Transcription
This is a preview of "BS 8887-220:2010". Click here to purchase the full version from the ANSI store.BS 8887-220:2010BSI Standards PublicationDesign for manufacture,assembly, disassembly andend‑of-life processing (MADE)Part 220: The process ofremanufacture – SpecificationNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWraising standards worldwide
BS 8887-220:2010BRITISH STANDARDThis is a preview of "BS 8887-220:2010". Click here to purchase the full version from the ANSI store.Publishing and copyright informationThe BSI copyright notice displayed in this document indicates when thedocument was last issued. BSI 2010ISBN 978 0 580 68308 4ICS 01.040.01, 01.100.01The following BSI references relate to the work on this standard:Committee reference TDW/4Draft for comment 09/30205838 DCPublication historyFirst published March 2010Amendments issued since publicationDateText affected
BRITISH STANDARDBS 8887-220:2010This is a preview of "BS 8887-220:2010". Click here to purchase the full version from the ANSI store.ContentsForeword ii0Introduction 11Scope 12Normative references 13Terms and definitions 24The remanufacturing process 25Identification and marking 4Bibliography 5List of figuresFigure 1 – Product lifecycle1Summary of pagesThis document comprises a front cover, an inside front cover,pages i to ii, pages 1 to 6, an inside back cover and a back cover. BSI 2010 i
BS 8887-220:2010BRITISH STANDARDThis is a preview of "BS 8887-220:2010". Click here to purchase the full version from the ANSI store.ForewordPublishing informationThis British Standard is published by BSI and came into effect on31 March 2010. It was prepared by Subcommittee TDW/4/7, BS 8887Design for MADE under the authority of Technical Committee TDW/4,Technical product realization. A list of organizations represented onthis committee can be obtained on request to its secretary.Relationship with other publicationsBS 8887 is published in a number of parts, including: Part 1: General concepts, processes and requirements; Part 2: Terms and definitions.Information about this documentDocuments numbered Part 1 to Part 99 are general MADE standards.Documents numbered Part 100 to Part 199 are related to manufactureand assembly. Documents numbered Part 200 to Part 299 are relatedto disassembly and end-of-life.Presentational conventionsThe provisions of this standard are presented in roman (i.e. upright)type. Its requirements are expressed in sentences in which the principalauxiliary verb is “shall”.Commentary, explanation and general informative material is presentedin smaller italic type, and does not constitute a normative element.Contractual and legal considerationsThis publication does not purport to include all the necessary provisionsof a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity fromlegal obligations.ii BSI 2010
BRITISH STANDARDBS 8887-220:2010This is a preview of "BS 8887-220:2010". Click here to purchase the full version from the ANSI store.0 IntroductionThis part of BS 8887 deals with remanufacture and should be read inconjunction with BS 8887-2 as well as Figure 1.Figure 1 Product lifecycleNOTE The likely change in warranty level compared to the original products is given in parentheses.1 ScopeThis part of BS 8887 specifies requirements for the process ofremanufacture and the steps required to change a used product into anas-new product, with at least equivalent performance and warranty ofa comparable new replacement product. The remanufacturing processcan include parts or components to be used in subsequent assembly.This part of BS 8887 is applicable to manufactured products. It is notapplicable to: certain transient products or consumables (e.g. food, fuel); digital media; or commodity materials (e.g. base chemical substances, sand orminerals).2 Normative referencesThe following referenced documents are indispensable for theapplication of this document. For dated references, only the editioncited applies. For undated references, the latest edition of thereferenced document (including any amendments) applies.BS 8887-2:2009: Design for manufacture, assembly, disassembly andend-of-life processing (MADE) – Part 2: Terms and definitions BSI 2010 1
Design for manufacture, assembly, disassembly and end‑ofife processing (MADE)‑l Part 220: The process of remanufacture – Specification BS 888720:2010‑2 This is a preview of "BS 8887-220:2010". Cli
