WIXLIB

When the code official shall have first obtained a proper inspection warrant or other remedyprovided by law to secure entry, no owner, occupant, or person having charge, care of control ofany building or premises shall fail or neglect, after proper request is made as herein provided, topromptly permit entry therein by the code official for the purpose of inspection and examinationpursuant to this code.It shall be unlawful for any person to hinder or interfere with the code official, deputy or anyof the inspectors in the discharge of their duties under this code.C110.2. 4 Occupancy violations. Whenever any site, building, structure or equipment thereinregulated by this code or any other code is being used contrary to the provisions of this code orany other code, the code official may order such use discontinued and the structure, or portionthereof, vacated by notice served on any person causing such use to be continued.Such person shall discontinue the use within the time prescribed by the code official afterreceipt of such notice to make the site, building, structure, or portion thereof, or equipmentcomply with the requirements of this code.C110.2. 5 Liability. The code official, member of the board of appeals or employee chargedwith the enforcement of this code, while acting for the jurisdiction in good faith and withoutmalice in the discharge of the duties required by this code or other pertinent law or ordinance,shall not thereby be rendered liable personally and is hereby relieved from personal liability forany damage accruing to persons or property as a result of any act or by reason of an act oromission in the discharge of official duties. Any suit instituted against an officer or employeebecause of an act performed by that officer or employee in the lawful discharge of duties andunder the provisions of this code shall be defended by legal representative of the jurisdictionuntil the final termination of the proceedings.The code official or any subordinate shall not beliable for cost in any action, suit or proceeding that is instituted in pursuance of the provisions ofthis code. Any judgment resulting therefrom shall be assumed by this jurisdiction.C110.2. 5. 1 The liability exemption and defense protection provided in this section arenot extended to Third Party Companies, or their employees.C110. 2. 5. 2 This code shall not be construed to relieve from or lessen the responsibility ofany person owning, operating or controlling any building or structure for any damages topersons or property caused by defects, nor shall the code enforcement agency or its parentjurisdiction be held as assuming any such liability by reason of the inspections authorized bythis code or any permits or certificates issued under this code.C110. 2. 6 Modifications. Wherever there are practical difficulties involved in carrying outthe provisions of this code, the code official shall have the authority to grant modifications forindividual cases, upon application of the owner or owner' s representative, provided the codeofficial shall first find that special individual reason makes the strict letter of this codeimpractical and the modification is in compliance with the intent and purpose of this code andOrdinance No. 22520- 12- 2016Page 7of37

that such modification does not lessen health, accessibility, life and fire safety, or structuralrequirements. The details of any action granting modifications shall be recorded and entered inthe files of the department.C110. 2. construction.provisions of this code are not intended to prevent the installation of any material or to prohibitany design or method of construction not specifically prescribed by this code, provided that anysuch alternativehas beenapproved.An alternative material, design or method of constructionshall be approved where the code official finds that the proposed design is satisfactory andcomplies with the intent of the provisions of this code, and that the material, method or workoffered is, for the purpose intended, at least the equivalent of that prescribed in this code inquality, strength, effectiveness, fire resistance, durability and safety.C110. 2. 8 ResearchSupporting data, where necessary to assist in the approval ofmaterials or assemblies not specifically provided for in this code, shall consist of valid researchreports.reports from approved sources.C110. 2. 9 Tests. Whenever there is insufficient evidence of compliance with the provisionsof this code, or evidence that a material or method does not conform to the requirements of thiscode, or in order to substantiate claims for alternative materials or methods, the code officialshall have the authority to require tests as evidence of compliance to be made at no expense toTest methods shall be as specified in this code or by other recognized testthis jurisdiction.standards. In the absence of recognized and accepted test methods, the code official shall approvetestingprocedures.Testsbeby an approved agency. Reports of suchshall be retained by the code official for the period required for retention of public records.theC110. 2. 10 Materialshallperformedand equipment reuse.testsMaterials, equipment and devices shall not bereused unless such elements have been reconditioned, tested, placed in good and proper workingcondition, and approved.C110. 2. 11 Cooperation of other officials and officers. The code official may request, andshall receive, the assistance and cooperation of other officials of this jurisdiction so far as isrequired in the discharge of the duties required by this code or other pertinent law or ordinance.IECC SECTION C111IECC Section Cl H; added to read as follows:C111 Violations.It shall be unlawful for any person, firm or corporation to erect, construct,move, improve, remove, convert or demolish, equip, use, occupy ormaintain any building or structure or cause or permit the same to be done in violation of thisenlarge,alter,repair,code.Ordinance No. 22520- 12- 2016Page 8of37

Any violation cited under the Building Code, Residential Code, Electrical Code, MechanicalCode and Plumbing Code, as adopted elsewhere, that is also associated with energy- efficientprovisions of this code, may also be cited as a violation of this code.Any person who violates a provision of this code or fails to comply with any of thethereof or who erects, constructs, alters or repairs a building or structure inrequirementsviolation of the approved construction documents or directive of the code official, or of a permitor certificate issued under the provisions of this code, shall be subject to penalties as prescribedby law.Each day or any portion thereof during which any violation of this ordinance occurs orcontinues shall be deemed a separate offense and upon conviction thereof shall be punishable asprescribed by law.CHAPTER 2 [ CE] —DEFINITIONSIECC SECTION C202DEFINITIONSIECC Section C202; the followitZg definitions are changed or are added to readas follows:BUILDING CODE.Building Code shall mean the International Building Code as adopted bythis jurisdiction.CHANGE OF OCCUPANCY.thatinvolvesa changeinA change in the purpose or level of activity within a buildingapplication oftherequirements ofthiscode.The definition shall alsoapply to the usage of the surrounding site and access to and from the building, structure or site,as necessary to achieve the purpose of this code, and to obtain compliance with other codes andordinances of this jurisdiction.ELECTRICAL CODE. Electrical Code shall mean the National Electrical Code as adopted bythis jurisdiction.For the purpose of this code, all references to NFPA 70 shall be assumed tomean the Electrical Code as defined herein.ENERGY CODE. Energy Code shall mean the International Energy Conservation Code asadopted by this jurisdiction.FIRE PREVENTION CODE ( FIRE CODE).Fire Prevention Code, or Fire Code, shall meanthe International Fire Code as adopted by this jurisdiction.FORT WORTH BUILDING ADMINISTRATIVE CODE.The Fort Worth Administrativecode containing the administrative, organizational, and enforcement rules and regulations for theOrdinance No. 22520- 12- 2016Page 9of37

Fort Worth Building, Residential, Plumbing, Fuel Gas, Mechanical, Electrical, Sign and ExistingBuilding codes.FUEL GAS CODE.this jurisdictionFuel Gas code shall mean the International Fuel Gas Code as adopted bybe considered as part of the Plumbing Code. ( See Plumbing Code.)and shallHISTORIC BUILDING.Buildings that are listed in or eligible for listing in the NationalRegister of Historic Places, or designated or eligible for designation as historic under anappropriate state or local law.MECHANICAL CODE.Mechanical Code shall mean the International Mechanical Code asadopted by this jurisdiction.PLUMBING.For the purpose of using the International Plumbing Code, or the PlumbingSection of the International Residential Code, as adopted, shall mean:The practice, materials and fixtures utilized in the installation, maintenance, extensionand alteration of all piping, fixtures, plumbing appliances and plumbing appurtenances,or adjacent to any structure, in connection with sanitary drainage or stormdrainage facilities; venting systems, and public or private water supply systems.withinFor the purpose of complying with the Texas State Plumbing License Law, shall mean:All piping, fixtures, appurtenances, and appliances, including disposal systems, drain orwaste pipes, or any combination of these that:supply, recirculate, drain, or eliminate water, gas, medical gasses and vacuum,liquids, and sewage for all personal or domestic purposes in and about buildings wherepersons live, work, or assemble; connect the building on its outside with the source ofwater, gas, or other liquid supply, or combinations of these, on the premises, or the watermain on public property; and carry waste water or sewage from or within a building tothe sewer service lateral on public property or the disposal or septic terminal that holdsprivate or domestic sewage.The ,orrenovationofallpiping, fixtures, appurtenances, and appliances on premises where persons live, work, orassemble that supply gas, medical gasses and vacuum, water, liquids, or any combinationof these, or dispose of waste water or sewage.PLUMBING CODE.Plumbing Code shall mean the International Plumbing Code and theInternational Fuel Gas Code as adopted by this jurisdiction. The term " Plumbing Code" appliesto both codes as one combined code.PLUMBING SYSTEM. For the purpose of using this code, as adopted, shall mean:Includes the water supply and distribution pipes, plumbing fixtures and traps, supports andappurtenances; water-treating or water-using equipment; soil, waste and vent pipes; sanitarydrains, storm sewers and building sewers to an approved point of disposal, in addition to theirrespective connections, devices and appurtenances within a structure or premise.Ordinance No. 22520- 12- 2016Page 10of37

PROJECTION aveorpermanently attached shading device, divided by the distance measured vertically from thebottom of the fenestration glazing to the underside of the overhang, eave or permanently attachedshading device. ( See IECC Equation 4- 5)RESIDENTIALBUILDING.For thisincludes detachedfamilyfamilybuildings three stories or less in height above grade. Residential buildings on a Podium building,not exceeding three stories in height above the podium level, may also be considered asResidential Buildings if constructed the same as they would be if on grade with no dwellings ( townhouses) as well as R-2, R-3 and R- 4shafts, interior stair shafts, etc. that would connect conditioned residential space above with thepodium level below.RESIDENTIAL CODE.Residential Code shall mean the International Residential Code asadopted by this jurisdiction.CHAPTER 3 [ CE] — GENERAL REQUIREMENTSIECC SECTION C303MATERIALS, SYSTEMS AND EQUIPMENTIECC Section C303. 2. 1; deleted and replaced to read as follows:303.2. 1 Protectionfoundation insulation.Becauseheavy" termiteclassification, designs employing exterior insulation of basements or slabs shall not be utilized.of exposedof " veryCHAPTER 4 [ CE] —COMMERCIAL ENERGY EFFICIENCYIECC SECTION C402BUILDING ENVELOPE REQUIREMENTSIECC Section C402. 1. 1; add an item 4 to read as follows:4. (life safety) In order to provide a tenable work environment in unheated warehouses,heaters that exceed the energy limitations of item I or 2 above may be installed in thedock area without requiring the entire warehouse to comply with the envelope provisions,with the following stipulations:Ordinance No. 22520- 12- 2016Page 11of37

a.b.This exemption shall not apply if heaters are installed throughout the entirewarehouse, even ifjust to prevent pipe freezing.This provision shall not apply to other conditioned spaces inside the warehouse, e. g.offices, restrooms, break rooms, etc. which must individually be separated from thewarehouse with a compliant envelope.c.Loading Dock weather seals of Section C402. 5. 6 must be installed.IECC Section C402. 2. 2. 1; added to read as follows:C402. 2. 2. 1 Atticequipment.Where equipment installed in the attic is required aworking area and access pathway in accordance with this or other codes, as applicable,the insulation under such walkway or platform shall not be reduced unless compensatedfor through an approved method such as the usage of a performance ( computer) energyreview compliance report.IECC Section C402. 2. 7; added to read as follows:C402. 2. 7 Insulation installed inwalls.To insure that insulation remains in place,insulation installed in walls shall be totally enclosed on all sides consisting of framinglumber, gypsum, sheathing, wood structural panel sheathing, netting or other equivalentmaterial approved by the building official.IECC Section C402. 4. 1; an exception is added to read as follows:C402. 4. 1 Maximum Area.The vertical fenestration area ( not including opaque doorsand opaque spandrel panels) shall not be greater than 30 percent of the gross above- gradewall area. The skylight area shall not be greater than 3 percent of the gross roof areaException:under( lifesafety) When installing the minimum smoke and heat vents requiredarea of such vents ( skylights) may exceed 3%, but only byFire Code Section 910, thethe amount needed to meet the requirement of that section.IECC Section C402. 4. 1.] added to read as follows:C402. 4. 1. 1 Roll upRoll up or roll away walls, doorsor folding doors and windows providing access for the interioratmosphere, conditioned air and/ or noise to flow to the outside, usually associatedwith interior assemblies connecting to outside dining, patio or sidewalk area, will notoror rollawaywall sections.windows,be accepted.Ordinance No. 22520- 12- 2016Page 12of37

Exception:Such openings may be accepted when all of the followingconditions are met:1.A kill switch is associated with each opening such that the airconditioning and/ or heat is deactivated when the door/window is This deactivationdoes not apply to the kitchen area.In the following zonings ( H, NS, TU, MU- 1, MU-2, and any new formbased zoning adopted by Council), as defined in the Zoning Code,such openings may be used for any size tenant space.In other zonings, such openings are only permitted in tenant spacesless than 3, 000 sq.ft. or in a portion of the tenant space that has beensubdivided with a partition and doors to be less than 3, 000 sq.ft.IECC Section C402. 5. 7; an exception is added to read as follows:C402. 5. 7 Vestibules.Building entrance shall be protected with an enclosed vestibule,with all doors opening into and out of the vestibule equipped with self-closing devices.Vestibules shall be designed so that in passing through the vestibule it is not necessary for theinteriorandexteriordoors toopenatthesametime.The installation of one or morerevolving doors in the building entrance shall not eliminate the requirement that a vestibulebe provided any doors adjacent to revolving doors.Exception:Vestibules are not required for the following:1.Buildings in Climate Zones 1 and 2.2.Doors not intended to be used by the public, such as doors to mechanicalor electrical equipment rooms, or intended solely for employee use.Doors opening directly from a sleeping unit or dwelling unit.Door that open directly form a space less than 3, 000 square feet ( 298 m2)3.4.in area.5.6.Revolving doors.Doors that have an air curtain with a velocity of not less than 6. 56 feet persecond (2m/ s)at the floor that have been tested in accordance withASNI/AMCA 220 and installed in accordance with the manufacturer' sinstructions.operatetheManual or automatic controls shall be provided that willaircurtainwiththe openingandclosingofthe door.AirCurtains and their controls shall comply with Section C408. 2. 37. ( life safety) Doors provided for and only used as Fire Accessaccordance with Fire Code Section 903. 2. 11. 1 or 2306. 6. 1.openings inIECC SECTION C405ELECTRICAL POWER AND LIGHTING SYSTEMSOrdinance No. 22520- 12- 2016Page 13of37

IECC Section C405. 2; changed to read as follows:C405. 2Lightingcontrols (Mandatory). Lighting systems shall be provided with controls asspecified in Sections C405. 2. 1, C405. 2. 2, C405. 2. 3, C405. 2. 4 and C405. 2. 5Exceptions:1.Lighting controls are not required for the following:Areas designated as security or emergency areas that must be continuously lighted,inclusive of areas of incarceration.2.Interior exit stairways, interior exit ramps, and exit passageways.3.Emergency egress lighting that is normally off.IECC Section C405. 5. 1; changed to read as follows:C405. 5. 1 Exterior building lighting power. The total exterior lighting power allowancefor all exterior building applications is the sum of the base

THE 2015 INTERNATIONAL ENERGY CONSERVATION CODE, WITH LOCAL AMENDMENTS; AMENDING SECTIONS 7-41, 7-42, 7-43 AND 7-44 OF THE CODE OF . The provisions of the Building Code, Residential Code, Electrical Code, Mechanical Code, and Plumbing Code, as adopted elsewhere, shall be used as part of this code for any provision, .