WIXLIB

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsPackaging, Tape and Reel InformationDESCRIPTIONDEVICES PER TUBSOptocouplers are available in plastic dual-in-line packages(DIP), SOP packages, and in a surface-mount, gull-wing,lead bend configuration. Optocouplers purchased in theDIP configuration are shipped in tubes. Optocouplerspurchased in a gull-wing configuration can be shipped intubes or on carrier tape. This section provides stickspecifications, tape and reel specifications, and componentinformation.TUBE HV, CNY6440502000HV, CNY6530351050HV, CNY662535875 Figure 1 shows the physical dimensions of transparent,antistatic, plastic shipping tubes. Figure 2 shows tube safetyagency labeling and orientation information.The following table lists the number of parts per tube.Dimensions in millimeters528 0.2330 0.5260 0.5200 0.5150 0.5125 0.5– 1.030 0.5BVISHAY OPTOSEMICONDUCTOR MADE IN MALAYSIA ANTISTATICDetail BDetail AA– 1.0– 1.03 0.5– 1.0380 10.7 0.513 x 10 13012 0.3B6.6 0.3Transparent rigid PVC2.7 0.2R0.16 4.4 0.31.0 14 x0.511 0.3R0.6 0.110 A// 0.2 BDetail ADetail B5.7 0.1517996Section A - BNot to scaleFig. 1 - Shipping Tube Specifications for DIP PackagesRev. 2.2, 06-Oct-11Document Number: 837141For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsDimensions in inches (millimeters)0.46 0.01(11.5 0.25)0.344 0.01(8.6 0.25)Side viewscale: 4X0.104 0.01(2.6 0.25)0.058 0.008(1.46 0.19)0.312 ref.(7.8 ref.)0.03 0.005(0.7 0.13)0.03 0.01(0.7 0.25)Top viewnot to scaleANTISTATICVISHAY OPTOSEMICONDUCTOR4 (100)22.4 0.04(558.8 1)17997Fig. 2 - Shipping Tube Specifications for SOP PackagesTUBE SPECIFICATIONS FOR DIP AND HIGH ISOLATION VOLTAGE PACKAGES1591215915Fig. 3 - DIP-6 N, GRev. 2.2, 06-Oct-11Fig. 4 - DIP-4, -2, -16 N, GDocument Number: 837142For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsTop cover tapeEmbossed carrierEmbossment1799815913Fig. 5 - CNY64Fig. 7 - Tape and Reel Shipping MediumREELS As shown in figure 4, all reels contain standard areas forthe placement of ESD stickers and labels. Each reel alsohas a tape slot in its core. The overall reel dimension is13". Reels contain 1000 6 or 8 pin gullwing parts andcould have up to three inspection lotsESD stickerTape slotin core330(13")15914Fig. 6 - CNY65, 66Regular, specialor bar code labelTAPE AND REEL SPECIFICATIONSSurface-mounted devices are packaged in embossed tapeand wound onto 13" molded plastic reels for shipment, tocomply with Electronics Industries Association StandardEIA-481, revision A, and International ElectrotechnicalCommission standard IEC 60286.17999Fig. 8 - Tape and Reel Shipping MediumLeaders and TrailersThe carrier tape and cover tape are not spliced. Both tapesare one single uninterrupted piece from end to end, asshown in figure 2. Both ends of the tape have empty pocketsmeeting these requirements. Trailer end (inside hub of reel) is 200 mm minimum Leader end (outside of reel) is 400 mm minimum and560 mm maximum Unfilled leader and trailer pockets are sealed Leaders and trailers are taped to tape and hub,respectively, with masking tape All materials are static-dissipativeRev. 2.2, 06-Oct-11Document Number: 837143For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsTAPE AND REEL PACKAGING FOR SINGLE CHANNEL SOIC8 OPTOCOUPLERSDimensions in millimeters (inches)Selected SOIC8 optocouplers are available in tape and reelformat. To order surface mount IL2XXA optocoupler on tapeand reel, add a suffix “T” after the part number, i.e., IL207AT. The tape is 12 mm wide on a 33 cm reel. There are2000 parts per reel. Taped and reeled SOIC8-Aoptocouplers conform to EIA-481-2 and IEC 60286-3.4 0.1(1.57 0.004)Pin 1 andtop of component1.5 (0.059) min.2 0.05 (0.079 0.002)10 pitch cumulativetolerance on tape 0.2 (0.008)0.35 (0.014)Topcovertape1.75 0.1(0.069 0.004)6.4 (0.252)5.5 (0.216) 12.0 0.3(0.472 0.012)3.78 (0.149)5.25(0.205)9.2 (0.36)8.0 0.1(0.315 0.004)0.1 (0.004) max.EmbossmentCenter linesof cavity180031.5 (0.059)Direction of feedFig. 9TAPE AND REEL PACKAGING FOR DUAL CHANNEL(1)SOIC8 OPTOCOUPLERSDimensions in millimeters (inches)Selected dual SOIC8 optocouplers are available in tape andreel format. To order surface mount ILD2XX optocoupler ontape and reel, add a suffix “T” after the part number, i.e.,ILD207T.Note(1) Select dual channel devices are available in the shorter SOIC-8package and will be taped according to the single channeltaping specification The tape is 16 mm and is wound on a 33 cm reel. There are2000 parts per reel. Taped and reeled dual SOIC8optocouplers conform to EIA-481-2 and IEC 60286-3.Pin 1 andtop of component4 0.1(1.57 0.004)2 0.05 (0.079 0.002)1.5 (0.059) min.10 pitch cumulativetolerance on tape 0.2 (0.008)0.3 (0.012) max.Topcovertape1.75 0.1(0.069 0.004)6.6 (0.26)7.5 0.05(0.300 0.002)16.0 0.3(0.630 0.012)3.8 (0.15)6.35 (0.25)13.3 (0.523)8.0 (0.315)0.1 (0.004) max.Center linesof cavityEmbossment180041.5 (0.059)Direction of feedFig. 10Rev. 2.2, 06-Oct-11Document Number: 837144For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsTAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 7Dimensions in millimetersSelected 4 pin optocouplers are available in tape and reelformat. To order a 4 pin optocoupler with option 7 on tapeand reel, add a suffix “T” after the part number,SFH615A-3X007T.The tape is 16 mm and is wound on a 33 cm reel. There are1000 parts per reel. Taped and reeled 4 pin optocouplersconform to EIA-481-2 and IEC 60286-3.10 pitch cumulativetolerance on tape 0.22 0.11.5 0.14 0.10.35 0.051.75 0.17.5 0.116 0.35.05 0.15.05 0.14 XX5 Typ.6.511.5 0.25010.41 0.112 0.14.67 0.13.71 0.1Section X-X21579R 0.76Fig. 11TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 9Dimensions in millimetersSelected 4 pin optocouplers are available in tape and reelformat. To order any SFH6xx6 optocoupler on tape and reel,add suffix “T” after the part number, i.e., SFH6156-3T.Pin 1 andtop of componentThe tape is 16 mm and is wound on a 33 cm reel. There are1000 parts per reel. Taped and reeled 4 pin optocouplersconform to EIA-481-2 and IEC60286-3.4 0.11.5 min.2 0.0510 pitch cumulativetolerance on tape 0.21.75 0.10.3 max.Topcovertape10.27.5 0.054.0716 0.35.0513.3120.1 max.Center linesof cavityEmbossment18005Ø 1.5Direction of feedFig. 12Rev. 2.2, 06-Oct-11Document Number: 837145For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsTAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 9, 90 ROTATIONDimensions in millimeters (inches)Selected 4 pin optocouplers are available in tape and reelformat. To order any SFH6xx series optocoupler on tapeand reel with this orientation, add suffix “T1” after the partnumber, i.e., SFH6156-5T1.16.00 0.30, -0.10(0.013 (0.0008), -0.0004)The tape is 16 mm and is wound on a 33 cm reel. There are2000 parts per reel. Taped and reeled 4 pin optocouplersconform to EIA-481-2 and IEC 60286-3.4 0.1(0.157 0.004)2 0.10(0.079 0.004)1.75 0.11.5 0.10, - 0.00 (0.069 0.004)(0.59 0.004)7.5 0.01(0.295 0.004)10.36 0.100.408 0.00416 0.3(0.630 0.012)10.36 0.100.408 0.0044 8.0 0.10(0.315 0.004)1.5 0.25, - 0.00.059 0.001, - 0.04.92 0.100.194 0.00418401Fig. 13TAPE AND REEL PACKAGING FOR SMD-4 OPTOCOUPLERS WITH OPTION 8Dimensions in millimetersSelected 4 pin optocouplers are available in tape and reelformat. To order any SFH6xx series optocoupler on tapeand reel, add suffix “T” after the part number, i.e.,SFH615A-4X018T. The tape is 24 mm and is wound on a 33 cm reel. There are2000 parts per reel. Taped and reeled 4 pin optocouplersconform to EIA-481-2 and IEC 60286-3.1.5 0.14 0.12 0.11.75 0.10.35 0.0511.5 0.124 0.312.10 0.15X4 8 0.14.9 0.35 (1)X1.5 0.25, - 0.08 21831-1(1)4.1 0.1Section X-X4.65 0.15 in the case of the VO61X seriesR 0.76Fig. 14Rev. 2.2, 06-Oct-11Document Number: 837146For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

Packaging, Tape and Reel Informationwww.vishay.comVishay SemiconductorsTAPE AND REEL PACKAGING FOR SMD-6 OPTOCOUPLERS WITH OPTION 7Dimensions in millimetersSelected 6 pin optocouplers with option 7 are available intape and reel format. To order 6 pin optocoupler with option7 on tape and reel, add a suffix “T” after the option, i.e.,CNY17-3X007T.Pi n 1 and topof component0.35The tape is 16 mm and is wound on a 33 cm reel. There are1000 parts per reel. Taped and reeled 6 pin optocouplersconform to EIA-481-2 and IEC 60286-3.4 0.12 0.051.5 min.10 pitch cumulativetolerance on tape 0.21.75 0.1Topcovertape10.47.5 0.0516 0.34.57913.3120.1 max.EmbossmentCenter linesof cavity18006Ø 1.5Direction of feedFig. 15TAPE AND REEL PACKAGING FOR SMD-6 OPTOCOUPLERS WITH OPTION 9Dimensions in millimetersSelected 6 pin optocouplers with option 9 are available intape and reel format. To order 6 pin optocoupler with option9 on tape and reel, add a suffix “T” after the option, i.e.,CNY17-3X009T.Pin 1 and topof componentThe tape is 16 mm and is wound on a 33 cm reel. There are1000 parts per reel. Taped and reeled 6 pin optocouplersconform to EIA-481-2 and IEC 60286-3.4 0.11.5 min.2 0.0510 pitch cumulativetolerance on tape 0.21.75 0.10.3 max.Topcovertape10.357.5 0.0516 0.34.099.1413.3120.1 max.18007EmbossmentCenter linesof cavityØ 1.5Direction of feedFig. 16Rev. 2.2, 06-Oct-11Document Number: 837147For technical questions, contact: optocoupleranswers@vishay.comTHIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENTARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000