WIXLIB

NAVAL ENGINEERING COMPUTERAIDED DESIGN STANDARDSCOMDTINST M9085.1CNOVEMBER 2011

Page Intentionally Left Blank

CommandantUnited States Coast Guard2100 Second Street S.W.Stop 7901Washington, DC 20593-7901Staff Symbol: CG-4Phone: (202) 475-3655COMDTINST 9085.1C12 NOV 2011COMMANDANT INSTRUCTION M9085.1CSubj:NAVAL ENGINEERING COMPUTER AIDED DESIGN STANDARDS1. PURPOSE. This Manual provides direction for Coast Guard activities and commercialcontractors to develop Coast Guard drawings for Hull, Mechanical, Electrical (HM & E),Ordnance and Electronic systems and equipment for Coast Guard vessels.2. ACTION. All Coast Guard unit commanders, commanding officers, officers-in-charge,deputy/assistant commandants, and chiefs of headquarters staff elements shall complywith the provisions of this Manual. Internet release is authorized.3. DIRECTIVES AFFECTED. COMDTINST 9085.1B is canceled.4. BACKGROUND.a. Commandant (CG-4) has adopted AutoCAD 2009 as the standardized computeraided design system for Coast Guard vessels.b. AutoCAD systems have been installed at all major Coast Guard maintenance andlogistics support activities.5. SUMMARY OF CHANGES. Changes made within this revision are primarily to beutilizing current technology more efficiently.a. Whole document: Modified all references to AutoCAD 2002 to AutoCAD 2009.b. Chapter 2: Revised Signature Authority criteria to conform to the CG’smodernization.c. Chapter 4: Revised Storage and Transmission Media for Electronic Files to remove“Floppy Disk.”DISTRIBUTION – SDL No. NON-STANDARD DISTRIBUTION:xxxxxxz

d. Chapter 5: Modified Dimensioning criteria to require them to be in Paper Space.Added section “Computer Oriented Wiring Diagrams (COED).” Added section“Proofing and Performing Drawing Check-Off.”e. Chapter 6: Revised Drawing Sheet and Border Template requirements to matchcurrent standards and AutoCAD 2009 capabilities. Added requirement of multi-sheetdrawings to be in one electronic file utilizing the ‘Layout Tabs’ feature in AutoCAD2009.6. POLICY.a. All drawings shall be delivered to the Coast Guard in AutoCAD 2009 compatible(.dwg) file format and in accordance with Naval Engineering Manual M9000.6(series) to allow for the life-cycle drawing maintenance.b. Chief of Surface Forces Logistics Center (SFLC), Engineering Service Division(ESD), Technical Information Management Branch, (TIMB), is designated as thesystems manager for all AutoCAD drawing issues relating to Coast Guard vesseldrawings.c. The CAD standard requirements identified in this instruction apply to all newdrawings and for all revisions to existing drawings.d. For Coast Guard units and commands, this Manual does not constitute authority topurchase the hardware or software required to comply with this Manual. Suchprocurements must be conducted in accordance with current Coast Guard directivesfor the purchase of computer hardware and software.7. CONTENTS. This Manual consists of written standards for use in the development ofCAD drawings.8. CHANGES. Recommendations for future changes to this Manual shall be submitted to:Commanding OfficerATTN: ESD-TECH INFO MGMT BranchSurface Forces Logistics Center2401 Hawkins Point Rd. Stop 25Baltimore, MD 21226-17979. RECORDS. Records created by compliance with the requirements of this Manual,including those promulgated in Naval Engineering Manual, COMDTINST M9000.6(series), will be maintained in accordance with Information and Life Cycle ManagementManual , COMDTINST M5212.12 (series).10. ENVIRONMENTAL ASPECT AND IMPACT CONSIDERATIONS. This action is not2

expected to result in any significant adverse environmental impacts as described in theNational Environmental Policy Act of 1969 (NEPA). The proposed action has beenreviewed by the USCG and has determined this action to be categorically excluded fromfurther environmental documentation under current USCG Categorical Exclusion # 33, inaccordance with National Environmental Policy Act Implementing Procedures and Policyfor Considering Environmental Impacts, COMDTINST M16475.1 (series), Figure 2-1.11. FORMS AND REPORTS. None.R. J. RÁBAGO /s/Rear Admiral, U. S. Coast GuardAssistant Commandant for Engineering and Logistics3

COMDTINST M9085.1CTABLE OF CONTENTSCHAPTER - 1 INTRODUCTIONA. Standards and RequirementsB. Additional Standards and RequirementsC. List of Specifications and Standards1-11-11-11-1CHAPTER - 22-1DRAWING SIGNATURE AUTHORITYA. Drawing Signature AuthorityCHAPTER - 32-1TITLE BLOCK NUMBERING CONVENTIONA. Drawing Numbers and Title Block Numbering ConventionCHAPTER - 4ELECTRONIC FILE LABELING CONVENTIONS ANDSTORAGE/TRANSMISSION MEDIAA. Electronic File Naming Convention for Drawing FilesB. Storage and Transmission Media for Electronic FilesCHAPTER - 5A.B.C.D.E.F.G.H.I.J.K.L.M.N.O.P.GENERAL REQUIREMENTSAuthorized SoftwareDrawings Prepared In Data Processing Systems (Text and Graphics Processing)Sheet Sub-TitlesPaper SpaceDrawing Layering ConventionBlocks and ShapesDrawing Zone RequirementsExternal ReferencesSolid Models, 3D Models and Renderings/ShadingDimensionsText StylesLine TypesColor UsageRevision Symbol BlockComputer Oriented Wiring Diagram (COED)Proofing and Performing Preliminary Drawing check-offCHAPTER - 6DRAWING SHEET & BORDER TEMPLATEA. Drawing Sheet Format and SizesB. Standardized Border TemplatesC. Mandatory and Conditional Blocks or -45-45-45-45-45-55-55-66-16-16-16-1

COMDTINST M9085.1CCHAPTER - 7PLOTTING INSTRUCTIONSA. Normal Layer Line Width and VisibilityB. Special Plotting InstructionsCHAPTER - 8A.B.C.D.E.7-17-17-1GENERAL DRAWING PRACTICESDrawing CreationDrawing RevisionsRevision Procedures for Special SituationsSuperseding a DrawingCancelling a Drawing8-18-18-18-38-38-3APPENDIX – A INSTRUCTIONS FOR COMPLETING ATTRIBUTE BLOCKS A-1A.B.C.D.E.Coast Guard Title with USCG Approval BlockSupplemental Drawing Number BlockCoast Guard Title Block, Continuation SheetCommand or Contractor Approval Signature BlockRevision Triangle BlockA-1A-1A-1A-2A-2LIST OF FIGURESFigure 1Figure 2Figure 3Figure 4Figure 5Figure 6Figure 7Figure 8Figure 9Figure 10Figure 11Figure 12Figure 13Figure 14Figure 15Figure 16Drawing Zones for Addendum SheetsCoast Guard Title with USCG Approval Block (SHEET 1)Coast Guard Title Block for Continuation Sheet (SHEET 2 &SUBSEQUENT)Command or Contractor Approval Signature Block (CCBLK)Supplemental Drawing Number Blocks (SUPDWGBLK)Reference Plans Table (REFPLBLK)Revision Triangle Block (REVTRIBLK)Materials List Table (MATBLK)Linear Reduction Scale Block 1” 1’-0”Weight Control Table (WGTBLK)Revision History Table (REVHISBLK)Sheet Revision Status Table (SREVBLK)Applicability Table (APPBLK)Special Notations Table (SNOTEBLK)Special Plotting Instructions Block (PLTBLK)Scientific Technical Information (STINFO) -76-8

COMDTINST M9085.1CCHAPTER - 1A.INTRODUCTIONStandards and Requirements1. This Manual sets forth the minimum standards that shall be followed in thedevelopment of all CAD drawings created for Coast Guard (CG) vessels.2. These standards are subject to change and will require periodic updates to takeadvantage of technological advancements. Recommended changes shall beforwarded in writing to Commanding Officer (SFLC, ESD, Technical InformationManagement Branch, 2401 Hawkins Point Road, Baltimore, MD 21226-1797).B.Additional Standards and Requirements1. These standards are not stand-alone requirements; they are intended to augmentexisting commercial and military standards that are commonly used in drawingdevelopment within Naval Engineering programs. Except as noted in this Manual,the following standards shall be considered an integral part of this Manual.2. In the event of a conflict between the text of this document and the references citedherein, the text of this document shall take precedence. Nothing in this document,however, supersedes applicable laws and regulations unless a specific exemption hasbeen obtained.C.List of Specifications and Standards1. COMDTINST M9000.6USCG Naval Engineering Manual, Chapter 0852. COMDTINST M5260.6Management of Scientific and TechnicalInformation3. ANSI/ASME Y14.l-2005Decimal Inch Drawing Sheet Size and Format4. ANSI/ASME Y14.2-2005Line Conventions and Lettering5. ANSI/ASME Y14.3-2003Multiview and Sectional View Drawings6. ANSI/ASME Y14.5-2009Dimensions and Tolerancing7. ANSI/ASME Y14.3-2008Associated Lists8. ANSI/ASME Y14.35MRevision of Engineering Drawings and AssociatedDocuments9. ANSI/ASME Y14.38Abbreviations & Acronyms for Use on Drawingsand related Documents1-1

COMDTINST M9085.1C10. ANSI/ASME Y14.100Engineering Drawing Practices11. ANSI/ASME Y32.2.4Graphic Symbols for Heating, Ventilating and AirConditioning12. ASTM F856Standard Practice for Mechanical SymbolsShipboard-Heating, Ventilation And AirConditioning (HVAC)13. AWS A2.4Standard Symbols for Welding, Brazing andNondestructive Examination14. AWS A3.0Standard Welding Terms and Definitions: IncludingTerms for Adhesive Bonding, Brazing, Soldering,Thermal Cutting, and Thermal Spraying15. ISO 1219-1Graphic Symbols for Fluid Power16. ISO/IEC 10149:1995Information Technology – Data Interchange on read– only 120 mm optical data disks (CD-ROM)17. IEEE-315Graphic Symbols for Electrical and ElectronicsDiagrams18. IEEE-91-1984Graphic Symbols for Logic Functions19. ANSI-Y32.9-1972Graphic Symbols for Electrical Wiring and LayoutDiagrams Used in Architecture and BuildingConstruction20. MIL-D-23140DDrawings, Installation Control, for ElectronicEquipment21. MIL-STD-31000Technical Data Packages22. MIL-STD-25Ship Structural Symbols for Use on Ship Drawings(See Note)23. MIL-HDBK-290(1)Standard Electrical Symbol List24. ISO 14617-1:2005Graphical symbols for diagrams Part 1: Generalinformation and indexes25. ISO 14617-2:2002Graphical symbols for diagrams - Part 2: Symbolshaving general application1-2

COMDTINST M9085.1C26. ISO 14617-3:2002Graphical Symbols for Diagrams - Part 3:Connections and related devices27. ISO 14617-4:2002Graphical Symbols for Diagrams - Part 4: Actuatorsand related devices28. ISO 14617-5:2002Graphical Symbols for Diagrams - Part 5:Measurement and control devices29. ISO 14617-6:2002Graphical Symbols for Diagrams - Part 6:Measurement and control functions30. ISO 14617-7:2002Graphical Symbols for Diagrams - Part 7: Basicmechanical components31. ISO 14617-8:2002Graphical Symbols for Diagrams - Part 8: Valvesand dampers32. ISO 14617-9:2002Graphical Symbols for Diagrams - Part 9: Pumps,compressors and fans33. ISO 14617-10:2002Graphical Symbols for Diagrams - Part 10: Fluidpower converters34. ISO 14617-11:2002Graphical Symbols for Diagrams - Part 11: Devicesfor heat transfer and heat engines35. ISO 14617-12:2002Graphical Symbols for Diagrams - Part 12: Devicesfor separating, purification and mixing36. ISO 14617-15:2002Graphical Symbols for Diagrams - Part 15:Installation diagrams and network mapsNote: Ship drawings shall comply with MIL-STD-25 except that steel symbol designations mayconform to the current American Institute of Steel Construction (AISC) “Manual of SteelConstruction.”1-3