Transcription
GALAXYOWNER’S MANUAL& PARTS LISTThis equipment is intended for commercial use only.GALAXY HX-HRGALAXY AUTOMOTIVE 3100BX-EH & 3000VX-EHZF1202 REV 7/081753 Blake Avenue Los Angeles, CA 90031 (800) 338-EDIC, or in CA (323) 660-1635 Fax (323) 667-0144
BEFORE OPERATING THE MACHINERead the manual carefully and completely before attempting to operate the unit. This manual has importantinformation for the use and safe operation of the machine. Keep this manual handy at all times. This machinewill assure years of satisfactory service if operated and maintained according to recommendations in thismanual. If additional information is needed, please contact your local distributor or write to:EDIC1753 Blake AveLos Angeles, CA 90031-1006WARNING The machine was designed for use on carpet, floor and upholstery extraction applications as perinstructions and recommendations written in this manual. Any deviation from its proper use orpurpose and the consequential damage that may occur is the sole responsibility if the end user.Disconnect the power cord from the outlet before servicing. Do not leave machine connected to anelectrical outlet when unattended.Do not immerse or use this machine in standing water. Such use may cause electric shock.This equipment is not designed to handle or use combustible/volatile substances such as gasoline orkerosene, in, on, or near the machine. The use of such materials will cause extreme hazardouscondition.When using an extension cord, use only a 3-prong conductor grounding cord- 12 ga. wire or heavier.To avoid electric shock, do not expose the unit to rain. Store it indoors only.Do not use the machine for dry vacuuming.Use defoamer at all times to prevent damage to the vacuum motor(s).Do not use water in excess of 170ºF (76ºC).To prevent seal damage and chemical build-up to the pump system, run clean water through thesolution lines after each day’s use.Use only commercially available carpet cleaning solutions and defoamer intended for use withmachines of this type. Do not use dyes, bleaches, ammonia, or other additives. The use of powderedcleaning solution if not diluted properly may result in damage to the pump. If powdered chemicals areused, premix in a separate container before placing in the solution tank.Do not expose machine to freezing temperatures.All repairs must be done by an authorized EDIC repair station.Do not use replacement parts other than those specified on the parts list.For units with HEAT’N’RUN heater: Read and understand the HEAT’N’RUN owners manual before using the HEAT’N’RUN heater on yourGALAXY Extractor. Do not run heater dry. Water hookups must be in place and water flowing through the heater prior to turning it on. Failure to doso may cause internal component damage and will void warranty. Heater must be filled with water or water based solutions at all times when in use. Turn off the switch andunplug the heater from outlet when not in use. Do not use heater at more than 500 PSI. Do not immerse heater in water. To avoid explosion and / or fire, do not use solvents or any flammable liquid in heater.FAILURE TO COMPLY WITH THE ABOVE WARNING INSTRUCTIONS WILL VOID THEWARRANTYITEM 5556575859606162636465666768697071GALAXY 2000FX-HR (BASE) PARTS LISTPART 79-2DESCRIPTION#8 X .25 PAN HEADHOSE, 3 INSCREW CLAMP, 1.63-2.43 INVACUUM HOSE, 2 IN GRAY, WIRE, 22 IN LGLOCKNUT, 1-4 X 20, NYLON, SSINTERCOOLER, GALAXY, BLACKWASHER, FLAT, .25 INGROMMETSCREW, 10-32 X .375 GROUNDGROUND WIRE, GALAXYVACUUM, 135 IN 115 V 5.7 INHOSE CLAMP, 2 IN SLDPRTVACUUM HOSE, 2 IN GRAY, WIRE, 4 IN LGNUT, .25-20 HEXLOCK WASHER, 1-4 IN SPLITVAC PLATESCREW, 1-4 X 20 X 4.5 IN HEXLOCK WASHER, .25 IN., INTERNAL STARSCREW, 1-4 X 20 X 4.5 IN, FLAT HEAD, PHILIPSSOLUTION HOSE, .375, 100PSI, WIRE, 31 IN. LGSCREW CLAMP #6, .43 TO .875 INPOWER PRIME.25 MALE X .375 BARB, BRASS45 ELBOW, .25MP X .25FPVALVE, REGULATOR, 200PSI90 ELBOW, .25MP X .25FPHOSE ASSEMBLY, 13 IN X .25 HPGAUGE, 0-600 PSIWASHER, .56 X 1.5 X .05QD, 1-4 M X 1-4 FP, BRASSTEE, .25 FP, BRASSNIPPLE, .25 INWASHER, .5IN, FLAT90 ELBOW, .25NPT X .25 NPTSPACER, HEATER MOUNTING PLATEPLUG, 1.25 IN, BLACKHEX BOLT, 1-4 X 20 X 1.75 INHEATER MOUNTING PLATESCREW, #8 X 1 IN, PAN, BLACKHEATER, TUNNEL COVER, BLUE GRANITESTAUB, 12-3 SJTW YELLOWNYLON TIE, 11 IN BLACK#8 X .5 IN PAN, BLACK SMS, PHILIPSTIE HOLDER WITH GLUESTRAIN RELIEF, PIGTAILCOVER, SERIAL # LABELLABEL, SERIAL NUMBERCAP NUT, .5IN PUSH-ONWASHER, SHOULDER, NYLONWHEEL, 10 INAXLEBASEHEX BOLT, 1-4 X 20 X 1 INCASTER, 4 INPUMP, 500 PSI, 120VTERMINAL LUG, FEMALE, QD, .25 X .032, 16-14 AWG, FULLY INSULATEDWASHER, .187 ID, BACKUPBUSHING.375 M X .25 P BRASS.50 BARB X .25 MP, BRASSMALE PLUG, .25 IN, NYLONHOSE, .5 IN POLYWIRE PVC, 33 IN LGPULSE HOSE, PUMP-QD, 42 INNYLON TIE, 4 INPLATE, PUMP, GALAXY, FLATLABEL, CAUTION, MOTOR HOUSINGHOSE, .5 IN POLYWIRE, 30 INSTRAINER, INLINE, 5 INSOLUTION HOSE, .375, 100 PSI, WIRE, 27 IN LGVACUUM HOSE, 2 IN GRAY, WIRE, 7 IN LGGASKET, VAC MOTOR, GALAXYCLOSED END CNTR, 24212112421182121411121311111126
2000FX-HR BaseThe120V A/C and the 220V A/C models have beenoutfitted with the appropriate12-19-07grounded connectors. Make sure the machine is connected to a grounded outletGROUNDING INSTRUCTIONS123654ITEM the same configuration asPARThavingthe groundedNUMBER plug. No adapter should be used withDESCRIPTIONNO.thisAnymodification1 machine.C00297 #8X .25Pan Head to the connectors will void the warranty.789101112701436915681623 24 2520 21 2217763 64 6542261772127137121182919566672636 3534333231303729 28393840626144604342414546472159395857 56 5549521054537515049 482000FX-HR Base12-19-07QTY.12 J11863 Hose, 3 in13 J00639 Screw Clamp, 1.63 - 2.43in.3PREPARINGTHEHose,MACHINEGALAXYEQUIPMENT)4 J00618 Vacuum2in Grey,(ALLWire, 22in lg15 C00273 Locknut, 1-4 X 20, Nylon, SS166 F11178-BLKIntercooler,Galaxy,Black use only the correct EDIC high pressure, high heat wands & uphol1IMPORTANT:Forall Galaxyequipment,7 C00233 Washer, Flat, .25 in26sterytools. Theyare designed to deliver and maintain the correct gallons per minute (GPM), pressure (PSI)8 nattachedthe GALAXY pump system. Use of other manufacturer wands can cause over10 heatB11150GroundWire, toGalaxy211 G02522LVacuum, 135 toin, the115 pumpV, 5.7 insystem (including hose & fittings), lack of pressure and heat.2wettingof carpet,damage12 J00657 Hose Clamp, 2 inSLDPRT113 J00618 Vacuum Hose, 2 in Grey, Wire, 4 in lg11.14PourcleansolutionC00261Nut,.25-20, intoHex the solution tank.10C00254Lock hoseWasher,1-4in2.15SlidevacuumontotheSplitblack hose adapter (located at the back of the machine) and the wand or116 D11134 Vac Plate1tool. 1-4 X 20 X 4.5 in, Hex17upholsteryC11189 Screw,518ConnectC02312 theLockwasher,Starhose to the wand and the female end to the machine by sliding 13.19male end.25ofin.,theInternalsolutionC11516 Screw, 1-4 X 20 X 4.5 in, Flat Head, Phillips1onHose,the ution.375, 100PSI,31 in lg fitting back. Push the male fitting in and release the knurled121collarJ11508ScrewClamp#6, .43 to .875 in8untilit snapsback.22 G11904 Power Prime14.23Makesuredrainvalveis closedA00060.25theMaleX .375Barb,Brass by pushing the T-handle all the way in.124PreviouslyA00053 45shampooedElbow, .25MPcarpetsX .25 FP usually have a heavy build-up of old shampoo residue which can cause15.25G03523-1 Valve, Regulator, 200 PSI1vacuumsystem.25MPto ingestfoam and result in damage to the vacuum motor. Remember to add recom-26theA0005290 Elbow,X .25FP327 00580-13in-MF-AHoseAsm, 13 toin X.25HP1amountofdefoamertherecovery tank every time you fill the solution tank.28mendedG00516-3Gauge,0-600PSI16.29If aC11244Powermateto beusedWasher,is.56X 1.5X .05with the machine, connect the male plug on the wand to the optional430 A00104 QD, 1-4 M X 1-4 FP, Brass1on.25theFP,machine.31receptacleA00161 Tee,Brass132 A00111 Nipple, .25 in233 C00232Washer, .5 in,Flat1AdditionalInstructionsforNPTGALAXY’s34 A0015490 Elbow, .25X .25 NPT with HEAT’N’RUN installed:135 C11440 Spacer, Heater Mounting Plate4Plug,1.25solutionin, Black tank with water before plugging in the machine.11.36BeK10510sure tofill the37 C02322 Hex Bolt,1-4 X 20 X 1.75 in42.38Waterhookupsbe in Plateplace and water flowing through the heater prior to turning it on. Failure to1doD010379HeatermustMounting39soC11165,Screw,#8 X 1 in,Pan, Blackdamage and will void the warranty.5may causeinternalcomponent40 F11790 Heater, Tunnel Cover, Blue Granite13.41SpraywatertheYellowtool / wand before turning on the heater to assure that there is water flow. 2B11779Stub,through12-3 illedwater or water based solutions at all times when in use.43 C00293 #8 X .5in Pan, Black SMS, Phillips25.44PlugheaterpowerwithcordGlueand machine power cord into separate outlets on separate circuits.B00192Tie Holder1B11606StrainRelief,Pigtail26.45Turnoff theswitchandunplug the heater from outlet when not in use.46 H03545 Cover, Serial # Label17.47DoH00565-5not useLabel,heaterSerialat morethan 500 PSI.Number148TurnC02305Cap Nut,.5in Push-on28.49on heaterswitchwhen you are ready to clean.C00240 Washer, Shoulder, Nylon450 G11767 Wheel, 10 in251 D11170Axle the green light on the heater is on, the heater is heating. When the green light is off, the1CAUTION:When52 F11789 Base153 C00314-1Hex Bolt,20toX 1in8waterin the heatertank1-4is Xuptemperature and the thermostat switch in the heater has turned the heater54 G03518 Caster, 4 in2off.will automaticallyturn120onVagain when the water temperature in the heater has cooled.55It G13102Pump, 500 PSI,156 B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated257 C03251 Washer, .187 ID, Backup1DELIVERMAXIMUMHEATby Fperformingthe following SYSTEM WARM-UP PROCEDURES at the start58 A00168Bushing .375M X .25Brass4 ofeachday: .50 Barb X .25 MP, Brass59 A90004160 A00155 Male Plug, .25 in, Nylon161 J11933.5 inhosePolywirePVC,33 indisconnectlg11.AttachtheHose,solutionto thequickon the machine.62 J00632 Pulse Hose, Pump - QD, 42 in22.Attachthe Nylonwarm-upquick disconnect with spray tip attached to the other end of the solution hose.63 B00190Tie, 4in13Plate,quickPump,disconnectGalaxy, Flatin the solution tank.164 D131033.Placewarm-up65 solutionH02564-2 olution.66 J11933 Hose, .5 in Polywire, 30 in15.Turnon pump.67 K11935Strainer, Inline, .5 in168 J11154SolutionHose,out.375,Wire, 27 quickin lg disconnect, turn on the heater.16.Whenwateris flowingof100PSI,the warm-up69 J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg17.Letthe pumpand VacheaterrunGalaxyfor 4 to 5 minutes.70 .Remove warm-up quick disconnect. Attach the wand or upholstery tool and begin cleaning.
Additional instructions for 200 PSI and 500 PSI models:Prime the pump system by connecting the drain hose, which is the 4 foot long solution hose with a connectoron one end, to the quick disconnect at the back of the machine and place the open end of the hose in thesolution tank. Turn on the pump thereby recirculating the clean water through the drain hose back into thesolution tank. When there is a steady stream of water running through the drain hose, the pump is primed.Disconnect the priming hose and attach the solution hose.The pump rarely needs to be primed after the first time of each day. If the solution tank is allowed to run low,it will result in the pump sucking air, then the pump will need to be primed again. Erratic pressure fluctuationindicates air in the lines and means that the pump needs priming.GALAXY 2000FX-HR (UPPER) PARTS LISTITEM #123456789Using the pressure adjustment and gauge on the back of the GALAXY, adjust the pump system to thedesired “operating pressure” while the cleaning tool is on (spraying).OPERATING INSTRUCTIONS- CARPET TOOL1. Turn on the vacuum and solution switches. Slowly pull the tool towards you withthe solution valve trigger engaged. Then make a pass forward and backwardwith the vacuum only (no spray) over the cleaned area to remove as much dirtand solution as possible. Do not overwet carpet! Make overlapping passes toprevent streaking.2. If the carpet is heavily soiled, squeeze solution valve on the forward pass aswell as backwards, allowing cleaning solution a few seconds longer to work priorto vacuuming. Another method is to raise the wand 8” above the carpet andpre-spray lightly prior to cleaning passes. On extremely soiled carpets, werecommend using a pre-spray solution.3. When you run out of solution, turn off the pump. Attach the drain elbow on thedrain valve. Place a pail under the downspout and pull up the drain valve T-handle.Dirty solution will pour out until the tank is empty. Close the drain valve. Use a cleanbucket when you refill the solution tank.4. When the job is completed, turn the switch off and disconnect the vacuum and solutionhoses from the carpet and the machine. Drain the recovery tank through the drain valve ART 0004D00373A00124C11143S11179DESCRIPTIONSOLUTION TANKRECOVERY TANKLID, SOLUTION TANK3-8 BARB X 1-4MP, BRASS90 ELBOW, .25MP X .25FPWASHER, .56 X 1.5 X .05HOSE ASSEMBLY, 16.5 IN X .25 INGASKET, RECOVERY TANKSTAND PIP ASSEMBLYELBOW, 180º FLOAT BALLPVC PIPE, 1.5 X 12 IN, SCH 40 WHITEADAPTERFLOAT BALL SCREENLID RECOVERY TANKWASHER, 1-4 X 1, SS1-4 X 20 BOLTEXTENSION CORD, 12-3 SJTWVELCRO STRAPLABEL, IMPORTANT, CORDWIRES, 73 INWIRES, 73 INWIRE HARNESSHANDLETERMINAL LUG, FEMALE, QD, .25 X .032, 16-14 AWG, FULLY INSULATEDWIRE, 14 GA, BLACK, UL1015, 10 IN#10 X .75 PAN, BLACK SMS, PHILIPS#8 X .5 IN PAN, BLACK, SMS, PHILIPSCOVER, SWITCHPLATESWITCH, ROCKER, GREEN LIGHTSWITCHPLATEGASKET, SWITCHPLATETERMINAL LUG, FEMALE, QD, .25 X .032WIRE, 14 GA, WHITE, UL1015, 10INLOCKWASHERNUT, 10-32SCREW, ALLEN HEAD, 10-24 X 1.25 INHOSE ADAPTER, 1.5 ON, BLACKGASKET, DRAIN VALVEHEX BOLT, 1-4 X .5SSWASHER, FLAT, .25 INLOCKWASHER, .25 IN., INTERNAL STARPLATE, HEATER MOUNTINGHEATER MOUNTNUT, .25-20, HEXELBOW, DRAIN VALVE, BLACKDRAIN VALVE, BLACKLOCK WASHER, 1-4 IN SPLITSCREW, 1-4 20 X 1.25ELBOW, 90, 1.5 IN, MT-MS, PVCPVC PIP, 1.5 X 2.25 IN, SCH 40 WHITEGASKET, 5 FT, LONG.50 BARB X .25 MP, BRASSINLET FILTER, .25 NPTHEX NUT NPT, BRASSSCREW, 1-4 20 X 1.25 IN, SS PAN HEAD, PHILIPNON-SKID TAPE, 1 IN. 2112211112221
POWERMATE 1204AC/1204ACH (OPTIONAL)14 15 16 17 18 19 20 21 22 23 4393540364134423643444546475251474648550 492000FX-HRUpper1-26-08372000FX-HRUpper1. Connect the cord on the power wand to the 1-26-08optional receptacle in back of the machine.IMPORTANT: 1204AC is for use with 50, 100 and 150 PSI pump systems1204ACH is for use with 200, 250 and 500 PSI pump systems.Turn on the vacuum and pump switches.ITEMPARTNUMBER2. NO.The motor for the power brush isturnedon and off by a lighted rocker switch DESCRIPTIONlocatedon Solutionthe top Tankof the base. Solution application is controlled by squeezing1 F117872F11792RecoveryTankthe solution valve lever.3 F11791 Lid, Solution Tank3. Tomove the power wand forwards, push the wand handle downward, raise4 A00060 3-8 Barb X 1-4MP, BrasstheendpushtheXwand5 frontA0005290 andElbow,.25MP.25FP into position using the rear wheels. To pre-6 C11244Washer,.56 X valve1.5 X .05spray,squeezesolutionlever while moving wand forward and backwards7 00580-16.5 in-PH-A Hose Asm, 16.5 in X .25 inoverthe areato beRecoverypre-sprayed.8 E11124Gasket,Tank4. ToliftStandthe wandhandle to insure the nose of the wand is against the12904APipe Assembly9 clean,carpet,thenElbow,while 180squeezingtheBallsolution valve lever, pull the wand towardsDeg. Float9A K119659B K00672 Pvc Pipe, 1.5 X 12 in, Sch 40 Whtyou.Adapter9C K00741Here’show it works- the solution is jet sprayed deep into the carpet9D 10989-2A Float Ball Screento loosen the dirt. The brush scrubs the fiber and breaks up surface10 F11785 Lid, Recovery Tankdeep1-4dirt. It11 C12039andWasher,X 1, SSfluffs the nap without distortion to the pile. With the12 C02322weight1-4 X 20ofBoltthe base on the suction head, the vacuum picks up the dirt13 B11769 andExtensionCord,12-3 SJTWsolution.Makeoverlapping passes to prevent streaking.14 C11177 Velcro Strap5. Gooverthepathyoujustcleaner15 H02548-2 Label, Important, Cord without squeezing the solution valve lever toremoveas much Wires,dirt andsolution as possible.16 B00185-3073 inQTY.1112331111111122222217 B00185-40 Wires, 73 in218B010314WireHarness1POWERMATE 1800AC-100 and 1800AC-200 (OPTIONAL)19 F11786 Handle120 B00177 Terminal Lug, Female, QD, .25 X .032, 16-14 AWG, Fully Insulated4IMPORTANT:1800AC-100is for usewith1010021 B00185-40Wire,14 GA Black,UL1015,in & 150 PSI pump systems11800AC-200is foruseSMS,withPhillips200 & 500 PSI pump systems22 C00295-1#10 X .75in Pan,Black223 C00293 #8 X .5in Pan, Black SMS, Phillips224 D1116811. ConnecttheCover,cord Switchplateon the power wand to the optional receptacle in the back of the machine. Turn on the25B02211-1Switch,Rocker,GreenLight3vacuum and pump switches.26 D010284 Switchplate12. The motor of the rotating power brush is operated with your right hand controlling a long toggle switch.27 E010453 Gasket, nis28 B00177-1 Terminal Lug, Female, QD, .25 X .0322controlledby depressingthe flowswitchwith your right hand fingertips.29 B00185-30Wire,14 GA White,UL1015,10 leverin130 adjustC02315Lockwasher,#10Int. Str, SSposition, pull up the grip on the locking lever located near the base2 of3. Tothehandle intooperating31C00264Nut,10-321the handle. Move the handle to waist level height and push down grip handle on lever to lock into place.32 C11141 Screw, Allen Head, 10-24 X 1.25 in84. Tothe Hosepowerwand forward,push handle downward to raise the front end and move the wand into33 moveK00665-1Adapter,1.5in, Black1position.ToGasket,pre-spray,34 E11128DraindepressValve the flow switch lever (solution control) while235C00313HexBolt,1-4X20X.5SS6moving wand forwards or backward over the area to be cleaned with the front36 C00233 Washer, Flat, .25 in8endraised. Lockwasher, .25 in., Internal Star37 C02312238 clean,D010283Plate, HeaterMounting15. Todepressthe solutionflow lever while pulling the power wand towards you.39F11804HeaterMount1Here’s how it works- the solution is jet sprayed deep into the carpet40 C00261 Nut, .25-20, Hex2loosendirt.The rotatingbrush scrubs the fiber and breaks up surface41 K00710toElbow,DrainValve,Black1rooted42 K00711andDraindeepValve,Black dirt. It fluffs the nap without any distortion to the pile143 C00254WithLocktheWasher,1-4in2weightof Splitthe base on the suction head, the vacuum picks up44C02294Screw,1-420X1.252the dirt and solution. Make overlapping passes to prevent streaking.45 K11185 Elbow, 90, 1.5 in, MT-MS, PVC16. Makea passPvcoverthe1.5pathyouin,just46 K00672-1Pipe,X 2.25Schcleaned40 Wht without depressing the solution flow1lever(vacuumonly)andwith the brush47 E11129Gasket,5 ft.Long148A90004.50BarbX.25MP,Brass1still on to remove as much dirt and solution49 D00373 Inlet Filter, .25 NPT2aspossible.50 A00124 Hex Nut, .25 NPT Brass251 C11143 Screw, 1-4 20 X 1.5 in, SS Pan Head, Phillips252 S11179 Non-Skid Tape, 1 in. Roll1
CLEANING UPHOLSTERYCleaning upholstery with success requires a good knowledge of the type of fabric you will work on. Look forthe cleaning instructions label sewn on the underside of the furniture for the recommended method of cleaning. If it calls for dry cleaning, do not attempt to clean by wet extraction otherwise damage to the fabric couldoccur. Extraction works perfectly on most synthetic fabrics including synthetic velvets.Before proceeding, test the fabric for colourfastness. Apply a small amount of cleaning solution on the fabric in an inconspicuous spot. Wait 2 to 3 minutes and rub the area with a white terry cloth towel. If no colorcomes off the towel, the fabric should be safe to clean. If a little color comes off, there is some risk of colorsrunning when you clean. It may be possible to stabilize colors by cleaning with an acidic rinse.1. Prepare the machine in the same manner as for carpet cleaning (see Preparing the Machine) exceptattach the upholstery tool to the vacuum hose. Connect the solution hose. Pour hot water into thesolution tank. Add recommended amount of cleaning concentrate into the solution tank. Turn on thevacuum and pump switches.2. Adjust the pump “operating pressure” to 50 PSI or below for upholstery cleaning (See Preparing theMachine).3. Clean with the upholstery tool using as little solution as possible. Make overlapping passes to preventstreaking. Go over the area you just cleaned without depressing the lever (vacuum only) and gauge theamount of moisture extracted through the view window for dryness. On heavily soiled areas likearm rests, pre-treat with a recommended pre-spray solution or hold the upholstery tool a few inchesabove the fabric and press lever to spray on the solution before making a pass.DAILY MAINTENANCE1. Always keep the machine clean inside and out.2. Pour 2 gallons of clean hot water in the solution tank. Turn on and flush the entire system through thewand nozzles for about a minute to prevent build-up.3. Remove dirt and lint build-up inside the filter screen in the recover tank. Lint should be cleaned off so thatair flow is not impeded.4. Check the solution tank strainer in the solution tank. If lint has accumulated in the screen, remove andrinse it in clear running water.PERIODIC MAINTENANCEAll EDIC machines are engineered and built to require a minimum of maintenance. But like any machine,it does require some care to keep it in optimum working condition. Careful attention to these maintenanceinstructions will give you maximum operating performance and will increase the life expectancy of your machine. Solution Lines and Fittings: Flush the machine at least once a month with a solution of 3 parts water with1 part white vinegar in order to neutralize the alkaline residue left by the cleaning solution.Quick Connect Coupler: Spray with WD-40 or equivalent lubricant to prevent coupler from sticking.Drain Valve: Apply light oil on gate seals. If machine has to be stored, leave the gate valve open.Solution Pump: The same above procedure used on the solution line and fittings applies to the pump.GALAXY 2000WX-HR and KX-HR (BASE) PARTS LISTITEM 55565758596061626364WX PART #KX PART 54J00618E11169B00179-2DESCRIPTION#8 X .25 PAN HEADHOSE, 3 INSCREW CLAMP, 1.63-2.43 INVACUUM HOSE, 2 IN GREY, WIRE, 22 IN LGINTERCOOLER, GALAXY, BLACKLOCKNUT, 1-4 X 20, NYLON, SSWASHER, FLAT, .25 INGROMMETSCREW, 10-32 X .375 GROUNDGROUND WIRE, GALAXYWX: VACUUM, 135IN, 115V, 5.7; KX:VACUUM, 147IN., 115V, 5.7INHOSE CLAMP, 2 IN SLDPRTVACUUM HOSE, 2 IN GREY, WIRE, 4 IN LGNUT, .25-20, HEXLOCK WASHER, 1-4 IN SPLITVAC PLATESCREW, 1-4 X 20 X 4.5 IN, HEXLOCKWASHER, .25IN. INTERNAL STARSCREW, 1-4 X 20 X 4.5IN FLAT HEAD, PHILIPSNIPPLE, .25 IN90 ELBOW, .285MP X .25FPTEE, .25 FP, BRASSFITTING, .25MP X .25FP, BRASSWASHER, .56 X 1.5 X .05QD, 1-4M X 1-4FP, BRASS90 ELBOW, .25 NPT X .25 NPTWASHER, .93ID X 1.5 ODHOSE ASSY, 13 IN X .25HPVALVE, REGULATOR, 200 PSIGAUGE, 0-600PSISPACER, HEATER MOUNTING PLATEPLUG, 1.25IN, BLACKHEX BOLT, 1-4 X 20 X 1.75INHEATER MOUNTING PLATESCREW, #8 X 1IN, PAN, BLACKHEATER, TUNNEL, COVER, BLUE GRANITESTUB, 12-3 SJTW YELLOWNYLON TIE, 11IN BLACK#8 X .5IN PAN, BLACK SMS, PHILLIPSTIE HOLDER WITH GLUESTRAIN RELIEF, PIGTAILCOVER, SERIAL # LABELLABEL, SERIAL NUMBERCAP NUT, .5 IN, PUSH-ONWASHER, SHOULDER, NYLONWHEEL, 10 INAXLEBASEHEX BOLT, 1-4 X 20 X 1 INCASTER, 4 INPULSE HOSE, PUMP-QD, 42 INCAP, FPT, .375 BRASSPUMP, 200PSI, 120VNYLON TIE, 4 INSCREW CLAMP #6, .43 TO .875 INPLATE, PUMP, GALAXY, FLATLABEL, CAUTION, MOTOR HOUSINGHOSE, .5 IN POLYWIRE, 20 INSTRAINER, INLINE, .5 INHOSE, .5IN POLYWIRE, 33 INSOLUTION HOSE, .375, 100 PSI, WIRE IN LGVACUUM HOSE, 2 IN GREY, WIRE, 7 IN LGGASKET, VAC MOTOR, GALAXYCLOSED END CNTR, 1112411182211136111111124
2000WX-HR & KX-HR Base200 PSI 4-1-08TROUBLESHOOTING12354678910111264631314361 6215282616172721 22 23 24 257292117186030193855 565758593133 34 35323653 545140263938374142432152264510515049487474645 442000WX-HR &KX-HR Base200 PSI 49505152535455565758596061626364Electrical SystemWX PART NUMBERKX PART NUMBERPROBLEM CAUSEPROBLEMC00297#8 X .25 Pan HeadJ11863 Hose, 3 inNo electricalpower.J00639Screw Clamp,1.63 - 2.43in. 1. Defective power cord.2. 22HouseJ00618 Vacuum Hose, 2in Grey, Wire,in lg or building circuit breaker tripped.QTY.1131F11178-BLK Intercooler, Galaxy, Black1Switchis turnedC00273Locknut,1-4 Xon.20, Nylon, SS 1. Faulty electrical cable.16PowerWasher,is intermittentto2. Defective switches.C00233Flat, .25 oloredterminalconnections.C00284 Screw, 10-32 X .375 Ground2B11150GroundSystemWire, Galaxy2VacuumG00520-1L Vacuum , 135 in, 115 V, 5.7 inG02517-1 Vacuum, 117 in., 115 V, 5.7 in21. Drain valve open.J00657 Hose Clamp, 2 inSLDPRT1J00618Vacuum Hose, 2 in Grey, Wire,4 in lg1No Vacuum2. Vacuumlid is not sealed against tank.C00261 Nut, .25-20, Hex103. Loose vacuum hose, vacuum connection.C00254 Lock Washer, 1-4in Split1Low Vacuum1. Accumulated dirt on lid screen.D11134Vac Plate1C11189 Screw, 1-4 X 20 X 4.5 in, Hex2. Worn out vacuum lid gasket.5C02312 Lockwasher, .25 in., Internal Star1C11516 Screw, 1-4 X 20 X 4.5 in, Flat13.Head,Lint &Phillipsdirt build-up on wand head.A00111 Nipple, .25 in14. Defective vacuum hose.A00052 90 Elbow, .25MP X .25FP45. Loose connection in the vacuum motor (s).A00161 Tee, .25 FP, Brass1A00121Fitting, System.25 MP X .25 FP, Brass1SolutionC11244 Washer, .56 X 1.5 X .055PumpmotornoFP, Brass 1. Clogged spray tips.A00104QD,1-4 Mon,X 1-41A00154Elbow,.25 tipsNPT X .25 NPT 2. Clogged solution intake filter screen.3spray90thrusprayC11560 Washer, .93 ID X 1.5 OD13. Plugged female quick disconnect coupler.00580-13in-MF-A Hose Asm, 13 in X .25HP1G13133 Valve, Regulator, 200 PSI 4. Punctured pump diaphragm. (100PSI only)1G00516-3 Gauge, 0-600PSI15. Defective pump check valve. (100 PSI only)C11440 Spacer, Heater Mounting Plate46. Crack in pump housing.K10510 Plug, 1.25 in, Black1C02322 Hex Bolt,1-4 X 20 X 1.75 in 7. Debris in check valve. (100 PSI only)4D010379 Heater Mounting Plate18. Lost Prime.C11165, Screw, #8 X 1 in, Pan, Black4F11790Heater,TunnelsprayCover, Blue Granite1Unevenor weak1. Clogged or dirty spray tips.B11779 Stub, 12-3 SJTW Yellow1fromNylontips. Tie, 11in Black2. Accumulated dirt on solution intake filter screen.B001914C00293 #8 X .5in Pan, Black SMS, Phillips23. Accumulation of debris inside pump and plumbing.B00192 Tie Holder with Glue14. Worn pump bearing (excessive noise).B11606 Strain Relief, Pigtail15. Punctured pump diaphragm.H03545 Cover, Serial # Label1H00565-5 Label, Serial Number16. Defective rectifier or motor.C02305 Cap Nut, .5in Push-on27. Worn nozzles.C00240 Washer, Shoulder, Nylon48. Pressure regulator set incorrectly.G11767 Wheel, 10 in2D11170 Axle1Vacuum1. Loose wiring connection.F11789Base motor (s)1C00314-1HexpumpBolt, 1-4X 20 X 1in8working,motor2. Defective pressure switch in pump (100PSI model).G03518 Caster, 4 in2fails toPulseturnHose,on Pump - QD, 423.J00632-1in Defective pump motor or rectifier.2A13140Cap,FPT, .375 Brass1ErraticPressure1. Pump check valves defective or dirty.G13132Pump,200PSI,120V1200 & 500 PSI Models2. Lost prime.B00190 Nylon Tie, 4in13J11508 Screw Clamp #6, .43 to .875 in6D13103Plate, Pump,Galaxy, Flat1OPTIONALACCESSORIESH02564-2 Label, Caution, Motor Housing1J11933Hose, .5 in Polywire, 20 in1HEAT-N-RUNK11935.5 in up to 200oF heat enchancing productivity and cleaning. Models 600HR1InlineStrainer,heaterInline,deliveringJ11933 Hose, .5 in Polywire, 33 in1and Solution602HR.Hose, .375, 100PSI, Wire, 27 in lgJ111541J00618 Vacuum Hose, 2 in Grey, Wire, 7 in lg1E11169 Gasket, Vac Motor, Galaxy2B00179-2 Closed End Cntr, 16-34
11 12 13 14 15 16 17 18 19GALAXY 2000WX-HRand KX-HR(UPPER) PARTS LIST2000SX-HRUpper20ITEM 2
GALAXY GALAXY 2000EL 2000CX-HR 2000EL-EH 2000FX-HR 2000SX-HR 2000JX-HR 2000MX-HR 2000ZX-HR 2000WX-HR 2000HX-HR . OWNER'S MANUAL & PARTS LIST ZF1202 REV 7/08. BEFORE OPERATING THE MACHINE Read the manual carefully and completely before attempting to operate the unit. This manual has important information for the use and safe operation of the .
