Transcription
G2 - STELLAR/BENTLEYseriesTechnical Reference ManualBENTLEYSTELLARSTELLAR GLPDG Product Design Group318 East Kent Ave S, Unit 103Vancouver, BC, V5X 4N6Phone: 604-323-9200 or Toll Free Phone: 888-858-4422Fax: 604-323-9097 or Toll Free Fax: 877-323-9093www.pdgmobility.comPage 1 of 33
AXLE PLATE SETUP1CASTERS2ANTI-TIPPERS3SEAT HEIGHT4GAS STRUT ADJUSTMENT/ TILT LIMITER5SEAT DEPTH6BACK7ARM SETUP8FRONT RIGGING HANGER9WHEELS10RECLINING BACK11Page 2 of 33
Reference Point16"18"19"520"/21"22"6Dimensioning and Tolerancing Standard ASME .56.752.25666.256.5 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityRTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15Technical referenceMichael JalmarsonCaitlin LukowTitle:Bentley/Stellar/Stellar GL - Axle Plate Position ChartAuthorNote 6: For Stellar positions A-E see Drawing 85055Note 5: For Bentley positions A-E see Drawing 85055Note 4: For Stellar GL positions A-D see Drawing 85055Note 3: For use of rocker back, put rocker back at 2"UnitsmmKeira LaneRevised byApproved by6.56.752.25666.256.5Sheet1 of 1Date of Issue2016 Sept 6Torr BrownFile name (Drawing #)85001Note 2: For Stellar, reduce position by 1.5" if 30 degree reclining back option is chosen.PDG part numberNA6.5C6.5D6Note 1: Reduce position by 1/2" if back angle is above 98 sNACUS: [ ]13534Update drawing references3ECO#2Revision descriptionAxle Plate1Printed: Wednesday, September 07, 2016 Created: Tuesday, March 19, 2013 1:50:22 PM Saved: Tuesday, September 06, 2016 2:56:26 PM By: klane Checked Date: 2016 September 6Lower Frame2RevFile : 85001 R: 2Page 3 of 33DCBA
Page 4 of 332Updated for G2 releaseRevision descriptionNOTE:1.Right hand side shown, left is a mirrorimage.2.Attendant and Dual style axle plates causetie down incompatibly.StellarBentleyFor 24" wheelsRUnitsmmVinh TranFor 12" and 16"wheelsSheet1 of 1Date of Issue2015 July 08Approved byRevision2StatusNACUS: [ ]For 12" and 16"wheelsJim FormbyFile name (Drawing #)85002For 16"Wheel-lockFor 12"Wheel-lockRevised byTolerances unless otherwise stated:Angular: /- 1ºOther: x /-0.8, x.x /-0.4, x.xx /-0.15Technical referenceFor 20"/22"wheelsN/ATorr BrownTitle:Bentley / Stellar Axle Plate Assembly ChartAuthor 2010 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityN/APDG part numberFor 24"Wheel-lockFor 22"Wheel-lockFor 20"Wheel-lock1477Axle Plate for 12" and 16"Attendant only or DualFor 12" Wheel-lockFor 20"/22" wheels6ECO#Axle Plate for 12" and 16"User only5For 16" Wheel-lockAxle Plate for 20", 22" and 24"DualStellarBentley4For 22" Wheel-lockFor 20" Wheel-lockFor 24" wheels3For 24" Wheel-lockAxle Plate for 20", 22" and 24"User only or Attendant only1Printed: Friday, July 10, 2015 Created: Tuesday, January 31, 2012 5:18:47 PM Saved: Friday, July 10, 2015 10:43:13 AM By: vtran Checked Date: 2015 July 08Dimensioning and Tolerancing Standard ASME Y14.5-20092RevFile : 85002 R: 2DCBA
Page 5 of 332Hole Position6" Caster, 6" Fork, HP 1R5Tolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15CLUnits[mm]Revised bySheet1 of 1Date of Issue2013-Mar-26TBFile name (Drawing #)85003Approved by6Revision1StatusNACUS: [ ]1353ECO#8" Caster, 8" Fork, HP 116"/24" Rear Wheel6" Caster, 8" Fork, HP 2Technical reference4MJCLTitle:Bentley/Stellar/Stellar GL - Caster Selection ChartAuthor6" Caster, 8" Fork, HP 1 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNAPDG part number6" Caster, 6" Fork, HP 2HP 2HP 1322" Rear WheelDEFAULTUpdate Template, add configurationsRevision description12"/20" Rear Wheel1Printed: Wednesday, July 15, 2015 Created: Tuesday, March 26, 2013 10:55:55 AM Saved: Friday, September 05, 2014 1:51:33 AM By: njuras Checked Date: 2013-Mar-26Dimensioning and Tolerancing Standard ASME Y14.5-20091RevFile : 85003 R: 1DCBA
Page 6 of 33123R64253116", 22" and 24" Rear Wheel Antitippers561281ECO#Note: Use figure above to locate antitip position 1to 6 on the Table below. Positions 1 to 3 can beused to make the chair more stable but will reducethe caster ground clearance when the wheelchairis tipped backwards on to antitippers.4Tolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15MJUnits[mm]Revised byDZSheet1 of 1Date of Issue2012 Jan 30WSFile name (Drawing #)8500456No Extension Tube45StatusCUS: []Revision16NA7" to 8"Approved by4-3/4" to 6-3/4"3-1/2" to 4-1/2"Technical referenceProduct and AxlePlate PositionStellar / GLBentleyEclipse16", 22" and 24" Wheel Antipper Assembly Length AdjustmentUse with and without Telescoping Antipper OptionTBTitle:B/S/E Antitipper SelectionAuthor 2010 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityPDG part numberStandard Eclipse Anti-tipper Assembly.Note: Eclipse chairs fitted with recline backoption use anti-tipper tube 55111.16", 22" and 24" Wheel Anti-tipper Assemblyfor use with HD Telescopic Antipper OptionUse modified tube. See drawing 55594.16", 22" and 24" Wheel Anti-tipper Assembly12" and 20" Wheel Anti-tipper AssemblyAdd set up options for B/S with HD Telescopic Anti-tipper, also for Eclipse chairsRevision descriptionPrinted: Thursday, February 20, 2014 Created: Tuesday, October 13, 2009 7:58:02 AM Saved: Thursday, February 20, 2014 5:12:32 PM By: dzhu Checked Date:Dimensioning and Tolerancing Standard ASME Y14.5-20091RevFile : 85004 R: 1DCBA
Page 7 of l reference4Revised by5Approved byMounting HolesDCBATolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmSheet1 of 3Date of Issue2016 Sept 7Bahareh AshtianiBahareh AshtianiKeira LaneTorr BrownTitle:File name (Drawing #)85055Taco Tuesday - B/S/GL Chair Seat Height Adjustment ChartAuthor 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityRDCBASub FrameHole PositionPDG part numberNANote 1: See Drawing 85003 for caster set-up specificationsSeat Height22" RearWheel12"/20" RearWheel16"/24" RearWheelUpdated to include Bentley Extended Seat To FloorRevision descriptionSTELLAR GL1Printed: Wednesday, September 07, 2016 Created: Thursday, October 23, 2014 2:53:09 PM Saved: Wednesday, September 07, 2016 11:09:44 AM By: klane Checked Date: 2016 Sept 7Dimensioning and Tolerancing Standard ASME Y14.5-20091RevFile : 85055 R: 16Revision1StatusNACUS: [ ]1534ECO#DCBA
Page 8 of 33215"16"14"15"L19"18"3AuthorEDCBATechnical reference4Revised by5Approved byTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmSheet2 of 3Date of Issue2016 Sept 7Bahareh AshtianiBahareh AshtianiKeira LaneTorr BrownTitle:File name (Drawing #)85055Taco Tuesday - B/S/GL Chair Seat Height Adjustment Chart 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityR20"19"18"17"16"Lower Frame HolePositionSTELLAR16"/24" Rear Wheelwith 8" CasterPDG part number18"17"NA17"16"L22" Rear Wheelwith 6" Caster12"/20" Rear Wheelwith 6" CasterUpdated to include Bentley Extended Seat To FloorRevision descriptionSeat Height1Printed: Wednesday, September 07, 2016 Created: Thursday, October 23, 2014 2:53:09 PM Saved: Wednesday, September 07, 2016 11:09:44 AM By: klane Checked Date: 2016 Sept 7Dimensioning and Tolerancing Standard ASME Y14.5-20091RevFile : 85055 R: 16StatusNARevision1EDCBA1534ECO#DCBA
Page 9 of 33234PDG part numberRAuthor1534DECONLY SUB-FRAMEMOUNTING PLATESHOWNBentley Higher Seat to Floor(H-STF)BENTLEYTechnical referenceTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.156ECO#Revised byFEDCApproved byUnitsmmSheet3 of 3Date of Issue2016 Sept 7Revision1StatusNAONLY SUB-FRAMEMOUNTING PLATESHOWNBentley Extended Seat to TFE-STFE-STFNotes5Bahareh AshtianiBahareh AshtianiKeira LaneTorr BrownTitle:File name (Drawing #)85055Taco Tuesday - B/S/GL Chair Seat Height Adjustment Chart 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNACBAREFERENCE MOUNTINGHOLEBentley Lower Seat to Floor(L-STF)12"/20"Rear Wheel 22" Rear Wheel with 16"/24" Rear Wheel Lower Frame Holewith 6"Caster6" Casterwith 8" 18"19"20"FUpdated to include Bentley Extended Seat To FloorRevision descriptionSeat Height1Printed: Wednesday, September 07, 2016 Created: Thursday, October 23, 2014 2:53:09 PM Saved: Wednesday, September 07, 2016 11:09:44 AM By: klane Checked Date: 2016 Sept 7Dimensioning and Tolerancing Standard ASME Y14.5-20091RevFile : 85055 R: 1DCBA
Page 10 of 3381716Initial ReleaseRevision description522Dimensioning and Tolerancing Standard ASME Y14.5-2009RAuthor6411G2 - Tie Down - Rear12Tolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.151479Approved 875578855781NumberUnitsmmSheet1 of 2Date of Issue2015 June 09Revision0StatusNA244611622221WithTiedown/QTYCUS: [20621]Bahareh AshtianiJim FormbyFile name (Drawing #)55780Revised by1/4-20 x 1-1/2" Socket Button Head - Black Zinc1/4-20 Nylon Locknut1011Technical reference5/16-18 x 7/8 L Flat Head Screw# 8 x 3/8" self-tapping phillips pan head screwBentley/Stellar Seat Pan Edge Moulding Rounded With GlueBentley/Stellar Seat Pan Edge Moulding Rounded With Glue6G2 - Rear Seat Depth InsertBentley/Stellar Fold Down Back Bracket3/8-16 x 1" w 5/8" thread - socket head cap screw - Black ZincG2 - Upper Frame - Seat Pan7896ECO#See Configuration25345G2 - Upper Frame - Bonded Assembly1Item Part Name or Description1234Jim FormbyBahareh AshtianiTitle:G2 - Common Upper Frame Assembly9 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNAPDG part number103Printed: Thursday, July 09, 2015 Created: Thursday, January 22, 2015 5:45:34 PM Saved: Wednesday, July 08, 2015 4:10:11 PM By: jformby Checked Date: YYYY/MMM/DDNotes:1. Material: As per detailed part2. Remove burrs & sharp edges.3. Finish : See purchase order4. Component weight [grams]: 6454.215. All holes are through unless otherwise specified6. Dimensional limits apply before coating.7. Maximum coating thickness is 0.1mm.0RevFile : 55780 R: 0DCBA
Page 11 of 3315Initial ReleaseRevision description7162Dimensioning and Tolerancing Standard ASME Y14.5-2009R4Author82G2 - Upper Frame - Seat Pan5/16-18 x 7/8 L Flat Head Screw# 8 x 3/8" self-tapping phillips pan head screwBentley/Stellar Seat Pan Edge Moulding Rounded With GlueBentley/Stellar Seat Pan Edge Moulding Rounded With Glue1/4-20 x 1-1/2" Socket Button Head - Black Zinc456789Technical referenceTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx 5578855781Sheet2 of 2Date of Issue2015 June 09Bahareh AshtianiJim FormbyFile name (Drawing outNumber Tie-Down/QTY.Approved byBentley/Stellar Fold Down Back Bracket3Revised byG2 - Rear Seat Depth Insert210 1/4-20 Nylon LocknutG2 - Upper Frame - Bonded AssemblySee Configuration51Item Part Name or Description104Jim FormbyBahareh AshtianiTitle:G2 - Common Upper Frame Assembly3 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNAPDG part numberCUS: [20621]93Printed: Thursday, July 09, 2015 Created: Thursday, January 22, 2015 5:45:34 PM Saved: Wednesday, July 08, 2015 4:10:11 PM By: jformby Checked Date: YYYY/MMM/DDNotes:1. Material: As per detailed part2. Remove burrs & sharp edges.3. Finish : See purchase order4. Component weight [grams]: 6454.215. All holes are through unless otherwise specified6. Dimensional limits apply before coating.7. Maximum coating thickness is 0.1mm.0RevFile : 55780 R: 0DCBA
Page 12 of 331376Initial ReleaseRevision description11112141324Dimensioning and Tolerancing Standard ASME Y14.5-20092R121155555812432Stellar GL - Cap - Lower Frame - Front Cap (RH/LH)B/S Axle Plate Assembly (20"/22"/24" Wheel) (RH/LH)B/S Axle Plate Assembly (20"/22"/24" Wheel) (LH/RH)# 8 x 3/8" self-tapping phillips pan head screw0.216" ID x 0.512" OD x 3/64" Washer Steel Black (#10)Stellar GL - Cap - Axle plate 20" 24"# 10-14 x 5/8" self-tapping phillips pan head screw - black zinc3456789557641600314 G2 - Lower Frame - Mounting Bracket with Tie Down (RH/LH)15 Ruler LabelTolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmJim Formby1479CUS: [20640]211142622211121Sheet1 of 2Date of Issue2015 June 02Revision0Bahareh AshtianiFile name (Drawing #)Status55760NAApproved by557615576412 G2 - Lower Frame - Weldment13 G2 - Lower Frame - Mounting Bracket with Tie Down (LH/RH)Revised by1201911 Bearing R8ZZ (1/2 ID x 1 1/8 OD x 5/16 Width)(RS type acceptable)Technical reference5555710 Stellar GL - Cap - Lower Frame - Back1206755576555765555912192Caster & Fork Assembly55559Stellar GL - Cap - Lower Frame - Front Cap (LH/RH)Author6ECO#- with TieNumber ShortDowns/QTY.251Item Part Name or DescriptionSee 85002 for setup5101594Torr BrownTorr BrownTitle:G2 - Lower Frame Assembly12See configuration 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityPDG part numberNA983Printed: July-08-15 Created: December-16-10 11:21:26 AM Saved: July-08-15 4:14:10 PM By: jformby Checked Date: 2015 Feb 04Notes:1. Material: As per detailed part2. Remove burrs & sharp edges.3. Finish : As per detailed part4. Component weight [grams]: 8059.615. All holes are through unless otherwise specified6. Dimensional limits apply before coating.7. Maximum coating thickness is 0.1mm.8. General tolerance of 0.15 mm.0RevFile : 55760 R: 0DCBA
Page 13 of 33Initial ReleaseRevision description3176821111324NA5Bearing R8ZZ (1/2 ID x 1 1/8 OD x 5/16 Width)(RS typeacceptable)1011Technical referenceUnitsmmJim FormbyRevised byTolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15Torr BrownTorr BrownTitle:G2 - Lower Frame AssemblyAuthor 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityRStellar GL - Cap - Lower Frame - Back9Ruler Label# 10-14 x 5/8" self-tapping phillips pan head screw - blackzinc140.216" ID x 0.512" OD x 3/64" Washer Steel Black (#10)Stellar GL - Cap - Axle plate 20" 24"78G2 - Lower Frame - Weldment12019# 8 x 3/8" self-tapping phillips pan head screw6G2 - Lower Frame - Mounting Bracket Shim55557B/S Axle Plate Assembly (20"/22"/24" Wheel) (LH/RH)51212432B/S Axle Plate Assembly (20"/22"/24" Wheel) (RH/LH)4131211555558Stellar GL - Cap - Lower Frame - Front Cap (RH/LH)61479ECO#Sheet2 of 2Date of Issue2015 June 02Revision0Bahareh AshtianiFile name (Drawing #)Status55760NA22142622211121Short - withoutTie Downs/QTY.Approved by1600355765557611206755576555765555912192Caster & Fork Assembly355559Number25Stellar GL - Cap - Lower Frame - Front Cap (LH/RH)Part Name or Description1041Item12See configurationSee 85002for setupPDG part number93Printed: July-08-15 Created: December-16-10 11:21:26 AM Saved: July-08-15 4:14:10 PM By: jformby Checked Date: 2015 Feb 04Dimensioning and Tolerancing Standard ASME Y14.5-20090RevFile : 55760 R: 0DCBA
Page 14 of 331462123R3/8-16 Nylon Locknut - Thick - Black ZincOil Lite Bushing - Flanged - 1/2" ID x 5/8" OD x 1/2" LSpring - Wave Disc - 0.650" ID x 0.855" OD x 0.060" Height5/16-18 (2B) Nylon Locknut - Thick - Black Zinc34565572155780557445574416 G2 - Bentley - Sub-Frame - Assembly17 G2 - Common Upper Frame Assembly18 G2 - Bentley/Stellar - Upper Frame - Pivot Plate (LH/RH)19 G2 - Bentley/Stellar - Upper Frame - Pivot Plate (RH/LH)Tolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmTorr Brown5576015 G2 - Lower Frame Assembly1111122114444422621Sheet1 of 1Date of Issue2015 June 09Revision0Bahareh AshtianiFile name (Drawing #)Status55720NAApproved byCUS: [20620]1202814 1/4" ID x 5/8" OD x 3/64" Washer - Steel - Black ZincRevised by1222313 1/4 - 20 Nylon Locknut - Thick - Black ZincTechnical reference1241412 5/16" x 2-1/4" x 1/4-20 Socket Head Shoulder Bolt - Black Zinc1202911 5/16" x 2 1/2" x 1/4-20 Socket Head Shoulder Bolt - Black umber QTY1479126393/8" ID x 3/4" OD x 3/64" Washer Steel Black96ECO#10 5/16-18 x 7/8 L Flat Head Screw3/8-16 x 1" Hex Head Bolt85/16" ID x 11/16" OD x 1/16" Washer - Black Zinc1/2" x 1/2" x 3/8-16 Socket Head Shoulder Bolt - Black Zinc27Bentley Gas Strut and Spring Assembly51Torr BrownTorr BrownTitle:G2 - Bentley Chair Frame AssemblyAuthor829351119104Item Part Name or Description 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNAPDG part number17SeeconfigurationNotes:1. Material: As per detailed part2. Remove burrs & sharp edges.3. Finish : As per detailed part4. Component weight [grams]: 18961.745. All holes are through unless otherwise specified6. Dimensional limits apply before coating.16SeeconfigurationSee 85055for setupInitial ReleaseRevision description15Seeconfiguration41187131Printed: July-08-15 Created: October-23-14 2:53:09 PM Saved: July-08-15 4:15:40 PM By: jformby Checked Date: 2015 Mar 04Dimensioning and Tolerancing Standard ASME Y14.5-20090RevFile : 55720 R: 0DCBA
Page 15 of 3376102111Dimensioning and Tolerancing Standard ASME 20212223Author56ECO#Technical referenceTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmVinh TranRevised bySheet1 of 1Date of Issue2015 June 09Approved byTorr BrownFile name (Drawing #)55730Revision0StatusNANotes:1. Material: As per detailed part2. Remove burrs & sharp edges.3. Finish : See purchase order4. Component weight [grams]: 18518.825. All holes are through unless otherwise specified6. Dimensional limits apply before coating.7. General tolerance of 0.15 mm.CUS: [20615]1479Part Name or DescriptionNumber QTYG2 - Lower Frame Assembly557601Stellar GL - Gas Strut Assembly555771G2 - Common Upper Frame Assembly557801G2 - Stellar GL - Sub-Frame - Assembly5573111/2" x 1/2" x 3/8-16 Socket Head Shoulder Bolt - Black Zinc122412Oil Lite Bushing - Flanged - 1/2" ID x 5/8" OD x 1/2" L123982G2 - Stellar GL - Upper Frame - Pivot Plate (LH/RH)5573413/8" ID x 3/4" OD x 3/64" Washer Steel Black1202843/8-16 x 1" Hex Head Bolt124084Spring - Wave Disc - 0.650" ID x 0.855" OD x 0.060" Height1248023/8-16 Nylon Locknut - Thick - Black Zinc1202165/16-18 x 7/8 L Flat Head Screw126394G2 - Stellar GL - Upper Frame - Pivot Plate (RH/LH)5573415/16-18 (2B) Nylon Locknut - Thick - Black Zinc1201045/16" ID x 11/16" OD x 1/16" Washer - Black Zinc120134Stellar GL - Tilt Limiting Bumper5556911/4-20 x 5/8" flat head cap screw - Black Zinc1201425/16" x 2 1/2" x 1/4-20 Socket Head Shoulder Bolt - Black Zinc 1202921/4" ID x 5/8" OD x 3/64" Washer - Steel - Black Zinc1202815/16" ID x 1/2" OD x I/8" Black Nylon Spacer122272G2 - Stellar GL Sub Frame - Tilt Limiting Sleeve5573511/4" x 2.5" Quick Release Pin - Ring Grip1241711/4-20 Nylon Locknut - Thin - Black Zinc1203724Bahareh AshtianiBahareh AshtianiTitle:G2 - Stellar GL Chair Frame AssemblySee configurationSee 85040for setup 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityPDG part number1719232See configuration312143161521320Initial ReleaseRevision description22181Printed: July-08-15 Created: October-23-14 2:53:09 PM Saved: July-08-15 4:21:40 PM By: jformby Checked Date: YYYY/MMM/DD4See 85055for setup0RevFile : 55730 R: 0DCBA
Page 16 of 33181713151114See configuration192016Initial ReleaseRevision description210NA 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityR125121222619 5/16" ID x 1/2" OD x 1/16" Black Nylon Spacer20 1/4"ID x 1/2"OD x 0.06T Nylon WasherTolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmVinh TranSheet1 of 1Date of Issue2015 June 091122114424Revision0StatusNA1222718 5/16" ID x 1/2" OD x I/8" Black Nylon SpacerTorr BrownFile name (Drawing #)557401222317 1/4 - 20 Nylon Locknut - Thick - Black ZincApproved by1307416 Tilt Limter AssemblyRevised by5574415 G2 - Bentley/Stellar - Upper Frame - Pivot Plate (RH/LH)Technical reference1201314 5/16" ID x 11/16" OD x 1/16" Washer - Black ZincBahareh AshtianiJim FormbyTitle:G2 - Stellar Chair Frame AssemblyAuthor1201013 5/16-18 (2B) Nylon Locknut - Thick - Black Zinc124801240812 Spring - Wave Disc - 0.650" ID x 0.855" OD x 0.060" Height11 3/8-16 x 1" Hex Head 574155760Number QTY1479120215/16-18 x 7/8 L Flat Head Screw96ECO#10 3/8-16 Nylon Locknut - Thick - Black ZincG2 - Bentley/Stellar - Upper Frame - Pivot Plate (LH/RH)811Oil Lite Bushing - Flanged - 1/2" ID x 5/8" OD x 1/2" L765/16" x 3-1/2" x 1/4-20 Socket Head Shoulder Bolt - Black Zinc1/2" x 1/2" x 3/8-16 Socket Head Shoulder Bolt - Black ZincStellar Gas Strut and Spring Assembly5645122See configurationSee 85055 for setupPDG part number7G2 - Common Upper Frame Assembly35G2 - Stellar - Sub-Frame - Assembly2See 85006 for setupG2 - Lower Frame Assembly1Item Part Name or Description44893See configuration3Printed: July-08-15 Created: October-23-14 2:53:09 PM Saved: July-08-15 4:24:42 PM By: jformby Checked Date: 2015 Mar 19Dimensioning and Tolerancing Standard ASME Y14.5-20090RevFile : 55740 R: 0DCBA
Page 17 of 33116"17"Width19"20"R21"22"8765432121Approved 3776554388877668888876Author8888888Torr BrownTechnical reference5UnitsmmJim Formby8763Sheet1 of 1Date of Issue2016 June 30Torr BrownFile name (Drawing #)850064LIGHTERRevised byHEAVIERTolerances unless otherwise stated:Angular: /- 1ºOther x /-0.8, x.x /-0.4, x.xx /-0.15Jim FormbyTitle:Stellar - Tilt Configuration8888887 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityPDG part numberNA887665518"Revision3StatusNACUS: [ ]15265Updated Setup Table4ECO#3Revision description2Printed: July-08-16 Created: March-16-15 2:47:05 PM Saved: July-08-16 1:29:49 PM By: jformby Checked Date: 2015 July 08Dimensioning and Tolerancing Standard ASME Y14.5-20093RevFile : 85006 R: 3DepthDCBA
Bentley / Stellar ChartsTrigger Cable and Tilt Limiter SetupTrigger Cable SelectionCable49"When to Use25" Back Post59"31" Tall Back PostNote 1:Dual activator Cable is not compatible with 31” high Back FrameNote 2: Pre-adjust cable to ½” from edge.D2520Degreeg es30rD eese35 grD eese40 greeDeg s45reeDeg sreesTilt Limiter (Stellar Only)Note: Move shoulder bolt to set tilt limit degrees specified in the Work Order.Chair may not tilt exactly at required angle.Page 18 of 33
12-5 to 40DEFAULT 0 to 4534Uplift ForceTilt Range Adjustment *RAuthorTolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15Technical referenceTorr BrownJim FormbyTitle:Stellar GL - Tilt Configuration 2010 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityPDG part number* Tilt Range values are 2 deg.** HD position will result in reduced tilt range.TILT AND GAS STRUT ADJUSTMENTHD (200 - 250) **LD (100 - 150)RD (150 - 200) DEFAULTNA-5 to 50Modified for new Stellar GL FrameRevision descriptionPrinted: Wednesday, July 08, 2015 Created: Monday, January 10, 2011 5:35:09 PM Saved: Monday, July 06, 2015 9:37:11 AM By: vtran Checked Date: -Dimensioning and Tolerancing Standard ASME Y14.5-20092RevFile : 85040 R: 2{Page 19 of 33Units[mm]Revised byJim FormbySheet1 of 1Date of Issue2015 Mar 16Approved byTL 20TL 10TL 30TL 40TL 50Torr BrownFile name (Drawing #)85040Tilt Limiter56Revision2StatusNA1477ECO#DCBA
Page 20 of 33123R2318"34419"56Tolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15Units[mm]Revised by* Large Seat Pan Required2Technical reference1ReferencePosition117"0520"7Back Post Tube Position5Sheet1 of 1Date of Issue2015 Mar 1166*Revision3StatusNACUS: [ ]1477ECO#22"Approved by5*21"Torr BrownCaitlin LukowJim FormbyTorr BrownTitle:File name (Drawing #)85008Bentley/Stellar/Stellar GL - Seat Depth/ Back Angle Setup ChartAuthor16"4Seat Depth 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNA1141229098106PDG part numberBack Rest Angle SetupReference HoleUpper FrameModified for common upper frameRevision descriptionPrinted: Wednesday, July 08, 2015 Created: Wednesday, March 20, 2013 2:32:05 PM Saved: Wednesday, July 08, 2015 4:44:48 PM By: vtran Checked Date: 2015 Mar 11Dimensioning and Tolerancing Standard ASME Y14.5-20093RevFile : 85008 R: 3DCBA
Page 21 of 335917162See config8Initial ReleaseRevision rances unless otherwise stated:Angular: /- 1ºOther: x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmVinh TranRevised bySheet1 of 2Date of Issue2015 July 08Torr BrownFile name (Drawing #)55639Approved by1" OD x 1/2" ID x 5/8" Long Urethane Tube Bushing1/4-20 Nylon Locknut - Thick Black Zinc5/16" ID x 11/16" OD x 1/16"Washer - Black Zinc5/16"-18 x 2" Socket HeadCap Screw5/16-18 (2B) Nylon Locknut Thick - Black Zinc1/4" ID x 5/8" OD x 3/64"Washer - Steel - Black ZincOil Lite Bushing - 1/4" ID x 3/8"OD x 1" LBentley/Stellar AngleAdjustable Push Bar - LowerTube - Tall1/4-20 x 1-1/2" with 1-1/8"Shoulder - Button Head BoltG2 - Common Upper FrameAssemblyTechnical reference120537Torr BrownJim FormbyTitle:G2 - Bentley/Stellar Back Post InstallationAuthor10See TEM NO. 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityN/APDG part number3Printed: Thursday, July 09, 2015 Created: Wednesday, October 14, 2009 5:33:30 PM Saved: Thursday, July 09, 2015 10:51:46 AM By: vtran Checked Date: 2015 July 08Dimensioning and Tolerancing Standard ASME Y14.5-20090RevFile : 55639 R: 06Revision0StatusN/ACUS: [13021]1222422422DCBDefault/QTY.A1479ECO#
Page 22 of 331114856122103See config7Initial ReleaseRevision descriptionRTolerances unless otherwise stated:Angular: /- 1ºOther: x /-0.8, x.x /-0.4, x.xx /-0.15UnitsmmVinh TranSheet2 of 2Date of Issue2015 July 08Torr BrownFile name (Drawing #)55639Approved byRevision0StatusN/ACUS: [13021]23/4" OD x 0.17" Wire x 1-3/4" Long- Coil Die SpringRevised by2122245/16"-18 X 3-1/2" Socket HeadCap Screw1/4-20 x 1-1/2" with 1-1/8"Shoulder - Button Head BoltG2 - Common Upper FrameAssemblyBentley/Stellar Angle AdjustablePush Bar - Lower Tube - Tall1/4" ID x 5/8" OD x 3/64" Washer Steel - Black ZincOil Lite Bushing - 1/4" ID x 3/8" ODx 1" L2421/4-20 Nylon Locknut - Thick Black Zinc5/16" ID x 11/16" OD x 1/16"Washer - Black Zinc5/16-18 (2B) Nylon Locknut - Thick- Black Zinc214791" OD x 1/2" ID x 5/8" Long Urethane Tube BushingTorr BrownJim FormbyTitle:G2 - Bentley/Stellar Back Post Technical 046120133120281200325551661 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityN/APDG part number4ITEM NUMBER9See config3Printed: Thursday, July 09, 2015 Created: Wednesday, October 14, 2009 5:33:30 PM Saved: Thursday, July 09, 2015 10:51:46 AM By: vtran Checked Date: 2015 July 08Dimensioning and Tolerancing Standard ASME Y14.5-20090RevFile : 55639 R: 0DCBA
Page 23 of 332341098765432112386 Cable ClipR 2010 The informationcontained in this drawingis the sole property ofPDG Mobility12052 Cable - Trigger End2114112282QTY.3136905 07, 20133See Configuration75135903 27, 2013Description:Bentley/Stellar Angle Adjustable Back Post AssemblyTBMJApproved6Drawing #13022Date of IssueAug 5, 2011AuthorJF9104ApprovedWSRevision36Where possibleDo not install triggerover foam grip.8See ConfigurationECO5DateAssembly Notes:Item 1 should be sprayed with hair spray to lubricate.12069 Angle adjustable hinge8 x 5/8 self-tapping phillips pan12068 #head screw12056 Trigger assemblyOD x 0.937" Long Standoff for12145 1/4"Push HandleAngle Adjustable Push55013 Bentley/StellarBar - Upper TubeDESCRIPTION12350 6.5" Foam Grip for Push BarSocket Button Head 12144 10-32x1/2"Black ZincAngle Adjustable Push55210 Bentley/StellarBar - Lower TubeITEM NUMBER21REV REVISION DESCRIPTIONthe angle adjustable hinge's button on inside, use 6.5" foam grip2 Mountinstead of 8" and add note for item 63 Mount the angle adjustable hinge's button on outside1DCBA
Page 24 of 33Initial ReleaseRevision descriptionDual Post Armrest - Bolt on - Assembly (RH/LH)5/16-18 x 5/8" Socket Button Head - Black Zinc45RAuthor411413245321T-Style Armrest5Tolerances unless otherwise stated:Angular: /- 1ºOthe x /-0.8, x.x /-0.4, x.xx /-0.15Technical referenceUnitsmmRevised byG2 - Common Upper Frame AssemblyT-Style Armrest and Clothing Guard Assembly(RH/LH)T-Style Armrest and Clothing Guard Assembly(LH/RH)5/16-18 x 1-1/4" Socket Button Head - Black Zinc5/16-18 Nylon Locknut - Thin - Black ZincItem Part Name or Description15424Sheet1 of 161477ECO#44111Date of Issue2015 Jul 08Approved by12062120663632736327557803Revision0StatusNACUS: [ ]Number T-Style/QTY.Torr BrownJim FormbyJim FormbyTorr BrownTitle:File name (Drawing #)55636Bentley/Stellar/GL G2 - Armrest Attachment Assembly1250436382363821206655780Number QTY3 2013 The information Third angle projectioncontained in this drawingis the sole property ofPDG MobilityNADual Post Armrest - Bolt on - Assembly (LH/RH)3PDG pa
Dimensioning and Tolerancing Standard ASME Y14.5-2009 Bahareh Ashtiani Keira Lane Torr Brown 1 Updated to include Bentley Extended Seat To Floor 1534 Title: 2016 Sept 7 mm 1 of 3 NA 1 Taco Tuesday - B/S/GL Chair Seat Height Adjustment Chart Angular: /- 1º Othe x /-0.8, x.x /-0.4, x.xx /-0.15 Author 85055 NA Bahareh Ashtiani
