WIXLIB

Arduino M KR IoT CarrierProduct DatasheetSKU: ABX00047DescriptionThe MKR IoT Carrier provides infinite possibilitiesfor IoT projects.The integrated sensors, circuits and display leaveyou free to focus on programming and prototypingyour ideas.Target areas:IoT applications, MKR hobbyistsFeaturesNote: This board is passive and requires a MKRboard to function. Groove Connectors Capacitive sensingGroove modules and sensors 0-100% humidity sensing range 2x analog sensor input Humidity accuracy: 3.5% rH, 20 to 1x I2C interface 80% rHTemperature accuracy: 0.5 C,15 toST LSM6DSOX 6-axis IMU Sensor 40 C3-axis accelerometer I2C interface to Arduino MKR board2/ 4/ 8/ 16 g full scale Low power consumption (2μA @ 1 Hz3-axis gyroscope125/ 250/ 500/ 1000/ 2000 dps(degrees per second ) ST HTS221 Humidity SensorEasy interface with wide range of I2C interface to Arduino MKR boardLow power consumption (0.55mAmax)Rounded 1.3” TFT Displaysampling rate) Broadcom APDS-9660 RGB and GestureSensor Ambient light and RGB Colour SensingProximity Sensing Gesture Detection 240 x 240 resolution UV/IR Blocking Filter 36 x 40 mm I2C interface to Arduino MKR board

ST LPS22HBTR Pressure Sensor MemoryI2C interface to Arduino MKR boardRelays SD Card slotPower 2x KEMET EE2-5NU-L relays LI-ION 18650 3.7 v battery holder 5V Coil voltage USB Battery charging via MKR Board 2A Current(Runs up to 48h with a 3.7v220V DC, 250V ACNon-latching2500mAh) Common, normally open and 5x Capacitive qTouch buttons260 to 1260 hPa (0.25 to 1.24 atm)absolute pressure range LED Status Indicator Peripherals 5x Capacitive buttons Buzzer I/Onormally closed contacts5x Digital RGB LEDsRounded OLED 1,3” Display All sensors feature wake up function 2x Analog Grove connectors1x I2C Grove connector 2x relay connectorSafety information Class A

ContentsThe board1.1 Application examples1.2 Accessories1.3 Related products4444Functional Overview52.1 Board topology2.2 Power tree57Solution overview8Board Operation8Connector Pinouts105.1 Battery Clips5.2 A55.3 A65.4 I2C5.5 Relay 1/Relay 211111111126. Mechanical information126.1 Board outline/ mounting holes7. Ratings7.1 Absolute Maximum Ratings8. Certifications8.1 Declaration of Conformity CE DoC (EU)8.2 Declaration of Conformity to EU RoHS & REACH 211 01/19/20218.3 Conflict Minerals Declaration121313131313149. FCC Caution1510. Company information1611. Reference Documentation1612. Revision History17

1.The board1.1 Application examplesLight controller: Control your house lightning with the IoT Carrier, using the RGB lightsensor. This feature identifies the general amount of light in a room or environment andadapts. If the board is connected to Wifi, you can manage and control your deviceremotely on a smartphone via the IoT Cloud.Light and water controller for greenhouse: W ith moisture sensor, pressure sensor andtemperature the IoT Carrier can evaluate and recognize the moisture of the soil, dependingon air humidity and sun. Through the various sensors, it can reconstruate suitable climate(e.g. tropical) with the help of heaters and relays to increase the humidity. It can also beprogrammed with a watering system thanks to the relays.Weather station: With temperature sensor, pressure sensor, humidity sensor and lightsensors, you can easily use your IoT carrier as a local weather station. The various sensorscan via sensors collect statistics about the different variables required to display weather.1.2 Accessories-18650 Li-ion battery-Grove sensors1.3 Related products-Arduino MKR 1010 (SKU: ABX00023)-Protective case-TFT Display

2.Functional Overview2.1 Board topologyFront viewRef.DescriptionRef.DescriptionU1LSM6DSOXTR 6-axis IMU ICU3LV52204MTTBG LED Boost DriverICU2APDS-9660 RGB and GestureSensor ICHS-1HTS221 Humidity Sensor ICLPS-1LPS22HBTR Pressure Sensor ICL0-L4APA1022020-2018 RGB LED ICJ6FH26W-45S-0.3SHW(60) DisplayConnectorJ12SFV24R-1STBE1HLF DisplayConnector

Back viewRef.DescriptionRef.DescriptionJ2, J3Analog Groove ConnectorsJ4I2C Groove ConnectorJ11B2B-PH-SM4-TB(LF)(SN) PowerConnectorJ9, J101771033 3-pin Relay ConnectorJDIGITAL1MKR Power and Digital PinConnectorJANALOG1MKR AREF and Analog PinConnectorS1,S2EE2-5NU-L 2A 250V MechanicalRelayM1BuzzerJ1Micro SD ModuleJ7, J8Li-Ion 18650 Holder

2.2 Power treeThe Arduino MKR IoT makes use of the power management features of the Arduino MKRboards to power itself as well as to interface with the Li-Ion battery.

3.Solution overviewThe IoT Carrier is also a part of the Oplá kit, that in addition to the IoT carrier contains anArduino MKR Wifi 1010, a motion sensor, moisture sensor, USB cable and a protective case .4.Board OperationNote: Please note that in order to operate with the Arduino IoT Carrier, a Mkr Wifi 1010 isrequired.4.1 Getting started - IDEIf you want to program your Arduino IoT carrier while offline you need to install theArduino Desktop IDE [ 1] . To connect the Arduino IoT Carrier to your computer, you’ll need aMicro-B USB cable. This also provides power to the board, as indicated by the LED.4.2 Getting started - Arduino Web EditorAll Arduino boards, including this one, work out-of-the-box on the Arduino Web Editor [ 2] ,by just installing a simple plugin.The Arduino Web Editor is hosted online, therefore it will always be up-to-date with thelatest features and support for all boards. Follow [ 3] to start coding on the browser andupload your sketches onto your board.

4.3 Getting started - Arduino IoT CloudAll Arduino IoT enabled products are supported on Arduino IoT Cloud which allows you toLog, graph and analyze sensor data, trigger events, and automate your home or business.4.4 Sample SketchesSample sketches for the Arduino IoT carrier can be found either in the “Examples” menu inthe Arduino IDE or in the “Documentation” section of the Arduino Pro website [4]4.5 Online resourcesNow that you have gone through the basics of what you can do with the board you canexplore the endless possibilities it provides by checking exciting projects on ProjectHub [ 5] ,the Arduino Library Reference [6] and the online store [7] where you will be able tocomplement your board with sensors, actuators and more4.6 Board RecoveryAll Arduino boards have a built-in bootloader which allows flashing the board via USB. Incase a sketch locks up the processor and the board is not reachable anymore via USB it ispossible to enter bootloader mode by double-tapping the reset button right after powerup.

5.Connector PinoutsDetailed information on the IoT Carrier’s pinouts are available in a separate document:

5.1 Battery TPowerPositive 18650 Battery Terminal5.2 A5PinFunctionTypeDescription1AN5AnalogAnalog Input 52NCNCNot Connected3 5VPower 5.0V power rail4GNDPowerGround5.3 A6PinFunctionTypeDescription1AN6AnalogAnalog Input 62NCNCNot Connected3 5VPower 5.0V power rail4GNDPowerGround5.4 I2CPinFunctionTypeDescription1SCLDigitalI2C Clock Signal2SDADigitalI2C Data Signal3 5VPower 5.0V power rail

4GNDPowerGround5.5 Relay 1/Relay 2PinFunctionTypeDescription1NCSwitchNormally Closed2COMSwitchCommon3NOSwitchNormally Open6. Mechanical information6.1 Board outline/ mounting holes

7. Ratings7.1 Absolute Maximum RatingsSymbolDescriptionMinT MaxVBatt MaxARelay MaxP MaxMaximum thermal limit Maximum input voltage from battery inputMaximum current through relay switchMaximum Power Consumption-303.2-1TypMaxUnit203.7-854.325000 CVAmW8. Certifications8.1 Declaration of Conformity CE DoC (EU)We declare under our sole responsibility that the products above are in conformity with theessential requirements of the following EU Directives and therefore qualify for freemovement within markets comprising the European Union (EU) and European EconomicArea (EEA).ROHS 2 Directive 2011/65/EUConforms to:EN50581:2012Directive 2014/35/EU. (LVD)Conforms to:EN ctive 2004/40/EC & 2008/46/EC & 2013/35/EU, EMFConforms to:EN 62311:20088.2 Declaration of Conformity to EU RoHS& REACH 211 01/19/2021Arduino boards are in compliance with RoHS 2 Directive 2011/65/EU of the EuropeanParliament and RoHS 3 Directive 2015/863/EU of the Council of 4 June 2015 on therestriction of the use of certain hazardous substances in electrical and electronicequipment.1excluding Li-ion battery

SubstanceLead (Pb)Cadmium (Cd)Mercury (Hg)Hexavalent Chromium (Cr6 )Poly Brominated Biphenyls (PBB)Poly Brominated Diphenyl ethers (PBDE)Bis(2-Ethylhexyl} phthalate (DEHP)Benzyl butyl phthalate (BBP)Dibutyl phthalate (DBP)Diisobutyl phthalate (DIBP)Exemptions : No exemptions are claimed.Maximum Limit o Boards are fully compliant with the related requirements of European UnionRegulation (EC) 1907 /2006 concerning the Registration, Evaluation, Authorization andRestriction of Chemicals (REACH). We declare none of the ist-table), the Candidate List of Substancesof Very High Concern for authorization currently released by ECHA, is present in allproducts (and also package) in quantities totaling in a concentration equal or above 0.1%.To the best of our knowledge, we also declare that our products do not contain any of thesubstances listed on the "Authorization List" (Annex XIV of the REACH regulations) andSubstances of Very High Concern (SVHC) in any significant amounts as specified by theAnnex XVII of Candidate list published by ECHA (European Chemical Agency) 1907/2006/EC.8.3 Conflict Minerals DeclarationAs a global supplier of electronic and electrical components, Arduino is aware of ourobligations with regards to laws and regulations regarding Conflict Minerals, specifically theDodd-Frank Wall Street Reform and Consumer Protection Act, Section 1502. Arduino doesnot directly source or process conflict minerals such as Tin, Tantalum, Tungsten, or Gold.Conflict minerals are contained in our products in the form of solder, or as a component inmetal alloys. As part of our reasonable due diligence Arduino has contacted componentsuppliers within our supply chain to verify their continued compliance with the regulations.Based on the information received thus far we declare that our products contain ConflictMinerals sourced from conflict-free areas.

9. FCC CautionAny Changes or modifications not expressly approved by the party responsible forcompliance could void the user’s authority to operate the equipment.This device complies with part 15 of the FCC Rules. Operation is subject to the followingtwo conditions:(1) This device may not cause harmful interference(2) this device must accept any interference received, including interference that maycause undesired operation.FCC RF Radiation Exposure Statement:1. This Transmitter must not be co-located or operating in conjunction with any otherantenna or transmitter.2. This equipment complies with RF radiation exposure limits set forth for an uncontrolledenvironment.3. This equipment should be installed and operated with minimum distance 20cm betweenthe radiator & your body.English:User manuals for licence-exempt radio apparatus shall contain the following or equivalentnotice in a conspicuous location in the user manual or alternatively on the device or both.This device complies with Industry Canada licence-exempt RSS standard(s). Operation issubject to the following two conditions:(1) this device may not cause interference(2) this device must accept any interference, including interference that may causeundesired operation of the device.French:Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareilsradio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :(1) l’ appareil nedoit pas produire de brouillage(2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si lebrouillage est susceptible d’en compromettre le fonctionnement.