Transcription
CHEMFIX 500 - Pure EpoxyFeatures and Benefits Version 25/9/2017High bond strength with High load resistanceUsed with all grades of threaded rod and rebar in accordance with TR029Ideal for deep embedment installationsUsed in non-cracked and cracked concreteUsed in dry and wet concrete and also in woodUsed in flooded holesUsed for overhead applicationsETA approved for diamond drilled holesIdeal for elevated temperatures - temperature ranges I, II and IIIETA approved for rebar installations under TR023 and EN1992-1-1:2004 EC2Zero shrinkage enables large diameter installationsETA approved for Seismic Loads C2 Manual cleaning up to 20mm diameter and embedment depths of 240mm Independently tested and approved - anchor life 50 yearsContentsPAGE 1 - Features and BenefitsPAGE 2 - Typical characteristic and design resistance performance with 5.8 gradestudding and associated installation dataPAGE 3 - Design Resistance used with various stud strengths,material and rebar.PAGE 4 - Characteristic and Design load resistances based on characteristicbond strengths for hef 4d (minimum embedment) to 20dPAGE 5 - Bond Strength FactorsPAGE 6 - Characteristic and Design load resistances for REBAR based oncharacteristic bond strengths for hef 4d (minimum embedment) to 20dPAGE 7 - Bond Strength Factors for REBARPAGE 8 - Material properties for threaded rods and rebarPAGE 9, 10, 11 - Post Installed Rebar valuesPAGE 12 - Tension Edge and Spacing reduction factorsPAGE 13 - Curing Time / Temperature RangePAGE 14 - Installation parameters: drilling hole cleaning and installationShelf Life and StorageThis product should be stored between 5 C & 25 C.The Shelf life of the product is 24 months from the manufacture date.IMPORTANT The information and data given is based on our own experience, research and testing and is believed to be reliable and accurate.However, as we cannot know the varied uses to which its products may be applied, or the methods of application used, no warranty as to thefitness or suitability of its products is given or implied. It is the users responsibility to determine suitability of use. For further information please contactOur Technical Department.Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyProduct DescriptionChemfix 500 is a 2 component high strength pure epoxy chemical anchoring resin system. It is designedfor deep embedment and large diameter holes due to its zero shrinkage, and longer working times.For diamond drilled holes, with rebar, and in areas of high chemical exposure eg. Seasalt and swimming pools.Available in Sizes: 385ml Cartridge or 585ml Cartridge.Specific BenefitsApprovals Long working times Diamond drilled holes ETA Option 1 ETAG 001 for cracked concrete with studs and rebar TR029 High loads possible Zero shrinkage ETA Option 1 ETAG 001 for rebar TR023 : Approved for Seismic Loads C2 High chemical resistance European approved F120 Fire Test report ICC-ES Approval ESR 3853 Use with potable water Fire approved BS6920 for use with potable water WRAS Approved 1309522 Fixing studs in wood Studs and rebar ETA approved in flooded holes, wet and dry concrete 24 Month shelf life A Rating VOC content Tested according to LEED 2009 EQ c4.1, SCAQMD rule 1168 (2005).Typical characteristic and design resistance performance with 5.8 grade studding and associated installation eristic 0 steel failureDesign ended Load(kN)Characteristic 72202.38Min EdgeHoleHoleand concretefixtureTorqueScr,NCcr,VCmin, 20280600130300660150340720Table notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyDesign Resistance used with various stud strengths, material and rebar.5.8 Grade Steel StuddingFd,sStudHoleEmbedment depth hefDiameter Diameter(mm)(mm)60708081012.6 12.7101215.7 18.3 54060066072022.0 25.1 28.3 1831.4 35.3 39.2 43.1 47.1 51.0 54.413954.42233.2 37.3 41.5 45.6 49.8 53.9 58.1 66.4 82.9 84.920584.92428285122.4273053.2 58.0 62.9 67.7 77.4 96.7 116.1 135.4 154.7 159.1329159.1303564.5 69.8 75.2 86.0 107.5 128.9 150.4 171.9 194.5362194.53338364043.0 47.3 51.6 55.9 60.2 68.8 86.0 103.2 120.4 122.471.4 76.9 87.9 109.9 131.9 153.9 175.9 219.8 240.677.6 88.7 110.8 133.0 155.2 177.4 221.7 266.0 283.2Depth 0600660438240.6511283.2hefdesignfailureload7208.8 Grade Steel StuddingFd,sStudHoleEmbedment depth hefDiameter Diameter(mm)(mm)(mm)(kN)81012.6 14.7 16.8 18.8 19.59319.5101215.7 18.3 20.9 23.6 26.2 28.8 00480540600660720121414345.0161831.4 35.3 39.2 43.1 47.1 51.0 54.9 62.7 78.4 83.721483.7202233.2 37.3 41.5 45.6 49.8 53.9 58.1 66.4 82.9 99.5 116.1 130.7315130.722.0 25.1 28.3 31.4 34.5 37.7 40.8 44.0 45.0242827303035333871.4 76.9 87.9 109.9 131.9 153.9 175.9 219.8 263.8 296.7 329.7 362.7 370.1364077.6 88.7 110.8 133.0 155.2 177.4 221.7 266.0 299.3 332.5 365.8 399.1Depth (mm)43.0 47.3 51.6 55.9 60.2 68.8 86.0 103.2 120.4 137.5 171.9 188.353.2 58.0 62.9 67.7 77.4 96.7 116.1 135.4 154.7 193.4 232.1 244.864.5 69.8 75.2 86.0 107.5 128.9 150.4 171.9 214.9 257.9 290.1 40600660720Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk 86435.7
Design Resistance used with various stud strengths, material and rebar.10.9 Grade Steel StuddingFd,sStudHoleEmbedment depth hefDiameter 6 14.7 16.8 18.8 20.9 23.0 25.1 27.213027.2101215.7 18.3 20.9 23.6 26.2 28.8 31.4 34.0 36.6 41.9 43.116543.1121422.0 25.1 28.3 31.4 34.5 37.7 40.8 44.0 50.3 62.619962.6161831.4 35.3 39.2 43.1 47.1 51.0 54.9 62.7 78.4 94.1 109.8 116.6297116.6202233.2 37.3 41.5 45.6 49.8 53.9 58.1 66.4 82.9 99.5 116.1 132.7 165.9 182.0439182.02428273053.2 58.0 62.9 67.7 77.4 96.7 116.1 135.4 154.7 193.4 232.1 261.1 290.1 319.1 341.0303564.5 69.8 75.2 86.0 107.5 128.9 150.4 171.9 214.9 257.9 290.1 322.4 354.6 386.8776416.7333871.4 76.9 87.9 109.9 131.9 153.9 175.9 219.8 263.8 296.7 329.7 362.7 395.7938515.5364077.6 88.7 110.8 133.0 155.2 177.4 221.7 266.0 299.3 332.5 365.8 2040048054060066072043.0 47.3 51.6 55.9 60.2 68.8 86.0 103.2 120.4 137.5 171.9 206.3 232.1 257.9 262.2Depth 0600660610262.2705341.0720A4-70 Stainless Steel StuddingFd,sStudHoleEmbedment depth hefDiameter Diameter(mm)(mm)6070809081012.6 13.7101215.7 18.3 20.9 72022.0 25.1 28.3 31.6161831.4 35.3 39.2 43.1 47.1 51.0 54.9 58.8202233.2 37.3 41.5 45.6 49.8 53.9 58.1 66.4 82.9 91.7242827303338364043.0 47.3 51.6 55.9 60.2 68.8 86.0 103.2 120.4 2191.7307132.13053.2 58.0 62.9 67.7 77.4 80.2116680.23564.5 69.8 75.2 86.0 98.1118398.11221121.31258142.8Depth (mm)*1280heffailure71.4 76.9 87.9 109.9 12177.6 88.7 110.8 133.0 600660720 Tensile strength 500N/mm2Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
Design Resistance used with various stud strengths, material and rebar.A4-80 Stainless Steel StuddingFd,sStudHoleDiameter DiameterEmbedment depth hef(mm)(mm)81010121214161831.4 35.3 39.2 43.1 47.1 51.0 54.9 62.7 67.2202233.2 37.3 41.5 45.6 49.8 53.9 58.1 66.4 82.9 99.5 0200240280320400480540600660720load(kN)7515.718.3 20.9 23.6 24.89524.822.0 25.1 28.3 31.4 34.5 36.111536.117167.2253104.82307132.153.2 58.0 62.9 67.7 77.4 80.2116680.264.5 69.8 75.2 86.0 98.1118398.11221121.31258142.843.0 47.3 51.6 55.9 60.2 68.8 86.0 103.2 120.4 132.171.4 76.9 87.9 109.9 121.377.6 88.7 110.8 133.0 142.860designfailure(mm)12.6 14.7 15.7Depth 40600660720High bond reinforcing bars Fyk 500N/mm2Fd,sRebarHoleDiameter Diameter(mm)(mm)Embedment depth hef6070809010011012013014016020081011.7 13.7 15.6 17.6 19.6 21.5 23.5 25.2101214.7 17.1 19.6 22.0 24.4 26.9 29.3 31.8 34.2 39.1 39.3121424028032040056064072080019.1 21.8 24.5 27.2 30.0 32.7 35.4 38.1 43.6 54.5 56.6162026.8 30.2 33.5 36.9 40.2 43.6 46.9 53.6 67.0 80.4 93.8 100.6202528.7 32.3 35.9 39.5 43.1 46.7 50.3 57.5 71.9 86.2 100.5 114.9 143.625302835324036444050Depth (mm)50041.1 45.3 49.4 53.5 57.6 65.8 82.3 98.7 115.2 131.7 164.6 205.750.7 55.3 59.9 64.5 73.7 92.2 110.6 129.0 147.5 184.3 230.4 258.168.5 73.7 84.3 105.3 126.4 147.5 168.5 210.7 263.3 294.9 337.179.2 90.5 113.1 135.7 158.4 181.0 226.0 282.8 316.7 362.0 407.295.8 119.7 143.6 167.6 191.5 239.4 299.2 335.1 383.0 430.9 478.860708090*1 Tensile strength 500N/mm2*2 Tensile strength 720800Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk 402.1902510.01050628.3
Design Resistance used with various stud strengths, material and rebar.High bond reinforcing bars Fyk 420N/mm2RebarFd,sHoleDiameter DiameterEmbedment depth 5 13.4 15.4 17.3 19.2 21.1 23.0 25.0 26.9 28.712151620253020024028032040050056064072080010.8 12.3 13.8 15.4 16.9 18.414.7 16.8 18.9 20.9 23.0 25.1 27.2 29.3 33.5 .32021.2 23.9 26.5 29.2 31.8 34.5 37.1 42.5 53.1 73.427773.42522.9 25.8 28.7 31.5 34.4 37.3 40.1 45.8 57.3 68.8 80.2 91.7 050Depth (mm)33.7 37.0 40.4 43.8 47.1 53.9 67.3 80.8 94.3 107.7 134.7 168.339.2 42.7 46.3 49.9 57.0 71.2 85.5 99.7 113.9 142.4 178.0 199.452.9 57.0 65.1 81.4 97.7 113.9 130.2 162.8 203.5 227.9 260.560.3 68.9 86.2 103.4 120.7 137.9 172.4 215.5 241.3 275.8 310.376.6 95.8 114.9 134.1 153.2 191.5 239.4 268.1 306.4 344.7 60640720800Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk865372.5959458.9
CHEMFIX 500 - Pure EpoxyCharacteristic and Design Load resistances based on characteristic bond strengths for hef 4d (minimum embedment) to 20dNon Cracked ConcreteStudCharacteristicResistance (kN)Design Resistance(kN)Cracked ConcreteRecommended Load(kN)CharacteristicResistance (kN)Design Resistance(kN)Recommended 8075.4048.8724.685.1434.91Not ApplicableNot 7.8622.3431.2080Not .49170.0052.54121.43124.64Table notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk340720
CHEMFIX 500 - Pure EpoxyBond Strength FactorsInfluence of concrete strength on combined pull out and concrete cone resistanceConcrete StrengthC15/20N/mm2 (Mpa)fc 1.021.041.061.081.091.10Influence of environmental conditions in non cracked concreteTemp I40 C / 24 CTemp II60 C / 43 CTemp III72 C / 43 CM8M10M12M16M20M24M27M30M33M36Dry ded1.000.940.870.790.710.650.650.600.570.55Dry ded0.650.630.610.590.570.540.500.490.460.44Dry ce of environmental conditions in cracked concreteTemp I40 C / 24 CTemp II60 C / 43 CTemp III72 C / 43 CM8M10M12M16M20M24M27M30M33M36Dry dn/an/a0.500.420.380.380.350.300.270.24Dry dn/an/a0.320.290.280.270.270.250.240.23Dry dn/an/a0.270.270.260.250.240.230.230.22Table notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyCharacteristic and Design Load resistances for REBAR based on characteristic bond strengths for hef 4d (min embedment) to 20dNon Cracked ConcreteCharacteristicResistance (kN)Design Resistance(kN)Cracked ConcreteRecommended Load(kN)CharacteristicResistance (kN)Design Resistance(kN)Recommended ensionShearTensionShearTensionShearØ .5586.393220.70Not Applicable48.25301.592829.95Not Applicable117.6267.862515.7180Not 68.51147.3060.18105.21120.36Table notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk320640
CHEMFIX 500 - Pure EpoxyBond Strength Factors - REBARInfluence of concrete strength on combined pull out and concrete cone resistanceConcrete StrengthN/mm2 (MPa)fc Concrete StrengthN/mm2 (MPa)fc 0/96C90/105---1.101.121.131.141.15---Influence of environmental conditions in non cracked concreteTemp I40 C / 24 CTemp II60 C / 43 CTemp III72 C / 43 CØ8Ø 10Ø 12Ø 16Ø 20Ø 25Ø 28Ø 32Dry and 0.900.850.800.710.650.63Dry and 0.610.590.580.560.550.47Dry and 0.530.500.470.450.430.41Influence of environmental conditions in cracked concreteTemp I40 C / 24 CTemp II60 C / 43 CTemp I72 C / 43 CØ8Ø 10Ø 12Ø 16Ø 20Ø 25Ø 28Ø 32Dry and 0.420.400.380.360.35Dry and 0.270.250.230.220.22Dry and 0.260.240.230.230.22Table notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyMaterial Properties for grades of other threaded rod and rebarStud Grade 8.8Stud Diameter(mm)M8M10M12M16M20M24M27M30M33M36Nrk, sNrd, sStud Grade 10.9Nrk, sNrd, sStud Grade A4-70Nrk, sNrd, sStud Grade A4-80Nrk, sNrd, 8Stud Grade 8.8Stud Grade 10.9Stud Grade A4-70Stud Grade A4-80Stud DiameterVrk, sVrd, sVrk, sVrd, sVrk, sVrd, sVrk, sVrd, 04.2130.9204.2130.9Rebar BSt 500 to DIN 488Rebar Diameter(mm)8101214161820222528323640Nrk, sNrd, sRebar BSt 500 to DIN 488Vrk, sVrd, le notes : see back pageChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyPost installed rebar connectionsMinimum anchorage length1)and lap splice length for C20/25 and maximum installation length ( l max )Rebarlb,min (mm)l0,min (mm)lmax,min 000Ø dsfy,k (N/mm2)8mmN/mm2 MPa1) According to EN 1992-1-1:2004 lb,min (8.6) and l0,min (8.11) for good bond conditions and aδ 1,0with maximum yield stress for rebar B500 B and ƴM 1,15Design values of the ultimate bond resistance f bd 1) in N/mm 2 for all drilling methods for good conditionsConcrete ClassRebar ØØ C50/608mm to 25mm1.622.32.733.43.744.31) Tabulated values for fbd are valid for good bond condition according to EN1992-1-1:2004. For all other bond conditionsmultiply the values for fbd by 0.7.Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyPost installed rebar connectionsValues for pre-calculation of anchoringα1 α2 α3 α4 α5 1.0α2 or α5 0.7; α1 α3 α4 1.0Rebar - Ø dsAnchoragelength lbdDesign valueNrdMortarvolumeAnchoragelength lbdDesign ample C20/25;good bond condition;Rebar Yield Strength500 N/mm2 (500 MPa)81012141620222425* Minimum anchorage length. The design value is valid for "good bond conditions" according to EN 1992-1-1.All other condition: multiply value by 0.7. Mortar volume based on equation: V 1.2 . (d20 - d2d) . . lb / 4Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyPost installed rebar connectionsValues for pre-calculation of overlap jointsα1 α2 α3 α4 α5 1.0Rebar - Ø dsAnchoragelength lbd(mm)81012141620222425α2 or α5 0.7; α1 α3 α4 1.0Design valueNrdMortarvolumeAnchoragelength lbdDesign (mm)(kN)(ml)Example 5291335141184226267311C20/25;good bond condition;Rebar Yield Strength500 N/mm2 (500 MPa)* Minimum anchorage length. The design value is valid for "good bond conditions" according to EN 1992-1-1.All other condition: multiply value by 0.7. Mortar volume based on equation: V 1.2 . (d20 - d2d) . . lb / 4Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyPost installed rebar schematicsChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyEffect of Anchor Spacing - 00Effect of Edge Distance - TensionEdgeDistanceStud / Rebar Diameter8101216202427303336400.640.67 0.630.70 0.65 0.630.73 0.67 0.640.76 0.69 0.66 0.630.79 0.72 0.68 0.640.82 0.74 0.70 0.65 0.630.87 0.79 0.74 0.68 0.65 0.63 0.630.96 0.86 0.80 0.73 0.68 0.65 0.64 0.631.00 0.88 0.82 0.74 0.70 0.66 0.65 0.63 0.63 0.63 0.630.92 0.85 0.76 0.71 0.67 0.66 0.64 0.63 0.63 0.631.00 0.90 0.80 0.74 0.69 0.69 0.66 0.65 0.65 0.650.95 0.84 0.77 0.72 0.71 0.68 0.67 0.67 0.661.00 0.86 0.79 0.73 0.72 0.69 0.68 0.68 0.670.87 0.80 0.74 0.73 0.70 0.69 0.68 0.680.91 0.83 0.76 0.75 0.72 0.71 0.70 0.690.92 0.84 0.77 0.76 0.73 0.71 0.70 0.690.95 0.86 0.79 0.78 0.74 0.73 0.72 0.711.00 0.88 0.81 0.80 0.76 0.74 0.73 0.720.92 0.83 0.82 0.78 0.77 0.75 300330360400Stud / Rebar Diameter8101216202427303336400.640.73 0.630.82 0.70 0.630.90 0.77 0.681.00 0.84 0.74 0.630.91 0.80 0.671.00 0.86 0.71 0.630.92 0.76 0.661.00 0.80 0.70 0.640.89 0.77 0.67 0.63 0.631.00 0.84 0.72 0.70 0.65 0.63 0.670.91 0.78 0.75 0.70 0.66 0.71 0.681.00 0.84 0.81 0.76 0.71 0.74 0.710.89 0.86 0.81 0.75 0.78 0.751.00 0.92 0.86 0.80 0.82 0.781.00 0.94 0.87 0.87 0.831.00 0.94 0.93 0.881.00 0.98 0.931.00 0.981.001.00 0.88 0.87 0.82 0.80 0.78 0.760.92 0.91 0.85 0.83 0.81 0.791.00 0.94 0.88 0.86 0.84 0.811.00 0.93 0.91 0.88 0.841.00 0.96 0.92 0.881.00 0.96 0.911.00 0.951.00Effect of Edge Distance - 0200220240280310330400Stud / Rebar Diameter8101216202427303336400.250.44 0.300.63 0.48 0.300.81 0.65 0.441.00 0.83 0.58 0.401.00 0.72 0.530.86 0.67 0.351.00 0.80 0.441.00 0.58 0.350.72 0.46 0.35 0.300.91 0.62 0.51 0.35 0.32 0.331.00 0.77 0.63 0.46 0.37 0.430.92 0.75 0.57 0.46 0.50 0.321.00 0.88 0.68 0.56 0.56 0.531.00 0.78 0.65 0.63 0.591.00 0.84 0.77 0.721.00 1.00 0.821.00 0.891.00Chemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyMinimum Curing TimeConcreteTemperatureGel - Working TimeMinimum curingtime in dry concreteMinimum curingtime in wetconcrete5 C120 min3000 minx2- Full cure 24 hours15 C60 min1200 minx2- All specifications based on supplied mixer25 C25 min480 minx235 C16 min240 minx240 C10 min150 minx2Temperature RangeConcrete ServiceTemperatureMaximum LongTerm ConcreteTempMaximum ShortTerm ConcreteTempRange I-40 C to 40 C 24 C 40 CRange II-40 C to 60 C 43 C 60 CRange III-40 C to 72 C 43 C 72 CTemperature RangesService temperature range: Range of ambient temperatures after installation and during the lifetime of the anchor.Short term temperature: Temperatures within the service temperature range which vary over short intervals,e.g. day/night cycles and freeze/thaw cycles.Long term temperature: Temperature, within the service temperature range, which will be approximately constantover significant periods of time.Long term temperatures will include constant or near constant temperatures, such as those experienced in cold stores or next to heating installations.Physical PropertiesN/mm2 (MPa)Test Method29.36ASTM D638Compressive Strength120EN 196 Part 1Flexural Strength39EN 196 Part 1Flexural Modulus3706ASTM D790E Modulus3420Tensile Strength1.42 kg/dmDensityShrinkageShore hardnessVOC ContentEN 196 Part 13- 0.4%-87DIN 53 505A RatingChemfix Products Ltd Mill Street East Dewsbury West Yorkshire UKT: 44 (0) 1924 453886 F: 44 (0) 1924 431658 info@chemfix.co.uk www.chemfix.co.uk
CHEMFIX 500 - Pure EpoxyInstallation parameters: drilling hole cleaning and installationDrill hole in the substrate to the required embedment depth using the appropriately sized carbide drill bit. Bore hole cleaning Just before setting ananchor, the bore hole must be free of dust and debris. The manual pump shall be used for blowing out bore holes up to diameters do 24mm andembedment depths up to hef 10d. Blow out at least 4 times from the back of the bore hole, using an extension if needed. Brush 4 times with thespecified brush size (see Table 6) by inserting the steel brush to the back of the hole (if needed with an extension) in a twisting motion and removing it.Blow out again with manual pump at least 4 times.Compressed air cleaning(CAC) for all bore holediameters do and allbore hole depthsBlow 2 times from the back of the hole (if needed with a nozzle extension) over the whole length with oil-free compressed air (min. 6 bar at 6 m³/h).Brush 2 times with the specified brush size (see Table 6) by inserting the steel brush to the back of the hole (if needed with an extension) in a twistingmotion and removing it.X 2 Blow out again with compressed air at least 2 times.Remove the threaded cap from the cartridge. Tightly attach the mixing nozzle. Do not modify the mixer in any way. Made sure the mixing element isinside the mixer. Use only the supplied mixer. Insert the cartridge into the dispenser gun. Discard the initial trigger pulls of adhesive. Discard the first12ml of resin. Please note that after every subsequent mixer change, an initial 12ml of resin should be extruded to waste to continue with even mixing.Inject the adhesive starting at the back of the hole, slowly withdrawing the mixer with each trigger pull. Fill holes approximately 2/3 full, to ensure thatthe annular gap between the anchor and the concrete is completely filled with adhesive along the e
Chemfix 500 is a 2 component high strength pure epoxy chemical anchoring resin system. It is designed for deep embedment and large diameter holes due to its zero shrinkage, and longer working times.
