Transcription
Powerline ModulesGreen PHY ModuleThe module is a HomePlug Green PHY Powerline Communications (PLC)transceiver/modem.Provides an integrated Powerline communications solution formicrocontroller based embedded system.Communication is possible over any 2 wire system AC, DC or Dry wire.Key Features & Benefits Based on Qualcomm Atheros QCA7000 chip Compliant HomePlug Green PHY 1.1 specification Fully interoperable with HomePlug AV and IEEE 1901 compliantproducts Host interface type depend on the module variant: UART, SPI orUART-AT Supports OFDM (ROBO) mode modulation, with PHY data rates upto 10Mbps 128-bit AES Link Encryption with key management for securepower line communications Integrates core components necessary to add powerlinecommunication functionality to any embedded system at low cost Supports large 32 node unicast networks - up to 254 broadcastmode devices per AVLN with up to 16 overlapping AVLNs Commercial temperature range (Industrial option available uponrequest) Powered from single 3.3 VDC rail Ideal for Smart Grid applicationsModelsPart NumberTemp RangeInterfaceMarket0804-5000AG00 C – 70 CUART-ATWorldwide0804-5000AG10 C – 70 CSPIWorldwide0804-5000AG20 C – 70 CUARTWorldwideBel Modules28 Turkey Court, Turkey Mill, Ashford RoadMaidstone ME14 5PP UK 44 1622 757 395techhelp@belf.combelfuse.com 2020 Bel Power Solutions, Inc.Rev PC[1]
Powerline ModulesGreen PHY ModuleBlock DiagramModule pinoutsModule connectivity is provided via J1, J2 and J3 gold pin headers.J1 - 8 way 2.54mm pitch gold pin headerPin NumberPin NameTypeDescription1VDDPWR 3.3V2VDDPWR 3.3V3VSSPWRGround4RESET#IResets powerline IC when low5RESERVED [1]PWRReserved pin6GPIO0I/OStrap0; Push-button7GPIO1I/OStrap18GPIO2I/OStrap2; LED: Powerline Tx/Rx Link[1] Leave reserved pin disconnectedtechhelp@belf.combelfuse.com[2]
Powerline ModulesGreen PHY ModuleJ2 - 8 way 2.54mm pitch gold pin headerPin NumberPin NameTypeDescription1VSSPWRGround2GPIO3I/OStrap3; LED: Power3GPIO4I/OUART: - / SPI: INTR4GPIO5I/OUART: RTS[*] / SPI: CLK5GPIO6I/OUART: CTS[*] / SPI: CS6GPIO7I/OUART: TX / SPI: DO7GPIO8I/OUART: RX / SPI: DI8VSSPWRGroundJ3 - 2 way 7.62mm pitch gold pin headerPin NumberPin NameTypeDescription1AC NEUTRALPLPowerline communication medium[2]2AC LINEPLPowerline communication medium[2][2] Voltage rating: 250VAC (50/60Hz)Strap ConfigurationThe Powerline chipset boot options are selected by the initial condition of GPIO pins. If a GPIO pin is not used but theinternal strapping resistor sets the booting option incorrectly, then the pin must be pulled high or low to the correctbooting option by an external resistor. This resistor can be 10k-Ohms down to 3.3k-Ohms. Connecting GPIO directly toground or VDD is not permitted.StrapInternalPull Up/DownDescriptionTypicalConfigurationStrap0Pull UpPull Up - Load firmware from flash devicePull UpStrap1Pull UpMust be pulled-downPull DownStrap2Pull DownPull Up - Burst command/dataPull UpStrap3Pull DownMust be pulled-downPull Downtechhelp@belf.combelfuse.com[3]
Powerline ModulesGreen PHY ModuleLED and Push-button StrappingFigure 1 LED Strapping for GPIO Pull-downFigure 2 LED Strapping for GPIO Pull-upFigure 3 Push-button Strapping for GPIO Pull-downFigure 4 Push-button Strapping for GPIO Pull-upGeneral SpecificationsSymbolParameterTest Conditions[1]VDDSupply voltageVILLow-level input voltageVIHHigh-level input voltageMinMaxUnits3.133.45V0.8V2.0[2]VVOLLow-level output voltageIOL 4 mA, 12 mAVOHHigh-level output voltageIOH -4 mA, -12 mA [3]2.4VIILLow-level input currentVI Gnd-1μAIIHHigh-level input currentVI 3.3 VIOZHigh-impedance output currentGnd VI 3.3 VTopOperating temperature range [4][1][2][3][4]0.4V1μA-1 1μA0-40 70 85 CA typical supply current, assuming a nominal operation of 50% transmit and 50% receive duty cycle, is 200 mA.IOL 12 mA for all GPIOs. IOL 4 mA for all other digital interfaces.IOH -12 mA for all GPIOs. IOH -4 mA for all other digital interfaces.Standard module is available in commercial temperature range (industrial is an option)Power supply should be capable to provide from 1.3 to 1.6 Watts. These power levels provide a higher power margin than required in normaloperation.techhelp@belf.combelfuse.com[4]
Powerline ModulesGreen PHY ModuleDimensionsWidth: 30.9mm, Length: 44.3mm, Height: 14.3mmAll specifications subject to change without notice.techhelp@belf.combelfuse.com[5]
VDD Supply voltage [1] 3.13 3.45 V VIL Low-level input voltage 0.8 V VIH High-level input voltage 2.0 V VOL Low-level output voltage IOL 4 mA, 12 mA [2] 0.4 V VOH High-level output voltage IOH -4 mA, -12 mA [3] 2.4 V IIL Low-level input current VI Gnd -1 μA IIH High-level input current VI 3.3 V 1 μA
