Transcription
door accessoriesQuick CloserExclude-A-Seal Emb-A-Seal Rolling Garage Door SealSectional Garage Door SealLintel-SealCarport Conversion KitLocks & HandlesAuto-LockIndependent Taper
Quick CloserProduct CodeSD0003/SD0004single and double end stiledescriptionThe preferred method for B&D Panelift andPanelift Icon installations is the normally suppliedoption of standard or low headroom.In situations where there is inadequate headroomto fit the standard equipment the B&D Quick Closersystem may be an option as it allows the door andopener to fit into 180mm of headroom above the topof the door panels.Notes / InformationA) Quick Closer, in normal residential use, is covered by a 1 year warranty,excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to Qucik Closers purchased and installed inAustralia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.It should be noted that this mechanism will extend350mm past the fully open door and will not workon manually operated doors as it requires theopener to fully open and close the door, for someinstallations this may cause the top panel to slamshut when the door fully closes.SIDE VIEWDOUBLE END STILEQUICK CLOSERQUICKCLOSER(0T4433)DOUBLE ENQUICK CLOOPENER-'C' RAILWHEELS AND AXLESINSTALLED IN BACK HOLESREO64180OPENER-'C' RAILREOINSTALLATION CLEARANCESDoor Height (mm)Door Width (mm)Additional intrusionto the fully opendoorHeadroom (mm)with or without anopenerSideroom (mm)Panelift Icon /Panelift1760 to 39901800 to 6600350mm180140/120November 2017RETURN TO INDEXSECTION 04/1
Product CodeMS0010sectional and rolling overhead garage door sealdescriptionThe B&D Exclude-A-Seal is an accessory designedto assist the door’s standard bottom rail seal inexcluding dust, debris, pests and weather ingressunder the door. B&D testing showed that waterpenetration was less evident with the seal fitted thanwithout it.Notes / InformationA) Exclude-A-Seal , in normal residential use, is covered by a 1 yearwarranty, excluding labour to repair, when installed by an approved B&Ddealer. 1 year warranty only applies to Exclude-A-Seals purchased andinstalled in Australia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.The seal is able to be used on B&D sectional androlling overhead doors and should if possible be runpast the width of the door with the ends mitredand returned into the structure.There are two kits available:3.3m P/N: OT85146.6m P/N: sPestDirtJAMBINSIDEOF DOOROUTSIDEOF DOORDOORThe seal is made from extruded black PVC whichis UV stabilised quality and is designed to beglued to a level garage floor as shown, it is notrecommended for use if the floor is not level oreven.EXCLUDE-A-SEALExclude-A-SealWaterNOTE: Alternative glue to that specified maycompromise the adhesion properties.CONCRETENovember 2017RETURN TO INDEXSECTION 04/2
rolling garage door sealfeatures Seals are designed to work in conjunction with adoor to lintel gap of up to 45mm for rolling doors. Superior gap filling ability ensures that a solidbarrier is created around the door, reducing therisk of embers flying in. Manufactured from flame retardant material,seals help delay the onset of fire. Seals also act as a barrier to prevent dust, sandand vermin from entering the home, creating acleaner internal environment, which is becomingmore important given the use of the garage asan extra living area.specificationsdescriptionThe B&D range of Emb-A-Seals offer solutions forboth sectional and rolling doors. Whether for thegarage, the shed or any other application, B&D hasa seal that will ensure peace of mind for many yearsto come.Aluminium holder is fastened to the roll of thecurtain, just above the height of the lintel. Flameretardant brush seal slides into the holder and restsabove the lintel to provide a barrier.Seal is compressed when the door curtain rollsaround the drum. This ensures that door operation isunaffected and that the seal is not visible whilst thedoor is open.profileSeals: 50mm fire retardant bristle brush seal forthe door. For mandatory BAL information refer toAS3959-2009 and the compliance section of thismanualSeal Holders: Features 50mm aluminium F carriersfor the lintel.installation clearancesThis GapLintel45mmMax6.8mm50mmMODELEmb-A-SealPART NUMBERAluminium Extrusion - 0T549550mm Brush Seal - 0T5497length3000mmsize rangeNotes / InformationA) Emb-A-Seal , in normal residential use, is covered by a 1 year warranty,excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to Emb-A-Seals purchased and installed inAustralia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.Available in lengths up to 3000mm.November 2017RETURN TO INDEXSECTION 04/3
sectional garage door sealfeatures Seals are designed to work in conjunction with adoor to frame gap of up to 16mm for sectionaloverhead doors. Suitable for all flat or grooved type panels. Superior gap filling ability ensures that a solidbarrier is created around the door, reducing therisk of embers flying in. Manufactured from flame retardant material,seals help delay the onset of fire. Seals also act as a barrier to prevent dust, sandand vermin from entering the home, creating acleaner internal environment, which is becomingmore important given the use of the garage asan extra living area.The B&D range of Emb-A-Seals offer solutions forboth sectional and rolling doors. Whether for thegarage, the shed or any other application, B&D hasa seal that will ensure peace of mind for many yearsto come.Seals are suitable for use in high fire risk zones, dry,arid climates, coastal areas and dusty regionswhere high winds are present.Comprising of aluminium seal holders that are fixedbehind the jambs and lintel. Bristle brush seals fit intothese holders to prevent the entry of embers.profile8mmspecificationsSeals: 25mm fire retardant bristle brush seal for thelintel and jamb. For mandatory BAL information referto AS3959-2009 and the compliance section of thismanualSeal Holders: Features aluminium carriers for thejamb and lintel. The width of the carriers is 50mm.installationclearancesDoor PART NUMBERCarrier - 0T549425mm Brush - 0T5496Single door kit0T5503Double door kit0T5501length3000mmsize rangeAvailable in lengths up to 3000mm.RETURN TO INDEXNotes / InformationA) Emb-A-Seal , in normal residential use, is covered by a 1 year warranty,excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to Emb-A-Seals purchased and installed inAustralia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goodspreviously ordered. Specifications subject to change withoutnotice.C) Prefixed Trademarks are trademarks of B&D AustraliaPty Ltd.D) B&D products have many patents and registereddesigns applicable.November 2017E) Details correct at date of publication.SECTION 04/4
Lintel-Sealrolling garage door sealfeatures Seals are designed to work in conjunction with adoor to frame gap of up to 38mm for rolling doors. Size of the rolling door seal can be adjusted toperfectly suit the application thanks to patentedtear off system. Seals also compress to disappearout of sight whilst the door is open. Superior gap filling ability ensures that a solidbarrier is created around the door. Manufactured from flame retardant material. Seals also act as a barrier to prevent dust, sandand vermin from entering the home, creating acleaner internal environment, which is becomingmore important given the use of the garage asan extra living area.descriptionThe B&D range of seals offer solutions for bothsectional and rolling doors. Whether for the garage,the shed or any other application, B&D has a seal thatwill ensure peace of mind for many years to come.Seals are suitable for use in dry, arid climates,coastal areas and dusty regions where high windsare present.Aluminium holder is fastened to the roll of thecurtain, just above the height of the lintel. Flameretardant rubber compound slides into the holderand rests above the lintel to provide a barrier.Seal is compressed when the door curtain rollsaround the drum. This ensures that door operation isunaffected and that the seal is not visible whilst thedoor is open.specificationsSeals: Flame retardant rubber compound with45mm drop. Coverage can be reduced viapatented tear off system to adapt perfectly to theapplication. When the door is opened, the sealrolls up and disappears out of sight. For mandatoryBAL information refer to AS3959-2009 and thecompliance section of this manual.Seal Holders: Aluminium extrusion featuring two feetto hold the seal in position. The overall width of theseal holder is 42mm.Fixings: Fasteners provided fix the aluminium sealholder to the door curtain.installation clearancesThis GapprofileLintelMOUNTING RAIL38mmMaxMODELLintel-SealPART NUMBERSingle Kit - 051855Double Kit - 051856MAX DOOR HEIGHTNoneMAX DOOR WIDTH5500mmsize rangeAvailable up to a maximum width of 5500mm.RETURN TO INDEXNotes / InformationA) Lintel-Seal, in normal residential use, is covered by a 1 year warranty,excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to Lintel-Seals purchased and installed inAustralia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D AustraliaPty Ltd.D) B&D products have many patents and registereddesigns applicable. International patent number:PCT/AU2005/001354.November 2017E) Details correct at date of publication.SECTION 04/5
Carport Conversion KitCarport Conversion Kitdescriptionthe kit includesB&D carport conversion kits facilitate the installationof a B&D Roll-A-Door to a carport. 1 x pair of jambsmax jamb height3000mmmax jamb depth75mmmax jamb width135mmmax head infill height600mmmax head infill width3100mmKRR1D/APR1D 1 x pair of jamb coversThe two main advantages are that the appearanceof the infill panel and jambs match the door andthere is no need to use a carpenter to build in frontof the carport. Doors can be installed by doorinstallers.size rangeProduct Code 1 x pair of end supportsNOTE: The carport conversion kit does not includethe Head infill panel. This must be orderedseparately. A top levelling channel may also berequired.Notes / InformationA) Carport Conversion Kit, in normal residential use, is covered by a 1 yearwarranty, excluding labour to repair, when installed by an approvedB&D dealer. 1 year warranty only applies to Carport Conversion Kitspurchased and installed in Australia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.head infill panel for carport conversion kitTop Levelling ChannelHead Infill PanelEnd SupportJamb CoverJambNovember 2017RETURN TO INDEXSECTION 04/6
Locks & Handlesdoor accessoriesThere are various types of locks available for your B&D door, somecome as standard and others are available as options or extras.“D” Pull Handle PlasticSeries 1, 2, 3P/N: 49848“D” Pull Handle Cast MetalChrome PlatedSeries 1, 2, 3.P/N: 49849“D” Pull Handle Pressed MetalGalvanised Series 1, 2, 3P/N: 51755External Stainless Steel Slide Lockwith position for 2 x padlocksSeries 1, R1M & R1MEP/N: 51765External Stainless Steel Slide Lockwith position for 1 x padlock and1 x keyed overlocker. Series 1, 2, 3P/N: 51184Keyed OverlockerP/N: 51189External Cast Aluminium SlideBolt with position for 2 x padlocksSeries 1, R1M & R1MEP/N: 47686External traditional recessed slidelock with position for 2 x padlocksR1MP/N: 07167External/Internal Bottom Rail SlideLock with position for 1 x padlockSeries 1P/N: 5695External/Internal Bottom Rail SlideLock position for 1 x padlockSeries 2P/N: 6577Internal Waist High LockSeries 2P/N: 6136Internal waist high lockSeries 3P/N: 48605November 2017RETURN TO INDEXSECTION 04/7
Locks & Handlesdoor accessoriesCentre Lift LockS1, RollmastaP/N: 52001Centre Lift LockSeries 1, 2, 3 Roll-A-DoorP/N: 9052Centre lift lockS1 FirmadoorP/N: 61100Classic centre lockSeries 1, 2, 3.P/N: 3492V9 C4 Roller Door LockP/N: 51786Auto Lockwill only work with B&DControll-A-Door (see separate page)Notes / InformationA) Locks, in normal residential use, is covered by a 1 year warranty, excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to locks purchased and installed in Australia or New Zealand.B) The company reserves the right to make changes or improvements to the products or accessories without notice and without incurringany obligation to make similar changes or improvements to goods previously ordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.November 2017RETURN TO INDEXSECTION 04/8
Auto-Lockdoor accessorieskitsBase Kit - part no: MC0002This kit contains lock including batteries, transceiver,fixings, instructions and warranty.It is suitable for fitting to theleft or right hand side ofall sectional overheaddoor tracks which haveat least 100mm ofadditional sideroom.Installation instructionscan be found on the B&Dwebsite www.bnd.com.au.descriptionAs the largest door in the home, the garagedoor plays an important role in protecting what’svaluable to you and although the garage storessome of the most valuable things we own, many ofus compromise on garage security.In response to a growing demand for extra securityand convenience, we have introduced the B&DAuto-Lock.The B&D Auto-Lock is compatible with all currentB&D Controll-A-Door sectional overhead dooropeners and openers produced from 2nd May 2016.how it worksEvery time you close your garage door the AutoLock sends a heavy duty bolt through the guard railhelping to prevent thieves from being able to forceit up and open - all without the need for a key. Inemergencies manual override button is included.Notes / InformationA) Auto-Lock, in normal residential use, is covered by a 1 year warranty,excluding labour to repair, when installed by an approved B&D dealer.1 year warranty only applies to Emb-A-Seals purchased and installed inAustralia or New Zealand.B) The company reserves the right to make changes or improvements tothe products or accessories without notice and without incurring anyobligation to make similar changes or improvements to goods previouslyordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.Additional B&D Panelift Limited SideroomBracket Kit - part no: MC0071Panelift limited sideroom bracket kit allowsfor fitting the lock tothe panel end stile, aseparate lock strikeattaches to the track.Kits include bracketsand fixings.Additional B&D Storm-Shield Bracket Kitpart no: MC0070Panelift Storm Shieldrequires this kit asit attaches to thedouble end stile,with the lock strikeattaching to theTracklock. Kits includebrackets and fixings.Additional Rear Hinged and T&G Bracket Kitpart no: MC007Rear hinged ortongue and groovestyle panels requirethis kit as the lockmust be set backfrom the panel toalign with the trackwhich has the lockstrike attached to it.Kits include bracketsand fixings.November 2017RETURN TO INDEXSECTION 04/9
Independent TaperProduct CodeR1Tdoor accessoriesdescriptionIndependent tapers are designed as an alternativesolution to fixed tapers for Series 1,2,3 Roll-A-Door and Flex-A-Door where the door is required tofollow continuous gradient out of level floor.The section is flat with no corrugations it has analuminium rail top and bottom which is notched ateach end to suit the guide section, is has a singleguide block roller on the short side and two on thelong side.see detaildetailBBAttachment to the door is by dome head bolts andwiz nuts which require the fixing holes to be drilledto suit on site.size rangeShort side 105mmLong side 105mm to 290mmdrill 8.5holes on sitesee detailAcolourSame as door series.important note: There will be a double aluminiumsection showing on the external face betweenthe door and taper joint. Also it is important tonote when fitted to Flex-A-Door it will affect thewalk under height and may affect Rolling Doorsdepending on the individual installation.detailANotes / InformationA) Independent Taper, in normal residential use, is covered by a 1 year warranty, excluding labour to repair, when installed by an approvedB&D dealer. 1 year warranty only applies to Carport Conversion Kits purchased and installed in Australia or New Zealand.B) The company reserves the right to make changes or improvements to the products or accessories without notice and without incurringany obligation to make similar changes or improvements to goods previously ordered. Specifications subject to change without notice.C) Prefixed Trademarks are trademarks of B&D Australia Pty Ltd.D) B&D products have many patents and registered designs applicable.E) Details correct at date of publication.November 2017RETURN TO INDEXSECTION 04/10
November 2017 RETURN TO INDEX SECTION 04/4 mDELO Emb-A-Seal PaRT NUmBER Carrier - 0T5494 25mm Brush - 0T5496 SINgLE DOOR kIT 0T5503 DOUBLE DOOR kIT 0T5501 LENgTH 3000mm description The B&D range of Emb-a-Seals offer solutions for both sectional and rolling doors.
