Transcription
FrelTec GmbHMathildenstr. 10A82319 StarnbergGermanyThick Film Chip ResistorSMD 0100512/28/2015 Freltec GmbHPlease read cautions and warnings and important notes at the end of this document.1/11www.freltec.com
FrelTecThick Film Chip Resistors ypeSizeValueTolerancePacking010 : SMD ThickFilm ChipResistor0A : 01005F : 1%H20: Tape and reelfor 20k pc (7”reel)R DecimalThe last digit isthe multiplierwhich denotesthe number ofzero following0000 0OhmJ : 5%Example:97R6 97,6Ohm9760 976Ohm*1001 1kOhmE24-Series isfirst digit “0”not all combination ispossible** H20 for 01005Paper Type, 2mmPitchAll products according to RoHS (2011/65/EU)And according to REACH, status June 201512/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.2/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDTHICK FILM CHIP RESISTORS1Ceramic substrate62Bottom inner electrode72nd Protective coatingTerminal inner electrode3Top inner electrode8Ni plating4Resistive layer9Sn plating51st Protective coatingPlating Thickness:Ni:Sn(Tin):Sn(Tin): 1µm 3µmMatte SnDimensionsSIZE01005L0,40 0,02W0,20 0,02L10,10 0,0312/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.L20,10 0,03H0,13 0,02(unit: mm)3/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDPower Derating CurveOperated in ambient temperatures above 70 , power rating must be derated in accordancewith the curve below. Operating temperature -55 C to 125 C100Related Load [%]806040200-50-40 -30-20 -100102030405060708090100 110 120 130 140Temperature [ C]Voltage Rating:Rated Voltage: The resistor shall have a DC continuous working voltage or a rms ACcontinuous working voltage at commercial-line frequency and wave form corresponding to thepower rating, as determined from the following:E Rated voltage [V]P Power rating [W]E R PR Nominal resistance [Ω]THICK FILM CHIP RESISTORSRating010 SeriesGENERAL PURPOSE CHIP RESISTORSTypeSizePowerMax.Max.Rating Working OverloadatVoltage Voltage70 CTemperatureCoefficient[TCR;ppm/ C]Resistance Range [Ω]F( 1%)E-96, E-240100A 01005 1/32W15V30V-200 600 250J( 5%)E-241Ω R 10Ω10Ω R 1MΩJumperRatedCurrentJumperResistanceValueJ( 5%)E-24J( 5%)E-240,5A50m ΩMaxMarking:01005 no marking12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.4/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDP0P2EDFWBP1AAccumulated dimensional tolerance 40 0,2mmIn Accordance with EIA RS-481PackingSizeAPaperTape(H)010A(01005)0,25 0,02BWFEP1P2P00,45 0,02 8,00 0,30 3,50 0,05 1,75 0,10 2,00 0,05 2,00 0,05 4,0 0,05DT1T21,5 0,1/-00,31 0,030,17 0,03Lead Dimensions:12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.5/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDCover Tape Peel off StrengthSpecifications:01005 0,07 0,5N (7,1 51gf)SymbolReel Type /TapeANDimension7” reel for 8mm Tape178 2,060,0 1,0CD13,5 0,5 21,0 0,5BG2,0 0,59,0 0,5inmmStock periodThe temperature condition must be controlled at 25 5 C, the R.H. must be controlled at60 15%. The stock can maintain quality level in one years.12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.6/11www.freltec.com
Lead Free Reflow Soldering ProfileRemark: The peak temperature of soldering heat is 260 5/-0 C for 10 seconds.Recommended Land Pattern Design (For Reflow Soldering):SizeABC010050,200,500,2012/28/2015 Freltec GmbHPlease read cautions and warnings and important notes at the end of this document.7/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDReliability TestElectrical Performance TestSPECIFICATIONResistorITEM01005: ΔR (2,0% 0,10Ω)Short timeOverloadJumperRefer togeneralspecificationNo evidence of mechanical damage.No short or burned on the nsulationResistanceRefer to general specification aboveNATEST METHODJIS C 5201-1 4.13Applied 2,5 times rated voltage for 5 s and releasethe load for about 30 min, then measure itsresistance variance rate. (Rated voltage refer toabove item “General specifications”)Jumper: Applied Maximum overload current 1,25AJIS C 5201-1 4.8R1: Resistance at room temperatureR2: Resistance at -55 or 125 T1: Room temperatureT2:Temperature -55 or 125 TCR ( ppm / C ) R 2 R11 10 6R1T 2 T1JIS C 5201-1 4.6Put the resistor in the fixture, add 100 VDC in ,terminal for 60 s then measured the insulationresistance between electrodes and insulatingenclosure or between electrodes and base material.Between termination and coating must be over 1.000MΩ12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.8/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDMechanical Performance TestSPECIFICATIONResistorJumperITEMTEST METHODResistanceto solventNo evidence of mechanical damage, no G2 overcoating and Sn layer by leaching.JIS-C5201-1 4.29The tested resistor be immersed into isopropyl alcohol of20 25 C for 5 min, then the resistor is left in the room for 48h,and measured its resistance variance rate.Solderability1.Test item 1:Solder coverage over 95%2.Test item 2:Zero cross time within 3 s.JIS-C5201-1 4.17Add flux into tested resistors, immersion into solder bath intemperature 235 3 C for 2 0,5 s.Resistanceto solderingheat01005: ΔR (2,0% 0,10Ω)RefergeneralspecificationsNo evidence of electrode damage.No side conductive peeling off.JIS-C5201-1 4.18The tested resistor be immersed into molten solder of260 5 C for 10 s, then the tested resistor is left in theroom for 1 hour, and measure its resistance variancerate.JIS-C5201-1 4.33Solder tested resistor on to PC board. Add force in the middledown, and under load measured its resistance variance rate.D 3mmBendingStrength01005: ΔR (1,0% 0,05Ω)Refergeneralspecifications12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.9/11www.freltec.com
FrelTecThick Film Chip Resistors 01005SMDEnvironmental TestSPECIFICATIONResistorITEMResistanceto DryHeat01005: (2,0% 0,10Ω)RefergeneralspecificationsNo evidence of mechanical damage.No short or burned on the appearance01005: (2,0% 0,10Ω)RefergeneralspecificationsThermalShockNo evidence of mechanical damage.No short or burned on the appearanceLoadingLife inMoistureLoad LifeType01005Range (5,0% 0,10Ω)TEST METHODJumperRefergeneralspecificationsNo evidence of mechanical damage.No short or burned on the appearanceRefergeneral01005: (5,0% 0,10Ω)specificationsNo evidence of mechanical damage.No short or burned on the appearanceJIS-C5201-1 4.25Put tested resistor in chamber under temperature 125 5 C for 1000 48/-0 h. Then leaving the tested resistorin room temperature for 60 min, and measure itsresistance variance rate.01005 and 0201 for 125 3 CMIL-STD 202 Method 107Put the tested resistor in the chamber under thetemperature cycle which shown in the following tableshall be repeated 300 times consecutively. Then leavingthe tested resistor in the room temperature for 1 h, andmeasure its resistance variance rate.StepTemperatureLowest Temperature-55 5 CHighest Temperature125 5 CTemperature-retaining time 15 minutes eachJIS-C5201-1 4.24Put the tested resistor in the chamber undertemperature 40 2 C, relative humidity 90 95% andload the rated voltage for 90 min on, 30 minutes off, total1000 h. Then leaving the tested resistor in roomtemperature for 60 minutes, and measure its resistancevariance rate.JIS-C5201-1 4.25Put the tested resistor in chamber under temperature70 2 C and load the rated voltage for 90 min on, 30min off, total 1000 h. Then leaving the tested resistor inroom temperature for 60 min, and measure itsresistance variance rate.12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.10/11www.freltec.com
SMDFrelTecThick Film Chip Resistors 01005Published by FrelTec GmbHMathildenstr. 10A; 82319 Starnberg; Germany 2015 FrelTec GmbH. All Rights Reserved.The following applies to all products named in this publication:1. The information describes the type of component and shall not be considered as assured characteristics.2. Terms of delivery and rights to change design reserved.3. Some parts of this publication contain statements about the suitability of our products for certain areas ofapplication. These statements are based on our knowledge of typical requirements that are often placed onour products in the areas of application concerned. Nevertheless, we explicitly point out that suchstatements cannot be regarded as binding statements about the suitability of our products for a particularcustomer application. As a rule, Freltec is either unfamiliar with individual customer applications or lessfamiliar with them than the customers themselves. For these reasons, it is always ultimately incumbent onthe customer to check and decide whether a FrelTec product with the properties described in the productspecification is suitable for use in a particular customer application.4. We also point out that in individual cases, a malfunction of electronic components or failure before the endof their usual service life cannot be completely ruled out in the current state of the art, even if they areoperated as specified. In customer applications requiring a very high level of operational safety andespecially in customer applications in which the malfunction or failure of an electronic component couldendanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore beensured by means of suitable design of the customer application or other action taken by the customer(e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third partiesin the event of malfunction or failure of an electronic component.5. The warnings, cautions and product-specific notes must be observed.6. In order to satisfy certain technical requirements, some of the products described in this publication maycontain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as“hazardous”). Useful information on this will be found in our Material Data Sheets. Should you have anymore detailed questions, please contact our sales offices.7. We constantly strive to improve our products. Consequently, the products described in this publication maychange from time to time. The same is true for the corresponding product specifications. Please checktherefore to what extent product descriptions and specifications contained in this publication are stillapplicable before or when you place an order. We also reserve the right to discontinue production anddelivery of products. Consequently, we cannot guarantee that all products named in this publication willalways be available.8. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “Generalconditions for the supply of products and services of the electrical and electronics industry” published bythe German Electrical and Electronics Industry Association (ZVEI), available at www.freltec.com.9. As far as patents or other rights of third parties are concerned, liability is only assumed for components per se,not for applications, processes and circuits implemented within components or assemblies.10. The trade name FrelTec is a trademark registered or pending in Europe and in other countries.12/28/2015 FrelTec GmbHPlease read cautions and warnings and important notes at the end of this document.11/11www.freltec.com
The tested resistor be immersed into isopropyl alcohol of 20 25 C for 5 min, then the resistor is left in the room for 48h, and measured its resistance variance rate. Solder-ability 1.Test item 1: Solder coverage over 95% 2.Test item 2: Zero cross time within 3 s. JIS-C5201-1 4.17 Add flux into tested resistors, immersion into solder bath inFile Size: 293KBPage Count: 11
