Transcription
CENTRIFUGAL IMMERSION PUMPSFLUX CENTRIFUGAL IMMERSION PUMPS –QUALITY THAT SETS STANDARDSManufactured at our main plant, these ranges of immersion pumps are theresult of extensive product and process evaluation by our research anddevelopment department.They are a true FLUX product, from conception through to manufacture,assembly and testing. Their design philosophy, and the materials selectedfor their construction make them ideal for applications in the chemical industry,surface treatment, electroplating, printed circuit manufacturing, water treatmentand wastewater treatment.FLUX centrifugal immersion pumps can be used whenever liquids have to betransferred or circulated. They are suitable for use with a wide variety ofacids and alkalis as well as other chemicals, typically coolants, lubricantsand non-flammable solvents.With delivery rates of up to 74 m3/h and delivery heads of maximum 35 mwater column, FLUX centrifugal immersion pumps combine maximum efficiencywith a robust and reliable construction, resulting in a pump that provides theultimate in process security. These are features that you can rely on, each hour,24 hours a day.The mechanical seal types F 620 and F 640 are designed for typical liquid transferoperations, with either stationary or portable variants. These units compliment thewell-proven barrel pumps range and have a higher output and kW-rating.Top of the range, are the sealless units, these pumps complete the range of high output,high reliability immersion pumps. Designed for continuous use with a wide range ofaggressive liquids, from acids to alkalis, the range includes the type F 706 – with onlya sleeve bearing in contact with the liquid – or the types F 716 and F 726 - with asuspended free-flying shaft and no bearings or seals in contact with the liquid.Three-phase drive motors are available as matched power units in kW-ratings from0,37 to 5,5 kW, protected to IP 55 as well as explosion-proof to EEx e II T3for models F 620, F 640, F 706 and F 726.With immersion lengths from 300 to 4000 mm almost every application requirementcan be met. The use of high-class materials such as Hastelloy C and polyvinylidenfluoride,together with polypropylene and stainless steel, are combined with design experienceperfected over decades of pump manufacturing. This guarantees the long service life ofFLUX centrifugal immersion pumps.Detailed information and performance charts are shown on the following pages.To receive a quotation compiled to your application, please could you to fill inthe questionnaire on page 22.2 and return it to us.2
FLUXFLUX TAUCHKREISELPUMPEN – EINSTARKESPUMPENPROGRAMMSAFE, POWERFUL, RELIABLE –THE NEW FLUX RANGEWith 4 different design formats within the vertical centrifugal immersion pump range FLUX offer a cost effective,reliable solution for many liquid transfer and circulating operations. With these pumps FLUX meet the requirementsof the market with their forward-looking designs and the manufacture of high quality products.Type F 706:Type F 726:4 different sizes, seallesvery robust construction with shaftdesign with sleeve bearing,bearing located in a pedestal, versionimmersion length up towith support bars for continuous use,2000 mmsuitable for dry operationType F 620 and F 640:with mechanical seal in verticalType F 716:and horizontal versioncompact design requires littlespace for installation, version withsupport tube or support bars forcontinuous use, suitable for dryoperation2.12.2
2–3IntroductionTable of contents4–5FLUX Centrifugal Immersion Pumps F 620 SSize 15 and 30 in stainless steelfor delivery rates of up to 23 m3/h6–7FLUX Centrifugal Immersion Pumps F 640 PPSize 15, 30, 15 Z and 30 Z in polypropylenefor delivery rates of up to 34 m3/h8–9NEW10 –11FLUX Centrifugal Immersion Pumps F 640 PP and F 640 PVDFSize 185 in polypropylene or polyvinylidenfluoridefor delivery rates of up to 40 m3/hTABLE OF CONTENTSFLUXFLUX CENTRIFUGAL IMMERSION PUMP F 620 SIN STAINLESS STEELSIZEAND30Typical ApplicationsTransferring low flammability liquids up to a viscosity of 2500 mPas (cP)from containers or tanks, either open topped or closed.Suitable for stationary or portable applications.Construction featuresCentrifugal pump in stainless steel consisting of an inner tube and outer tube.The centrifugal impeller in the pump housing is driven by the motor via thedrive shaft. The drive shaft is supported by intermediate bearings within theinner tube, a mechanical seal separates the liquid from the bearings andupper shaft. This construction provides the ultimate in stability, and ensuresthe maximum integrity of the mechanical seal. With an open conical impeller.Three-phase motors in differing kW-ratings are available as a matched power unit.FLUX Centrifugal Pumps F 620 S TR and F 640 PP TRConnection to the pump is made via a flexible coupling.in horizontal version for delivery rates of up to 44 m3/h12–1315FLUX Centrifugal Immersion Pumps F 706 PPSize 135, 185, 230 and 350 in polypropylenefor delivery rates of up to 74 m3/h14–15F 620 S-30with suction strainerFLUX Centrifugal Immersion Pumps F 716 PP and F 716 PVDFSize 115 and 135 in polypropylene or polyvinylidenfluorideCONSTRUCTION FEATURESfor delivery rates of up to 12 m3/h16–17INDETAILFLUX Centrifugal Immersion Pumps F 716 PP and F 716 PVDFSize 185 and 230 in polypropylene or polyvinylidenfluorideflexible couplingfor delivery rates of up to 45 m3/h18–19FLUX Centrifugal Immersion Pumps F 726 PP and F 726 PVDFSize 115 and 135 in polypropylene or polyvinylidenfluoridefor delivery rates of up to 12 m3/h20–21drive shaftFLUX Centrifugal Immersion Pumps F 726 PP and F 726 PVDFSize 185 and 230 in polypropylene or polyvinlydenfluorideinner tubefor delivery rates of up to 45 m3/h22–23outer tubeDimensions of three-phase motorsQuestionnaireThe great range of FLUX pumpsmechanical sealopen conical impeller34
FLUXTECHNICAL DATAPerformance chart FLUX F 620 S-15 and F 620 S-30Dimensions F 620 S-15 and F 620 S-30WCTECHNICAL DATA3015Three-phase motor:dimension X, Ø Y and Zsee page 22301505101520Minimum liquid level whenstarting the pump.Also valid for variant 1.25Variant 1with suction strainerMeasured values 10% determined with water (20 C). Nominal speed n 2850 rpmIn determining the absorbed kW of the motor, multiply the absorbed kW shown in the above diagram with thespecific gravity of the liquid to be pumped.1Basic modeldimension e max. 3000 mm4.14.2
CENTRIFUGAL IMMERSION PUMP F 620 S, THREAD ON OUTLET G 11/4 A (BSP 11/2” MALE), WITHOUT DRIVE MOTORType / SizeF 620 S-15F 620 S-30Delivery rate Q max.19 m3/h23 m3/hDelivery head H max.10 m water column12 m water columnViscosity max.2500 mPas (cP)2500 mPas (cP)Temperature max.100 C100 CSeal typemechanical seal in ceramic oxide, o-rings in FPMMaterialshaft in stainless steel 1.4571/316 Ti, seal in FPMImpellerconical impeller in polypropylene (version in stainless steel on request)Pump housingØ 140 mmØ 140 mmPart No.Immersion length700 mm620 23 001621 23 0011000 mm620 23 002621 23 0021500 mm620 23 003621 23 003Part numbers for immersion length 300 to 3000 mm (in steps of 100 mm) on request.Accessories:Part No.Mounting flange in stainless steel 1.4571/316 Tioutside Ø 265 mm, pitch circle Ø 225 mm, 8 bores Ø 18 mm each947 14 005Suction strainer in stainless steel 1.4571/316 Ti001 10 23211Hose connection in stainless steel, complete with nut in brass G 1 /2 (BSP 1 /2 female)for hose inside diameter DN 25959 04 002for hose inside diameter DN 32959 04 003for hose inside diameter DN 38959 04 004DRIVE MOTORSFORCENTRIFUGAL IMMERSION PUMP F 620 SThree-phase motors protected to IP 55, with motor protection switch or cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Version withmotor protection switchVersion withcable terminal box0,75 kW230/400 V50 Hz2850 rpm001 00 046001 00 0061,1 kW230/400 V50 Hz2850 rpm001 00 047001 00 0071,5 kW230/400 V50 Hz2850 rpm001 00 048001 00 0082,2 kW230/400 V50 Hz2850 rpm001 00 049001 00 0093,0 kW400 V50 Hz2850 rpm001 00 050001 00 0104,0 kW400 V50 Hz2850 rpm001 00 051001 00 011Three-phase motors explosion-proof to EEx e II T3 with cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Three-phase motorwith cable terminal boxMotor protection switchEEx de II C T6 to be mountedon the carrying handle0,75 kW230/400 V50 Hz2850 rpm001 00 066936 06 1181,1 kW230/400 V50 Hz2850 rpm001 00 067936 06 1181,5 kW230/400 V50 Hz2850 rpm001 00 068936 06 1192,0 kW230/400 V50 Hz2850 rpm001 00 069936 06 1192,5 kW400 V50 Hz2850 rpm001 00 070936 06 1203,3 kW400 V50 Hz2850 rpm001 00 071936 06 120Accessories:Part No.Carrying handle for three-phase motors up to 3,0 kW001 10 504Carrying handle for three-phase motors up 4,0 kW001 10 531Carrying handle for three-phase motors explosion-proof up to 3,3 kW001 10 567SCOPECENTRIFUGAL IMMERSION PUMPS F 620 SFLUXFLUX CENTRIFUGAL IMMERSION PUMP F 640 PP IN POLYPROPYLENESIZE 15, 30, 15 Z AND 30 ZTypical applicationsTransferring low flammability liquids up to a viscosity of 2500 mPas (cP)from containers, tanks, either open topped or closed.Transferring corrosive liquids in chemical processing and engineering,metal-working and electroplating together with water treatment andwaste water treatment. Suitable for stationary or portable application.Construction featuresVertical centrifugal immersion pump in polypropylene consistingof an inner tube and outer tube.The centrifugal impeller in the pump housing is driven by the motorvia the drive shaft. The drive shaft is supported by intermediate bearingswithin the plastic sleeved steel inner tube, a mechanical seal separatingthe liquid from the bearings and upper shaft. This construction providesthe ultimate in stability, preventing elongation of the plastic at high temperaturesand ensures the maximum integrity of the mechanical seal.With an open conical impeller or a closed centrifugal impeller (Z).The liquid is delivered between the inner and outer tubes to the pump outlet.Three-phase motors in differing kW-ratings are available as a matched power unit.Connection to the pump is made via a flexible coupling.F 640 PP-30with suction strainerCONSTRUCTION FEATURESINDETAILflexible couplingdrive shaftsteel cored inner tubeouter tubemechanical sealOF SUPPLYopen conical impellerA complete vertical centrifugal immersion pump consists of: drive motor, pump and necessary accessories.closed centrifugalimpeller (Z)Weight per pump: 15 – 45 kg depending on the pump size, immersion length and motor kW.56
FLUXTECHNICAL DATAPerformance chart F 640 PP-15, F 640 PP-30, F 640 PP-15 Z and F 640 PP-30 ZDimensions F 640 PP-15, F 640 PP-30, F 640 PP-15 Z and F 640 PP-30 ZWCTECHNICAL DATAThree-phase motor:dimension X, Ø Y and Zsee page 2230Z30315Z230151530Z1Minimum liquid level whenstarting the pump.Also valid for variant 1.15Z00510152025303540Variant 1with suction strainerdimension e 38 mmMeasured values 10% determined with water (20 C). Nominal speed n 2850 rpmIn determining the absorbed kW of the motor, multiply the absorbed kW shown in the above diagramwith the specific gravity of the liquid to be pumped.1Basic modeldimension e max. 4000 mm6.16.2
FLUXType / SizeF 640 PP-15F 640 PP-30F 640 PP-15ZF 640 PP-30ZDelivery rate Q max.17 m3/h29 m3/h21 m3/h34 m3/hDelivery head H max.8 m water column10 m water column10 m water column11 m water columnViscosity max.2500 mPas (cP)2500 mPas (cP)150 mPas (cP)150 mPas (cP)Temperature max.50 C50 C50 C50 CSeal typemechanical seal in ceramic oxide / SiC, o-rings in FPMMaterialshaft in Hastelloy C, seals in FPMImpelleropen conical impeller in PPPump housingØ 148 mmMounting flange*Ø 148 mmclosed centrifugal impeller in PPØ 148 mmØ 148 mmoutside Ø 265 mm, pitch circle Ø 225 mm, 8 bores Ø 18 mm eachPart No.700 mmImmersion length1000 mmDimension e1500 mm640 41 407640 41 607640 41 507640 41 707640 41 410640 41 610640 41 510640 41 710640 41 415640 41 615640 41 515640 41 715Part numbers for immersion length 400 to 4000 mm (in steps of 100 mm) on request.* also available without mounting flange for portable application.Accessories:Part No.Suction strainer in polypropylene001 10 235Hose connection in polypropylene, complete with nut G 21/4 (BSP 21/4 female)for hose inside diameter DN 32959 04 098for hose inside diameter DN 38959 04 099for hose inside diameter DN 50959 04 100DRIVE MOTORSFORCENTRIFUGAL IMMERSION PUMP F 640 PPThree-phase motors protected to IP 55, with motor protection switch or cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Version withmotor protection switchVersion withcable terminal box0,75 kW230/400 V50 Hz2850 rpm001 00 046001 00 0061,1 kW230/400 V50 Hz2850 rpm001 00 047001 00 0071,5 kW230/400 V50 Hz2850 rpm001 00 048001 00 0082,2 kW230/400 V50 Hz2850 rpm001 00 049001 00 0093,0 kW400 V50 Hz2850 rpm001 00 050001 00 0104,0 kW400 V50 Hz2850 rpm001 00 051001 00 011Three-phase motors explosion-proof to EEx e II T3 with cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Version withcable terminal boxMotor protection switchEEx de II C T6 to be mountedon the carrying handle0,75 kW230/400 V50 Hz2850 rpm001 00 066936 06 1181,1 kW230/400 V50 Hz2850 rpm001 00 067936 06 1181,5 kW230/400 V50 Hz2850 rpm001 00 068936 06 1192,0 kW230/400 V50 Hz2850 rpm001 00 069936 06 1192,5 kW400 V50 Hz2850 rpm001 00 070936 06 1203,3 kW400 V50 Hz2850 rpm001 00 071936 06 120Accessories:Part No.Carrying handle for three-phase motors up to 3,0 kW001 10 504Carrying handle for three-phase motors up 4,0 kW001 10 531Carrying handle for three-phase motors explosion-proof up to 3,3 kW001 10 567SCOPEFLUX CENTRIFUGAL IMMERSION PUMP F 640 PP AND F 640 PVDFIN POLYPROPYLENE OR POLYVINYLIDENFLUORIDENEWSIZE 185CENTRIFUGAL IMMERSION PUMP F 640 PPCENTRIFUGAL IMMERSION PUMP F 640 PP, THREAD ON OUTLET G 21/4 A (BSP 21/4” MALE), WITHOUT DRIVE MOTORTypical applicationsTransferring low flammability liquids up to a viscosity of 2500 mPas (cP)from containers, tanks, either open topped or closed.Transferring corrosive liquids in chemical processing and engineering,metal-working and electroplating together with water treatment andwaste water treatment. Suitable for stationary or portable application.Construction featuresVertical centrifugal immersion pump for stationary application.The centrifugal impeller in the pump housing is driven by the motor via the drive shaft.The drive shaft is supported by intermediate bearings within the plastic sleeved steelinner tube, a mechanical seal separating the liquid from the bearings and upper shaft.This construction provides the ultimate in stability, preventing elongation of the plasticat high temperatures and ensures the maximum integrity of the mechanical seal.This pump design does not have a separate discharge tube. Immediatelyafter the pump housing the liquid is fed back into the outer tube and deliveredto the outlet connection between the inner and outer tubes.A range of carefully chosen impeller diameters, together with a range ofthree-phase motors in differing kW-ratings, ensures the optimum selectionof pumps to meet the specific operating requirements.Connection of pump and motor is made via a flexible coupling.F 640 PP-185CONSTRUCTION FEATURESINDETAILflexible couplingouter tubesteel cored inner tubepump shaftmechanical sealcentrifugal impeller in differing diametersspiral housingOF SUPPLYA complete vertical centrifugal immersion pump consists of: drive motor, pump and necessary accessories.cover with circlipWeight per pump: 15 - 60 kg depending on the pump size, immersion length and motor kW.78
FLUXTECHNICAL DATATECHNICAL DATAPerformance chart F 640 PP-185 and F 640 PVDF-185Dimensions F 640 PP-185 and F 640 PVDF-185WCØ 140Ø 130Ø 120Ø 110Three-phase motor:dimension X, Ø Y and Zsee page 22Ø 100Minimum liquid level whenstarting the pump.Also valid for the variants 1, 2 and 3Ø 140Ø 130Ø 120Ø 10001020Variant 1with extension tubeØ 1103040Variant 2with suction strainer50Variant 3with extension tubeand suction strainerMeasured values 10% determined with water (20 C). Nominal speed n 2850 min-1In order to achieve the desired output, centrifugal impellers in diameters of 100 to 140 mm are available.1In determining the absorbed kW of the motor, multiply the absorbed kW shown in the above diagramwith the specific gravity of the liquid to be pumped.Basic modeldimension emax. 4000 mm8.18.2Dimension p max. 1500 mm23
CENTRIFUGAL IMMERSION PUMP F 640 PP IN POLYPROPYLENETHREAD ON OUTLET G 21/4 A (BSP 21/4“ MALE), WITHOUTType / SizeANDF 640 PVDFINPOLYVINYLIDENFLUORIDE,DRIVE MOTORF 640 PP-185F 640 PVDF-1853Delivery rate Q max.40 m /h40 m3/hDelivery head H max.23 m water column23 m water columnViscosity max.150 mPas (cP)150 mPas (cP)Temperature max.60 C80 CSeal typemechanical seal in ceramic oxide /SiC, o-rings in FPMMaterialshaft in Hastelloy C, seals in FPMCentrifugal impellerØ 100 – 140 mm in PP or PVDFPump housingØ 249 mmMounting flangeØ 249 mmoutside Ø 340 mm, pitch circle Ø 295 mm, 4 bores Ø 22 mm eachPart No.1000 mmImmersion length1500 mmDimension e2000 mm640 41 210640 61 210640 41 215640 61 215640 41 220640 61 220Part numbers for immersion length 400 to 4000 mm (in steps of 100 mm) on request.Accessories:Part No.Extension tube in PP or PVDF in steps of 100 mm. Dimension p up to max. 1500 mmSuction strainer in PP or PVDF welded onto the cover of the pump housing or onto the extension tubeHose connection in polypropylene, complete with nut G 21/4 (BSP 21/4“ female)for hose inside diameter DN 32959 04 098for hose inside diameter DN 38959 04 099for hose inside diameter DN 50959 04 10011Hose connection in polyvinylidenfluoride, complete with nut G 2 /4“ (BSP 2 /4 female)for hose inside diameter DN 32959 04 104for hose inside diameter DN 38959 04 105for hose inside diameter DN 50959 04 096DRIVEMOTORS FORCENTRIFUGAL IMMERSION PUMPS F 640 PPANDF 640 PVDFThree-phase motors protected to IP 55, with motor protection switch or cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Version withmotor protection switchVersion withcable terminal box0,75 kW230/400 V50 Hz2850 rpm001 00 046001 00 0061,1 kW230/400 V50 Hz2850 rpm001 00 047001 00 0071,5 kW230/400 V50 Hz2850 rpm001 00 048001 00 0082,2 kW230/400 V50 Hz2850 rpm001 00 049001 00 0093,0 kW400 V50 Hz2850 rpm001 00 050001 00 0104,0 kW400 V50 Hz2850 rpm001 00 051001 00 011Three-phase motors explosion-proof to EEx e II T3 with cable terminal boxCapacityVoltageFrequencyNominal speedP2Part No.Part No.Version withcable terminal boxMotor protection switchEEx de II C T6 to be mountedon the carrying handle0,75 kW230/400 V50 Hz2850 rpm001 00 066936 06 1181,1 kW230/400 V50 Hz2850 rpm001 00 067936 06 1181,5 kW230/400 V50 Hz2850 rpm001 00 068936 06 1192,0 kW230/400 V50 Hz2850 rpm001 00 069936 06 1192,5 kW400 V50 Hz2850 rpm001 00 070936 06 1203,3 kW400 V50 Hz2850 rpm001 00 071936 06 120SCOPEOF SUPPLYA complete vertical centrifugal immersion pump consists of: drive motor, pump with mounting flange and necessary accessories.CENTRIFUGAL IMMERSION PUMP F 640 PP AND F 640 PVDFFLUXFLUX CENTRIFUGAL PUMPS F 620 S TRIN HORIZONTAL VERSIONF 640 PP TRTypical applicationsTransferring low flammability liquids up to a viscosity of 2500 mPas (cP)from containers or tanks, either open topped or closed.The pump is used either horizontally mounted onto a base plate or fixed vertically.Construction featuresCentrifugal pump in horizontal version in stainless steel or polypropylene,consisting of an inner tube and outer tube.The centrifugal impeller in the pump housing is driven by the motor via the drive shaftThe drive shaft is supported by intermediate bearings within inner tube, a mechanicalseal separates the liquid from the bearings and upper shaft.The PP version has a steel cored PP inner tube. This construction provides the ultimatein stability, preventing elongation of the plastic at high temperatures and ensuresthe maximum integrity of the mechanical seal.With an open conical impeller or a closed centrifugal impeller (Z)Depending on the model, suction and discharge sidesare fitted with threaded or flanged connections.Three-phase motors in differing kW-ratings are available asa matched power unit. Connection to the pump is madevia a flexible coupling.F 620 S-30 TR mounted on base plateF 640 PP-30 TR mounted on base plateF 640 PP-230 TR mounted on base plateWeight per pump: 20 – 60 kg depending on the pump size, immersion length and motor kW.9AND10
FLUXTECHNICAL DATAPerformance chart F 620 S-30 TR,Dimensions F 620 S-30 TR with thread connectionWCTECHNICAL DATAThree-phase motor: dimension X, Ø Y and Z see page 223030Dimensions F 640 PP-30 TR with thread connection0105201525Three-phase motor: dimension X, Ø Y and Z see page 22WCPerformance chart F 640 PP-30 TR,3032301Dimensions F 640 PP-30 TR with flange connectionThree-phase motor: dimension X, Ø Y and Z see page 2200510152025303540WCPerformance chart F 640 PP-230 TR4035Ø 160Ø 15030Ø 14025Ø 13020Dimensions F 640 PP-230 TR with flange connectionØ 120Ø 16015Ø 100103Ø 150Ø 140Ø 1102Ø 1305Ø 100Ø 110Three-phase motor: dimension X, Ø Y and Z see page 22Ø 120100051015202530354045Measured values 10% determined with water (20 C). Nominal speed n 2850 rpmIn determining the absorbed kW of the motor, multiply the absorbed kW shown in the abovediagram with the specific gravity of the liquid to be pumped.10.110.2
CENTRIFUGAL PUMP F 620 S TRSTAINLESS STEEL,INWITHOUT DRIVE MOTORType / SizeF 620 S-30 TRDelivery rate Q max.23 m3/hDelivery head H max.12 m water columnViscosity max.2500 mPas (cP)Temperature max.100 CSeal typemechanical seal in ceramic oxide, o-rings in FPMMaterialshaft in stainless steel 1.4571/316 Ti, seals in FPMImpelleropen conical impeller in polypropylene (version in stainless steel on request)Suction sidethread G 2 A (BSP 2“ male)Discharge sidethread G 11/2 A (BSP 11/2“ male)Part No.620 25 502Accessoires:Part No.Base plate in aluminium alloy001 15 002Hose connection in stainless steel, complete with nut G 11/2 (BSP 11/2“for hose inside diameter DN 25for hose inside diameter DN 32for hose inside diameter DN 38female)959 04 002959 04 003959 04 004CENTRIFUGAL PUMPF 640 PP TRINPOLYPROPYLENE,WITHOUT DRIVE MOTORType / SizeF 640 PP-30 TRDelivery rate Q max.29 m3/hDelivery head H max.10 m water columnViscosity max.2500 mPas (cP)Temperature max.50 CSeal typemechanical seal in ceramic oxide /SiC, o-rings in FPMMaterialshaft in Hastelloy C, seals in FPMImpelleropen conical impeller in PPSuction sidethread G 2 A (BSP 2“ male)11flange DN 65, PN 10Discharge sidethread G 2 /4 A (BSP 2 /4“ male)flange DN 50, PN 10Part No.640 41 601640 41 600CENTRIFUGAL PUMP F 640 PP TRIN POLYPROPYLENE, WITHOUT DRIVE MOTORType / SizeF 640 PP-230 TRDelivery rate Q max.44 m3/hDelivery head H max.33 m water columnViscosity max.150 mPas (cP)Temperature max.60 CSeal materialmechanical seal in ceramic oxide/SiC, o-rings in FPMMaterialshaft in Hastelloy C, seals in FPMImpellerØ 100 – 160 mm in PPSuction sideflange DN 65, PN 10; outside Ø 185 mm, p.c.Ø 145 mm, 4 bores Ø 18 mm eachDischarge sideflange DN 50, PN 10; outside Ø 165 mm, p.c.Ø 125 mm, 4 bores Ø 18 mm eachPart No.640 41 300Accessories:Part No.Base plate in aluminium alloy for F 640 PP-30 TR001 15 001Base plate in polypropylene for F 640 PP-30 TR and F 640 PP-230 TR001 15 023CENTRIFUGAL PUMPS IN HORIZONTAL VERSIONFLUXFLUX CENTRIFUGAL IMMERSION PUMP F 706 PPSIZE 135, 185, 230 AND 350Transfer of corrosive liquids in the chemical industry and all aspects ofchemical engineering together with any application that requires the safeand economical transfer, or circulation, of acids and alkalis or otherchemical fluids, with or without solids in suspension.Construction featuresVertical centrifugal immersion pump for stationary application.The robust pump housing is solidly welded to the support tube.A sleeve bearing, which is lubricated by the liquid, allows immersion lengthsof up to 1000 mm, and on the pump size 230, with additional intermediatebearings, even up to 2000 mm.A large polpypropylene-coated drive shaft together with the use of athick-walled support tube ensures a very smooth running pump.This type of construction prevents the rotating components from coming tocontact with the pump housing and guarantees a long service life andextended maintenance intervals, even in the case of continuous use.A range of carefully chosen impeller diameters, together with a range ofthree-phase motors in differing kW-ratings, ensures the optimum selectionof pumps to meet the specific operating requirements. Connection of pumpand motor is made via a flexible coupling.F 706 PP-350CONSTRUCTION FEATURESINDETAILflexible couplinglarge pump shaftwith protective coating in PPslide bearing lubricated by the liquidwearing bushing in HCDrive motors see page 9centrifugal impeller in differing diametersOF SUPPLYA complete centrifugal pump in horizontal version consists of drive motor, pump and base plate.cover with circlip on pump size 185 and 230Weight per pump including base plate: 9 – 50 kg depending on pump size and motor kW.11POLYPROPYLENETypical applicationsHose connection in polypropylene, complete with nut G 21/4 (BSP 2 1/4“ female)for hose inside diameter DN 32959 04 098for hose inside diameter DN 38959 04 099for hose inside diameter DN 50959 04 100SCOPEIN12
FLUXTECHNICAL DATAPerformance chart F 706 PP-135Dimensions F 706 PP-135WCTECHNICAL DATA20Measured values18 10% determined with water (20 C).Ø 10016Nominal speed n 2850 rpm14Three-phase motors:dimension X, Ø Y and Zsee page 22Ø 90In order to obtain the desired12Ø 8010output, centrifugal impellers inØ 1006Variant 2with suction strainer0.4In determining the absorbed0.2kW of the motor, multiply the0.0absorbed kW shown in the aboveVariant 3with extension tubeand suction strainer0.6Ø 904Ø 8020012345678910111213diagram with the specific gravityPerformance chart F 706 PP-18525Variant 1with extension tubediffering diameters are available.0.88WCDimensions F 706 PP-185of the liquid to be pumped.Ø 140123123Ø 13020Ø 12015Ø 110Ø 100103Ø 1405Ø 100Ø 110Basic modeldimension emax. 1000 mm2Ø 130Ø 1201000510152025303540Dimension pmax. 1000 mmBasic modeldimension emax. 1000 mmDimension pmax. 1500 mm45WCPerformance chart F 706 PP-2304035Dimensions F 706 PP-230Ø 160Dimensions F 706 PP-350Ø 15030Ø 14025Three-phase motors:dimension X, Ø Y and Zsee page 22Ø 130420Ø 160153Ø 150Ø 14010Minimum or maximumliquid level when startingthe pump.Also valid for the variants1, 2 and 32Ø 1301500051015202530354045WCPerformance chart F 706 PP-35025Nominal speed n 1450 rpmØ 2501Ø 24020Ø 23015Ø 220Ø 210Ø 20010Ø 250 Ø 240Ø 230Basic modeldimension emax. 2000 mm10012.120304050607012321034Ø 220Ø 210Ø 2005028012.2Dimension pmax. 1500 mmBasic modeldimension emax. 1000 mmDimension pmax. 1500 mm3
CENTRIFUGAL IMMERSION PUMP F 706 PP IN POLYPROPYLENE, VERSION WITH SUPPORT TUBE, WITHOUT DRIVE MOTORType / SizeF 706 PP-135F 706 PP-185F 706 PP-230F 706 PP-350Delivery rate Q max.12 m3/h43 m3/h44 m3/h74 m3/hDelivery head H max.15 m water column23 m water column33 m water column23 m water columnViscosity max.150 mPas (cP)150 mPas (cP)150 mPas (cP)150 mPas (cP)Temperature max.60 C60 C60 C60 CSeal materialno seals in contact with the liquidMaterialshaft in stainless steel 1.4571/316 Ti with protective coating in PP, slide bearing in hard carbon or fluorosintCentrifugal Impeller in PPØ 80 – 100 mmØ 100 – 140 mmØ 130 – 160 mmØ 200 – 250 mmPump housingØ 174 mmØ 249 mmØ 264 mmØ 417 mmMounting flange in PPoutside Ø 250 mmoutside Ø 340 mmoutside Ø 340 mmoutside Ø 500 mmThread on outletG 11/2 A (BSP 11/2“ male)G 21/4 A (BSP 21/4“ male) G 21/4 A (BSP 21/4“ male)G 23/4 A (BSP 23/4“ male)Motor capacity P 20,37 – 0,75 kWn 2850 rpm1,5 – 4,0 kWn 2850 rpm3,0 – 5,5 kWn 1450 rpm3,0 – 5,5 kWn 2850 rpmPart No.Immersion lengthDimension e500 mm706 41 105706 41 205706 41 305706 41 405700 mm706 41 107706 41 207706 41 307706 41 4071000 mm706 41 110706 41 210706 41 310706 41 410Accessories:Extension tube in PP in steps of 100 mm.Dimension p up to max. 1000 mm at size 135 and up to 1500 mm at sizes 185, 230 and 350.Suction strainer in PP welded onto the cover of the pump housing or onto the extension tube.DRIVEMOTORS FORCENTRIFUGAL IMMERSION PUMP F 706 PPThree-phase motors protected to IP 55, with cable terminable boxCapacity P 2Flange ØVoltageFrequencyNominal speedPart No.0,37 kW120 mm230/400 V50 Hzn 2850 rpm001 00 0040,55 kW120 mm230/400 V50 Hzn 2850 rpm001 00 0050,75 kW120 mm230/400 V50 Hzn 2850 rpm001 00 0191,5 kW160 mm230/400 V50 Hzn 2850 rpm001 00 0082,2 kW160 mm230/400 V50 Hzn 2850 rpm001 00 0093,0 kW160 mm400 V50 Hzn 2850 rpm001 00 0104,0 kW160 mm400 V50 Hzn 2850 rpm001 00 0115,5 kW160 mm400 V50 Hzn 2850 rpm001 00 0153,0 kW160 mm400 V50 Hzn 1450 rpm001 00 5304,0 kW160 mm400 V50 Hzn 1450 rpm001 00 5115,5 kW160 mm400 V50 Hzn 1450 rpm001 00 532Three-phase motors explosion-proof to EEx e II T3 with terminal box on request.SCOPECENTRIFUGAL IMMERSION PUMP F 706 PPFLUXFLUX CENTRIFUGAL IMMERSION PUMP F 716 PP AND F 716 PVDFIN POLYPROPYLENE OR POLYVINYLIDENFLUORIDESIZE 115 AND 135Typical applicationsTransferring and circulating of neutral or corrosive liquids in thechemical industry and chemical engineering, electroplating industry,steel or stainless steel pickling plants, flue gas decontamination,exhaust air purification, water and waste water treatment.Construction featuresVertical centrifugal immersion pump for stationary application. With acompact design requiring very little head room above the mounting flange.This design uses a three-phase motor with extended shaft, especiallyallowing the pump to use the motor shaft. All wetted parts are made in PP or PVDF.The robust support tube (bars) solidly connected to the mounting flangeensures a very smooth running, prevents the rotating elements from makingcontact with the pump housing and guarantees a very long service life,even in case of continuous use.As ne
With these pumps FLUX meet the requirements of the market with their forward-looking designs and the manufacture of high quality products. FLUX 2-3 4-5 6-7 8-9 10-11 12-13 14-15 16-17 18-19 20-21 22-23 Introduction Table of contents FLUX Centrifugal Immersion Pumps F 620 S
