Transcription
PROHEAT 2X REVOLUTIONPETPROUSER GUIDE2066 SERIES
IMPORTANT SAFETY INSTRUCTIONSREAD ALL INSTRUCTIONS BEFORE USING YOUR DEEP CLEANER.When using an electrical appliance, basic precautions should be observed, including the following:WARNINGTo reduce the risk of fire, electricshock, or injury:» Unplug from electrical socket when not in useand before cleaning, maintaining or servicing theappliance.» This appliance can be used by children aged from8 years and above and persons with reducedphysical, sensory or mental capabilities or lackof experience and knowledge if they have beengiven supervision or instruction concerning use ofthe appliance in a safe way and understand thehazards involved. Cleaning and user maintenanceshall not be made by children without supervision.» Children should be supervised to ensure thatthey do not play with the appliance.» If the supply cord is damaged, it must bereplaced by the manufacturer, its service agentor similarly qualified persons in order to avoid ahazard.» Do not run appliance over cord.» Keep hair, loose clothing, fingers, and all parts ofbody away from openings and moving parts ofthe appliance and its accessories.» Use only the type and amount of liquids specifiedunder the Operations section of this guide.» Do not leave appliance when plugged in.» Always connect to a properly earthed electrical socket. Do not modifyearthed plug.» Do not allow to be used as a toy.» Use only as described in the user guide.» Use only manufacturer’s recommended attachments.» Do not use with damaged cord or plug.» Do not immerse in water or liquid. Use only on surfaces moistened by thecleaning process.» If appliance is not working as it should, has been dropped, damaged, leftoutdoors, or dropped into water; do not attempt to operate it and have itrepaired at an authorized service center.» Liquid must not be directed towards equipment containing electricalcomponents.» Do not pull or carry by cord, use cord as a handle, close door on cord, orpull cord around sharp edges or corners.» Keep cord away from heated surfaces.» Do not unplug by pulling on cord.» To unplug, grasp the plug, not the cord.» Do not handle plug or appliance with wet hands.» Do not put any object into openings.» Do not use with any opening blocked; keep free of dust, lint, hair, andanything that may reduce air flow.» Turn off all controls before unplugging.» Use extra care when cleaning on stairs.» Do not use to pick up flammable or combustible liquids, such as petrol, oruse in areas where they may be present.» Do not pick up toxic material (chlorine bleach, ammonia, drain cleaner, etc.)» Do not use appliance in an enclosed space filled with vapors given off byoil base paint, some mothproofing substances, flammable dust, or otherexplosive or toxic vapors.» Do not pick up hard or sharp objects such as glass, nails, screws, coins, etc.» Keep appliance on a level surface.» Do not carry appliance while in use.» Unplug before attaching the TurboBrush tool.» Do not pick up anything that is burning or smoking, such as cigarettes,matches, or hot ashes.» If your appliance is fitted with a nonrewireable BS 1363 plug it must notbe used unless a 13 amp (ASTA approved to BS 1362) fuse is fitted in thecarrier contained in the plug. Spares may be obtained from your BISSELLsupplier. If for any reason the plug is cut off, it must be disposed of, as it isan electric shock hazard should it be inserted into a mains socket.» Do not expose to rain. Store indoors.» Always install float before any wet pick-up operation.» Plastic film can be dangerous. To avoid danger of suffocation, keep awayfrom children.» Have servicing performed by a qualified repair person using only identicalreplacement parts. This will ensure that the safety of the product ismaintained.SAVE THESE INSTRUCTIONSFOR OPERATION ON A 220-240 VOLT A.C. 50-60 HZ POWER SUPPLY ONLY.This model is for household use only.Caution.Refer to instruction manual.This symbol means to recycle.Recycling to help the environment. Dispose of packaging at the applicable recycling collection point. This symbol means torecycle. Do not mix packaging with general household waste.This symbol on the product and/or accompanying documents means that used electrical and electronic products should notbe mixed with general household waste. For proper treatment, recovery and recycling, please take this product to designatedcollection points. Please contact your local authority for further details of your nearest designated collection point.2www.BISSELL.com
Quick Start GuideAssemblyWARNINGDo not plug in your deep cleaner until you are familiar with all instructionsand operating procedures.Your deep cleanercomes in foureasy-to-assemblecomponents andan accessory bag. Base Upper Handle Clean Water Tank Carry Handle1A Phillips screwdriver isrequired for Assembly inStep 3.2First, insert the(aluminum)Upper Handleat the top of thebase until youhear a “click”.Do NOT putthe clean tankon the machineuntil Step 5.click34Next, align the carry handle with the slotson either side of the base (behind thepower switch and cleaning mode switch).The carry handle will “click” into place.5SideViewUse a Philips screwdriverto secure the screw (foundtaped to upper handle)into the carry handle.Wrap the cord aroundthe carry handle and QuickRelease Cord Wrap hook.At the bottom of theupper handle, align theclean water tank withthe grooves and slidethe tank into place.www.BISSELL.com3
Thanks for buying a BISSELL carpet cleaner!We love to clean and we’re excited to share one of our innovative productswith you. We want to make sure your carpet cleaner works as well as itdoes today for years to come, so this guide has tips on using (pages 7-12),maintaining (pages 13-17), and if there’s a problem, troubleshooting (page 18).In just a few simple assembly steps, you’ll be ready to deep clean. Flip to theQuick Start Guide on page 3 and let’s get started!Package Contents1.2.5.7.43.1. Upper Handle2. 1 Screw attached toUpper Handle3. Base with Dirty Water Tank4. Clean Water Tank5. Carry Handle6. Trial Size BISSELL Formulas (3)7. Accessory bag & hose8. Tough Stain Tool9. 2-in-1 Pet Upholstery Tool10. Nozzle Clean Out Tool4.6.8.9.10.NOTE: Standard accessoriesmay vary by model. To identifywhat should be included withyour purchase, please referto the “Carton Contents” listlocated on the carton top flap.Safety Instructions . . . . . . . . . . . . . . 2Hose, Tools & CleanShot . . . . 10-12Quick Start Guide . . . . . . . . . . . . . . . 3Maintenance & Care . . . . . . . . . 13-17Product View . . . . . . . . . . . . . . . . . . . 5Troubleshooting . . . . . . . . . . . . . . . 18Cleaning Formulas . . . . . . . . . . . . . . 6Guarantee . . . . . . . . . . . . . . . . . . . . 20Operations . . . . . . . . . . . . . . . . . . . . 7-9Service . . . . . . . . . . . . . . . . . . . . . . . 20www.BISSELL.com
Getting to Know Your Deep CleanerIn-UseCord ClipUpperHandleCarryHandleCleaning ModeSwitchSpray TriggerRubberTabBeltAccess DoorFormula CapCleanShot ButtonQuickRelease Cord WrapClean Water Tank(3.7 Liter Capacity)ReclinePedalEdgeSweep BrushesPowerButtonFloatStackDirty Water TankFootBelt AccessNozzleBelt/BrushAccess Platewww.BISSELL.com5
Cleaning FormulasWARNINGTo reduce the risk of fire and electric shock due to internal component damage, use onlyBISSELL cleaning fluids intended for use with the deep cleaner.Keep plenty of genuine BISSELL formulaon hand so you can clean whenever it fitsyour schedule.Always use genuine BISSELL deepcleaning formulas. Non-BISSELL cleaningformulas may harm the machine and mayvoid the guarantee.PRETREATPRE TREAT SPOTS AND STAINSTO IMPROVE CARPET CLEANINGPERFORMANCEStain PreTreatPet Stain PreTreatPretreat topenetrateand loosentough stainsPretreat to helpremove toughpet stainsand odors2X* CONCENTRATED CLEANING FORMULASWASH &REMOVEWASH & PROTECTProfessionalStain & OdourPet Stain &OdourStain & Odour OxyProfessionalstrength toremove extratough stainsand odoursIncludesScotchgard ProtectorRemoves toughpet stainsand containspatentedodour removaltechnologyIncludesScotchgard ProtectorRemovestough stainsand odoursIncludesScotchgard ProtectorPermanentlyremovestough stainslike red wine,coffee, tea,cola and grapejuice withActive OxygenTechnologyWASH &SHINEWASH & REFRESHFebreze Febreze Blossom & CottonFreshBreezePowerfulcleaningwith arefreshingspring scentPowerfulcleaningwith arefreshingclean scenNaturalOrangeHard FloorCleanerPowerfulcleaningwith arefreshingnaturalorangescentRemoves dirtand grimefrom sealedhard floorsurfaces;leaves anatural shineONLY BISSELL Wash & Protect formulas protect from future stains with Scotchgard Protector.Scotchgard is a trademark of 3M .*60 mL of 2X concentrated formula is equivalent to 120 mL of non-concentrated formula.Tips Before Carpet Cleaning If cleaning an entire room, consider moving your furniture to another area. Remove loose dirt and impediments. Pre-treat stains with BISSELL PreTreat to improve performance on toughstains and ground-in dirt.6www.BISSELL.com
Filling Your Clean Water Tank:2X Concentrated Formula12Clean Water Tank(3.7 Litre)Dirty Water TankThe clean water tank is at thetop of the machine.34Unscrew the cap from the clean water tank. Add hottap water to the water fill line. Next, reference the chartbelow for formula amounts to add to the tank. Twistcap back into place.FORMULA FILLINGINSTRUCTIONSBISSELL 2XConcentrated FormulasLift the clean water tankstraight up to remove fromthe machine.DEEP CLEAN MODEFill water to the WaterFill Line, then add 74 mLof formula.At the bottom of the upperhandle, align the clean watertank with the grooves andslide the tank into place.EXPRESS CLEAN MODEFill water to the WaterFill Line, then add 37 mLof formula.NOTE: Fill with hot (140 F/60 C MAX) tap water and add the appropriateBISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER ORTANK IN MICROWAVE. Do not substitute BISSELL Cleaning Formula with otherhousehold cleaning products.NOTICE: Do not over wet carpet. Be careful not to run over loose objects oredges of area rugs. Stalling the brush may result in premature belt failure.Always use genuine BISSELL deep cleaning formulas. Non-BISSELLcleaning solutions may harm the machine and may void the guarantee.www.BISSELL.com7
Cleaning Your Carpet123Selectcleaningmode:Deep CleanDelivers a deepclean to yourcarpet.Plug into a properlyearthed outlet.Express CleanProvides a lighterclean with about1 hour of dry time.Press the power buttonto turn the machine on.To recline your machinefor use, press the reclinepedal with your foot.4Deep Clean Mode:Express Clean Mode:1. Press the spray trigger to apply solution while making 2 slow wet passes - 1forward and 1 back.1. Press the spray trigger to apply solution while making 2 wet passes - 1 forward and 1 back.2. Release the trigger.2. Release the trigger.3. Make 2 slow dry passes - 1 forwardand 1 back, to suck up the dirty solution. (Do not hold down the trigger forthis step.)3. Make 2 dry passes - 1 forward, 1 backto suck up the dirty solution. (Do nothold down the trigger for this step.)NOTE: For best cleaning performance,clean with your machine in Deep CleanMode.NOTE: In Express Clean Mode, thedirty tank will not get as full as whencleaning with Deep Clean Mode.NOTICE: To prevent damage to Berber carpets, avoid repeated strokes inthe same area.8www.BISSELL.com
Bare Floor Cleaning**Select models onlyWARNINGWARNING: To reduce the risk of fire and electric shock when cleaning a hard floor, theBISSELL bare floor tool must be used and is only to be used with BISSELL Wash & ShineHard Floor Cleaner formula intended for use with this appliance.NOTE: The bare floor tool that is compatible with the ProHeat 2X Revolutionmay not be included. It is available for purchase by contacting our team byphone or visting us online at BISSELL.com.21With the machine unplugged,attach the bare floor tool tothe bottom of the machineby lining the tool to the edgeof the nozzle. Rotate downuntil it clicks into place.Follow filling instructionson page 10 or 11 and switchcleaning mode to ExpressClean.3Plug into a properlygrounded outlet and pressthe power button.When finished, unplug themachine and remove thebare floor tool by rotatingthe tool up to unhookfrom the nozzle.Clean by pressing thetrigger for 1 wet passforward, 1 wet pass back,and then release thetrigger and make 1 dry passforward, 1 dry pass back.Rinse and let dry beforestoring. Refer to page 13for emptying the dirtywater tank. Refer topage 14 for cleaning yourmachine before storing.Area Rug CleaningImportant! Please check manufacturer’s tag before cleaning area rugs forany specialized cleaning instructions. We do not recommend deep cleaningdelicate, silk, wool, antique or area rugs without a manufacturer’s tag.Regularly clean your high-traffic area rugs in Express Clean Mode: Check the manufacturer’s tag. Select Express Clean Mode. When cleaning area rugs, place the rug on a sealed surface to test for colorfastnessin an inconspicuous area. Your cleaner should not be used on unsealed surfaces. Important: Keep the foot of the deep cleaner perpendicular to the rug’s edge witheach cleaning pass to prevent damage.www.BISSELL.com9
Cleaning with Hose & Tool1— Keep hair, loose clothing, fingers, and all partsof body away from openings and moving parts.Brushroll continues to rotate when in the uprightposition.Lift the accessoryhose door on topof foot on the frontof the machine. Thedoor flips toward themachine to open.2Insert the hose andsnap into place.Be sure the coloredhose release clipis facing out, awayfrom machine.— Brushroll continues to turn while product isturned on and handle is in upright position. To avoiddamage to carpet, rugs, furniture and flooring, avoidtipping cleaner or setting it on furniture, fringedarea rugs, or carpeted stairs during tool use.— The brushroll remains on while cleaning with thehose and tool. Do not allow cleaner to sit in onelocation for an extended period of time, as damageto floor can result.4Press the spray trigger button to spraythe soiled area, then slowly move tool backand forth over the area.Release the trigger to suck up the dirtysolution. Work in small sections until the areais clean.3Attach the tool to the end of the hose.(Tools may vary by model.) Press thepower button to turn machine on.When finished cleaning, turn the machine onto suction up warm clean water to rinse theinside of the hose and tool. Detach the hoseand tool and close the accessory hose door.Let the hose and tool air dry before storing.NOTE: If using the Deep Reach Tool (select models only) or Pet Stain Tool(select models only) be sure the needles of the tool are pressed down into thecarpet so the spray gets into the carpet fibers.10www.BISSELL.com
Cleaning with CleanShot 1Press the CleanShot button with your foot.The window of the button will be green andshow an “I” symbol when it is on.2Spray will continue until you turn itoff. To turn CleanShot off, press thebutton with your foot. The window ofthe button will be red and show an “O”symbol when it is off.Completely cover the stain with CleanShot spray. Allow the stain to soak. Toextract, maneuver the foot of the machine over the stain to brush and remove.www.BISSELL.com11
NEW! 2-in-1 Pet Upholstery Tool*Make sure your clean tank has water & formula to use the tool in wet mode.21Dry Mode(switch up)Follow hose plug-in instructions fromsteps 1 & 2 on page 14.DrySuctionChannelAttach the tool and select dry modeto first pick up dry debris and pethair. The suction will be at the lowerpart of the tool, near the dry cup.DRY MODE NOTE: Use a “raking” motion to clean. Start with the tool farthestaway and rake in small increments as you bring the tool toward you. The rubbernubs will help attract hair to the suction channel.3Empty the cup whenit fills with hair anddebris.46Take off the cupto empty hairand debris.5Turn off the machine.Hold the cup and twistcounterclockwise. Line upthe arrow with the unlocksymbol and remove.7WetSuctionChannelWet Mode(switchdown)To Deep Clean, move theswitch to wet mode. Pressthe trigger to spray yourwater and formula; usethe top of the nozzle toextract stains and odors.Remove hairthat may wraparound the filter.To reattach the cup, lineup the cup to the toolindents, and rotate clockwise. The arrow will lineup with the locked iconwhen secured.89To remove any hair ortrapped debris from thenozzle, first turn off themachine. Pull the nozzletab away from the tool toremove and rinse underrunning water.Replace the tool by liningup the nozzle edge andsnap into place. Beforestoring, make sure all hairis removed from the drycup and nozzle has beenrinsed under runningwater.WET MODE NOTE: Start from the area farthest away. Hold the trigger down, andpull the tool toward you. Keep the tool in contact with the surface as you pull. Youwill see extraction through the nozzle.12www.BISSELL.com
Empty Dirty Water TankWARNINGTo reduce the risk of fire, electric shock or injury, turn power OFF and disconnect plug fromelectrical outlet before performing maintenance or troubleshooting.12To release dirty watertank, press down on thecolored tank handle.Tilt the tank slightlytoward you.4For quick empty:Pull the rubber taband tilt to pour.(Located at the cornerof the top of the tank.)When closing therubber tab, makesure all edges aresealed tight.For final clean andrinse: Unscrew the ringat the bottom of tank.Gently remove thefloat stack, rinse,and clean.Once clean, return floatstack into the tank bylining up the arrowsso they point at eachother. This is the onlyway the float stack willfit into the tank.With the arrowsaligned, the float stackshould lock into place.Return the ring andtwist to lock. Watermay leak if the ring isnot fully tightened.3Grab the handle and tankwith both hands and pullthe dirty water tank upand away to remove.5Clean the red filterbelow the dirtytank by wiping offany remaining dirtor debris.6To return the dirtytank: Angle the tankand insert bottomfirst. Then tilt thetank toward themachine and pushthe top in until itclicks into place.Did You Know?The Float Stackis what preventsyour dirtytank fromoverflowing.www.BISSELL.com13
Cleaning Machine After UseWARNINGTo reduce the risk of electric shock, turn power switch off and disconnect plug fromelectrical outlet before performing maintenance or troubleshooting checks.First, fill the clean watertank with warm tap waterand then empty it all torinse. Then fill again withwarm tap water and returnthe tank to the machine.Twist cap back on tightly.To flush and rinse themachine: Turn the machineon and press the trigger for15 seconds while makingback and forth passes on asection of carpet.Finally, release the triggerand extract the water.See page 13 to clean thedirty tank from the waterthat was just extracted.Empty the clean water tankand let dry before storing.Wipe your machine’sexterior with a soft cloth.Store machine in aprotected dry area.NOTICE: To reduce the risk of a leaking condition, do not store unit wherefreezing may occur. Damage to internal components may result.14www.BISSELL.com
Brush Roll & Nozzle CareWARNINGTo reduce the risk of electric shock, turn power switch off and disconnect plug fromelectrical outlet before performing maintenance or troubleshooting checks.NOTE: Be sure to clean the brush rolls and nozzle before storing your machine.Follow these steps if your nozzle becomes clogged with hair or debris.21Turn off and unplugthe machine from thegrounded outlet.357clickPull forward thenozzle wire onthe front of thebrush roll coverfor release.At this point, thenozzle and brushroll cover canbe rinsed underrunning water andthe nozzle cleanout tool can beinserted to uncloghair or debris.46Remove the nozzlefrom the foot:scoop and grip theAccessory HoseDoor. Pull up toremove the nozzle.To reveal thebrush rolls.Press on thetwo releasebuttons and liftstrai
cleaning solutions may harm the machine and may void the guarantee. NOTE: Fill with hot (140 F/60 C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. Do not substitute BISSELL Cleaning Formula with other household clea
