WIXLIB

LP116WH2Liquid Crystal DisplayProduct Specification4. Optical SpecificationOptical characteristics are determined after the unit has been ‘ON’ and stable for approximately 30 minutes ina dark environment at 25 C. The values specified are at an approximate distance 50cm from the LCD surfaceat a viewing angle of Φ and Θ equal to 0 .FIG. 1 presents additional information concerning the measurement equipment and method.FIG. 1 Optical Characteristic Measurement Equipment and MethodOptical Stage(x,y)LCD ModulePritchard 880 orequivalent50cmTable 8. OPTICAL CHARACTERISTICSTa 25 C, VCC 3.3V, fV 60Hz, fCLK TBD MHzParameterSymbolValuesMinTypMaxContrast RatioCR300--Surface Luminance, whiteLWH170200-Luminance Variationδ WHITE-1.41.6Response TimeTrR 59UnitsNotescd/m2213ms4Color CoordinatesBLUEWHITEViewing Angle5x axis, right(Φ 0 )Θr40--degreex axis, left (Φ 180 )Θl40--degreey axis, up (Φ 90 )Θu10--degreey axis, down (Φ 270 )Θd30--degreeGray ScaleVer. 0.32.2Apr. 13, 2010614 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationNote)1. Contrast Ratio(CR) is defined mathematically asSurface Luminance with all white pixelsContrast Ratio Surface Luminance with all black pixels2. Surface luminance is the average of 5 point across the LCD surface 50cm from the surface withall pixels displaying white. For more information see FIG 1.LWH Average(L1,L2, L5)3. The variation in surface luminance , The panel total variation (δ WHITE) is determined by measuring LNat each test position 1 through 13 and then defined as followed numerical formula.For more information see FIG 2.δ WHITE Maximum(L1,L2, L13)Minimum(L1,L2, L13)4. Response time is the time required for the display to transition from white to black (rise time, TrR) andfrom black to white(Decay Time, TrD). For additional information see FIG 3.5. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determinedfor the horizontal or x axis and the vertical or y axis with respect to the z axis which is normal to theLCD surface. For more information see FIG 4.* fV 60Hz6. Gray scale specificationGray LevelL0L7L15L23L31L39L47L55L63Ver. 0.3Luminance [%] (Typ)TBDTBDTBDTBDTBDTBDTBDTBDTBDApr. 13, 201015 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationFIG. 2 Luminance measuring point for surface luminance & measuring point for luminance variation HA10mm67832BV941110mm110125 13H,V : ACTIVE AREAA : H/4 mmB : V/4 mmPOINTS: 13 POINTSActive AreaFIG. 3 Response TimeThe response time is defined as the following figure and shall be measured by switching the input signalfor “black” and teblackFIG. 4 Viewing angleNormalEyeφ 180 ,LeftYφ 90 , Upθφφ 0 φ 270 Ver. 0.3,Right,DownApr. 13, 201016 / 27

LP116WH2Liquid Crystal DisplayProduct Specification5. Mechanical CharacteristicsThe contents provide general mechanical characteristics for the model LP116WH2. In addition the figuresin the next page are detailed mechanical drawing of the LCD.Outline DimensionHorizontal268.0 0.5 mmVertical169.0 0.5 mmThickness3.6mm (max)Horizontal259.35 0.5 mmVertical147.20 0.5 mmHorizontal256.13 mmVertical144.0 mmBezel AreaActive Display AreaWeightSurface TreatmentVer. 0.3235.0g (Max.)Glare treatment of the front polarizerApr. 13, 201017 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationNote) Unit:[mm], General tolerance: 0.5mm FRONT VIEW Ver. 0.3Apr. 13, 201018 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationNote) Unit:[mm], General tolerance: 0.5mm REAR VIEW Ver. 0.3Apr. 13, 201019 / 27

LP116WH2Liquid Crystal DisplayProduct Specification6. ReliabilityEnvironment test conditionNo.Test ItemConditions1High temperature storage testTa 60 C, 240h2Low temperature storage testTa -20 C, 240h3High temperature operation testTa 50 C, 50%RH, 240h4Low temperature operation testTa 0 C, 240h5Vibration test (non-operating)Sine wave, 10 500 10Hz, 1.5G, 0.37oct/min3 axis, 1hour/axis6Shock test (non-operating)Half sine wave, 180G, 2msone shock of each six faces(I.e. run 180G 6msfor all six faces)7Altitude0 10,000 feet (3,048m) 24Hr0 40,000 feet (12,192m) 24Hroperatingstorage / shipment{ Result Evaluation Criteria }There should be no change which might affect the practical display function when the display qualitytest is conducted under normal operating condition.Ver. 0.3Apr. 13, 201020 / 27

LP116WH2Liquid Crystal DisplayProduct Specification7. International Standards7-1. Safetya) UL 60950-1, Second Edition, Underwriters Laboratories Inc.Information Technology Equipment - Safety - Part 1 : General Requirements.b) CAN/CSA C22.2 No.60950-1-07, Second Edition, Canadian Standards Association.Information Technology Equipment - Safety - Part 1 : General Requirements.c) EN 60950-1:2006 A11:2009, European Committee for Electrotechnical Standardization (CENELEC).Information Technology Equipment - Safety - Part 1 : General Requirements.d) IEC 60950-1:2005, Second Edition, The International Electrotechnical Commission (IEC).Information Technology Equipment - Safety - Part 1 : General Requirements.7-2. EMCa) ANSI C63.4 “American National Standard for Methods of Measurement of Radio-NoiseEmissions from Low-Voltage Electrical and Electronic Equipment in the Range of 9 kHz to 40 GHz.”American National Standards Institute (ANSI), 2003.b) CISPR 22 “Information technology equipment – Radio disturbance characteristics – Limit andmethods of measurement." International Special Committee on Radio Interference(CISPR), 2005.c) CISPR 13 “Sound and television broadcast receivers and associated equipment – Radio disturbancecharacteristics – Limits and method of measurement." International Special Committee on RadioInterference (CISPR), 2006.7-3. Environmenta) RoHS, Directive 2002/95/EC of the European Parliament and of the council of 27 January 2003Ver. 0.3Apr. 13, 201021 / 27

LP116WH2Liquid Crystal DisplayProduct Specification8. Packing8-1. Designation of Lot Marka) Lot MarkABCDEFGHA,B,C : SIZE(INCH)E : MONTHIJKLMD : YEARF M : SERIAL NO.Note1. DecMark123456789ABC2. MONTHb) Location of Lot MarkSerial No. is printed on the label. The label is attached to the backside of the LCD module.This is subject to change without prior notice.8-2. Packing Forma) Package quantity in one box : 30 pcsb) Box Size : 480 x 388 x 240Ver. 0.3Apr. 13, 201022 / 27

LP116WH2Liquid Crystal DisplayProduct Specification9. PRECAUTIONSPlease pay attention to the followings when you use this TFT LCD module.9-1. MOUNTING PRECAUTIONS(1) You must mount a module using holes arranged in four corners or four sides.(2) You should consider the mounting structure so that uneven force (ex. Twisted stress) is not applied to themodule. And the case on which a module is mounted should have sufficient strength so that externalforce is not transmitted directly to the module.(3) Please attach the surface transparent protective plate to the surface in order to protect the polarizer.Transparent protective plate should have sufficient strength in order to the resist external force.(4) You should adopt radiation structure to satisfy the temperature specification.(5) Acetic acid type and chlorine type materials for the cover case are not desirable because the formergenerates corrosive gas of attacking the polarizer at high temperature and the latter causes circuit breakby electro-chemical reaction.(6) Do not touch, push or rub the exposed polarizers with glass, tweezers or anything harder than HBpencil lead. And please do not rub with dust clothes with chemical treatment.Do not touch the surface of polarizer for bare hand or greasy cloth.(Some cosmetics are detrimentalto the polarizer.)(7) When the surface becomes dusty, please wipe gently with absorbent cotton or other soft materials likechamois soaks with petroleum benzene. Normal-hexane is recommended for cleaning the adhesivesused to attach front / rear polarizers. Do not use acetone, toluene and alcohol because they causechemical damage to the polarizer.(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causesdeformations and color fading.(9) Do not open the case because inside circuits do not have sufficient strength.9-2. OPERATING PRECAUTIONS(1) The spike noise causes the mis-operation of circuits. It should be lower than following voltage :V 200mV(Over and under shoot voltage)(2) Response time depends on the temperature.(In lower temperature, it becomes longer.)(3) Brightness depends on the temperature. (In lower temperature, it becomes lower.)And in lower temperature, response time(required time that brightness is stable after turned on) becomeslonger.(4) Be careful for condensation at sudden temperature change. Condensation makes damage to polarizer orelectrical contacted parts. And after fading condensation, smear or spot will occur.(5) When fixed patterns are displayed for a long time, remnant image is likely to occur.(6) Module has high frequency circuits. Sufficient suppression to the electromagnetic interference shall bedone by system manufacturers. Grounding and shielding methods may be important to minimized theinterference.Ver. 0.3Apr. 13, 201023 / 27

LP116WH2Liquid Crystal DisplayProduct Specification9-3. ELECTROSTATIC DISCHARGE CONTROLSince a module is composed of electronic circuits, it is not strong to electrostatic discharge. Make certain thattreatment persons are connected to ground through wrist band etc. And don’t touch interface pin directly.9-4. PRECAUTIONS FOR STRONG LIGHT EXPOSUREStrong light exposure causes degradation of polarizer and color filter.9-5. STORAGEWhen storing modules as spares for a long time, the following precautions are necessary.(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep thetemperature between 5 C and 35 C at normal humidity.(2) The polarizer surface should not come in contact with any other object.It is recommended that they be stored in the container in which they were shipped.9-6. HANDLING PRECAUTIONS FOR PROTECTION FILM(1) When the protection film is peeled off, static electricity is generated between the film and polarizer.This should be peeled off slowly and carefully by people who are electrically grounded and with wellion-blown equipment or in such a condition, etc.(2) The protection film is attached to the polarizer with a small amount of glue. If some stress is appliedto rub the protection film against the polarizer during the time you peel off the film, the glue is apt toremain on the polarizer.Please carefully peel off the protection film without rubbing it against the polarizer.(3) When the module with protection film attached is stored for a long time, sometimes there remains avery small amount of glue still on the polarizer after the protection film is peeled off.(4) You can remove the glue easily. When the glue remains on the polarizer surface or its vestige isrecognized, please wipe them off with absorbent cotton waste or other soft material like chamoissoaked with normal-hexane.Ver. 0.3Apr. 13, 201024 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationStandard Timing IDEstablishedTimingsPanel ColorCoordinatesDisplayParametersVendor / ProductEDID VersionHeaderAPPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM)Ver. 102030405060708090A0B0C0D0E0F10111812EDID structure version # 11913EDID revision # 32014Video input Definition Digital signal2115Max H image size (Rounded cm) 26 cm2216Max V image size (Rounded cm) 14 cm2317241/3Value(Hex)Value(Bin)00000000Display gamma (gamma*100)-100 Example:(2.2*100)-100 120 2.2 E7818Feature Support (no DPMS, no Active Off/Very Low Power, RGB color display, Timing BLK 1,no GTF)0A000010102526191ARed/Green Low Bits (RxRy/GxGy)Blue/White Low Bits (BxBy/WxWy)10111111271BRed XRx 0.584281CRed YRy 0.347291DGreen X Gx 0.323301EGreen Y Gy 0.542311FBlue XBx 0.1573220Blue YBy 0.1453321White X Wx 0.3133422White Y Wy 0.329BF459558528A282550543523Established timing 1 (00h if not used)00000000003624Established timing 2 (00h if not used)00000000003725Manufacturer's timings (00h if not 728292A2B2C2D2E2F303132333435Standard timing ID1 (01h if not used)Standard timing ID1 (01h if not used)Standard timing ID2 (01h if not used)Standard timing ID2 (01h if not used)Standard timing ID3 (01h if not used)Standard timing ID3 (01h if not used)Standard timing ID4 (01h if not used)Standard timing ID4 (01h if not used)Standard timing ID5 (01h if not used)Standard timing ID5 (01h if not used)Standard timing ID6 (01h if not used)Standard timing ID6 (01h if not used)Standard timing ID7 (01h if not used)Standard timing ID7 (01h if not used)Standard timing ID8 (01h if not used)Standard timing ID8 (01h if not used)0101010101010101010101010101010100000001Field Name and HeaderEISA manufacture code ( 3 Character ID )EISA manufacture code (Compressed ASCⅡ)Panel Supplier Reserved - Product Code( Hex. LSB first )LCD Module Serial No - Preferred but Optional ("0" If not used)LCD Module Serial No - Preferred but Optional ("0" If not used)LCD Module Serial No - Preferred but Optional ("0" If not used)LCD Module Serial No - Preferred but Optional ("0" If not used)Week of ManufactureYear of ManufactureApr. 13, 2010LGD0000h0 000000010000000100000001000000010000000125 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationTiming Descriptor #3Timing Descriptor #2Timing Descriptor #1APPENDIX A. Enhanced Extended Display Identification Data (EEDIDTM)Ver. 0.3Byte(Dec)5455Byte(Hex)36375638Horizontal Active(lower 8 bits)1366 Pixels5739Horizontal Blanking(Thp-HA)(lower 8 bits)168 Pixels583AHorizontal Active / Horizontal Blanking(Thp-HA) (upper 4:4bits)593BVertical Avtive603CVertical Blanking (Tvp-HA) (DE Blanking typ.for DE only panels)613DVertical Active : Vertical Blanking (Tvp-HA) (upper 4:4bits)623EHorizontal Sync. Offset (Thfp)48 Pixels633FHorizontal Sync Pulse Width (HSPW)32 Pixels6440Vertical Sync Offset(Tvfp) : Sync Width (VSPW)6541Horizontal Vertical Sync Offset/Width6642Horizontal Image Size (mm)256 mm6743Vertical Image Size144 mm6844Horizontal Image Size / Vertical Image Size6945Horizontal Border 0 (Zero for Notebook LCD)7046714772734849Vertical Border 0 (Zero for Notebook LCD)Non-Interlace, Normal display, no stereo, Digital Separate ( Vsync NEG, Hsync POS ), DE only note :LSB is set to '1' if panel is DE-timing only. H/V can be ignored.FlagFlag744AFlag754BData Type Tag (Descriptor Defined by manufacturer )764CFlag774DDescriptor Defined by manufacturer784EDescriptor Defined by manufacturer794FDescriptor Defined by manufacturer8050Descriptor Defined by manufacturer8151Descriptor Defined by manufacturer8252Descriptor Defined by manufacturer8353Descriptor Defined by manufacturer8454Descriptor Defined by manufacturer8555Descriptor Defined by manufacturer8656Descriptor Defined by manufacturer8757Descriptor Defined by manufacturer8858Descriptor Defined by manufacturer8959Descriptor Defined by manufacturer90915A5BFlagFlag925CFlag935DData Type Tag ( ASCII String )945EFlag955FASCII StringL9660ASCII StringG9761ASCII String9862ASCII StringD9963ASCII Stringi10064ASCII Strings10165ASCII Stringp10266ASCII Stringl10367ASCII Stringa10468ASCII Stringy10569Manufacturer P/N(If 13 char-- 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char 20h)1066AManufacturer P/N(If 13 char-- 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char 20h)1076BManufacturer P/N(If 13 char-- 0Ah, then terminate with ASCⅡ code 0Ah,set remaining char 20h)Field Name and CommentsPixel Clock/10,000 (LSB)Pixel Clock/10,000 (MSB)73 MHz @ 60.01Hz768 Lines25 Lines3 Lines : 5 Lines(upper 2bits)(mm)Apr. 13, 0001000000010000026 / 27

LP116WH2Liquid Crystal DisplayProduct SpecificationChecksumTiming Descriptor #4APPENDIX A. Enhanced Extended Display Identification Data Flag1116FData Type Tag ( ASCII String )11270Flag11371ASCII StringL11472ASCII StringP11573ASCII String111674ASCII String111775ASCII String611876ASCII StringW11977ASCII StringH12078ASCII String212179ASCII String-1227AASCII Strin

Product Specification 1/ 27 LP116WH2 Liquid Crystal Display Ver. 0.3 Apr. 13, 2010 SPECIFICATION. FOR. APPROVAL. Title. 11.6" HD TFT LCD