WIXLIB

Risk of Electrocutionplug still does not fit, contact a qualified electrician toinstall the proper wall outlet. Do not modify the applianceplug, power cord receptacle, or power cord plug in anyway.m Inspect cord before using. Do not use if cord is damaged. Keep all connections dry and off the ground.mWARNING Do not touch plug with wet hands. Keep cord away from heat and sharp edges. Do not spray electrical apparatus and wiring.Electric shock may cause SEVERE INJURY orDEATH. Heed these warnings:Risk of Explosion Do not allow any part of the electric pressure washerto make contact with water while it is in operation. Ifthe appliance becomes wet while turned off, wipe drybefore starting. Do not spray flammable liquids. Do not use acids, bases, solvents, or any flammablematerial in this product. These substances can causephysical injuries to the operator and irreversible damage tothe machine. Do not use an extension cord over 25 ft. Thepressure washer comes equipped with a 35 ft powercord. Combined cord length must not exceed 60 ft.Any extension cord must be 14-gauge (or heavier) tosafely power the pressure washer.Additional Safety Instructions High-pressure: keep clear of nozzle. Do not touch the appliance or its plug with wet handsor while standing in water. Wearing rubber bootsoffers some protection. Injection hazard: equipment can cause serious injury if thespray penetrates the skin. Do not point the gun at anyone or at any part of the body.EXTENSION CORD CHART In case of skin penetration, seek medical aid immediately.Cord Length:25 ft (7.6 m)Min. Wire Gauge (A.W.G.):14 Before servicing, cleaning, or removing any parts, shut offthe power and relieve pressure. This machine is not suitable for connection to the potablewater mains.6. To prevent the appliance cord from disconnecting from theextension cord during operation, make a knot with the twocords as shown in Table 1.Product DescriptionPurposeTable 1. Method of Securing Extension CordCord set This high-pressure electric power washer is intended forresidential use to clean vehicles, machines, buildings,facades, etc.Appliance cordAreas of Application Never use the machine in potentially explosive areas underany circumstances!(A) Tie cord as shown The operating temperature must be between 32ºF (0ºC) and104ºF (40ºC). The machine consists of an assembly with a pump, whichis encased in a shock-absorbing housing. To provide theoperator with an optimal working position, the machine isequipped with a spray wand and a non-slip handle grip,whose shape and configuration comply with applicableregulations.(B) Connect plug and receptacle7. Do not abuse the cord. Never pull the pressure washerby the cord or yank the cord to disconnect it from thereceptacle. Keep the cord away from heat, oil, andsharp edges. Do not cover or modify the spray wand or the spray nozzlesin any way. The high-pressure electric power washer is designed to beused with cold or lukewarm water; higher temperatures candamage the pump. Do not use water that is dirty, gritty, or contains anychemical products, as these could impair operation andshorten the life of the machine.3

Safety SymbolsThe following table depicts and describes safety symbols that may appear on this product. Read, understand, and follow allinstructions on the machine before attempting to assemble and operate.SymbolsDescriptionsSymbolsDescriptionsREAD THE OPERATOR'SMANUAL(S) – Read, understand,and follow all instructions in theuser manual(s) before attemptingto assemble and operate.WARNING! Electrical shock hazard –Do not touch the plug with wet hands.SAFETY ALERT – Indicates aprecaution, a warning, or a danger.WARNING! Do not expose the unitto rain or wet conditions. Keep dry.WEAR EYE AND HEARINGPROTECTION – For protectionagainst injury, wear ear defendersand safety goggles.To reduce the risk of injury, usermust keep all bystanders at least49 ft (15 m) away.Wear safety gloves duringuse to protect hands.Wear non-slip footwear that willprotect your feet and improve yourfooting on slippery surfaces.Store indoors. Never store thepressure washer outdoors.If the pump freezes, permanentdamage may result.Machine not suitable for connectionto the potable water mains.Always keep the power cordaway from heat sources, oils, orsharp edges. Immediately removeplug from the mains if the cord isdamaged, frayed, or entangled.WARNING! Turn the machine OFFand disconnect it from the powersupply before inspecting, cleaning,changing accessories, or conductingany other maintenance task.Sound power level is 96 dB(A).Double Insulation – When servicing,use only identical replacement parts.4

Know Your Electric Pressure WasherRead the owner’s manual and safety instructions carefully before operating the electric pressure washer. Compare the illustrationbelow to the electric pressure washer in order to familiarize yourself with the location of the various controls and adjustments.Save this manual for future reference.1. Transport handle12. Trigger gun3. Safety lock (Locate lock in center of trigger.Pull up and snap in place. See Fig. 12, pg. 8)24. Trigger35. High-pressure hose connection46. Trigger gun holder7. Spray wand128. Detergent dial59. ON/OFF switch (Pressure select dial)1310. Water inlet Garden hose adapter (female coupler)11. Detergent tank12. High-pressure hose13. Hose holder14. Cord holder615. Power cord with GFCI716. Wheel (x2)17. Needle clean-out tool149818. 0º Quick-Connect nozzle (orange)1519. 15º Quick-Connect nozzle (yellow)20. 25º Quick-Connect nozzle (green)1021. 40º Quick-Connect nozzle (gray)22. Soap Quick-Connect nozzle l DataRated Voltage120 V 60 HzMax. Pressure2030 PSI (14 MPa)Motor14.5 amp (1800 W)Detergent Tank Capacity54.1 fl oz (1.6 l)Max. Water Inlet Temperature104ºF/40ºCHose Length20 ft (6 m)Max. Water Inlet Pressure0.7 MPaPower Cord Length35 ft (10.7 m)Max. Flow1.76 GPMWeight27.8 lbs (12.6 kg)Rated Pressure1450 PSI5

Unpacking3. Slide the upper handle frame into lower handle thendepress the small button at the end of the upper handleframe, push and insert into lower handle until it snapssecurely into place (Figs. 2 – 3).Carton Contents Upper handle frame hose holder assemblyFig. 2 Lower handle pressure washer assembly Trigger gun Spray wand Five (5) Quick-Connect nozzles (0º, 15º, 25º, 40º and Soap) Trigger gun holderUpperhandleframe Needle clean-out tool High-pressure hose Garden hose adapter (female coupler) Manual with registration card1. Carefully remove the pressure washer and check to seethat all of the above items are supplied.Lowerhandle2. Inspect the product carefully to make sure no breakage ordamage occurred during shipping. If you find damaged ormissing parts, DO NOT return the unit to the store. Pleasecall the Snow Joe Sun Joe customer service center at1-866-SNOWJOE (1-866-766-9563).NOTE: Do not discard the shipping carton and packagingmaterial until you are ready to use your new electricpressure washer. The packaging is made of recyclablematerials. Properly dispose of these materials inaccordance with local regulations.IMPORTANT! The equipment and packaging material arenot toys. Do not let children play with plastic bags, foils,or small parts. These items can be swallowed and pose asuffocation risk!Fig. 3mWARNING! Do not connect to power supply untilassembly is complete. Failure to comply could result inaccidental starting and possible serious personal injury.PushbuttonAssemblyUpperhandleframe1. Position the washer as CLOSE as possible to thewater supply.2. The washer must be used on a secure and stable surfacein a standing, upright position (Fig. 1).LowerhandleFig. 16

mWARNING! Keep hose away from sharp objects.4. Connect the high-pressure hose to the water outlet on thewasher (Fig. 4).Fig. 4Bursting hoses may cause injury. Examine hoses regularly andreplace if damaged. Do not attempt to mend a damaged hose.(REAR)7. Connect the garden hose adapter (female coupler)to the water inlet of the pressure washer, then threadyour garden hose (male end) into the garden hoseadapter (Figs. 7 – 8). The garden hose must have aninternal diameter of at least 13 mm (1/2 in.) and must bereinforced. The water supply must be at least equal to thewasher delivery capacity.NOTE: The machine is not suitable for connection to thepotable water main.High-pressure hoseFig. 7High-pressurewater outlet(FRONT)Water inlet(female coupler)5. Fit the spray wand into the trigger gun and rotate it untilthe two parts are completely locked (Fig. 5).Garden hose adapter(female coupler)Fig. 5Trigger gunGarden hose(male end)This end to thewater inlet onthe unitSpray wandFig. 8Garden hose adapter(female coupler)6. Connect the high-pressure hose to the trigger gun(Fig. 6).Fig. 6Garden hoseHigh-pressure hose(FRONT)Trigger gun7

8. Attach garden hose to water supply (Fig. 9).10. Check that the electrical supply voltage and frequency(Volt/Hz) correspond to those specified on the pressurewasher rating plate. If the power supply is correct, youmay now plug the pressure washer into the power outlet(Fig. 11).Fig. 9Fig. 11Connect to water supplyResetGarden hoseTSEREGFCImWARNING! Do not connect to potable water system.mWARNING! If connection is made to a potable waterSTTEPower lightindicatorsystem, the system shall be protected against backflowmWARNING! The intake water temperature must notNOTE: The GFCI may need to be reset when first pluggedinto the electric outlet. Press the "Reset" button until thepower light indicator on the GFCI illuminates.exceed 104ºF/40ºC. The water supply must not exceed0.7 MPa.mCAUTION! The washer must only be used with cleanOperationmIMPORTANT! This pressure washer is equipped withwater; use of unfiltered water containing corrosivechemicals will damage the washer.9. Make sure the ON/OFF switch (pressure select dial) ispushed to the STOP (0) position before plugging the unitinto the power outlet (Fig. 10).Fig. 10WLOSTOP0HIa micro-switch sensitive to water flow. This Total Stop System(TSS) senses water flow in the pump. When the trigger isreleased, water stops flowing through the pump. The TSS thenautomatically turns the motor off to protect the pump fromoverheating, thus saving energy and prolonging pump life.1. Turn the water supply tap on completely.GH2. Make sure the safety lock is down and in its originalposition (Fig. 12), then press the trigger for a few secondsuntil water flow is steady. This will allow air to escape anddischarge any residual pressure in the hose.Fig. 12SlotSafety lock8Trigger

3. Turn the ON/OFF switch (pressure select dial) to the LOW (I)or HIGH (II) position to start the pressure washer (Fig. 13).Fig. 13WSTOP0LO3. Snap the desired nozzle onto the Quick-Connect collaruntil it clicks into place (Fig. 15).HIFig. 15Spray wandNozzleGH“Click”Quick-Connect collarTo disconnect a nozzle from the spray wand once the cleaningjob is complete:4. Turn off the pressure washer and shut off the water supply.Pull the trigger to release water pressure.5. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 14).Using the NozzlesBefore beginning any cleaning task, determine the best nozzlefor the job. Each of the nozzles has a different spray pattern.The nozzle patterns are 40 (for gentle cleaning), 25 (forall-purpose cleaning), 15 (for tough jobs), 0 (for spot cleaningor hard-to-reach areas) and the Soap nozzle (for detergentapplication).6. Remove the nozzle by placing your hand over the nozzlewhile pulling back on the Quick-Connect collar.mWARNING! Do not make changes to the nozzle whilethe trigger is engaged. Doing so could result in damage to thepressure washer or injury to the user.mCAUTION! NEVER change nozzles without locking theWorking with Detergentssafety lock on the trigger handle.When cleaning with the pressure washer, some cleaning taskscan be solved with water alone, but for most tasks cleaningwith detergent allows for more effective dirt removal.mWARNING! High-pressure jets can be dangerous ifsubject to misuse. The jet must not be directed at persons,pets, live electrical equipment, or the appliance itself.mWARNING! Use only detergents specifically designedThis electric pressure washer is equipped with five (5)Quick-Connect nozzles that easily snap onto theQuick-Connect collar of the spray wand.for use with pressure washers. DO NOT USE householddetergents, acids, alkaline solutions, bleaches, solvents,flammable material, or industrial grade solutions. These coulddamage the pressure washer. Many detergents may requiremixing prior to use. Prepare the cleaning solution as instructedon the solution bottle.To connect a nozzle to the spray wand:1. Turn off the pressure washer and shut off the water supply.Pull the trigger to release water pressure.1. Remove the cap from the detergent tank and fill the tankwith detergent (Fig. 16).2. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 14).Fig. 16Fig. 14SlotPressure washerdetergentSafety lock9Detergenttank

2. Install the soap nozzle (black) on the spray wand (Fig. 15).3. Engage the safety lock on the trigger handle by pushingup on the safety lock until it clicks into the slot (Fig. 14).3. Turn on the pressure washer. Pull the trigger to operatethe unit. The liquid detergent will automatically mix withwater and be discharged through the nozzle.4. Remove the nozzle by placing your hand over the nozzlewhile pulling back on the quick-connect collar.5. Select the right nozzle for the job (Fig. 18):mCAUTION! Always test the detergent in aninconspicuous area before use.Fig. 184. Turn the detergent dial to adjust the suction volume of thedetergent solution (Fig. 17).Fig. 17MIN0º15ºDetergent dial25º40ºSOAMAXPI) The 0º intense-jet nozzle (orange) is an extremelypowerful nozzle that delivers a high-pressure, pencilpoint jet stream. It is used to cut heavy dirt depositsin a small, concentrated area. It is ideal for dissolvingstubborn substances, like tar and grease spots onconcrete, or for removing caked mud from equipment.Use this nozzle to clean hard-to-reach areas includingthe facades of 2-story buildings or the undersides oflawn mowers and tractors.5. Apply detergent from the bottom to the top of the drysurface to be cleaned.NOTE: Wetting the surface first is not recommended as itdilutes the detergent and reduces its cleaning ability.6. Allow the detergent to remain on the surface for a shorttime before rinsing. Do not allow the detergent to dry onthe surface.NOTE: Care should be used when choosing theright nozzle to avoid permanently gouging wood ordamaging fragile surfaces.mCAUTION! Damage may occur to painted surfaces ifII) Use the 15º fan-tip nozzle (yellow) for intense cleaningjobs on hard surfaces. Applications include strippingpaint, removing oil stains, grease, heavy mildew stains,and rust from steel. This nozzle should only be used inareas that can withstand the high-pressure from thisnozzle.the detergent is allowed to dry on the surface. Wash and rinsea small section at a time. Avoid working on hot surfaces or indirect sunlight.7. When finished using the pressure washer, you must firstdrain and rinse the detergent tank. Run the pressurewasher in low pressure until all of the soap is drained fromthe detergent tank.III) Use the 25º fan-tip nozzle (green) to clean home siding,brick patios, wood decks, driveways, or sidewalks.When using this nozzle, test a small area first to avoidsurface damage.mCAUTION! Failure to follow these cleaning instructionsIV) Use the 40º wide-spray tip nozzle (gray) to clean itemssuch as cars, trucks, boats, patio furniture, or lawnequipment.will cause the injection system to become clogged andinoperable.Rinsing with the Pressure Washer1. Turn off the pressure washer and shut off the water supply.2. Pull the trigger to release water pressure.V) Use the Soap nozzle (black) for low-pressure detergentapplication to clean equipment, remove mildew andoxidation stains from houses, clean bricks or degreasegrimy surfaces.NOTE: When using detergent, make sure to install thecorrect Soap nozzle (black). All of the other colorednozzles will not work for detergent application.6. Start at the top of the area to be rinsed and work your waydown, making sure to overlap your strokes.10

mIMPORTANT! NEVER USE:Winterizing Long-Term Storage Bleach, chlorine products, and other corrosive chemicalsIf you must store your pressure washer in a location wherethe temperature falls below 32ºF (0ºC), you can minimize thechance of damage to your machine by utilizing the followingprocedure: Liquids containing solvents (e.g. paint thinners, gasoline,oils) Tri-sodium phosphate products Disconnect all water connections. Ammonia products Turn on the machine for a few seconds until the remainingwater in the pump exits. Turn off immediately. Acid-based productsThese chemicals will harm the unit and will damagethe cleaning surface. Do not allow the high-pressure hose to become kinked. Store the machine and accessories in a room that doesnot reach freezing temperatures.Shutting Down Do not store near a furnace or other sources of heat thatmay dry out the pump seals.1. Turn the switch to the STOP (0) position and unplug thepower cord from the outlet. Operate the pressure washer with non-corrosive/non-toxicanti-freeze, a pump saver, or a pump protector beforestoring for the winter.2. Turn off the water source.3. Hold the trigger to release water pressure.4. Disconnect the garden hose from the water inlet onthe unit.mWARNING! Before reusing, completely flush the unitout with clear water. Anti-freeze products can damagepaintwork, so you must ensure there is no anti-freeze left in thesystem before using it again.5. Disconnect the high-pressure hose connection on thetrigger gun handle.6. Release the trigger and engage the gun safety lock.MaintenancemCAUTION! Before working on the pressure washer,mWARNING! Turn off the water supply and squeeze thetrigger to depressurize the unit. Failure to do so could result inpersonal injury due to discharge of high-pressure water.disconnect the plug from the power supply socket.1. To ensure good performance, check and clean the waterinlet filter (Fig. 19). Remove the pre-filter and water inletfilter and rinse with warm water to prevent any foreignmatter from clogging the pump (Figs. 20 – 21).Taking a BreakIf you are taking a break of five minutes or more betweencleaning tasks:1. Engage the gun safety lock (Fig. 14).Fig. 192. Turn the switch to the STOP (0) position.3. Unplug the power cord from the outlet.(FRONT)Water inlet filterStoragemCAUTION! Always store your pressure washer in alocation where the temperature will not fall below 32ºF (0ºC).The pump in this machine is susceptible to permanent damageif it freezes. FREEZE DAMAGE IS NOT COVERED BY THEWARRANTY.Garden hose adaptorPre-filter Store the pressure washer indoors in a dry, covered areawhere it is not subject to adverse weather conditions.Fig. 20 It is important to store this product in a frost-free area. Always empty water from all hoses, the pump, and thedetergent bottle(s) before storing.mCAUTION! The use of a pump protector isPre-filterrecommended to prevent cold weather damage during storageover the winter months.11

Service SupportFig. 21If your Martha Stewart MTS-2030PW electric pressure washerrequires service or maintenance, please call the Snow Joe Sun Joe customer service center at 1-866-SNOWJOE(1-866-766-9563).Inlet filterModel Serial NumbersWhen contacting the company, reordering parts, or arrangingservice from an authorized dealer, you will need to provide themodel and serial numbers, which can be found on the decallocated on the housing of the unit. Copy these numbers intothe space provided below.2. Clean the nozzle with the needle clean-out tool provided(Fig. 22). Remove the spray wand from the gun; removeany dirt from the nozzle hole and rinse.Record the following numbers from the housing or handle of yournew product:M T S - 2 0 3Fig. 22Model #:0 P WSerial #:15ºFederal CommunicationsCommission (FCC)mWARNING! Any changes or modifications to thisNeedle clean-out toolunit not expressly approved by the party responsible forcompliance could void the user's authority to operate theequipment.Class B device:NOTE: This equipment has been tested and found to complywith the limits for a Class B digital device, pursuant to part 15of the FCC Rules.3. Remove additional debris by back flushing water throughthe nozzle and spray wand. To do this, place the end ofyour garden hose (with water running) to the tip of thenozzle, pushing water and debris out of the back openingof the nozzle and spray wand.These limits are designed to provide reason

Know your product – Know how to stop the machine and bleed pressure quickly. Thoroughly familiarize yourself with the controls. Keep bystanders away – All visitors and pets should be kept a safe distance away from the work area. Use the right product – Do not use this