Transcription
Alliance 815/835HR TREADMILLOWNER’S MANUALAlliance Fitness TreadmillsManufactured in the USA by:KEYS Fitness Products, LPP.O. Box 551239Dallas, Texas 75239www.keysfitness.com
TABLE OF CONTENTSPAGETable of Contents2Important Safety Information3Before You Start4Warm Up Exercises5Unpacking and Moving Instructions6Power Requirements7Console Functions and Descriptions8, 9, 10Program and Operating Instructions11, 12, 13Program Descriptions and Profiles14Belt Adjustments and Tension15Maintenance Instructions16Troubleshooting Guide17Parts and Diagrams18,19,20Warranty Registration (Mail In Form)221
Important Safety InformationNING!1) WARNING: Before using this treadmill or starting any exercise program, consult your physician. This isespecially important for persons over the age of 35 and/or persons with pre-existing health problems. Themanufacturer or distributor assumes no responsibility for personal injury or property damage sustained by or throughthe use of this product.2) WARNING: To reduce the risk of electrical shock, burns, fire, or other possible injuries to the user, it is importantto review this manual and the following precautions before operation.SAFETY PRECAUTIONS AND TIPS It is the owner’s responsibility to ensure that all users of this treadmill have read the Owner’s Manual and are familiarwith warnings and safety precautions. This treadmill has a user maximum capacity of 275 pounds. The treadmill should only be used on a level surface and is intended for indoor use only. The treadmill should notbe placed in a garage, patio, or near water and should never be used while you are wet. We recommends atreadmill mat be placed under the treadmill to protect floor or carpet and for easier cleaning. Follow safety information in regards to plugging in your treadmill. Keep the power cord away from the incline wheelsand do not run the power cord underneath your treadmill. Do not operate the treadmill with a damaged or frayedpower cord. Wear comfortable, good-quality walking or running shoes and appropriate clothing. Do not use the treadmill withbare feet, sandals, socks or stockings. Always straddle the belt and allow it to start moving before stepping onto the belt. Hold on to handrails when adjusting speed, incline, or other controls. Always examine your treadmill before using to ensure all parts are in working order. Allow the belt to fully stop before dismounting. Pets should be never be allowed near or on the treadmill. Do not leave children unsupervised near or on the treadmill. Never operate the treadmill where oxygen is being administered, or where aerosol products are being used. Never insert any object or body parts into any opening. For safety and to prevent damage to your treadmill, no more than one person should use the treadmill at a time. Always unplug the treadmill before cleaning and/or servicing. Service to your treadmill should only be performed byan authorized service representative, unless authorized and/or instructed by the manufacturer. Failure to followthese instructions will void the treadmill warranty. Never leave the treadmill unattended while it is running.3
Before You StartThank you for purchasing an Alliance treadmill! This quality product you have chosenwas designed to meets your needs for cardiovascular exercise. Before you start, please read the Owner’s Manual and become familiar with theoperation of your new treadmill. Remember to take the time to perform the stretching exercisesprovided to avoid injury. Do not stand on the walking belt while pressing the Power or Start/Stop button. Always adjust the speed of the treadmill in small increments as this treadmill is capableof high speeds. If you are taking medication, consult your physician to see if the medication will affectyour exercise heart rate. If you have heart problems, you are not active, and/or are over the age of 50 years, donot use the pre-set treadmill programs or start an exercise program without firstcontacting and receiving approval from your physician. To avoid the risk of electrical shock, always keep the console dry. Do not spill liquidson the console. The manufacturer recommends a sealed water bottle for beveragesconsumed while using the treadmill. Please review the following drawing below to familiarize yourself with the listedparts. This manual covers several treadmills, so the one pictured below may notbe identical to your particular model.4
Warm Up ExercisesNING!WARM UP FIRST !Warming up prepares the body for exercise by increasing circulation, supplying moreoxygen to the muscles and raising body temperature. Begin each workout with 5 to 10minutes of stretching and light exercise to warm up. The drawings on this page showseveral forms of basic stretching you may perform before your workouts. Again, consult aphysician before starting this or any other exercise program.15 Seconds for each25 Seconds30 Seconds20 Seconds25 Seconds each leg20 Seconds20 Seconds25 Seconds each leg5 Seconds X 3 times5 Times520 Seconds20 Seconds30 Seconds20 Seconds15 Seconds
Unpacking and Moving InstructionsNo Assembly Required!Alliance treadmills are shipped in one piece and fully assembled. After opening the box, removeany packing materials from the treadmill. Do not throw away any packing materials until the unitis working properly. The treadmill box contains a package that includes the Owners Manual, aRED SAFETY KEY, and a belt adjustment tool. The 835HR will also contain the heart rate cheststrap. The treadmill will not operate without the Safety Key.MovingPlace the base on a clean, level surface. Make sure the electrical cord will easily reach anelectrical outlet. CAUTION ! TO AVOID THE RISK OF INJURY, NEVER ATTEMPT TO MOVETHE TREADMILL WHILE IT IS IN THE UNFOLDED OPERATING POSITON. TO REDUCE THEPOSSIBILITY OF INJURY WHILE LIFTING, BEND YOUR LEGS AND KEEP YOUR BACKSTRAIGHT. AS YOU RAISE THE TREADMILL, LIFT USING YOUR LEGS, NOT YOUR BACK.IN ORDER TO RAISE OR LOWER THE TREADMILL SAFELY, YOU MUST BE ABLE TO LIFT45 POUNDS (20KG). IT IS SUGGESTED YOU ALWAYS USE THE AID OF A SECONDPERSON WHEN MOVING THE TREADMILL.With the treadmill in the folded locked position (safety latch is engaged), grasp the handrails andplace one foot on base as shown in the illustration below. Next, with a firm grasp on handrails,place one foot on the center of the base crossbar and carefully tilt the treadmill back until it rollsfreely on the wheels. Using extreme caution, move the treadmill to the desired location. To setthe treadmill down, place one foot on the center of the base crossbar and carefully lower treadmillonto base in resting position. Do not attempt to move the treadmill over an uneven or roughsurface.6
Power RequirementsWARNING!IMPROPER CONNECTION OF THE EQUIPMENT GROUNDING CONNECTOR CAN RESULTIN A RISK OF AN ELECTRIC SHOCK. CHECK WITH A QUALIFIED ELECTRICIAN ORSERVICE MAN IF YOU ARE IN DOUBT AS TO WHETHER THE PRODUCT IS PROPERLYGROUNDED. DO NOT MODIFY THE PLUG PROVIDED WITH THE PRODUCT, IF IT WILLNOT FIT THE OUTLET, HAVE A PROPER OUTLET INSTALLED BY A QUALIFIEDELECTRICIAN.This treadmill can be seriously damaged by sudden voltage changes in your home’s electrical power. Voltagespikes, surges, and noise interference can result from weather conditions or from other appliances being turned on oroff. To reduce the possibility of treadmill damage, always use a surge protector (not included) with your treadmill.Surge protectors can be purchased at most hardware stores. The manufacturer recommends a single outlet surgeprotector with a UL 1449 rating as a Transient Voltage Surge Suppressor (TVSS) with a UL suppressed voltagerating of 400V or less and an electrical rating of 120VAC, 15 amps.This treadmill must be grounded to reduce the risk of electrical shock. Grounding provides a path of least resistancefor electric current, should the treadmill malfunction. This treadmill comes with an electrical cord having anequipment-grounding conductor and a grounding plug. Always plug the power cord into a surge protector, and plugthe surge protector into an appropriate outlet that is properly installed and grounded in accordance with all localcodes and ordinances.This product is for use on a nominal 120-volt circuit, and has a grounding plug that looks like the plug illustrated in thedrawing (1) below.7
Console Functions and DescriptionsSTART/STOP - This buttonstarts the treadmill beltmoving. There is a 4 secondcountdown built in as a safetyfeature to let you know thetreadmill belt is about to startmoving.Use the START/STOP buttonalso to stop your treadmillafter your workout. The beltwill gradually come to a stopafter pressing the button.PROGRAM BUTTONS - These buttons are used toaccess each of the three programs: Fat Burn, Cardio,and Warm Up. Each program has one preset program,and two additional custom programs in the P1 and P2mode. See the “Program and Operating Instructions” onpage 12.PAUSE - Press totemporarily pauseyour workoutwhile in use. Thetreadmill isdesigned with anautomatic poweroff feature after 5minutes in thepause mode.ENTER - Usethe Enter buttonwhile settingprogram time,speed, andincline options.See page 12 forcompleteONE TOUCH INCLINEBAR - Use to either increase ordecrease the incline. Eachnumber indicates percent ofgrade. Pressing one of thebuttons will gradually increaseor decrease the incline to thePOWER - Press to on. Allow6-8 seconds while theelectronics perform a selfcheck prior to pressing otherCONSOLE SAFETY KEY - Place the REDSafety Key here prior to turning power on.THE TREADMILL WILL NOT OPERATEWITHOUT THE SAFETY KEY ATTACHED.The safety key is equipped with a string andclip that will clip to your clothing. This is animportant safety feature that will automaticallyturn the power off if you should trip or fallwhile using the treadmill.INCLINE - Use to eitherincrease (UP arrow) ordecrease (DOWN arrow)the incline. These buttonsare also used whileprogramming INCLINE.ONE TOUCH SPEED BAR Use to either increase ordecrease the speed. Eachnumber indicates MPH.Pressing one of the buttons willgradually increase or decreasethe speed to the new setting.8SPEED - Use to eitherincrease (UP arrow) ordecrease (DOWN arrow)the speed. These buttonsare also used whileprogramming SPEED andTIME.
Console Functions and DescriptionsThere are five display windows on the control panel to provide feedback information.TIME WINDOW TIME: Indicates elapsed time after pressing start in minutes and seconds (0-99 minutes, 0-59seconds) INTERVAL TIME: Indicates countdown in seconds to the next interval starting at 5 seconds andcounting to 0 secondsSPEED WINDOW SPEED: Indicates MPH (miles per hour) or KMH (kilometer per hour) in .1 incrementsDISTANCE / CALORIES WINDOW DISTANCE: Indicates Miles or Kilometers traveled in .01 increments up to 9.99 and .1 incrementsstarting at 10.0 CALORIES: Indicates estimated calories used based on 150 lb. person at the indicated speed,incline, and time9
Console Functions and DescriptionsINCLINE WINDOW INCLINE: Indicates incline in percent of grade 0-12% in 1 increments PULSE (835HR Model Only): Indicates current heart rate HEART “ ” (835HR Model only): Indicates control panel is receiving a signal from heart ratetransmitter. Heart will blink on and off if receiving signal from Heart Rate Transmitter chest strap.CENTER BRICKYARD WINDOW Displays quarter mile track in Manual mode. Indicates position on track by a blink. In program mode,shows the change in speed profile across the interval range (1-10) and shows position with a blinkingaction.The 835HR will display the name of the program selected, showing on the left hand side of the window. The LAPcounter will appear in manual mode in the center of the window.SPEED & INCLINE “ONE-TOUCH” BUTTONS Easy One-Touch buttons for Speed and Incline have been added to the console. To increase ordecrease the speed, simply choose the desired setting (each number 2 through 8 represents Milesper Hour). To increase or decrease the amount of incline, simply choose the desired setting (eachnumber 2 through 8 represents percent grade).10
Program and Operating InstructionsQUICK START / MANUAL MODE Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). ATTACH THE RED SAFETY KEY TO CENTER OF CONSOLE. Stand on the treadmill and straddle belt. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data canbe entered. The TIME window will flash. Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt startsmoving. Speed or incline may be adjusted by using the appropriate UP (increase) or DOWN (decrease) buttons.Speed and Incline can also be adjusted using the “One Touch” buttons labeled 2 through 8, or by using the toggleswitches located on the handlebars. For speed and incline adjustments while using the treadmill, try theconvenient handlebar toggles switches. The left handlebar switch is for incline, while the right handlebar switchadjusts the speed. To end your workout, press START/STOP button. Belt will gradually slow to zero. To pause your workout, press PAUSE. The treadmill will automatically shut off after five (5) minutes. To re-start after pausing: Press the PAUSE button. WARNING: The treadmill belt will resume at the speed thetreadmill was moving before pausing. Countdown Time, Preset Speed and/or Incline: Time, Speed, and Incline may be preset prior to gettingstarted. After pressing the POWER button, the time window will blink. Use the SPEED UP or DOWN arrows toselect your workout time, then press the ENTER button located on the left hand side of the console below theprogram buttons. The SPEED/TIME window will now be flashing. Using the same or – arrows, select thespeed for your workout, then press ENTER. Now the INCLINE window will be flashing. Use the INCLINE or –arrows to set your workout incline, then press ENTER. To start, press the START/STOP button.11
Program and Operating InstructionsPROGRAM MODE Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). ATTACH THE RED SAFETY KEY TO THE CENTER OF THE CONSOLE. Stand on the treadmill and straddle belt. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data canbe entered. The TIME window will flash. There are three (3) pre-set programs on the 815 and 835HR. Both include Fat Burn, Cardio, and Warm Upprograms. The 835HR also includes a Heart Rate Control program (see the program profiles later in thismanual). Select the program by pressing the appropriate button. Press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly after the belt startsmoving. Each of the pre-set programs (6) can also be customized.particular model. Customizing programs in P1 and P2 Mode: Each pre-set program can be customized in the P1 or P2 mode.After making the program selection, the center window will read “OP.” ”OP” refers to “original program” and ispreset. Press the same program button once more, and the center window will read P1. The “P1” mode is nowaccessed. You can now program the Time, Speed, and Incline in P1 mode, which will save your enteredinformation for future use. The time window will blink. Use the SPEED UP or DOWN arrows to select yourworkout time, then press the ENTER button located on the left hand side of the console below the programbuttons. The SPEED window will now be flashing. Using the SPEED UP or DOWN arrows, select the speed foryour workout, then press the ENTER button. Now the INCLINE window will be flashing. Use the INCLINE UP orDOWN arrows to set your workout incline, then press the ENTER button. To start, press the START/STOPbutton. To access P2 mode, press the selected program button three times (once for OP, twice for P1, threetimes for P2). Follow the above procedure to customize. TO CHANGE A PREVIOUSLY PROGRAMMED P1, P2, or user program: Once you have programmed the P1or P2 modes, you will need to use the PAUSE button to change the program you previously entered. Forinstance, if P1 in Fat Burn has been programmed, to change to a new setting, press the Fat Burn button twice toaccess P1. Then press the PAUSE button to get the TIME window to flash. Follow the directions above tocontinue to change the program.12Follow the instructions below for your
Program and Operating InstructionsHeart Rate Control Instructions (835HR only)HEART RATE PROGRAM MODEThe Heart Rate program is designed to keep your heart rate a desired level of “beats per minute” by automaticallyadjusting the incline. For example, if you have programmed in a desired heart rate of 105 beats per minute and yourheart rate is only 95 beats per minute (you must be wearing Heart Rate Transmitter), the incline will automaticallyincrease to intensify the work load, and increase you heart rate to the 105 beats per minute you programmed.If your heart rate is above your programmed amount of beats per minute the incline will automatically decrease tolower your heart rate. You may at any time during the Heart Rate Program adjust/override the speed and or inclineby simply pressing the correct corresponding buttons. You may change your “Target Heart Rate” at ant time duringthe program by pressing the TARGET or TARGET – buttons. Plug into a standard wall outlet (110-Volt AC, 15-amp circuit). Attach Safety Key to console Place the Heart Rate transmitter strap across chest against the skin. Stand on the treadmill and straddle belt. Press POWER button. There will be an eight (8) second delay after pressing the POWER button before data canbe entered. The TIME window will flash. The “Heart” shape on the treadmill will be flashing if the Heart RateTransmitter is transmitting. Adjust the strap on the chest until the console is picking up a signal. For Quick Start, press START/STOP button. Belt will begin to move after 4 seconds. Step on belt slowly afterthe belt starts moving. Speed or incline may be adjusted by using the appropriate (increase) or – (decrease)buttons. Heart rate will read out in the Incline window. To select the Heart Rate Control program, press the “Heart Rate Control” button. The incline window will flash “125”, which is the default program target heart rate. Adjust Target Heart Rate to desired level with the TARGET or – buttons. Press START/STOP button, or continue instructions below to program Time, Speed and Incline. You can now program the Time, Speed, and Incline. The time window will blink. Use the SPEED/TIME or –arrows to select your workout time, then press the ENTER PROGRAM button. The SPEED/TIME window willnow be flashing. Using the same or – arrows, select the maximum speed for your workout, then press ENTERPROGRAM. Now the INCLINE window will be flashing. Use the INCLINE or – arrows to set your maximumworkout incline, then press ENTER PROGRAM. To start, press the START/STOP button.13
Program ProfilesThe FAT BURN program is designed to varytreadmill elevation while maintaining a constantwalking speed. Set the desired maximum speedand incline, and the treadmill will automaticallychange the incline to the set amount, alternatingin segments 2-3, 5-6, and 8-9.The CARDIO program is designed to varytreadmill speed while maintaining a constantincline. Set the desired maximum speed andincline, and the treadmill will automaticallychange the speed to the set amount, alternatingin each segment.EACH PROGRAM HAS 10 SEGMENTS. THELENGTH OF TIME FOR EACH SEGMENT ISBASED ON THE TIME LENGTH OF THEPROGRAM. IF YOU SET THE PROGRAM TO 30MINUTES, EACH SEGMENT IS 3 MINUTES LONG(TIME divided by 10 segments).YOU CAN ALSO CUSTOMIZE THE TIME, SPEED,AND INCLINE FOR EACH OF THESEPROGRAMS. SEE PAGE 12 FOR PROGRAMMINGTHE P1 AND P2 MODES.The WARM UP program is designed to graduallyincrease treadmill speed and incline (warm up) inthe first segment to the set maximum speed andincline. At the end of the program, the treadmillwill gradually decrease speed and incline to half ofthe maximum set (cool down) in segments 9-10.14
Belt Adjustment and TensionWARNING! Do not overtighten rollers! This will cause premature roller bearing failure!Belt adjustment and tension performs two functions: adjustment for tension and centering. Yournew treadmill comes pre-adjusted from the factory for tension and centering. Please follow theprocedures below if the belt shifts left or right or if the belt slips while walking:WALKING BELT HAS SHIFTING TO THE LEFT (Diagram 1)First, unplug the power cord from the surge protector. Using the hex key provided, turn the leftrear roller adjustment bolt ¼ turn in the clockwise direction. Plug the power cord back into thesurge protector and run the treadmill at 2.5 mph. You should see the belt start to correct itself,moving back towards the center. Repeat the above procedure until the walking belt is centered.It may be necessary to set walking belt tension once you have completed this procedure if the beltfeels like it is slipping while walking. Refer to below to the “Walking Belt Slipping” instructions.WALKING BELT HAS SHIFTING TO THE RIGHT (Diagram2)First, unplug the power cord from the surge protector. Usingthe hex key provided, turn the right rear roller adjustment bolt¼ turn in the clockwise direction. Plug the power cord backinto the surge protector and run the treadmill at 2.5 mph. Youshould see the belt start to correct itself, moving back towardsthe center. Repeat the above procedure until the walking beltis centered. It may be necessary to set walking belt tensiononce you have completed this procedure if the belt feels like itis slipping while walking. Refer to below to the “Walking BeltSlipping” instructions.WALKING BELT IS SLIPPING DURING USE (Diagram 3)First, unplug the power cord from the surge protector. Usingthe hex key provided, turn both left and right rear rolleradjustment bolts the same distance, usually a ¼ turn in theclockwise direction. Plug the power cord back into the surgeprotector and run the treadmill at 2.5 mph. You should nowwalk on the belt to determine if the belt is still slipping. Repeatthe above procedure until the walking belt is not slipping. Thetension should be just tight enough not to slip.15
Maintenance InstructionsWARNING! Before performing any maintenance to your treadmill, always unplugthe power cord from the surge protector.CLEANINGRoutine cleaning of your Alliance Fitness treadmill will extend the life of your treadmill. WARNING! To preventelectrical shock, be sure the power to the treadmill is OFF and the unit unplugged from the wall electrical outletbefore attempting any cleaning or maintenance.AFTER EACH WORKOUT: Wipe off the console and other treadmill surfaces with a clean, water dampened softcloth to remove excess perspiration. USE NO CHEMICALS.WEEKLY: Use of a treadmill mat is recommended for ease of cleaning. Dirt from your shoes contacts the belt andeventually makes it to underneath the treadmill. Vacuum underneath treadmill once a week.DECK LUBRICATIONThe walking belt has been pre-lubricated at the factory. However, it is recommended that the walking board bechecked periodically for lubrication to ensure optimal treadmill performance. Your treadmill should not have to belubricated usually within the first year or 500 hours of use. If you have questions, call us at (888) 340-0482.Every 30 days or 30 hours of operation, lift the sides of the walking belt and feel the top surface of the walking boardas far under as you can reach. If you feel signs of silicone, no further lubrication is required. If it feels dry to thetouch, follow the instructions below.Please use Lube ‘N Walk (can be purchased from your dealer or call the number on the front of the manual), or anon-petroleum based silicone such as “Napa 8300” (available at most stores).TO APPLY LUBRICANT TO THE WALKING BOARD1) Position the walking belt so that the seam is located on top and in the center of the center of the walking board.2) Insert the spray nozzle into the spray head of the lubricant can.3) While lifting the side of the walking belt, position the spray nozzle between the walking belt and the boardapproximately 6” from the front of the treadmill. Apply the silicone spray to the walking board, moving from the frontof the treadmill to the rear. Repeat this on the other side of the belt. Spray approximately 4 seconds on each side.4) Allow the silicone to ‘set’ for one minute before using the treadmill.16
Troubleshooting GuideTreadmill will not start.1) Is the RED Safety Key Attached to the Console?2) Make sure the power cord is plugged into a surge protector, the surge protector is plugged into aproperly grounded outlet, and the surge protector is turned on. (Refer to “Power Requirements”)3) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.Wait five minutes and then press the switch back in.4) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.If it has tripped, reset or have an electrician replace the breaker in home.5) Have an electrician check for inadequate voltage at the outlet.Treadmill looses power during use.1) Check the circuit breaker located on the front of the treadmill. If the switch protrudes, it has tripped.Wait five minutes and then press the switch back in.2) Check the house electrical breaker box and the circuit breaker for the room the treadmill is located in.If it has tripped, reset or have an electrician replace the breaker in home.3) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.Treadmill walking belt slows during use.1) Check to make sure the treadmill is securely plugged into an UL-listed surge protector, rated at 15amps, with a 14-guage cord of five feet or less and the surge protector is securely plugged into theoutlet.2) If treadmill still will not operate, please call Keys Technical Service at (888) 340-0482.Treadmill walking belt slips or is not centered on rear roller.1) Refer to “Belt Adjustment and Tension” section.2) Need help? Call Keys Technical Service at (888) 340-0482.Treadmill Error Messages.2)Your treadmill is equipped with a software package that enables error messages to be displayed whenthere is a problem. To avoid possible damage to the treadmill and the possibility of injury, do notoperate the treadmill until the problem is corrected. Call Keys Technical Service at (888) 3400482.17
Parts List - Alliance 815 and 835HRKEY #QTYKEY #PART #1UP 3K ASSBPART #UPRIGHT ASSEMBLYDESCRIPTION15308-0004CIRCUIT BREAKER 15 AMP1220-0001DECK ASSEMBLY15413-0017TELCO HARNESS FOR HEART RATE1320-0003ELEVATION ASSEMBLY15511-0002REAR ELEVATION BUSHING24SES EXTS.E.S. EXTENSION TUBE25611-0003UPRIGHT PIVOT BUSHING2519-0010UPRIGHT PIVOT BRACKET2619-0013SAFETY LATCH15814-0162SIDE FRAME DECAL ALLIANCE2719-0014MOTOR MOUNTING BRACKET159CONSOLE DECAL1819-0015MOTOR COVER BRACKET66014-0053AND 14005414-0190MOTOR COVER DECAL ALLIANCE1919-0029OPTICAL WHEEL BRACKET16214-0024SAFETY LATCH DECAL N/S11019-0019BELT GUIDE26314-0025WARNING FOLDING DECAL N/S16414-0026WARNING CONSOLE DECAL N/S1MOTOR TENSION SPRING11219-0032SPRING ANCHOR BRACKET26502-00781306-0018BASE PAN MOTOR16602-0002A24-0091CONSOLE ASSEMBLY 8151671605-0001SIDE BOARD EXTRUSION21706-0027PIVOT SUPPORT COVER1907-00412122DESCRIPTIONQTYDECK LIFT SPRING402-0004SCREW, 8X 5/8 PHIL PH406802-0005SCREW, 8X 5/8 PHIL PH HILO86902-0006BOLT, 5/16 X 5 - 1/2 SHOULDER BOLT127002-00075/16-18 NYLOCK NUT3HEART RATE CHEST STRAP no t shown17102-0008BOLT, 5/16-18 X 3/4 GRADE 2 ZP306-00533-PC LCD CENTER PLASTIC CONSOLE17202-0009NUT, 5/16-18 WHIZLOC306-0071FAN 5" 5/8” ID17602-0013LOCK WASHER, 1/482306-0020BASE PAN END17702-0014BOLT, 1/4-20 X 2 - 1/2 HEX102406-0004BASE PLUG27802-0015SPRING WASHER42506-0005DOME PLUG47902-0016BOLT, 3/8-16 X 2 - 1/2 HEX12606-0007MOTOR COVER18002-0017NUT, 3/8-16 NYLOCK22706-0008END CAP18102-0018PUSH NUT, 3/8 HAT42806-0009S.E.S. EXTENSION GLIDE48202-0019CARRIAGE BOLT 10-24 X 1-1/242906-0019BASE PAN CENTER18302-0020SCREW, 1/4-20 X 2-1/2 SOCKET HEAD23006-00112" ROLLER WHEEL28402-0021WASHER, 9/32 X 5/8 X 1/833106-00123” ROLLER WHEEL28502-0022NUT, 10-24 NYLOCK43206-0013UPRIGHT SPACE28702-0024CARRIAGE BOLT 5/16 X 123310-0004RUBBER FOOT38802-0025WHEEL AXLE23410-0002BOARD ISOLATOR88902-0026PUSH NUT103510-0013GRIP MOLDED WITH REMOTE29102-0028SAFETY KEY13607-0020HEART RATE RECEIVER NOT SHOWN19302-0030SCREW, 8-32 X 5/8 HEX TRILOBE13712-0022ACTUATOR (ELEVATION MOTOR)19402-0031SCREW, 3/8-16 X 1 3/4 HEX13812-0021DRIVE MOTOR13903-0004WALKING BOARD108-0090MEM, LCD PROG HR 815HR4004-0008WALKING BELT 18" X 105"19702-0034SCREW, 8-32 X 5/8 PPH N/SHOWN14104-0004POLY V BELT19802-0035NUT, 8-32 NYLOCK NOT SHOWN44209-0012FRONT ROLLER ASSEMBLY19902-0036SCREW, GREEN HEAD 8 X 5/8 PPH24309-0013REAR ROLLER108-0094MEM, LCD PROGRAM WITH INCLINE 81514413-0011POWER CORD108-0089MEM, LCD POWER 815 AND 835HR14513-0003ENCODER HARNESS110302-0040GUIDE TUBE RETAINER NOT SHOWN114-0168OVERLAY 815 W/ SPEED BAR110414-0027EMERGENCY STOP DECAL114-0152OVERLAY PROGRAM 835HR110506-0014BUSHING, STRAIN RELIEF14813-0016CONTROL PANEL HARNESS110706-0016WIRE TIES NOT SHOWN104913-0007JUMPER WIRE 6" NOT SHOWN110806-0021WIRE CLAMP NOT SHOWN507-0028UPPER LCD ELECTRONICS110906-0022RESET GUIDE TUBE NOT SHOWN15108-0014MOTOR CONTROLLER111006-0024HEX WRENCH CLIP NOT SHOWN15208-0047OPTICAL ENCODER111110-00076" CROSS HANDLEBAR FOAM GRIP182
Exploded View19
Exploded View20
Alliance 815 and 835HR Treadmills manfactured by KEYS FITNESS PRODUCTS, LP – LIMITED WARRANTYPLEASE CONSULT YOUR PHYSICIAN BEFORE USING THIS PRODUCT.This Limited Warranty applies in the United States, Canada, and Mexico to products manufactured or distributed by Keys Fitness Products, LP (“Keys”)under the ALLIANCE brand name. The warranty period to the original purchaser is (lifetime) on the frame, (10) years on the motor, (5) years on the walking belt anddeck, (2) years on par
Alliance Fitness Treadmills Manufactured in the USA by: KEYS Fitness Products, LP P.O. Box 551239 Dallas, Texas 75239 www.keysfitness.com OWNER'S MANUAL Alliance 815/835HR TREADMILL . 2 TABLE OF CONTENTS PAGE Table of Contents 2 Important Safety Information 3 Before You Start 4 Warm Up Exercises 5 Unpacking and Moving Instructions 6 .
