Transcription
Model: AG-PRO-INSQuick Start Guide
Hardware OverviewPOE tLEDPOE INPortTop ViewSteady White Powered and initializing.Steady Blue Working properly andactively connected.Alternating Blue/White Device is busy;do not power off or unplug.
PortsPOE OUT Supports power and data.Connect this port to the airMAX device.POE IN Supports power only. Connectthis port to the PoE adapter or switch.LAN (Optional) Ethernet connection toa host computer.Micro-USB (Optional) Power input froma mobile power pack (min. 20,000mAhrecommended).Reset ButtonsResetResetExtBottom View with Casing Removed
Reset To reset the airGateway tofactory defaults, press and hold theReset button while the airGateway ispowered on. Hold the button until theLED alternates blue and white.Reset Ext To reset the airMAX deviceconnected to the airGateway to factorydefaults, press the Reset Ext button whilethe airMAX device is powered on. Holdthe button for more than 8 seconds untilthe LEDs on the device flash.Configure the airGateway1. Connect an Ethernet cable to the portlabeled POE IN.
2. Connect the other end of the cable toa 24V passive PoE adapter or switch.3. From a mobile device or computer,connect its Wi-Fi to the airGatewayaccess point (SSID) named:airGateway: MAC Address Note: Ensure that DHCP isenabled on your Wi-Fi adapter.4. Launch a web browser and go to:https://192.168.1.1
5. The airOS login screen will appear.Enter ubnt in the Username andPassword fields.Upon initial login you must selectyour Country and Language, andagree to the Terms of Use to use theproduct. Click Login.Note: U.S. product versions arelocked to the U.S. Country Codeto ensure compliance with FCCregulations.
6. Go to the System page and underSystem Accounts, click the key iconto change the default administratorusername and password.Click Change, and then click Apply tosave the changes.Note: The airGateway LED willturn white to indicate that yourchanges are being saved.
7. After your changes have beensaved and the LED is steady blue,disconnect the Ethernet cable fromthe airGateway.The airGateway is now configured andready for use.
Configure an airMAX DeviceUse a mobile device or laptop toconfigure the airMAX device at the pointof installation via the airGateway’s Wi-Fi:1. Power the airGateway by using a24V passive PoE adapter or a mobilebattery pack (min. 20,000mAhrecommended). PoE adapter Connect an Ethernetcable from a 24V passive PoEadapter to the port labeled POE INon the airGateway.
Mobile battery pack Connect amobile power pack to the Micro-USBport on the airGateway.2. Connect an Ethernet cable to the portlabeled POE OUT on the airGateway.
3. Connect the other end of the cable tothe airMAX device.4. Connect the Wi-Fi on your mobiledevice to the airGateway SSID.5. Launch a web browser onyour mobile device and go tohttps://192.168.1.206. The airOS login portal of the airMAXdevice will appear.7. Log in and configure the airMAXdevice as needed.
8. Once you have finished configuringthe airMAX device, remove theairGateway:a. Disconnect the Ethernet cable fromthe device.b. Connect the Ethernet cable fromthe PoE adapter to the device.
Safety Notices1. Read, follow, and keep these instructions.2. Heed all warnings.3. Only use attachments/accessories specified by themanufacturer.WARNING: Do not use this product in locationthat can be submerged by water.WARNING: Avoid using this product during anelectrical storm. There may be a remote riskof electric shock from lightning.Electrical Safety Information1. Compliance is required with respect to voltage,frequency, and current requirements indicated onthe manufacturer’s label. Connection to a differentpower source than those specified may result inimproper operation, damage to the equipment orpose a fire hazard if the limitations are not followed.2. There are no operator serviceable parts inside thisequipment. Service should be provided only by aqualified service technician.3. Contact a qualified electrician or the manufacturerif there are questions about the installation prior toconnecting the equipment.4. Protective earthing is provided by Listed AC adapter.Building installation shall provide appropriate shortcircuit backup protection.5. Protective bonding must be installed in accordancewith local national wiring rules and regulations.
Limited WarrantyUBIQUITI NETWORKS, Inc (“UBIQUITI NETWORKS”)warrants that the product(s) furnished hereunder (the“Product(s)”) shall be free from defects in material andworkmanship for a period of one (1) year from the dateof shipment by UBIQUITI NETWORKS under normal useand operation. UBIQUITI NETWORKS’ sole and exclusiveobligation and liability under the foregoing warrantyshall be for UBIQUITI NETWORKS, at its discretion, torepair or replace any Product that fails to conform to theabove warranty during the above warranty period. Theexpense of removal and reinstallation of any Productis not included in this warranty. The warranty periodof any repaired or replaced Product shall not extendbeyond its original term.Warranty ConditionsThe above warranty does not apply if the Product:(I)has been modified and/or altered, or anaddition made thereto, except by UbiquitiNetworks, or Ubiquiti Networks’ authorizedrepresentatives, or as approved by UbiquitiNetworks in writing;(II)has been painted, rebranded or physicallymodified in any way;(III)has been damaged due to errors or defectsin cabling;*640-00185-05*640-00185-05
(IV)has been subjected to misuse, abuse,negligence, abnormal physical,electromagnetic or electrical stress, includinglightning strikes, or accident;(V)has been damaged or impaired as a result ofusing third party firmware;(VI)has no original Ubiquiti MAC label, or ismissing any other original Ubiquiti label(s); or(VII)has not been received by Ubiquiti within 30days of issuance of the RMA.In addition, the above warranty shall apply only if: theproduct has been properly installed and used at alltimes in accordance, and in all material respects, withthe applicable Product documentation; all Ethernetcabling runs use CAT5 (or above), and for outdoorinstallations, shielded Ethernet cabling is used, andfor indoor installations, indoor cabling requirementsare followed.ReturnsNo Products will be accepted for replacement or repairwithout obtaining a Return Materials Authorization(RMA) number from UBIQUITI NETWORKS during thewarranty period, and the Products being receivedat UBIQUITI NETWORKS’ facility freight prepaidin accordance with the RMA process of UBIQUITINETWORKS. Products returned without an RMA numberwill not be processed and will be returned freightcollect or subject to disposal. Information on the RMAprocess and obtaining an RMA number can be found at:www.ubnt.com/support/warranty.
DisclaimerEXCEPT FOR ANY EXPRESS WARRANTIES PROVIDEDHEREIN, UBIQUITI NETWORKS, ITS AFFILIATES,AND ITS AND THEIR THIRD PARTY DATA, SERVICE,SOFTWARE AND HARDWARE PROVIDERS HEREBYDISCLAIM AND MAKE NO OTHER REPRESENTATIONOR WARRANTY OF ANY KIND, EXPRESS, IMPLIEDOR STATUTORY, INCLUDING, BUT NOT LIMITED TO,REPRESENTATIONS, GUARANTEES, OR WARRANTIES OFMERCHANTABILITY, ACCURACY, QUALITY OF SERVICEOR RESULTS, AVAILABILITY, SATISFACTORY QUALITY,LACK OF VIRUSES, QUIET ENJOYMENT, FITNESS FOR APARTICULAR PURPOSE AND NON-INFRINGEMENT ANDANY WARRANTIES ARISING FROM ANY COURSE OFDEALING, USAGE OR TRADE PRACTICE IN CONNECTIONWITH SUCH PRODUCTS AND SERVICES. BUYERACKNOWLEDGES THAT NEITHER UBIQUITI NETWORKSNOR ITS THIRD PARTY PROVIDERS CONTROL BUYER’SEQUIPMENT OR THE TRANSFER OF DATA OVERCOMMUNICATIONS FACILITIES, INCLUDING THEINTERNET, AND THAT THE PRODUCTS AND SERVICESMAY BE SUBJECT TO LIMITATIONS, INTERRUPTIONS,DELAYS, CANCELLATIONS AND OTHER PROBLEMSINHERENT IN THE USE OF COMMUNICATIONSFACILITIES. UBIQUITI NETWORKS, ITS AFFILIATES ANDITS AND THEIR THIRD PARTY PROVIDERS ARE NOTRESPONSIBLE FOR ANY INTERRUPTIONS, DELAYS,CANCELLATIONS, DELIVERY FAILURES, DATA LOSS,CONTENT CORRUPTION, PACKET LOSS, OR OTHERDAMAGE RESULTING FROM ANY OF THE FOREGOING.In addition, UBIQUITI NETWORKS does not warrantthat the operation of the Products will be error-free orthat operation will be uninterrupted. In no event shallUBIQUITI NETWORKS be responsible for damages or
claims of any nature or description relating to systemperformance, including coverage, buyer’s selectionof products (including the Products) for buyer’sapplication and/or failure of products (includingthe Products) to meet government or regulatoryrequirements.Limitation of LiabilityEXCEPT TO THE EXTENT PROHIBITED BY LOCAL LAW,IN NO EVENT WILL UBIQUITI OR ITS SUBSIDIARIES,AFFILIATES OR SUPPLIERS BE LIABLE FOR DIRECT,SPECIAL, INCIDENTAL, CONSEQUENTIAL OR OTHERDAMAGES (INCLUDING LOST PROFIT, LOST DATA,OR DOWNTIME COSTS), ARISING OUT OF THE USE,INABILITY TO USE, OR THE RESULTS OF USE OF THEPRODUCT, WHETHER BASED IN WARRANTY, CONTRACT,TORT OR OTHER LEGAL THEORY, AND WHETHER ORNOT ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.NoteSome countries, states and provinces do not allowexclusions of implied warranties or conditions, so theabove exclusion may not apply to you. You may haveother rights that vary from country to country, state tostate, or province to province. Some countries, statesand provinces do not allow the exclusion or limitationof liability for incidental or consequential damages,so the above limitation may not apply to you. EXCEPTTO THE EXTENT ALLOWED BY LOCAL LAW, THESEWARRANTY TERMS DO NOT EXCLUDE, RESTRICT ORMODIFY, AND ARE IN ADDITION TO, THE MANDATORYSTATUTORY RIGHTS APPLICABLE TO THE LICENSE OFANY SOFTWARE (EMBEDDED IN THE PRODUCT) TOYOU. The United Nations Convention on Contracts for
the International Sale of Goods shall not apply to anytransactions regarding the sale of the Products.ComplianceFCCChanges or modifications not expressly approved bythe party responsible for compliance could void theuser’s authority to operate the equipment.This device complies with Part 15 of the FCC Rules.Operation is subject to the following two conditions.1. This device may not cause harmful interference, and2. This device must accept any interference received,including interference that may cause undesiredoperation.This equipment has been tested and found to complywith the limits for a Class B digital device, pursuantto Part 15 of the FCC Rules. These limits are designedto provide reasonable protection against harmfulinterference in a residential installation. This equipmentgenerates, uses and can radiate radio frequency energyand, if not installed and used in accordance with theinstructions, may cause harmful interference to radiocommunications. However, there is no guarantee thatinterference will not occur in a particular installation.If this equipment does cause harmful interference toradio or television reception, which can be determinedby turning the equipment off and on, the user isencouraged to try to correct the interference by one ormore of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipmentand receiver.
Connect the equipment into an outlet on acircuit different from that to which the receiver isconnected. Consult the dealer or an experienced radio/TVtechnician for help.Operations of this equipment in a residential area islikely to cause harmful interference in which case theuser will be required to correct the interference at hisown expense.This radio transmitter FCC ID: SWX-AMGPRO has beenapproved by FCC to operate with the antenna typeslisted below with the maximum permissible gain andrequired antenna impedance for each antenna typeindicated. Antenna types not included in this list, havinga gain greater than the maximum gain indicated forthat type, are strictly prohibited for use with this device.Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi5 GHz PIFA antenna, Gain: 2 dBiIndustry CanadaCAN ICES-3(B)/NMB-3(B)To reduce potential radio interference to other users,the antenna type and its gain should be so chosenthat the equivalent isotropically radiated power(e.i.r.p.) is not more than that permitted for successfulcommunication.This device complies with Industry Canada licenceexempt RSS standard(s). Operation is subject to thefollowing two conditions:
1. This device may not cause interference, and2. This device must accept any interference, includinginterference that may cause undesired operationof the device.Users should also be advised that high-power radarsare allocated as primary users (i.e. priority users) ofthe band 5650-5850 MHz and that these radars couldcause interference and/or damage to LE-LAN devices.This radio transmitter (IC: 6545A-AMGPRO) hasbeen approved by Industry Canada to operate withthe antenna types listed below with the maximumpermissible gain and required antenna impedancefor each antenna type indicated. Antenna types notincluded in this list, having a gain greater than themaximum gain indicated for that type, are strictlyprohibited for use with this device.Antenna Information: 2.4 GHz PIFA antenna, Gain: 1 dBi5 GHz PIFA antenna, Gain: 2 dBiCAN ICES-3(B)/NMB-3(B)Pour réduire le risque d’interférence aux autresutilisateurs, le type d’antenne et son gain doivent êtrechoisies de façon que la puissance isotrope rayonnéeéquivalente (PIRE) ne dépasse pas ce qui est nécessairepour une communication réussie.Cet appareil est conforme à la norme RSS Industrie Canadaexempts de licence norme(s). Son fonctionnement estsoumis aux deux conditions suivantes:1. Cet appareil ne peut pas provoquer d’interférences et2. Cet appareil doit accepter toute interférence, ycompris les interférences qui peuvent causer unmauvais fonctionnement du dispositif.
Les utilisateurs devraient également noter que radarshaute puissants sont alloués comme principauxutilisateurs (c’est-à-dire les utilisateurs de priorité) desbandes et 5650 à 5850 MHz et que ces radars pourraientcauser des interférences ou dommages aux dispositifsLAN. Cet émetteur radio (IC: 6545A-AMGPRO) a étéapprouvée par Industrie Canada pour l’exploitationavec l’antenne types énumérés ci-dessous avec le gainmaximal admissible et requis l’impédance de l’antennepour chaque type d’antenne indiqué. Types d’antennenon inclus dans cette liste, ayant un gain supérieur augain maximal indiqué pour ce type, sont strictementinterdits pour une utilisation avec cet appareil.Informations d’antenne: 2.4 GHz PIFA antenne, Gain: 1 dBi5 GHz PIFA antenne, Gain: 2 dBiRF Exposure WarningThe antennas used for this transmitter must be installedto provide a separation distance of at least 20 cm fromall persons and must not be located or operating inconjunction with any other antenna or transmitter.Les antennes utilisées pour ce transmetteur doiventêtre installé en considérant une distance de séparationde toute personnes d’au moins 20 cm et ne doivent pasêtre localisé ou utilisé en conflit avec tout autre antenneou transmetteur.Australia and New ZealandWarning: This is a Class B product. In a domesticenvironment this product may cause radiointerference in which case the user may berequired to take adequate measures.
CE MarkingCE marking on this product represents theproduct is in compliance with all directivesthat are applicable to it.RoHS/WEEE Compliance StatementEnglishEuropean Directive 2002/96/EC requires that theequipment bearing this symbol on the productand/or its packaging must not be disposed of withunsorted municipal waste. The symbol indicatesthat this product should be disposed of separatelyfrom regular household waste streams. It is yourresponsibility to dispose of this and other electric andelectronic equipment via designated collection facilitiesappointed by the government or local authorities.Correct disposal and recycling will help preventpotential negative consequences to the environmentand human health. For more detailed information aboutthe disposal of your old equipment, please contact yourlocal authorities, waste disposal service, or the shopwhere you purchased the product.DeutschDie Europäische Richtlinie 2002/96/EC verlangt, dasstechnische Ausrüstung, die direkt am Gerät und/oder ander Verpackung mit diesem Symbol versehen ist, nichtzusammen mit unsortiertem Gemeindeabfall entsorgt
werden darf. Das Symbol weist darauf hin, dass dasProdukt von regulärem Haushaltmüll getrennt entsorgtwerden sollte. Es liegt in Ihrer Verantwortung, diesesGerät und andere elektrische und elektronische Geräteüber die dafür zuständigen und von der Regierung oderörtlichen Behörden dazu bestimmten Sammelstellenzu entsorgen. Ordnungsgemäßes Entsorgen undRecyceln trägt dazu bei, potentielle negative Folgenfür Umwelt und die menschliche Gesundheit zuvermeiden. Wenn Sie weitere Informationen zurEntsorgung Ihrer Altgeräte benötigen, wenden Siesich bitte an die örtlichen Behörden oder städtischenEntsorgungsdienste oder an den Händler, bei dem Siedas Produkt erworben haben.EspañolLa Directiva 2002/96/CE de la UE exige que los equiposque lleven este símbolo en el propio aparato y/o en suembalaje no deben eliminarse junto con otros residuosurbanos no seleccionados. El símbolo indica que elproducto en cuestión debe separarse de los residuosdomésticos convencionales con vistas a su eliminación.Es responsabilidad suya desechar este y cualesquieraotros aparatos eléctricos y electrónicos a través delos puntos de recogida que ponen a su disposición elgobierno y las autoridades locales. Al desechar y reciclarcorrectamente estos aparatos estará contribuyendo aevitar posibles consecuencias negativas para el medioambiente y la salud de las personas. Si desea obtenerinformación más detallada sobre la eliminación segurade su aparato usado, consulte a las autoridades locales,al servicio de recogida y eliminación de residuos desu zona o pregunte en la tienda donde adquirió elproducto.
FrançaisLa directive européenne 2002/96/CE exige quel’équipement sur lequel est apposé ce symbole sur leproduit et/ou son emballage ne soit pas jeté avec lesautres ordures ménagères. Ce symbole indique quele produit doit être éliminé dans un circuit distinctde celui pour les déchets des ménages. Il est de votreresponsabilité de jeter ce matériel ainsi que tout autrematériel électrique ou électronique par les moyens decollecte indiqués par le gouvernement et les pouvoirspublics des collectivités territoriales. L’élimination etle recyclage en bonne et due forme ont pour but delutter contre l’impact néfaste potentiel de ce type deproduits sur l’environnement et la santé publique. Pourplus d’informations sur le mode d’élimination de votreancien équipement, veuillez prendre contact avec lespouvoirs publics locaux, le service de traitement desdéchets, ou l’endroit où vous avez acheté le produit.ItalianoLa direttiva europea 2002/96/EC richiede che leapparecchiature contrassegnate con questo simbolosul prodotto e/o sull’imballaggio non siano smaltiteinsieme ai rifiuti urbani non differenziati. Il simboloindica che questo prodotto non deve essere smaltitoinsieme ai normali rifiuti domestici. È responsabilitàdel proprietario smaltire sia questi prodotti sia le altreapparecchiature elettriche ed elettroniche mediantele specifiche strutture di raccolta indicate dal governoo dagli enti pubblici locali. Il corretto smaltimentoed il riciclaggio aiuteranno a prevenire conseguenzepotenzialmente negative per l’ambiente e per lasalute dell’essere umano. Per ricevere informazioni
più dettagliate circa lo smaltimento delle vecchieapparecchiature in Vostro possesso, Vi invitiamo acontattare gli enti pubblici di competenza, il serviziodi smaltimento rifiuti o il negozio nel quale aveteacquistato il prodotto.Declaration of ConformityČesky[Czech]UBIQUITI NETWORKS tímto prohlašuje, že totoUBIQUITI NETWORKS zařízení, je ve shod sezákladními požadavky a dalšími příslušnýmiustanoveními směrnice 1999/5/ES.Dansk[Danish]Hermed, UBIQUITI NETWORKS, erklærer at denneUBIQUITI NETWORKS enhed, er i overensstemmelsemed de væsentlige krav og øvrige relevante krav idirektiv 1999/5/EF.Nederlands[Dutch]Hierbij verklaart UBIQUITI NETWORKS, dat dezeUBIQUITI NETWORKS apparaat, in overeenstemmingis met de essentiële eisen en de andere relevantebepalingen van richtlijn 1999/5/EC.EnglishHereby, UBIQUITI NETWORKS, declares that thisUBIQUITI NETWORKS device, is in compliance withthe essential requirements and other relevantprovisions of Directive 1999/5/EC.Eesti[Estonian]Käesolevaga UBIQUITI NETWORKS kinnitab, et antudUBIQUITI NETWORKS seade, on vastavus olulistelenõuetele ja teistele asjakohastele sätetele direktiivi1999/5/EÜ.Suomi[Finnish]Täten UBIQUITI NETWORKS vakuuttaa, että tämäUBIQUITI NETWORKS laite, on yhdenmukainenolennaisten vaatimusten ja muiden sitä koskeviendirektiivin 1999/5/EY.
Français[French]Par la présente UBIQUITI NETWORKS déclare quel’appareil UBIQUITI NETWORKS, est conforme auxexigences essentielles et aux autres dispositionspertinentes de la directive 1999/5/CE.Deutsch[German]Hiermit erklärt UBIQUITI NETWORKS, dass sich diesesUBIQUITI NETWORKS Gerät, in Übereinstimmungmit den grundlegenden Anforderungen und denanderen relevanten Vorschriften der Richtlinie1999/5/EG befindet.Ελληνική[Greek]Δια του παρόντος, UBIQUITI NETWORKS, δηλώνειότι αυτή η συσκευή UBIQUITI NETWORKS, είναι σεσυμμόρφωση με τις βασικές απαιτήσεις και τις λοιπέςσχετικές διατάξεις της οδηγίας 1995/5/ΕΚ.Magyar[Hungarian]Ezennel UBIQUITI NETWORKS kijelenti, hogy ez aUBIQUITI NETWORKS készülék megfelel az alapvetőkövetelményeknek és más vonatkozó 1999/5/EKirányelv rendelkezéseit.Íslenska[Icelandic]Hér, UBIQUITI NETWORKS, því yfir að þetta UBIQUITINETWORKS tæki er í samræmi við grunnkröfur ogönnur viðeigandi ákvæði tilskipun 1999/5/EC.Italiano[Italian]Con la presente, UBIQUITI NETWORKS, dichiara chequesto dispositivo UBIQUITI NETWORKS, è conformeai requisiti essenziali ed alle altre disposizionipertinenti della direttiva 1999/5/CE.Latviski[Latvian]Ar šo, UBIQUITI NETWORKS, deklarē, ka UBIQUITINETWORKS ierīce, ir saskaņā ar būtiskajām prasībāmun citiem attiecīgiem noteikumiem Direktīvā1999/5/EK.LietuviškaiUBIQUITI NETWORKS deklaruoja, kad šis UBIQUITI[Lithuanian] NETWORKS įrenginys atitinka esminius reikalavimusir kitas 1999/5/EB Direktyvos nuostatas.
Malti[Maltese]Hawnhekk, UBIQUITI NETWORKS, tiddikjara li danil-mezz UBIQUITI NETWORKS huwa konformi marrekwiżiti essenzjali u dispożizzjonijiet rilevanti oħrajnta ‘Direttiva 1999/5/EC.NorskHerved UBIQUITI NETWORKS, erklærer at denne[Norwegian] UBIQUITI NETWORKS enheten, er i samsvar medde grunnleggende kravene og andre relevantebestemmelser i direktiv 1999/5/EF.Slovensky[Slovak]Týmto UBIQUITI NETWORKS, prehlasuje, že totoUBIQUITI NETWORKS zariadenie, je v súlade sozákladnými požiadavkami a ďalšími relevantnýmiustanoveniami smernice 1999/5/ES.Svenska[Swedish]Härmed UBIQUITI NETWORKS, intygar att dennaUBIQUITI NETWORKS enhet är i överensstämmelsemed de väsentliga egenskapskrav och övrigarelevanta bestämmelser som framgår av direktiv1999/5/EG.Español[Spanish]Por medio de la presente UBIQUITI NETWORKSdeclara que este dispositivo UBIQUITI NETWORKS,cumple con los requisitos esenciales y cualesquieraotras disposiciones aplicables o exigibles de laDirectiva 1999/5/CE.Polski[Polish]Niniejszym, Ubiquiti Networks, oświadcza, że urządzenie UBIQUITI NETWORKS, jest zgodny zzasadniczymi wymaganiami oraz pozostałymistosownymi postanowieniami Dyrektywy 1999/5/EC.PortuguêsUBIQUITI NETWORKS declara que este dispositivo[Portuguese] UBIQUITI NETWORKS, está conforme com osrequisitos essenciais e outras disposições daDirectiva 1999/5/CE.Română[Romanian]Prin prezenta, UBIQUITI NETWORKS declară că acestdispozitiv UBIQUITI NETWORKS este în conformitatecu cerințele esențiale și alte prevederi relevante aleDirectivei 1999/5/CE.
Online ResourcesSupport support.ubnt.comCommunity community.ubnt.comDownloads downloads.ubnt.comwww.ubnt.com 2015-2016 Ubiquiti Networks, Inc. All rightsreserved. Ubiquiti, Ubiquiti Networks, the Ubiquiti Ulogo, the Ubiquiti beam logo, airMAX, airOS, andairGateway are trademarks or registered trademarks ofUbiquiti Networks, Inc. in the United States and in othercountries. All other trademarks are the property of theirrespective owners.PH081816
beyond its original term. Warranty Conditions The above warranty does not apply if the Product: (I) has been modified and/or altered, or an addition made thereto, except by Ubiquiti Networks, or Ubiquiti Networks' authorized representatives, or as approved by Ubiquiti Networks in writing; (II) has been painted, rebranded or physically
