 127, “MIDI” (page 91) . 128, “Remote operation” (page 93) . 129, “Specifications” (page 102) . 12Notes and warnings . 12Special notes for touch-sensitive faders . 13Copyright, etc. . 13The features of the DM-3200 . 14Control section . 15Monitoring section . 15Module & layer control section . 15Encoder section . 15Modifier section . 15Library section and CF card slot . 15Machine control section . 15Analog input section . 152 – Basic operational conceptsSmart keys . 16What’s on the screen? . 16Jumping to commonly-used screens . 17Setting a USER screen . 17Fader layers . 18Special controls . 18The PODs . 18Encoders . 20Encoder mappings . 20Pan mode . 20Aux mode . 20GATE/DYN dynamics processor mode . 20EQ . 21SND AUX 1–2 . 21PAN AUX 1–2 . 21LVL BUSS . 21LVL AUX . 21LVL CH 1–16, 17–32, 33–48 . 21Reading the encoder indicators . 21Pan settings . 21EQ settings . 22Module levels and AUX sends . 23Dynamics settings . 23The FLIP key . 23Encoder behavior . 234 TASCAM DM-3200 Owner’s ManualCF cards .24Formatting a new card .24Shutting down the DM-3200 .25IMPORTANT CAUTION!!! .25How to shut down the DM-3200 .25Starting up the DM-3200 .25About projects and libraries .26Setting the date and time .27Creating a new project .27Using a template .27Managing projects .28Loading a project .28Copying a project .28Deleting a project .28Renaming a project . 28Saving project data .29Library management .30Using library banks .30Viewing library entries .31Recalling library entries .31Storing library entries .31Deleting library entries .31Library utilities .31Target parameters .31Source parameters .32Naming library entries .32Options .32SETUP screen .32UPPER BAR DISPLAY .33LOCATE DISPLAY mode .33ENCODER OPERATION mode .33LIBRARY DIRECT KEY OPERATION .33OL/STATUS LED TYPE .33FADER SENSITIVITY .33PREFERENCES .34Fader Auto MODULE Select .34CH SOLO Key Auto MODULE Select .34Select MODULE Return .34ST Link by SEL key .34SEL Key Follows Fader Layer Status .34Meter Follows SEL key .34Automation fader OFF .34Balance Level CENTER:0dB .34AUX Mute follows CH Mute .34Encoder Mode Follows Current Screen .34Current Screen Follows Encoder Mode .34BUSS PAN Follows ST PAN .34BUSS Link/BUSS PAN are Linked .35SOLO .35MODE SELECT .35SOLO LINK .35SOLO TYPE .35INPLACE SOLO DEFEAT .35Utilities .36UTILITY copying .36SWITCH utility .37Talkback .37Machine Control .37Other functions .37Polarity .37
Contents3 – ConnectionsAnalog connections .39Mic/line connections . 39Channel inserts .392 TR IN .39ASSIGNABLE RETURNS .39Analog outputs .40STEREO OUT .40ASSIGNABLE SENDS . 40Monitoring (CR OUTPUTS) .40Monitoring (STUDIO OUTPUTS) .40Digital connections .40Digital audio I/O .
TASCAM DM-3200 Owner’s Manual 3 IMPORTANT SAFETY INSTRUCTIONS 1 Read these instructions. 2 Keep these instructions. 3 Heed all warnings. 4 Follow all instructions. 5 Do not use this apparatus near water. 6 Clean only with dry cloth. 7 Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8 Do not install near any h eat sources such as radi-
