WIXLIB

Double Conversion SuperheterodyneImproves Inband IMD 30dBm IP3Improved inband IMD5.8 inch ultra-wide viewingangle TFT displayThe IC-7600 employs a double conversionsuperheterodyne system which has animage rejection mixer for the 2nd mixerstage. When compared to a typical tripleconversion system, the double conversionsystem is more difficult to implement but itdramatically reduces signal distortion andprovides a high-linearity RF signal to theDSP processor.Dual DSP for Transmitter/Receiverand Spectrum ScopeTwo separate 32-bit DSP units power thetransmitter/receiver and spectrum scope.These processors give the IC-7600 high performance comparable to our top-of-the-lineIC-7800 andIC-7700, thanks tothe combination ofdual DSP and ouranalog RF designexpertise.Dual DSP104dB Dynamic Range and 30dBm IP3 (3rd order Intercept Point)An astonishing 104dB receiver dynamicrange and 30dBm IP3 in the 14MHz bandwithout sacrificing receiver sensitivity is astandard specification befitting the IC-7600.Even a weak signal adjacent to strong signals is clearly received by the IC-7600.5Three Built-in 1st IF (Roofing)Filters, Including 3kHzThe IC-7600 has three built-in 1st IF (roofing)filters ahead of the 1st IF amplifier stage. The3kHz filter is especially effective in CW andSSB modes, eliminating overloading causedby strong signals just outside the passband.Other Features[Antenna and receiver] 2 TX/RX antennaconnectors and RX antenna connector Automatic antenna tuner Auto notch filterand manual notch filter Digital twin PBT 16-step noise reduction Dual watch[Transmitter] TX monitor function Tone encoder VOX operation All modepower control[CW mode]5.8-inch Ultra-wide Viewing AngleTFT DisplayThe IC-7600’s ultra-wide viewing angle display has excellent color rendering and highcontrast ratio with fast response time. Thesefeatures allow the spectrum scope and simulated analog meters to move smoothly andnaturally.Dual AGC Loops Controlledby DSPThe IC-7600 has dual AGC loops, one analogand one digital, both under DSP control. Thisarchitecture prevents strong adjacent signalsfrom “pumping” the AGC and allows maximum dynamic range in the DSP. CW waveform controlled bythe DSP Multi-function electronic keyer withadjustable keying speed, dot-dash ratio andpaddle polarity APF selection (soft/sharp) Double key jack system[Operation] Spectrum scope USB connectors on the front and rear panel RTTY/PSK31operation with a USB keyboard 2 clocksshow local and UTC time High quality digital voice memory Triple band stacking register Message memory for CW, RTTY andPSK31 operations 101 memory channels Microphone equalizer and adjustable transmitbandwidth FFT scope averaging functionfor PSK and RTTY decode Programmableband edge beep Screen saver function

Base StationTransceiversController Mounted Speaker and JacksThe unique remote head design is perfect forController Rear Panel Viewproviding loud, clearaudio as well asjacks for an externalspeaker/headphones,key and microphone.PHONES/SPMICELEC-KEY MAIN UNIT SpeakerHF, 50/144/440MHz Multi-band,Multi-modeThe IC-7100 fully covers the HF, 50, 144,430/440 MHz amateur bands in multiple modes,providing 100W on HF/50MHz bands, 50W on144MHz band and 35W on 430/440MHz band.D-STAR DV Mode (Digital Voice Data)The IC-7100 provides D-STAR DV mode digitalvoice and low-speed data communication.HF/VHF/UHFHF/UHFFALL MODE TRANSCEIVERIntuitive touch screen interfaceControls at your fingertipswith an angled displayHF, 50/144/440MHzmulti-band, multi-modeIntuitive Touch Screen InterfaceThe innovative touch screen interface providesquick and smooth operation for setting and editing various functions and memories. One Touch SelectionFor example, if you want to change the operating band, tap the frequency on the display. Theband keys will be shown to select the operatingband. Touching themulti-function meterindicator for 1 secondwill quickly changethe transmit meterfunctions. DR (D-STAR Repeater) Function Operation Near Repeater FunctionThe DR function operation makes the D-STARoperation simple and straightforward, even if youare new to D-STAR operation.Straightforward OperationJust tap the mode, filter, function etc., you need to change.The touch screen respondsnaturally changing your settings. With an external, 3rd party GPS*, search theinternal database based on your location.* External GPS receiver or manual data input required.Software KeypadEntering frequency, callsign or editing memorychannels has never been thiseasy. The software keypad onthe touch screen allows youto input alphanumeric characters incredibly quickly.Touch Screen Control PortalOther Features Digital features controlled by the IF DSP DSP controlled AGC function loop SDmemory card slot for saving data Easyvehicle mounting with optional MBF-1 Optional RS-BA1 IP remote controlsoftware Built-in RTTY functions CW fullbreak-in, CW receive reverse, CW auto tuningThe radio control head features a large, multifunction, “touch screen” dot-matrix LCD displaythat is positioned for easy viewing and operation.The controller is compact in size, making it idealfor limited vehicle or desktop space.Resistive Touch ScreenThe 48.6 75.9 mm; 1.91 2.99 in large resistivetouch screen display can be operated whilewearing gloves. Optional multi-function microphone, HM-151 Band scope and SWR graphic display RFspeech compressor controlled by the DSP Voice memory function Multi-function meter 495 regular, 4 call, 6 scan edge and 900 DRmode repeater channels 4 channels TX voicememories 0.5ppm frequency stability Autoreply function* Digital callsign squelch anddigital code squelch* 12.5kHz IF output forDRM (Digital Radio Mondiale) receive* D-STAR DV mode onlyIP REMOTE CONTROL SOFTWARERC-28Optional RS-BA1IP Remote Control SoftwareThe optional RS-BA1 allows you touse the transceiver from anotherroom using your home network, oreven from a remote location overthe Internet. The RS-BA1 has lowvoice latency.USB REMOTEENCODERRC-28RC-28* Base station PC is required for IC-9100, 7600, 7410, 7200 or IC-7100.6

Base StationTransceiversFaster DSP unit and in-house DSP expertiseDouble-conversion superheterodyne 30dBm class third-order intercept point (IP3)Faster DSP Unit andIn-house DSP ExpertiseIcom brings out the best DSP performance,combining more than ten years of DSP technical know-how and much faster DSP processors. Icom’s in-house DSP experts have developed a IC-746PRO series replacement thatevery operator will be proud to own. In additionto the higher speed DSP, the AD/DA converter,AK4620, provides a higher dynamic range andsuperior S/N ratio.Other Features Double-conversion superheterodyne 30dBmclass IP3 (3rd order intercept point) Three first IFfilters (3/6/15kHz) Digital twin PBT AGC loopmanagement with programmable AGC timeconstant Auto/manual notch filter provide morethan 70dB attenuation Noise reduction RFspeech compressor User programmabletone control Built-in voice synthesizer Userprogrammable band edge beep VSC (VoiceSquelch Control) function Two preamplifiertypes: Preamp 1: Improving IMD characteristics, Preamp 2: High gain preamplifier 20dBbuilt-in attenuator Built-in automatic antennatuner CTCSS tone encoder and decoder Tripleband stacking register Quick split and frequencylock functions RIT and Tx variable up to 9.999kHz SSB/CW synchronous tuning 1Hz pitchtuning and display 0.5ppm of high frequencystability Program, memory, select memory,mode select and f scans Automatic tuningstepsIF DSPRugged design for outdoor use100W output powerIF DSPThe latest IF DSP technology is employed in theIC-7200. While the IC-7200 is an entry-classtransceiver, advanced digital features such asflexible filter width and shape setting, digital noisereduction and auto notch filter are comparable tohigher class models.Rugged Design for Outdoor UseThe rugged design of the IC-7200 means yourenjoyment of this rig is not limited only to yourshack. Waterproof protection technologiesused in Icom’s marine radios are applied to thebuttons and knobs on the front panel to providea basic measure of protection against waterintrusion*.* IC-7200 is NOT waterproof.Other Features Digital twin PBT Manual notch filter RIT VOX 0.5ppm frequency stability LCD backlight (Hi/Lo/Off) CI-V interface 201 memorychannels Built-in 20dB attenuator Preamplifier Dial lock Auto tuning step function 1Hz steptuning Band stacking register Built-in voicesynthesizer Quick split Front-facing speaker USB connector for PC control AGC loop management High stability transmitterSimple, straightforward operation with keypadGeneral coverage receive with superior performanceOptional DSP capabilitySimple OperationThe IC-718 is equipped with a minimum number of buttons and controls for simple featureselection. The 10-key pad on the front panelallows direct entry of an operating frequency ora memory channel number. The auto tuningstep function is activated when turning the dial7quickly and helps speed up tuning. The bandstacking register is convenient when changingoperating bands.Other Features Front mounted loud speaker Optional DSPcapability, UT-106 General coverage receiver Built-in electronic keyer Built-in microphonecompressor Combined squelch and RF gaincontrol Preamplifier and attenuator 101memory channels CW full break-in IF shiftinterference rejection 1Hz tuning VOXfunction for hands-free operation Optionalautomatic antenna tuner Digital S/RF meter

All BandTransceivers(With optional UT-121)Superb readability in theVHF/UHF bandReady-to-install1200MHz band unitSatellite mode operationSuperb Readability in theVHF/UHF BandThe IC-9100 provides excellent receiver sensitivity in the VHF/UHF bands, equivalent to thehighly-acclaimed previous VHF/UHF dedicatedmodel, the IC-910H. The IF DSP greatlyimproves intermodulation and noise eliminationand offers better readability than the IC-910H.Ready-to-install1200MHz Band UnitBy installing the optional UX-9100 1200MHzband unit, you can be operational on the1200MHz band immediately. The IC-9100fully covers the HF/50,14 4 , 4 3 0 / 4 4 0 a n d12 0 0 M H z a m a te u rbands in multipleUX-9100, 1200MHz band unitmodes.Satellite Mode OperationThe satellite mode synchronizes the uplink(transmitting) and downlink (receiving) frequencies, and tracks the frequencies in the sametuning step. This function matches both normaland reverse mode satellites. Compensation ofthe Doppler effect can be performed easily. 20satellite memory channels store frequencies,mode and tone settings for quick setup.Double Conversion SuperheterodyneThe best receiver circuit reproduces highfidelity audio without internal distortion. Icomachieves this by adopting a double conversionsuperheterodyne system*. The double conversion system simplifies the electronic circuitryand reduces the number of components whichcause internal distortion. The digital signal processing (DSP) technologies and image rejectionmixer make it possible to adopt this system.* A triple conversion system is used for the 1200MHz band. 30dBm Class IP3Using receiver design techniques introduced inIcom’s highest grade HF transceivers, theIC-9100 has an IP3 of 30dBm* in the HFband. Even a weak signal adjacent to strongsignals is clearly received by the IC-9100.* Typical in 14MHz band. Spacing 100kHzThree First IF Filters (3/6/15kHz)for HF/50MHz BandThe IC-9100 comes with a built-in 15kHz 1st IFfilter and can accept up to two optional filters(3kHz FL-431 and 6kHz FL-430). By changingthe first IF filter widthaccording to the operating mode, the desired isprotected from adjacentinband signals at thelater stages for betterreceiver performance.1st IF filters (6kHz, 3kHz)Other Features Optional D-STAR DV mode Independent dualreceivers 32-bit floating point DSP & 24-bitAD/DA converters AGC loop management Digital IF filter Digital twin PBT and IF shift Noise reduction Noise blanker RF speechcompressor Adjustable transmit bandwidth HF/50MHz, 144MHz 100W, 430/440MHz 75W RTTY demodulator and decoder Ample CWfunctions Built-in antenna tuner for HF/50MHzband Manual notch filter and auto notch filter Large, multi-function LCD USB connectorfor PC control Optional CS-9100 programming software Optional RS-BA1 IP remotecontrol software8

* To use the automatic repeater list function, the position dataof the repeater is required. The ID-5100A will be shipped witha limited number of repeater memories preprogrammed.Dplus Reflector LinkingDplus reflector link commands are added tothe DR function to allow easy reflector operation. Use Reflector, link/unlink to Reflector,echo test and repeater information commandsare selectable.VS-3 Bluetooth HeadsetThe optional Bluetooth headset, VS-3, provides hands-free communication and canremotely control the ID-5100A with three programmable buttons. This provides convenientcommunication in a vehicle.VHF/UHF DUAL BAND DIGITAL TRANSCEIVERIntuitive touch screen operationDV/DV dualwatchor other channel activities while waiting for themain repeater.* Main band audiohas priority if twoDV signals comein at the sameDV/DV dualwatch (DR function) exampletime.Integrated GPS ReceiverIntegrated GPS receiverIntuitive Touch Screen OperationThe intuitive touch screen interface providesquick and smooth operation. The large 5.5inch display (320 128 pixels) responds naturally to the touch – allowing you to changesettings, enterfrequenciesand edit memory channelswith ease.Qwerty keyboard exampleDV/DV DualwatchThe ID-5100A can receive both FM/FM andFM/DV mode signals simultaneously. Two DVmode signals can be monitored for receive oneither channel. You can check other repeatersThe ID-5100A has an integrated GPS receiverin the controller and shows own position,course, speed and altitude on the display. TheGPS position information can be used forexchanging position reports, tracing theGPS log andsearching fornearby repeater sites.Received position information exampleDV/FM Repeater List FunctionThe DV/FM repeater list function assists youin accessing nearby repeaters, even in areasyou are visiting for the first time. The functionsearches for a nearby repeater using therepeater memories with the GPS positioninformation.* Optional UT-133 Bluetooth unit must be installed inthe ID-5100A.Bluetooth application imageVS-3Android deviceOther Features SD card slot for voice and data storage RS-MS1A Android application (free downloadapplication from Google Play ) EnhancedD-PRS functions with object, position, itemsand weather formats Convenient memorycontents management using CSV format Speechfunction announces operating frequency, modeand received callsign (DV mode) Independentmain, volume and SQL knobs for A/B bands AM airband dualwatch CS-5100, cloningsoftware supplied 50W output power onboth VHF and UHF bands Weather channel with weather alert function (USA versiononly) Auto repeater function (USA version only)GPS Position Reporting FunctionsYour position data is shown on the displayand can be sent to other station*1. In addition,the GPS A mode assists in D-PRS modeoperation to send your position information toan APRS server.Other FeaturesD-STAR DV mode capabilityDR (D-STAR repeater) functionfor easy setupCS-80/880 free download software9D-STAR Repeater List andDR Function OperationThe D-STAR repeater list stores up to 300channels of repeater callsigns, frequencies,gateway callsigns, duplex direction and offsetfrequency with channel names of up to 8 characters. The D-STAR repeater (DR) function operation makes it easier to use a D-STAR repeater. CS-80/880 free download software Total of1052 memory channels 16 DTMF memories 50 CTCSS and 104 2 DTCS encoder/decoder*2 Wideband receiver*3 Detachablecontroller Backlit LCD Auto power off andon Power save*1 3rd party GPS receiver is required.*2 FM mode*3 Receiver range differs depending on version.

MobileTransceiversPC Remote Controller SuppliedThe PC controller software is supplied with theID-1. When the ID-1 is connected to a PC, mostfunctions of the ID-1 can be controlled from the PCscreen. The controller software is convenient forediting memory channels, writing short datamessages, checking received call records, etc.128kbps data and 4.8kbpsdigital voice communicationPC remote control softwareWireless Internet access4.8kbps DV (Digital Voice) Modeand 128kbps* DD (Data) ModeThe ID-1 has three modes — analog FM, digital voice and data mode operation. The builtin AMBE vocoder chip provides digitallymodulated, clear audio as well as 128kbpswireless data transmission. In DD mode operation, you can use various Internet applications wirelessly by connecting to a PC withEthernet and USB cables.* Maximum speed.65 Watts of RF output powerwith heavy-duty endurancePowerful 4.5W audio outputprovides loud and clear audioTested to the latestMIL-STD 810 G specificationsStable 65W of Output PowerThe IC-2300H can generate 65W of outputpower. The rugged aluminum die-cast provides effective heat dissipation and keepsRF output even during high duty cycle continuous transmission.Unbeatable 75W output powerwith efficient cooling fanTotal 200 memory channelswith 10 memory banksRemote control microphone,HM-133V75W of Output PowerThe combination of Icom’s one piece,die-cast aluminum chassis and MOS-FETpower amplifier delivers a powerful 75Woutput power. Your communications will getthrough.Other Features Wireless Internet access*1 Digital callsignsquelch (DSQL) and digital code squelch (CSQL) Short data message in DV mode AutomaticFrequency Control (AFC) function for FM and DVmode S-meter squelch Programmed, memoryand select mode scan Break-in communication Enhanced Monitor Request (EMR) function Autorepeater function for FM mode*2 Stand-by beep*1 Within a D-STAR repeater service area.*2 Depending on version.Other Features Tested to the MIL-STD 810 G specifications Total of 207 memory channels Built-inCTCSS and DTCS encoder/decoder Simple operation Multiple scan functions Power supply voltage display Wide/narrow channel setting 4.5W (typical) loudaudio Reduced depth dimensions DTMFautodial Time-out timer Repeater lockout Automatic power off S-meter squelch Selectable LCD backlight color (amber,yellow and green) Weather channelreceive and alert function (USA versiononly) Automatic repeater function (USAversion only) Selectable squelch delayfrom short and long Squelch attenuatorreduces suppression from strong signals PC to transceiver and transceiver to transceiver cloning capabilityDynamic Memory Scan (DMS)With 200 alphanumeric memory channels,Icom’s exclusive DMS system gives youflexibility over your scanning lists neveroffered before in a 2m mobile. Fully customizable into 10 memory banks.Other Features Front mounted speaker 10 DTMF memory channels DTMF pager/code squelchfunction with optional UT-108 50 CTCSSand 104 2 DTCS encoder/decoder Pocket beep and tone scan Squelchattenuator Weather channel with weatheralert* Narrow band FM mode* Coolingfan control Squelch delay Amber andgreen, dual color LCD* USA version only.10

Integrated GPS ReceiverThe ID-51A has a compact58 105.4 26.4 mm body,and weighs only 255g(approx.) with battery packand antenna. In this slimbody, the ID-51A contains5W output power, VHF/UHF dual band, D-STARand integrated GPSreceiver.The integrated GPS receiver provides fast start-uptime and accurate position. Your current positionand altitude are shown on thedisplay and offers a positionreporting function in DVmode. The GPS-A modeassists in easy D-PRS opera- GPS receiver transparent imagetion.95 mm; 3.74 in105.4 mm; 4.15 inLightweight & Compact Body When receiving a call addressed to your callsign,Automatic Reply Function (DV Mode)the ID-51A can automatically reply your currentposition information*. Between ID-51A’s communication, replied position information can pop up onthe caller’s display.V/V, U/U, V/U DualwatchThe dualwatch functionmonitors VHF/VHF, UHF/UHF and VHF/UHF bandssimultaneously.* The audioand squelch levels can beset separately for the mainand sub-bands.TO:CurrentV/U, V/V Dualwatch examplePositi onAuto ReplyplyIndependent AM/FM ReceiverVHF/UHF DIGITAL TRANSCEIVERJL3YRPFM and AM broadcast stations can be listened towhile using the dualwatch function for monitoringham bands. When a ham

Icom's engineering team completely re-engi-neered all of the analog circuitry to match the DSP (Digital Signal Processing) system. Three Hi-spec 1st IF Filters (Roofing Filter)*1 In addition to selectable 6kHz and 15kHz roofing filters, the IC-7800 has a 3kHz roof-ing filter before the 1st IF amplifier. It pro-