Transcription
Page - 1DOOR CLOSERS712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:35
Page - 2DOOR CLOSERPhiladelphia Hardware Group Inc. is presenting the finest ADVANTAGE surfacemounting door closers certified by BHMA including: Multi-size door closer: 9000, 8000, 6000, 6000S (slim cover), 4400 series. Standard size door closer: 4000, 3000, 2000 series. Multi-size Delay Action door closer: 8000/DA, 6000/DA, 6000S/DA series.GENERAL INFORMATIONANSI A156.4 – American National Standard for Door Controls-ClosersADVANTAGE Grade 1 Door Closers are certified by ANSI/BHMA A156.4.ADVANTAGE Grade 2 Door Closers are factory tested to meet or exceed ANSI Grade 2 required strength and performance.UL ListedAll of ADVANTAGE door closer series are UL listed, and conforms to Standards UL10C and UPC 7-2(1997).Meet ADA RequirementsADVANTAGE door closer 9000, 8000, 6000, and 4400 series meet requirements of ANSI A117.1, ADA.Standards for Accessible Design, and NFPA 101.Please note Door Closer with reduced opening force may not provide sufficient power to close a door.Note: The information below concerning the Americans With Disabilities Act (A.D.A.) has been generated from ANSI/BHMA A117.1,the Federal Register, Part III, published by the Department of Justice, office of the Attorney General, 28CFR, part 36, and NFPA101. The information listed here are requirements which must be met for door opening accessibility by the handicapped or disabled.Please refer to ANSI/BHMA A117.1, ADA standards and NFPA 101 for specific details. Door Opening WidthSingle-leaf Doorways shall have a clear opening of 32” minimum. Clear opening of doorways with swinging doors shall bemeasured from the face of door and stop with the door open 90 .Double-leaf Doorways should have at least one active leaf to meet the minimum opening criteria. Door Opening FaceDoor closers shall be adjusted so that from the open position of 90 the time required to move the door to an open positionof 12 shall be 5 seconds minimum.The maximum force for pushing open or pulling open doors other than fire doors shall be as follows:1. Interior hinged door: 5 lbs.2. Exterior hinged door: 8.5 lbs.* 4400 series apply to interior hinged door only. Fire Door (NFPA-101)The force required to operate the door assembly in the direction of door leaf travel is not more than 30 lbf (133 N) to set the doorleaf in motion and is not more than 15 lbf (67 N) to close the door assembly or open it to the minimum required width.Note: These forces shall be applied at the latch stile. The pound forces stated above should be reduced where possible to complywith exterior hinged door and interior hinged door requirements. However, door closing capability must not be compromised. Door Closing SpeedADA: The closing speed from an open position 70 to a point 3” from the latch will take at least 3 seconds.A117.1: Door closers shall be adjusted so that from the open position of 90 the time required to move the door to an openposition of 12 shall be 5 seconds minimum.Door Closers Handing are non-handed and suitable for left-opening or right-opening door.All Weather Hydraulic Fluid used to ensure smooth operation under severe weather conditions, operation temperatures130 F -40 F (55 C -40 C).Finish Stock available Aluminum (BHMA 689) for all model,Gold (BHMA 696) for all modelAluminumDuranodic (BHMA 695) for all modelSatin Chrome (BHMA 652) for 8000 seriesDuro (Duranodic)GoldACCESSORIESDrop Plate allows a door closer to be fitted on narrow top rail or narrow top frame door.Most of the ADVANTAGE door closers have different kinds of Drop Plates for installation requirements, see following pages in detail.Hold Open Arm used when door is requiring for a clear opening doorways at 90 stop.* Should not be used on Fire door application.Parallel Rigid Cush Arm is a heavy duty arm with an auxiliary stop in soffit shoe to stop the door opening at a specificpoint. Apply to door where wall or floor stops are not appropriate. Parallel arm mounting application only.Parallel Rigid Spring Cush Arm is Parallel Rigid Cush Arm with a Spring Stop in soffit shoe for abusive application.1712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:36
Page - 3DOOR CLOSERACCESSORIESParallel Rigid Hold Open Cush Arm is a heavy duty hold open arm featured with a plunger hold open to engage ordisengage hold open by a handle on the arm. Auxiliary stop in soffit shoe to stop the door opening at a specific point.Parallel arm mounting application only.* Should not be used on Fire door application.Parallel Rigid Hold Open Spring Cush Arm is Parallel Rigid Hold Open Cush Arm with a Spring Stop in soffit shoefor abusive application.* Should not be used on Fire door application.Parallel Rigid Arm is an extra heavy duty arm that is intended to use in heavy traffic areas. Parallel arm mounting application only.Slide Track Arm with Hold Open Stop provides the smoothest lines available in a surface- mounted door closer. The designminimize projection and eliminate obtrusive arm angles. The arm geometry reduces door closer power efficiency by approximately 25%from that of a regular arm. * Using hold open stop is not code compliant on fire rated doors.Blade Stop Spacer lowers parallel arm shoe to clear 1/2” (13mm) blade stop.Arm Support BracketArm Support Bracket provides anchor for fifth screw, to use with stop armswhen reveal is less than 3-1/16” (78mm). (for 8000 door closer only)Blade Stop SpacerDOOR CLOSER APPLICATIONThere are three basic methods of mounting surface door closers to the door and frame including regular arm, parallel arm and topjamb mounts. All ADVANTAGE door closers are supplied standard with a tri-pack for mounting any of three types applications.Parallel Arm InstallationRegular ArmInstallationcloser mountson hinge(pull) side of doorLeft hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRRegular Arm (Pull side)Most power-efficient applicationThe Closer body is mounted on thehinge side of the door top rail.The forearm is mounted to the frameface by a mounting shoe.Arm projects at approximately a 90 angle away from the door.Top JambInstallationcloser mountson frame face onopposite to hinge(pull) side of doorcloser mounts onopposite to hinge (pull) side of doorLeft hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRTop Jamb (Push side)More power-efficient than theparallel arm applicationApplying to a closer with narrow toprail on a door.The closer body is mounted to theframe face above the door, oppositethe door hinge side.The forearm is then mounted to thetop rail of the door.Left hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRUse adjustable wrench to rotate spindle 45 counter-clockwise for right hand door or clockwisefor left hand door. Place main arm on spindle sothat the “R” (Right hand door) or “L” (Left hand door)lines up with the spindle flat. Secure main arm andspindle by tightening spindle bolt.Parallel Arm (Push side)Least power-efficient applicationThe closer body is mounted on the toprail of the door, opposite the hinge sideof the door.The forearm is mounted by a parallel armbracket to the underside of the frame.The arm is parallel to the door, whichmakes it less likely to be damaged.* Top reveal should have enough spacefor using this application.CLOSER ADJUSTMENTADVANTAGE Door closers have hex wrench controlling valves for adjusting Closing speed and latch speed. Multi-size door closers have a nut for spring poweradjustment, and additional valve for Backcheck. Delay Action control valve availablewith Delay Action model.Opening Cycle2712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:37
Page - 4DOOR CLOSERClosing speed &Latching speed aredual valve control for doorclosing speed.Closing speed is the speed ofdoor closing from full openingto approximately 10 5 of doorclosed position.Latching speed is the speedfrom approximately 10 5 dooropening to door closed position. Slow latch speed providesless door closing noise.Backcheck slows down thedoor opening at approximately70 in order to prevent damageto building and door frames.The backcheck control valveprovides a 20 adjustment (70 90 ) to set the optimum backcheck start point.* Multi-size door closers arestandard with Backcheckfunction.Delay Action is the 3rdcontrol for closing speed adjustment.It effective from full openingto approximately 70 , andprovides a slow closing speed.The closing time between 180 to 70 is at least 20seconds,and easily adjustable up to1minutes. Closer with DelayAction provides sufficienttime that allows people or theelderly to get through the doorbefore it starts to close.Multi-size Spring adjustmentMulti-size door closers are able to adjust the spring power to meet the power needs of the door.Spring power of the closer can be increased by turning the power adjustment nut clockwise, vice versa.Closer Size (Spring Power)CloserRecom m e n d e d Ma x i m u m Do o r S i z eRegular & Top JambParallel ArmDoor WeightSizeInteriorExterior Swing-in(Pull Side)Exterior Swing-out(Push SideInterior Swing-out(Push side)Exterior Swing-out(Push side)128”N/AN/AN/AN/A236”N/AN/A30”N/A66 99342”30”36”36”30”99 143448”36”42”42”36”143 187554”42”48”48”42”187 264660”48”54”54”48”264 330(Lbs.)33 66* Multi-size door closers provide the spring power required to fit your door size and application.3712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:37
Page - 59000 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel90009000/DAULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckAdjustable power size 1-6 with Back Check and Delay ActionApplications Heavy Duty Commercial model ideal for high traffic doorsuch as schools, hospitals, and public institutions Same mounting hole pattern as CAL-ROYAL 900(CTC 11-1/8” x 1-1/8”), ideal for renovations Tri-packed for all type applications Sex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 1-6Factory preset size 3 Meet ADA Standard with adjustable BackcheckProduct SpecificationMaterialCoverValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, andBack-checkStaked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and GoldOptional Fuctions Hold Open Arm (9001)Parallel Rigid Cush Arm (9002)Parallel Rigid Cush and Stop Arm (9003)Extended Forearm (9004)Parallel Rigid Arm (9005)Slide Track Arm (9006)Drop Plate (90DP-PA)* Special Order from the factory Metal CoverFinish (BHMA): US3 (632), US4 (633),US26 (651), US26D (652), US32D (630)Technical DimensionsSeries 9000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from DoorSize11-7/8”11-1/8”1-1/8”2”2-3/8”End ViewFront ViewAccessories9001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount9002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open ArmPAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stop712197 NEW Door Closers 12P 2018.pdf9003Parallel RigidHold Open Cush ArmHand control plunger hold openAuxiliary stop in soffit shoe9005Parallel Rigid ArmFeatured with solid steelmain & forearm for extraheavy traffic use90DP-PASize: 11-13/16” x 3-9/16”Drop Plate –Parallel arm mountUsed to mount a closer on a top rail as narrowas 1-9/16” in height9004Extended ForearmFor Top Jamb with revealgreater than 4” and upto 8”9006Slide Track ArmFeatured with adjustableHold Open Angle90CStandard FullPlastic Cover1349Sex-bolt with screwFor 1-3/4” standard Door Thick4December 15, 2017, 11:41:38
Page - 68000 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel80008000/DAULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckAdjustable power size 1-6 with Back Check and Delay ActionApplications Extra Heavy Duty Commercial model ideal for high traffic door Versatile for new constructions, such as schools, hospitals,and public institutionsSame mounting hole pattern as LCN4041, ideal for renovationsTri-packed for all type applicationsSex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 1-6Factory preset size 3 Meet ADAProduct SpecificationOptional FuctionsCoverValves MaterialArm &BracketsScrewsFinishesHeavy Duty Cast Iron body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed,and Back-check cushionDelayed Action valve – Optional (Model: 8000/DA)Staked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, Gold, and US26D-Satin ChromeWide choice of options for different applicationsHold Open Arm (8001)Parallel Rigid Cush Arm (8002)Parallel Rigid Cush and Stop Arm (8003)Extended Forearm (8004)Parallel Rigid Arm (8005)Slide Track Arm (8006)Drop Plate (see Accessories)* Special Order from the factory Metal CoverFinish (BHMA): US3 (632), US4 (633),US26 (651), US26D (652), US32D (630)AccessoriesTechnical DimensionsSizeSeries 800011”A. Length of Closer Body5”B. Horizontal Mounting Holes1”C. Vertical Mounting Holes2-3/4”D. Height of Closer Body2”E. Projection from Door8001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount8002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open Arm5Front ViewEnd View80058003Parallel Rigid ArmParallel RigidFeatured with solid steelHold Open Cush ArmHand control plunger hold open main & forearm for extraAuxiliary stop in soffit shoe heavy traffic use8003SCParallel Rigid Hold Open Spring Cush ArmHand control plunger hold open. Spring stop in soffit shoe8004Extended ForearmFor Top Jamb withreveal between2-5/8” to 4-13/16”8006Slide Track ArmFeatured with adjustableHold Open AngleASB01Arm Support BracketUse with Cush Arms whenreveal is less than 3-1/16” (78 mm). The bracketprovides anchorage for fifth screw loadingPAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallelarm application712197 NEW Door Closers 12P 2018.pdfBSS01Blade Stop SpacerDesign to lower parallelarm shoe to clear 1/2”(13 mm) blade stop80DP-STSize: 12-1/4 x 3-9/16”Drop Plate – Pull SideHinge side mount when top rail is less than 3-3/4”Plate require 2” minimum top rail80DP-TJSize: 12-1/4 x 3-9/16”Drop Plate – Top JambUse when frame face is less than 3 1/2”Use 8004 forearm if top reveal exceeds 2-9/16”80DP-TGSize: 12-1/4 x 3-9/16”Drop Plate – Top Jambwith flush ceilingTop of head frame face in flush ceiling conditionPlate requires 1-3/4” minimum frame faceUse 8004 forearm if top reveal exceeds 2-9/16”80DP-PASize: 12-1/4 x 5”Drop Plate – Parallel ArmUse when top rail is less than5-1/2”, measured from the stopPlate requires at least 2-1/2” top rail80CStandard FullPlastic Cover1348Sex-bolt with screwDecember 15, 2017, 11:41:39
Page - 76000, 6000S SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel6000, 6000S6000/DA, 6000S/DAULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckAdjustable power size 1-6 with Back Check and Delay ActionFull CoverApplications Heavy Duty Commercial model ideal for high traffic door Versatile for new constructions, such as schools,hospitals, and public institutionsSame mounting hole pattern as NORTON 8000 CTC 12” x 3/4”,ideal for renovationsTri-packed for all type applicationsSex-bolts included for Metal Door mountingSlim CoverFeatures Multi-size spring adjustable power size 1-6,Factory preset size 3 Meet ADA Standard with adjustable BackcheckProduct SpecificationMaterialCoverValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – 6000 seriesTriple valve control for Closing speed, Latching speed, andBack-checkDelayed Action valve – Optional (Model: 6000/DA, 6000S/DA)Staked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and GoldOptional FuctionsWide choice of options for different applications Hold Open Arm (6001) Parallel Rigid Cush Arm (6002) Parallel Rigid Cush and Stop Arm (6003) Extended Forearm (6004) Parallel Rigid Arm (6005) Slide Track Arm (6006) Drop Plate (see Accessories)* Special Order from the factory Metal Cover (Full Cover only)Finish (BHMA): US3 (632), US4 (633),US26 (651), US26D (652), US32D (630)Technical DimensionsSizeSeries 6000, 6000S12-3/4”A. Length of Closer BodyB. Horizontal Mounting Holes 12”3/4”C. Vertical Mounting Holes1-1/4”D. Height of Closer Body2-1/8” End ViewE. Projection from Door6001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount6002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open ArmPAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stop712197 NEW Door Closers 12P 2018.pdf6003Parallel RigidHold Open Cush ArmHand control plunger hold openAuxiliary stop in soffit shoeFront View6005Parallel Rigid ArmFeatured with solid steelmain & forearm for extraheavy traffic use6004Extended ForearmFor Top Jamb with reveal greater than 4” and up to 8”6006Slide Track ArmFeatured with adjustableHold Open Angle60C-SStandard SlimPlastic CoverAccessories60DP-STSize: 13-1/8 x 3-1/4”Drop Plate – Pull Side , orConcealed Door HolderUse for hinge side mountUpside-down to mount where concealed doorholder prevents normal door closer mountingPlate require 2-7/16” minimum top rail60DP-TJSize: 13-1/8 x 3-5/8”Drop Plate – Top JambApply to low ceiling clearance between1-1/2” 1-3/4”60DP-PASSize: 13-1/8 x 3-5/8”Drop Plate – Parallel ArmPlate require 2-7/8” minimum top railCross reference: NORTON #314860DP-PASize: 13-1/8 x 5”Drop Plate –Parallel arm mountUsed to mount a closer on a top rail asnarrow as 3” in height1344Sex-bolt with screw60C-FStandard FullPlastic Cover6December 15, 2017, 11:41:39
Page - 84400 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel4400ULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)4400 SeriesComply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckApplications Heavy Duty Commercial model, ideal for high traffic door Versatile for new constructions, such as schools, hospitals,and public institutionsUniversal mounting hole patternSize 4: CTC 9-1/16” x 3/4”Tri-packed for all type applicationsSex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 1-6, factory preset size 3 4400 meets ADA, Barrier Free interior Standard with adjustable BackcheckProduct SpecificationOptional FuctionsCoverValves Metal CoverMaterialArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, andBack-checkStaked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and Gold Hold Open Arm (4001) Drop Plate (see Accessories)* Special Order from the factory(Slim Cover with power size 1-4 only)Finish (BHMA): US3 (632), US4 (633),US26 (651), US26D (652) , US32D (630)Technical DimensionsSeries 5000, 4400A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from DoorSize9-3/4” 9-3/4”9-1/16” 9-1/16”3/4”3/4”1-3/4” 1-3/4”2-7/8” 2-7/8” End ViewAccessories4001Hold-open ArmStand for pull sideand top jambUse with PA bracket for parallel arm mount40CStandard FullPlastic CoverHFW01Flat WrenchFor Hold Open Arm1344Sex-bolt with screwFor 1-3/4” standard Door ThickPAB02Parallel Bracketfor Hold Open Arm mounting can also usefor regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stopFront View40DP-TJSize: 9-3/4” x 2-9/16”Drop Plate –Top Jamblow ceiling clearanceFor use when ceiling clearance is between1-3/4” and 2-5/8”Cross reference: NORTON #168740DP-PASize: 9-3/4” x 3-1/2”Drop Plate –Parallelarm mountUsed to mount a closer on a top rail as narrow as 2-5/8” in height7712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:40
Page - 94000, 3000, 2000 SERIESGRADE 2ULFactory tested to meetANSI Grade 2 durabilityModel400030002000RLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)ANSI GRADE 210-Year WarrantyStandard power size 4Standard power size 3Standard power size 2Applications Medium and Light Duty model Medium Duty 4000Light Duty3000, 2000Universal mounting hole patternSize 4: CTC 9-1/16” x 3/4”Size 3: CTC 8-3/16” x 3/4”Size 2: CTC 6-5/8” x 3/4”Product SpecificationMaterialValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionDual valves control for Closing speed andLatching speed.Standard arm and parallel bracket included for differentmounting demandWood screws and machine screwsAluminum, Duronotic, and GoldTechnical DimensionsSeries 4000, 3000, 2000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from /16”6-5/8”3/4”1-3/4”2-5/8”Optional Fuctions End View4001Hold-open ArmFor 4000 SeriesPull side and top jambUse with PA bracket for parallel arm mount3001Hold-open ArmFor 3000 SeriesPull side and top jambUse with PA bracket for parallel arm mountHFW01Flat WrenchFor Hold Open Arm40CFor 4000 SeriesStandard FullPlastic CoverPAB02Parallel Bracketfor Hold Open Arm mounting can also usefor regular parallel arm application1344Sex-bolt with screwFor 1-3/4” standard Door ThickHold Open Arm (3001, 4001)Drop Plate (See Accessories)Sex-bolts (Metal door mounting)Full plastic cover, available for 4000 seriesonly (40C)Front View40DP-TJ For 4000 SeriesSize: 9-3/4” x 2-9/16”Drop Plate –Top Jamblow ceiling clearanceFor use When ceiling clearance is between1-3/4” and 2-5/8”40DP-PA For 4000 SeriesSize: 9-3/4” x 3-1/2”Drop Plate –Parallelarm mountUsed to mount a closer on a top rail asnarrow as 2-5/8” in height30DP-PA For 3000 SeriesSize: 3-1/2” x 8-3/4”Drop Plate – Parallel arm mount20DP-PA For 2000 SeriesSize: 3-1/2” x 7-5/16”Drop Plate – Parallel arm mount8712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:41
Page - 10ORDER INFORMATIONProduct AvailabilitiesSeries Power SizeDuty9000Adjustable No. 1-6Heavy9000/DAAdjustable No. 1-6Heavy8000Adjustable No. 1-6Extra Heavy8000/DAAdjustable No. 1-6Extra Heavy6000Adjustable No. 1-6Heavy6000SAdjustable No. 1-6Heavy6000/DAAdjustable No. 1-6Heavy6000S/DA Adjustable No. 1-6Heavy4400Adjustable No. 1-6Heavy4000No. 4Medium3000No. 3Light2000No. 2LightFunction AvailabilityAccessoriesSideBack Delay Hold Open with Parallel Rigid Cush & ParallelDropCheck Action Hold Open Arm Cush Arm Stop Arm Rigid Arm Track Arm PlateSex- Plastic MetalBolt Cover Coverl Standard or optionall Special order from the factory, allow for longer lead time. Please call for more informationADVANTAGE Door Closers Power SizeAdjustable Power with Back-Check (BC)AluminumProduct CodeDuroGold9000No. 1-6 BC6099106099116099128000No. 1-6 BC6088106088116088126000No. 1-6 BC6067106067116067126000S (Slim Cover)No. 1-6 BC6067306067316067324400No. 1-6 BC6044106044116044129000/DANo. 1-6 BC DA6099406099416099428000/DANo. 1-6 BC DA6088406088416088426000/DANo. 1-6 BC DA6067406067416067426000S/DA (Slim Cover)No. 1-6 BC DA6067506067516067524000No. 46040106040116040123000No. 36033006033016033022000No. 2602200602201602202Adjustable Power with Back-Check (BC) and Delay Action (DA)Fixed Power Size9712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:41
Page - 11CROSS REFERENCEADVANTAGE 90008000Spring Power Size1–61–6CTC Hole Pattern 11-1/8” x 1-1/8” 5” x 2-1/4” x 44004000300020001–61–61–643212” x ¾”12” x ¾”9-1/16” x ¾”9-1/16” x ¾”8-3/16” x ¾”6-5/8” x ¾”CR801CR801S300740730l 720440-FP430-Pl 420-Pl PR80/PR82BFDC54DC53l DC52PR80 Size 2-5Size 4Size 3Size 2100PR90416316116100100l 89168616l 7400l 7304l 7303l 7204l 7203l SC60/SC61SC64l SC93SC60 Size 2-5SC94TC200TC204TC2203HARDWAREDORMAFALCONl SC70SC81DOR-O-MATICGLOBALl TC600TC4300TC5005100520053005400l 5400l 540044CI50008050854853l 852l 754753l 752654653l 652TC400DOOR CONTROLl TC2202HAGERINTERNATIONALl TC302l 9000DOOR CLOSERLCNl 12604040Size 1-5NORTONPDQ1600l 75008501710053001100/31001100/3100l 281133111301134l BF900534533l 532l 604l 603602l 5103l 51028301ManufacturingSARGENTl 1431S.PARKER900BC814BCTAYMORl 800/800BF1900800 Size 2-5TELLl 700YALE90080044003501YMDC250160050050l 51043301YMDC1101l The same mounting hole pattern with similar application l Different mounting hole pattern in the same power sizeAll brand names & trademarks used are properties of their respective ownersULRElectromagnetic Door HolderLISTED1”MDH01EFlush Mount TypeMDH02ESurface Mount TypeØ 25/32”AEXT-011” Armature Extension Bolt(can be connected for2” & 3” long)10712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:42
Page - 12DISTRIBUTION BY:Philadelphia Hardware Group Inc.SAN DIEGO DISTRIBUTION CENTER(Home Office)6590 Top Gun StreetSan Diego, CA 92121Tel: (858) 642-0450Fax: (858) 642-0454Toll Free Tel: 1-800-545-2309Toll Free Fax: 1-800-828-0988www.philihardware.comCHICAGO DISTRIBUTION CENTER3687 Darlene CourtAurora, IL 60504Toll Free Tel: 1-800-545-2309ATLANTA DISTRIBUTION CENTER2319 Defoor Hills Road N.W.Atlanta, GA 30318Toll Free Tel: 1-800-545-2309DALLAS DISTRIBUTION CENTER4653 Leston Avenue, Suite 703Dallas, TX 75247Toll Free Tel: 1-800-545-2309Copyright 2018 Philadelphia Hardware Group Inc. All rights reserved.712197 NEW Door Closers 12P 2018.pdfDecember 15, 2017, 11:41:42
when reveal is less than 3-1/16" (78mm). (for 8000 door closer only) Top Jamb (Push side) More power-efficient than the parallel arm application Applying to a closer with narrow top rail on a door. The closer body is mounted to the frame face above the door, opposite the door hinge side. The forearm is then mounted to the top rail of the door.
