Transcription
OWNER’S MANUALB-500-EXT-230-RSHDBaseT EXTENDER
B-500-EXT-230-RS Installation and Users ManualIMPORTANT SAFETY INSTRUCTIONSWARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.1. Read and follow all instructions and warnings in this manual. Keep for future reference.2. Do not use this apparatus near water.3. Clean only with a dry cloth.4. Do not block any ventilation openings. Install according to manufacturer’s instructions.5. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus(including amplifiers) that produce heat.6. Do not override the safety purpose of the polarized or grounding-type plug. A polarized plug hastwo blades - one wider than the other. A grounding type plug has two blades and a third groundingprong. The wide blade or the third prong is provided for your safety. If the provided plug does not fitinto your outlet, consult an electrician for replacement of the obsolete outlet.7. Protect the power cord from being walked on or pinched particularly at plug, conveniencereceptacles, and the point where it exits from the apparatus.8. Only use attachments/accessories specified by the manufacturer.9. Refer all servicing to qualified service personnel. Servicing is required when the apparatus hasbeen damaged in any way, such as when the power-supply cord or plug is damaged, liquid hasbeen spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain ormoisture, does not operate normally, or has been dropped.10. DO NOT EXPOSE THIS EQUIPMENT TO DRIPPING OR SPLASHING AND ENSURE THAT NO OBJECTSFILLED WITH LIQUIDS, SUCH AS VASES, ARE PLACED ON THE EQUIPMENT.11. TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS, DISCONNECT THE POWERSUPPLY CORD PLUG FROM THE AC RECEPTACLE.12. THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE.CAUTION: TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER.NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICEPERSONNEL.The lightning flash with arrowhead symbol, within an equilateral triangle,is intended to alert the user to the presence of un-insulated dangerousvoltage within the product’s enclosure that may be of sufficient magnitudeto constitute a risk of electric shock to persons.The exclamation point within an equilateral triangle is intended to alert theuser to the presence of important operating and maintenance (servicing)instructions in the literature accompanying the appliance.pg.2
B-500-EXT-230-RS Installation and Users ManualTABLE OF CONTENTS1. Overview. 42. Package Contents. 43. Features. 54. Connections and Controls. 64.1. B-500-EXT-230-RS Transmitter.64.2. B-500-EXT-230-RS Receiver.75. Basic Connections. 85.1. HDBaseT Link (RJ45) Connection.85.2. IR Control Connections.95.2.1. IR Control In (3.5mm {1/8”} Mono) - Transmitter.105.2.2. IR Receiver In (3.5mm {1/8”} Stereo) - Receiver.105.2.3. IR Flasher Out (3.5mm {1/8”} Mono) – Transmitter and Receiver.115.3. RS232 Control Connections.115.3.1. RS232 Control (DB9) Connection.115.4. HDMI Out to Display (HDMI).125.5. Latch Locking Power Supply.126. Installation. 136.1. B-500-EXT-230-RS Transmitter Installation.136.2. B-500-EXT-230-RS Receiver Installation.137. Specifications. 148. WARRANTY. 159. Contacting Technical Support. 15 2012 Binarypg.3
B-500-EXT-230-RS Installation and Users Manual1. OVERVIEWThe B-500-EXT-230-RS extends HDMI over single Cat5e/6 using HDBaseT technology allowing videoand audio transmission to remote displays. In addition, the B-500-EXT-230-RS is equipped with bidirectional IR pass-through and bi-directional RS-232 pass-through all over a single Cat5e/6 cable.Supports all HDMI defined Audio and Video formats, including 3D Video.The Power Over Cable feature requires only one end of the link to be powered.2. PACKAGE CONTENTS(1) B-500-EXT-230-RS Transmitter(1) B-500-EXT-230-RS Receiver(1) 24V DC 1A Power Supply(4) Mounting Screws(8) Rubber Feet(1) User Manual(1) IR Adapter Cablepg.4
B-500-EXT-230-RS Installation and Users Manual3. FEATURESForm and Function Wall-Mountable Housing Design for Easy Installation Extends all HDMI formats up to 4Kx2K via a Single cableCat5eUp to 200ftCat6/Cat6aUp to 230ft Transmits HDMI Signal via HDBaseT up to 10.2Gbps HDCP 1.2 Compliant Power Over Cable (POC) Allows for Single Power Supply Latch Locking Power SupplyVideo 2D Resolutions up to 1080p@60Hz – 48 Bit; including Deep Color 4Kx2K 3D Resolutions up to 1080p@24Hz – 48 Bit; including Deep Color EDIDs Read from Connected Display to SourceAudio Supports all HDMI supported Audio Formats, including DTS-HD Master and Dolby TrueHDControl Functionality Bi-Directional IR Pass-Through- Supports IR Signal from 20kHz To 60kHz- Adaptive IR Input Levels (3.5V DC To 12V DC) Bi-Directional RS232 Up to 115.2 Kb/s 2012 Binarypg.5
B-500-EXT-230-RS Installation and Users Manual4. CONNECTIONS AND CONTROLS4.1. B-500-EXT-230-RS Transmitter12345 24V DC 1AINPUT67DTEDCE118ON5SERVICERS-23293222ONONPWRHDMI INControl InDCEDTEHDBaseTHDBaseTLINKLINK1. Latch-Locking Power JackConnect to the included 24V DC 1A Power Supply.2. Power LEDIndicates current state of Power; illuminates RED when power is applied.3. HDMI In (HDMI)Connect an HDMI cable to the HDMI output of a source, AV Receiver, HDMI Splitter, or HDMISwitcher/Matrix.4. IR Flasher Out (3.5mm {1/8”} Mono)Connect an IR flasher to use IR signals sent from the remote location.5. IR Control In (3.5mm {1/8”} Mono) Connect the IR output of an Automation System or IR connecting block to send IR signals to the remotelocation. To simplify connection to most Automation Systems, this port does not supply power.6. RS232 Operation Mode Dip SwitchesSwitch 1: Configures RS232 DB9 connection pins for DCE or DTE communication.Switch 2: Configures RS232 DB9 connection: ON for Pass-Through (normal operation) or SERVICEfor Firmware update.See section 5.3.1.1 RS232 Operation Mode.7. RS232 Control (DB9)Connect to an Automation System RS232 control port to send RS232 signal to the Receiver.8. HDBaseT Link to Receiver (RJ45)Connect to HDBaseT RJ45 on Receiver; this connection follows standard TIA/EIA-568B.9. Signal Link LEDIndicates link status with Receiver; illuminates GREEN when sync is present. Blinks when in LowPower Mode.pg.6
B-500-EXT-230-RS Installation and Users Manual4.2. B-500-EXT-230-RS Receiver12345 24V DC 1AINPUT67DTEDCEONONPWRHDMI OUTDCEDTE118ON5SERVICERS-23293222HDBaseTLINK1. Latch-Locking Power JackConnect to the included 24V DC 1A Power Supply.2. Power LEDIndicates current state of Power; illuminates RED when power is applied.3. HDMI Out to Display(HDMI)Connect an HDMI cable to the HDMI In of the display or AV Receiver.4. IR Flasher Out (3.5mm {1/8”} Mono)Connect an IR Flasher to transmit IR signals sent from the remote location.5. IR Receiver In (3.5mm {1/8”} Stereo) Connect an IR Receiver to send IR signals to the Transmitter from the remote location. Includes 9V to power IR Receiver.6. RS232 Operation Mode Dip SwitchesSwitch 1: Configures RS232 DB9 connection pins for DCE or DTE communication.Switch 2: Configures RS232 DB9 connection: ON for Pass-Through (normal operation) orSERVICE for Firmware update.See section 5.3.1.1 RS232 Operation Mode.7. RS232 Control (DB9)Connect to an Automation System RS232 control port to send RS232 signal to the Transmitter.8. HDBaseT Link to Transmitter (RJ45)Connect to HDBaseT RJ45 on Transmitter; this connection follows standard TIA/EIA-568B.9. Signal Link LEDIndicates link status with Transmitter; illuminates GREEN when sync is present. Blinks when inLow Power Mode. 2012 Binarypg.7
B-500-EXT-230-RS Installation and Users Manual5. BASIC CONNECTIONSB-100-HDMATRIX-8x8 or HDMI SourceIR Receiver12V DC 5AINPUTACPowerINPUT 1Engineered in the USAManufactured in TaiwanRS-232 Pin OutPIN SIGNAL2 Transmit Data3 Receive Data5 Signal GroundRS-232ETHERNETINPUT 2INPUT 3INPUT 4INPUT 5INPUT 6INPUT 7INPUT 8OUTPUT 1OUTPUT 2OUTPUT 3OUTPUT 4OUTPUT 5OUTPUT 6OUTPUT 7OUTPUT 8B-500-EXT-230-RS Transmitter 24V DC N55SERVICESERVICERS-232RS-23233 2222ONONPWRHDMI INPWRHDMI OUTControl InDCEDTE 24V DC 1AINPUTDCEDTE11HDBaseTLINKHDBaseTHDBaseTLINKLINK33 2222ONONDCEDTEB-500-EXT-230-RS ReceiverHDTVNote: When a power supply is connected to either the Transmitter or Receiver, theHDBaseT link sends power to the other unit. Only 1 unit requires a power supply beconnected.5.1. HDBaseT Link (RJ45) ConnectionConnection Precautions!The B-500-EXT-230-RS is specified to operate with Cat5e/Cat6/Cat6a cables for communicationbetween the Transmitter and Receiver. The transmission path may include Keystones and PatchCables as long as the total length does not exceed 200ft for Cat5e and 230ft for Cat6/Cat6a.Note: The HDBaseT Link RJ45 connection includes a 24V signal. DO NOT connect anything into thisport other than an HDBaseT Transmitter or Receiver.TIA/EIA Standard 568-B (Gold Pins Facing Up)Pin 1Pin 2Pin 3Pin 4pg.8White/OrangeOrangeWhite/GreenBluePin 5Pin 6Pin 7Pin 8White/BlueGreenWhite/BrownBrown
B-500-EXT-230-RS Installation and Users Manual5.2. IR Control ConnectionsBi-directional IR signals are transmitted between the B-500-EXT-230-RS Transmitter and Receiverover the Cat5e/6 cable. How the IR connections function varies on the Transmitter and Receiverbased on the common use cases for sending and receiving IR. This section outlines the operationof IR on the Transmitter and Receiver.HDMI SourcePLAYIR Processor / ControllerIR InputsIR Outputsor 24V DC 1AINPUTACONONDCEDTE1ONHDMI INPWRControl In125 5 -232D32 24V DC rHDBaseTPWRLINKLINKHDMI OUTCBHDTVNote: Arrow Direction Indicates Signal FlowA IR Control In (3.5mm {1/8”} Mono) -See Section 5.2.1B IR Receiver In (3.5mm {1/8”} Stereo)-See Section 5.2.2C IR Flasher Out (3.5mm {1/8”} Mono)-See Section 5.2.3D HDBaseT Link Cat5e/Cat6/Cat6a (RJ45)-See Section 5.1Connection Precautions! Before connecting an IR Receiver or an IR Automation System, verify that the B-500EXT-230-RS is OFF to avoid damaging the unit. The IR Receiver In (3.5mm {1/8”} Stereo) on the Receiver provides 9V power to powerIR Receivers. This voltage can damage flashers and Automation Systems. Take cautionbefore plugging an IR Flasher or IR Receiver into the respective IR sockets. TheManufacturer’s Warranty will not cover any damage that may occur. See IR ControlConnections section for proper cabling. Pin out configurations for IR Receivers and Automation Systems vary. Beforeconnecting to this input, review this section carefully in order to match the pin outs forthe B-500-EXT-230-RS. 2012 Binarypg.9
B-500-EXT-230-RS Installation and Users Manual5.2.1. IR Control In (3.5mm {1/8”} Mono) – Transmitter OnlyThe most common use of the IR Control In port is to send a wired IR signal from an AutomationSystem to an IR Flasher connected to the Receiver. This connection does not include power for anIR Receiver. A 3.5mm {1/8”} Mono Cable is used to connect directly to the Automation System IRoutput or Connecting Block.GND (Sleeve)IR Signal (Tip)IR SignalTipGND (Gro und)RingIf the system requires a powered IR Receiver at the Transmitter, a powered IR Block will be neededbetween the IR Receiver and the Transmitters IR Control In.5.2.2. IR Receiver In (3.5mm {1/8”} Stereo) – Receiver OnlyThe most common use of the IR Receiver port is to send an IR signal from a powered IR Receiverto an IR Flasher connected to the Transmitter. This connection includes 9V DC power for anIR Receiver. A 3.5mm {1/8”} Stereo Cable is used to connect directly to an IR Receiver, DO NOTconnect a mono cable to this connection as damage may occur.9V DC (Sleeve)GND (Ring)IR Signal (Tip)IR SignalTipGND (Gro und)Ring 9V DCSleeveIf the system requires connection to an Automation System or Connecting Block to send IR to theTransmitter, the included IR Adapter Cable between the Automation System or Connecting Blockoutput and the IR Receiver input must be used.To IR Receiver In9V DC (Sleeve)GND (Ring)IR Signal (Tip)pg.10To IR Control Systemor Connecting BlockGND (Sleeve)IR Signal (Tip)
B-500-EXT-230-RS Installation and Users Manual5.2.3. IR Flasher Out (3.5mm {1/8”} Mono) – Transmitter and ReceiverGND (Sleeve)IR Signal (Tip)IR SignalTipGND (Gro und)Ring5.3. RS232 Control ConnectionsBi-directional RS232 signals are transmitted between the B-500-EXT-230-RS Transmitter andReceiver over the Cat5e/6 cable. The Transmitter may be connected to an Automation Systemcontroller and the Receiver connected to an RS232 controllable device.B-500-EXT-230-RSTransmitterDCEDTEONON1 155 33 S-232HDBaseTLINK1 2A2ONDCEDTEAutomationSystem55 33 232HDBaseTHDBaseTLINKLINKRS232 ControllableDeviceA RS232 Control (DB9)-See Section 5.3.1B HDBaseT Link Cat5e/Cat6/Cat6a (RJ45)-See Section 5.15.3.1. RS232 Control (DB9) ConnectionTo eliminate the need to make cross over or ‘null modem’ cables, the RS232 pin outs can beconfigured for DCE or DTE. Set Switch 1 to DCE (Up) if the connected device is DCE, and to DTE(Down) if the connected device is DTE.Typically the Automation System will be DTE and the controlled device will be DCE, however,devices may vary. Refer to the manual for the connected devices for proper pin-out configuration.DCERS232 DB9 Pin Outs53 2DCEON121ONDTEDCE (Up)PIN 2012 Binary2ONSERVICEDTEONFUNCTIONSERVICEDTE (Down)PINFUNCTION2RxD (Data Receive)2TxD (Data Transmit)3TxD (Data Transmit)3RxD (Data Receive)5GND5GNDpg.11
B-500-EXT-230-RS Installation and Users Manual5.3.1.1 RS232 Operation ModeThe RS232 connection is used for performing Firmware updates in addition to sending RS232signals. Switch 2 is used to set the RS232 Mode.Note: Switch 2 must set to ON (Up) during normal RS232 Pass-Through operation.DCEON1122ONONDTEONDCESERVICERS232 Pass-Through(Up)DTESERVICEService(Down)5.3.1.2. Firmware Update OperationAs new source and display devices become available, it may be necessary to modify the firmwarein the B-500-EXT-230-RS. To perform firmware updates, the dipswitches must be set to DTE(Down) and Service. Detailed instructions and updated firmware will be posted to www.snapav.com as they are released.5.4. HDMI Out to Display (HDMI)Connection Precautions! We recommend using a 1 meter or shorter HDMI cable to connect the B-500-EXT-230-RS to thedisplay; this will ensure the highest quality image on the display.5.5. Latch Locking Power SupplyWith Power Over Cable (POC), power is not required at both ends of the installation. When apower supply is connected to either the Transmitter or Receiver, the HDBaseT link sends power tothe other unit. Only 1 unit requires a power supply be connected.pg.12
B-500-EXT-230-RS Installation and Users Manual6. INSTALLATIONNote: DO NOT connect power to the B-500-EXT-230-RS until all other connections are made and theunit is installed.6.1. B-500-EXT-230-RS Transmitter Installation1. Run the Cat5e/Cat6/Cat6a cable from the location of the Transmitter to the remote location ofthe Receiver.2. Mount the B-500-EXT-230-RS Transmitter in the desired location.3. Connect the HDMI Out of a source component using an HDMI cable.4. Connect the RS232 DB9 from an Automation System if being used.5. Connect an IR Control System to the IR Control In and/or IR Flasher if being used.6. Connect the Cat5e/6 cable to the B-500-EXT-230-RS Transmitter.7. Connect the 24V DC 1A Power Supply to the Latch-Locking Power Jack, unless POC is beingused to send power from the Receiver. DO NOT plug the power supply into an AC outlet untilStep 9 under Receiver Installation.6.2. B-500-EXT-230-RS Receiver Installation1. Run the Cat5e/Cat6/Cat6a cable from the location of the Transmitter to the remote location ofthe Receiver.2. Install the B-500-EXT-230-RS Transmitter following the steps outlined in section 6.1. B-500-EXT230-RS Transmitter Installation.3. Mount the B-500-EXT-230-RS Receiver in the desired location.4. Connect the Cat5e/6 cable to the B-500-EXT-230-RS Receiver.5. Connect an IR Flasher and/or IR Receiver if being used.6. Connect an HDMI cable from the B-500-EXT-230-RS to the display.7. Connect the RS232 DB9 to an RS232 controllable source if being used.8. Connect the 24V DC 1A Power Supply to the Latch-Locking Power Jack, unless POC is beingused to send power from the Transmitter.9. Plug the power supply for either the Transmitter or the Receiver (depending on which unit issupplying power) into an AC outlet. 2012 Binarypg.13
B-500-EXT-230-RS Installation and Users Manual7. SPECIFICATIONSTechnicalTransmitterHDMI ComplianceHDMI 3DHDCP ComplianceYesVideo Bandwidth10.2GbpsHDMI over UTP TransmissionReceiverResolutionCat5eCat6/Cat6a1080i / 720p24-bit color200ft230ftFull HD 1080P24-bit color200ft230ftFull HD 1080P36-bit deepcolor200ft230ftInput TMDS Signal1.2 Volts (peak-to-peak)Input DDC Signal5 Volts (peak-to-peak, TTL)ESD Protection(1) Human body model — 15kV (air-gap discharge) & 8kV (contact discharge) (2) Core chipset — 8kVIR Signal (Bi-directional)Carrier frequency: 20-60kHzConnectionsHDBaseT Link1x RJ451x RJ45HDMI1x HDMI Type A(19-pin female)1x HDMI Type A(19-pin female)IR Receiver (In)---1x 3.5mm StereoIR Control In1x 3.5mmMono---IR Flasher (Out)1x 3.5mmMono1x 3.5mmMonoRS232 ontrolsDipswitch 1RS232 Pin Configuration (DCE or DTE)Dipswitch 2RS232 Operation Mode (Pass-Through or FirmwareUpdate)MechanicalHousingMetal enclosureDimensions6.25”x3.1”x1.3”Weight1.1 lbs.Power Supply24V DC 1APower Consumption12 watt (max)Operation Temperature32 104 FStorage Temperature-4 1
instructions in the literature accompanying the appliance. 2012 Binary B-500-EXT-230-RS Installation and Users Manual . Configures RS232 DB9 connection pins for DCE or DTE communication. Switch 2: Configures RS232 DB9 connection: ON for Pass-Through (normal operation) or SERVICE . Manufacturer’s
