Transcription
Sadoun PowerTechDIGITAL
INSTALLING THE MOUNT1. Assemble the H-H Mount as the following diagram.2. Ensure the mounting tube indicates 0 . If not, sit it to exactly 0 using the manual buttons on thebottom of the mount. The cable must be connected to the receiver which must be switched on.3. Make sure the mounting pole is exactly vertical before installation.4. Fix the H-H Mount onto the Mounting pole or stand and tighten the two U-bolts evenly. Makesure there is no obstacle facing the southern sky, such as a tree or building.Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95951
ALIGNMENT OF THE MOUNT1. Finding TRUE SOUTH.Attaching the Antenna Dish to the Mount. Make sure the dish is at the center of the mounting tube.Rotate the mount together with the antenna toward TRUE SOUTH. You can find the TRUESOUTH using the magnetic variation table and a compass that indicates the MAGNETIC SOUTH.2. Setting Elevation Angle.(A)Adjust the motor elevation angle using an inclinoneter or the Latitude scale on one sides of theMotor according to the Latitude of your position.3. Setting Declination Angle.(B) Find the Declination Angle on the attached ANGLE TABLE. Set the Declination Angle by the scale on the antenna dish. The reading on the antenna scaleshould be: 35 -DECLINATION ANGLE4. Drive the antenna east and west via the manual buttons on the bottom of the Mount to check ifthe reception arc is correct. If not, adjust the direction, elevation, and declination angle to find thebest reception.P.S. To ensure power to drive the antenna, first connect the Mount to the receiver or interface boxvia coaxial cable.Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95952
ADJUST THE TUBE LOOSEIf you incur the problem of loose tube, follow the procedure to solve it:1.Loosen the 4 screws (#1 on the picture) a little2.Tighten the screw (#2 on the picture) a little.3.Tighten the 4 screws (#1 on the picture) securelyCABLE CONNECTIONConnect the DiSEqC Mount and the coaxial cable (RG-6/U) per the following diagram.Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95953
DiSEqC 1.2 OPERATIONThe DISEqC Motor is designed for DiSEqC 1.2 Receiver. The commands of the receivers might bedifferent, but similar. Please refer to the manual of the DiSEqC 1.2 receiver.1.Go East / West: Rotates the antenna to East / West.2.Fine Tune East / West: Rotates the antenna East / West for one step.3.Store nn: Store Satellites Position nn (01 60).4.Goto nn: Rotates Motor to Satellite Position nn (01 60).5.Goto 0 :Rotates the Motor to 0 as a reference point.6.Re-synchronize / Shift:(a)Rotate the motor to a position by Goto command.(b)Rotate the motor East / West to a better position.(c)Send Re-synchronize commands to the motor. The original position will be shifted to the newposition. All the other Satellite positions are also changed.Goto X Function1.See your receiver manual and select the type of installation in Goto X mode.2.Fill in the empty spaces in the receiver’s menu with the Latitude and Longitude values. Whenthe values have been correctly received, the receiver drives the Motor to the calculated position.3.Rotate the locked together antenna and motor slightly clockwise or anticlockwise until you findan image on the TV-screen connected to the receiver or the signal and quality, and then tightenthe fixing screws.LED INDICATORThe 2 LED indicators on the bottom of the motor can show the following information:FunctionPower onDrive EastDrive WestHaltStoreCallEast LimitWest LimitLimit offGoto XStatusLED1 & LED2 Blink every 2 SecondsLED1 Blinks onceLED2 Blinks onceLED1 & LED2 Blink onceLED1 Blinks TwiceLED2 Blinks TwiceLED1 Blinks 3 timesLED2 Blinks 3 timesLED1 & LED2 Blink 3 timesLED1 & LED2 Blink 4 timesStop East LimitLED1 Keeps BlinkingStop West LimitLED2 Keeps BlinkingImported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95954
HARDWARE RESET BY RECEIVER1. Execute the command: Go To Reference (Go To “0”).2. Cut off the power by disconnecting the coaxial cable.3. Reconnect the coaxial cable.4. Execute the command: Shift “0”.5. Then, its memory erased, the receiver rewrites the satellite table to initial one and corrects the “0”HARDWARE RESET BY DiSEqC MOTOR1. Cut off the power by disconnecting the coaxial cable.2. Press and hold both EAST / WEST buttons for 5 seconds.3. Reconnect the coaxial cable.4. LED1 and LED2 blink for 5 seconds.5. Then, its memory erased, the receiver rewrites the satellite table to initial one and corrects the “0”BUILT-IN SATELLITE TABLE RESET1. Press and hold both EAST / WEST buttons for 5 seconds.2. LED1 and LED2 blink for 5 seconds.3. Then, its memory erased and rewrites the built-in Satellite table to initial one.Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95955
Troubleshooting the H-H MountSymptomsCheck pointsThe manual buttons don’t work1. Connect the Motor to the receiver via coaxial cable firstand make sure the receiver power is on.The Mount doesn’t work1. Ensure all cables and power are connected well.2. Check if the receiver is DiSEqC 1.2. If not, try to use ourinterface box.3. Check whether the dish is too heavy.1. Disable the software limits and move the motor again.The Mount stops at some positions 2. Make sure the Mount or antenna are not interfered withand can’t go fartherany other item.The Mount runs intermittently1. Make sure the antenna is not too heavy or too large.2. Check if the cable quality is good enough. Try a better RG6U cable.3. Check whether the output power of the receiver is higherthan 350mA.The Mount sometimes runs fast and 1. The speed of the Mount varies with receiver output voltage(13/18Vdc)sometimes runs slowly1. Correct this problem via the “Goto 0”Function, the Mountwill go to 0 degree as a reference point.ORAll satellite positions are not correct. 2. Goto a satellite position via receiver or interface box. Waitfor about 30 seconds until the motor stops.3. Drive the antenna East or West until the reception of thissatellite is clear.4. Use “Re-calculate” or “Shift” Function to correct position.Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95956
SPECIFICATION․ H-H MountProtocolCompatible ReceiverAntenna SizeSpeedAzimuth AngleElevation AngleInput VoltageOutput VoltagePower ConsumptionSatellite PositionsCalibration FunctionManual East/West ButtonsLimit ProtectionPositioning SensorConnectorWeight ( Mount )Dimension ( Mount )DiSEqC 1.2 & Goto “X”Receiver with DiSEqC 1.2 or Interface Box120 cm Max.1.9 / sec (at 13V) ; 2.5 / sec (at 18V)80 East 80 West ( 160 )25 75 13 / 18Vdc13 / 18Vdc50 mA (Standby)200mA (Normal)350mA (Max.)60 positionsYes ( Go to 0 )Yes (Build-in on the bottom of the Mount)1.Fixed type with microswitches2.Programmable Software Limit3.Current LimitHigh Resolution Hall Effect SensorF-Type3.1 Kg (Net) / 3.5 Kg (Gross) ( 8 lbs)345 x 168 x 110 mm3 (Gross)DiSEqCTM is a trademark of EUTELSATImported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95957
ELEVATION AND DECLINATION ANGLE TABLEYour 24252627282930313233Elevation etAngleYour 6668707274767880Elevation 241403938373634323028262422201816141210Imported and distributed by Sadoun Satellite Sales, www.sadoun.com .426.426.426.326.38
Pre-Stored Satellites Table15.0 WTelstar 1270.0 WBrasilsat B4103.0 WAMC 120.0 WIntelsat 60322.0 WNSS 772.0 WNahuel 1105.0 WAMC 1572.5 WDirecTV 1107.3 WAnik F124.5 WIntelsat 90573.5 WBrasilsat B1110.0 WDirecTV 527.5 WIntelsat 90774.0 WSBS 6111.1 WAnik F230.0 WHispasat 1C76.8 WGalaxy 4R113.0 WSatMex 631.5 WIntelsat 80179.0 WAMC 5114.9 WSolidaridad 234.5 WIntelsat 90382.0 WNimiq 2116.8 WSatMex 534.5 WTelstar 1183.0 WAMC 9119.0 WAMC 1640.5 WNSS 80684.0 WBrasilsat B3121.0 WEchoStar 943.0 WIntelsat 6B85.0 WAMC 2123.0 WGalaxy 10R45.0 WIntelsat 1R87.0 WAMC 3125.0 WGalaxy 1450.0 WIntelsat 70589.0 WGalaxy 28127.0 WGalaxy 1353.0 WIntelsat 70791.0 WGalaxy 11129.0 WEchoStar 555.5 WIntelsat 80593.0 WGalaxy 26131.0 WAMC 1158.0 WIntelsat 995.0 WGalaxy 3C133.0 WGalaxy 1561.0 WAmazonas97.0 WGalaxy 25135.0 WAMC 1061.5 WEchoStar 399.0 WGalaxy 16137.0 WAMC 763.0 WEstrela do Sul 1101.0 WDirecTV139.0 WAMC 865.0 WBrasilsat B2102.8 WSpaceway 1148.0 WEchoStar 1Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-95959
ZEITORMO AOTICEENNCHO TE ANTTSBELLITHE R SATEUOYDG240
Imported and distributed by Sadoun Satellite Sales, www.sadoun.com 1-888-519-9595 2. ADJUST THE TUBE LOOSE If you incur the problem of loose tube, follow the procedure to solve it: 1.Loosen the 4 screws (#1 on the picture) a little 2.Tighten the screw (#2 on the picture) a little.
