Transcription
INDUSTRIAL PLASTICS / S A F E T Y G AT EP R O D U C T D A TA Available sizessingle railSG500 UNISG630 UNISG760 UNISG890 UNIdouble railDG500 UNIDG630 UNIDG760 UNIDG890 UNIgate opening300-560561-685686-810811-940This table can be used for angle handrail systems. For pipe handrail, an additional length maybe required based upon the method the gate is attached.Single railtypeSG500 UNISG630 UNISG760 UNISG890 UNIDouble railERIKS art. n 11365075113650761136507711365078typeDG500 UNIDG630 UNIDG760 UNIDG890 UNIERIKS art. n 11373893113738941137389511373896Terms of delivery:Stock items if not soldInstallation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / S A F E T Y G AT Ep. 1/2I N S TA L L A T I O N I N S T R U C T I O N SThe ERIKS safety gate is delivered according to your specification fully pre-assembled.Drilling:The only thing to do is drilling 3 holes according to drawing on the verso of thisInstallation Instruction.Universal hinge:Whenever a wrong swing direction is ordered, it can easily be changed bywithdrawing the hinge-pin and putting the hinge block upside down.See the printed photos hereunder.Mounting hinge:1. Locate and drill 2 holes Ø18 mm for the hinge bolts, see drawing on the verso.2. Mount hinge and tighten nuts till bolts heads are flush 1 2 turn.Mounting support block:1. Locate and drill 1 hole Ø18 mm. for the block bolt, see drawing on the verso.2. Mount support block and tighten till bolt head is flush 1 2 turn.Remember you must make sure:1. Blade extends enough to make contact with opposite side handrail post, overlap 50 mm.2. Support block is mounted below the top rail of gate to prevent vertical deflection.It should not interfere with the gate or keep it from swinging closed.3. Double bar gates is no more than 1070 mm. above the platform surface to avoidtoo large of an opening below the gate.Mounting to pipe handrail:Intergate welded fixing plate during design of handrail or use adaptor set. Adaptorset available; see relevant document.Locking for wind-force:The ERIKS safety gate can easily be secured against jamming from wind-force witha simple Velcro locking device. Locking device available; see relevant document.Installation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / S A F E T Y G AT Ep. 2/2 I N S TA L L A T I O N I N S T R U C T I O N S Installation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / S A F E T Y G AT EP R O D U C T D A TA S H E E T E R I K S S A F E T Y G A T Etype:material:load bearing capacity :flame retardancy:toxicity in fire:operating temperature :Standard sizes:typeSG 500 UNISG 630 UNISG 760 UNISG 890 UNIDG 500 UNIDG 630 UNIDG 760 UNIDG 890 UNIERIKS safety gatemoulded flame retardant thermoset polyurethaneEN 14.122-3&4VO UL94 (3 mm. thick)LC13 (good) LC50 test method-40 C to 70 Cgate 86-810811-940Material specifications:Color:Density:Hardness:Fluxural strength:Fluxural modules:Izod impact strength :Heath distortion temp. :Tolerances:Others: Hardware:surface treatmentplatewedge plateboltsnutslock-pinYellow, RAL 10041.385 shore D ISO 86870 MpaASTM D7902600 MPa ASTM D7904 kJ/m2BS 2782 method 35090 CBS 2782 method 121 A/Bdimensions: 1 mm.warping: 1%weight: 5%color deviation : close to specified RAL numbernot electric conductivelow thermal conductivityvoids etc. according to our standardsuniversal L/R hingegood weather and UV resi 6. good chemical resistancy: hot-dip galvanized ISO 1461: DIN 436: DIN 435: 4.6 DIN604: 8 DIN 934: fosfatedInstallation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / S A F E T Y G AT EP R O D U C T D A TA S H E E T E R I K S S A F E T Y G A T E - A D A P T O R S E TApplication:The ERIKS safety gate can directly bemounted on a post made of squaretubing, channels or angle profile. Formounting the ERIKS safety Gate ontoround tubing you will need some adaptors as you can see onto the enclosedsketch.After the adaptor-set has beenmounted onto the posts, the safetygate and the support block can bemounted onto the angles. The adaptor-set provides a stable and rigidconstruction so that the safety gatealso can be mounted onto round handrailing, in a site adjusting situation.ERIKS has this adaptor-set availablefor 1-1/4” and 1-1/2” round pipe, resp.42,3 mm and 48,3 mm. The adaptorset exists out of two galvanized anglesand 3 U-bolts with fastening materials.The angles can be mounted on thedifferent posts with the U-bolts. Weadvice to mount the galvanized anglesat the outer sides of the handrail postsas drawn on the sketch. This way theangles are out of the walk through, soit can not create a dangerous situation.In situations where the hand railing stillhas to be manufactured, it is easier toweld plates onto the round posts.It might be necessary to order additional length, because the angles arefarther away from each other. Mosttimes this only means ordering thenext larger size.Installation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / S A F E T Y G AT EP R O D U C T D ATA S H E E T E R I K S S A F E T Y G AT E - W I N D L O C K I N G D E V I C Etypematerialoperating temperaturecolorbolting:::::ERIKS wind locking deviceVELCRO polyester barbed-tape-60 C to 150 Cblackhot-dip galvanized 8.8 DIN 604/934Application: A. Self-bonding “lasso” Velcro barbed tape 25 x 2,2B. Loop Velcro barbed tape 20 x 2,0C. Bolt, nuts and washers M16x25D. Structural steelOthers: Good weather and UV resistance. Good chemical resistance.Installation Instruction may be changed without prior notice. This literature and the information it contains are based on data reasonably believed to be reliable. However, such factors as variations in environment, application or installation, changes in operating procedures, or extrapolation of data may cause different results. ERIKS makes no representation or warranty, expressed orimplied, including warranties of merchantability or fitness of purpose, as to the accuracy, adequacy or completeness of the recommendations or information contained herein. ERIKS assumesno liability whatsoever in connection with this literature or the information or recommendations it contains.For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 w w w. e r i k s . b e
INDUSTRIAL PLASTICS / SAFETY GATE For more information, prices or ordering conditions, please contact directly one of our specialists on tel. number: 03 829 27 50 ERIKS nv Boombekelaan 3 2660 Hoboken tel. (03) 829 26 11 fax (03) 828 39 59 www.eriks.be Application: The ERIKS safety gate File Size: 411KBPage Count: 6
