Transcription
Course CatalogV509 June 2017
3DS Learning Solutions Course Catalog 2007-2017 Dassault Systèmes - All rights reservedNo part of this publication may be reproduced, translated, stored in retrieval system or transmitted, inany form or by any means, including electronic, mechanical, photocopying, recording or otherwise,without the express prior written permission of DASSAULT SYSTEMES. This courseware may onlybe used with explicit DASSAULT SYSTEMES agreement.
3DS Learning Solutions Course CatalogCATIACATIA Analysis V51CATIA V5 Analysis (V5A)2ELFINI Structural Analysis (EST)3FEM Solid (FMD)5FEM Surface (FMS)7Generative Assembly Structural Analysis (GAS)9Generative Dynamic Response Analysis (GDY)11Generative Part Structural Analysis Expert (GPE)12Generative Part Structural Analysis Fundamentals (GPF)14CATIA Application Architecture V515CAA for CATIA V5 – Getting Started (CAG)16CATIA Equipment and Systems Engineering V517CATIA V5 for Electrical Designers (V5VE)18Circuit Board Design (CBD)20Electrical 3D Design and Documentation (EC1)21Electrical Harness Flattening (EHF)22Electrical Librarian and Harness Installation (ELI)23Electrical Wire Routing (EWR)24Equipment and Systems Environment (ES1)25Equipment and Systems Setup and Administration (ESA)26Equipment Arrangement (EQT)27Equipment Arrangement Setup (EQS)28Experience CATELECTRE (CEL)29Generic Routing (ES2)30HVAC Design (HVA)31HVAC Diagrams (HVD)32HVAC Setup and Catalogs (HVS)33Piping and Instrumentation Diagrams (PID)34Piping Design (PIP)35Piping Setup (PIS)36Structure Detail Design (SDD)37Structure Functional and Design Setup (STS)38
3DS Learning Solutions Course CatalogStructure Functional Design (SFD)39Tubing Catalogs (2D Diagrams and 3D Design) (TUS)40Tubing Design (TUB)41Tubing Diagrams (TUD)42CATIA Infrastructure V543CATIA V5 Automation (VBA)44V5 Administration (ADM)45CATIA Machining V546Advanced Part Machining (AMG)47Lathe Machining (LMG)48Multi-Axis Surface Machining (MMG)49Multi-Pockets Machining (MPG)50Multi- Slide Lathe Machining (MLG)51Numerical Control Infrastructure (NCI)53Prismatic Machining (PMG)54Prismatic Machining Preparation Assistant (MPA)55STL Rapid Prototyping (STL)56Surface Machining (SMG)57CATIA Mechanical Design V5582D Layout for 3D Design (LO1)593D Functional Tolerancing and Annotation (FTA)60Advanced Drafting and Customization (DRA)61Aerospace Sheetmetal Design (ASL)62CATIA Composites Design V5R20 Update (UCPD20)63CATIA Detail Drafting (DDR)64CATIA Generative Drafting Fundamentals (ANSI) (GDRA)65CATIA Generative Drafting Fundamentals (ISO) (GDRI)66CATIA Generative Sheetmetal Design (SMD)67CATIA Generative Sheetmetal Design V5R19 Updates (SMD)68CATIA Generative Sheetmetal Design V5R20 Updates (USMD20)69CATIA Mechanical Design V5-6R2012 Update (UMD22)70CATIA Mechanical Design V5-6R2013 Update (UMD23)71CATIA Mechanical Design V5R19 to V5-6R2014 Update (UMD94)72CATIA Mechanical Design V5R19 Update (MD2)73CATIA Mechanical Design V5R20 Update (UMD20)74CATIA Part Design (PDG)75
3DS Learning Solutions Course CatalogCATIA Part Design Added Exercises (PDG)76CATIA Part Design Expert (PDG)77CATIA Product Design (ASM)78CATIA Product Design Added Exercises (ASM)79CATIA Product Design Expert (ASM)80CATIA Sketcher (SKE)81CATIA Surface Design (GS1)82CATIA Surface Design Added Exercises (GS1)83CATIA Tools For Proficient Users (PRO)84CATIA V5-6R2014 to V5-6R2016 Update for Mechanical Designers (UMD46)85CATIA V5-6R2014 Update for Designers (UMSD24)86CATIA V5-6R2015 Update for Mechanical Designers (UMD25)87CATIA V5-6R2016 Update for Mechanical Designers (UMD26)88CATIA V5-6R2017 Update for Mechanical Designers (UMD27)89CATIA V5 Foundations for Aerospace Assembly Designers (V5AeA)90CATIA V5 Foundations for Aerospace Part Designers (V5AeD)91CATIA V5 Foundations for Aerospace Part Reviewers (V5AeR)92CATIA V5 Foundations for Body Designers (V5VB)93CATIA V5 Foundations for Chassis Designers (V5VC)94CATIA V5 Foundations for Powertrain Designers (V5VP)95CATIA V5 Fundamentals (V5F)96CATIA V5 Mechanical Design Expert (V5E)97CATIA V5-V6 Design Synchronization Essentials (DCE5)98Composites Grid Approach (CPG)100Composites Part Engineering (CPE)101Composites Part Manufacturing (CPM)102Core and Cavity Design (CCV)104Functional Molded Parts (FMP)105Getting Started with CATIA V5 (COM)106Healing Assistant (HA1)107Mold Tooling Design (MTD)108Part Design Features Recognition (FR1)109SEE Project : Assembly Design (SEEASM)110SEE Project : Drafting Design (SEEGDR)111SEE Project : Part Design (SEEPDG)112Tooling Design (TG1)113
3DS Learning Solutions Course CatalogWeld Design (WD1)114CATIA PLM Express V5115CATIA PLM Express Fundamentals (CTP)116CATIA PLM Express Fundamentals - Basic Surface (CTPB)117CATIA PLM Express Fundamentals - Surfaces (CTPS)118CATIA Product Synthesis V5119CATIA Knowledge Fundamentals (KWF)120Human Modeling (HMN)121Knowledge Advisor (KWA)122Knowledge Expert (KWE)123Product Engineering Optimizer (PEO)124Product Knowledge Template (PKT)125CATIA Shape Design and Styling V5126Automotive Body in White Fastening (ABF)127CATIA Digitized Shape Editor (DSE)128CATIA For Design Foundations (CDF)129CATIA Generative Shape Design V5-6R2012 Update (UHD22)130CATIA Generative Shape Design V5-6R2013 Update (UHD23)131CATIA Generative Shape Design V5R19 to V5-6R2014 Update (UHD94)132CATIA Generative Shape Design V5R20 Update (UHD20)133CATIA Generative Shape Design V5R21 Update (UHD21)134CATIA ICEM Shape Design Expert (IEX5)135CATIA ICEM Shape Design Fundamentals (ICM)136CATIA Imagine and Shape (IMA)137CATIA Surface Design Expert (GSD)138CATIA Surface Design Expert Added Exercises (GSD)139CATIA V5-6R2014 to V5-6R2016 Update for Shape Designers (UHD46)140CATIA V5-6R2015 Update for Shape Designers (UHD25)141CATIA V5-6R2016 Update for Shape Designers (UHD26)142CATIA V5-6R2017 Update for Shape Designers (UHD27)143CATIA V5 for Surfaces (V5S)144Developed Shapes (DL1)145FreeStyle Shaper, Optimizer and Profiler (FSS)146Freestyle Sketch Tracer (FSK)147Generative Shape Design Optimizer (GSO)148Generative Shape Design V5R19 Update (HD2)149
3DS Learning Solutions Course CatalogIntroduction to the mathematical concepts of CATIA V5 (MTH)150Methodology for Cloud to Surface (CTS)151Photo Studio (PHS)152Photo Studio Optimizer (PSO)153Quick Surface Reconstruction (QSR)154Realistic Shape Optimizer (RSO)155Real Time Rendering (RTR)156Shape Sculptor (DSS)157Solutions V5158Photo Rendering (PRS)159CompanionCompanion Studio160Companion Studio (WTR)161Companion Studio - Advanced (WTR)163DELMIADELMIA Assembly V5164Assembly Process Planner (APN)165Assembly Process Planner - Auto (APA)166DPM Assembly (ASY)167DPM Hub Assembly (HAS)168DELMIA D5 QUEST V5169Advanced QUEST (AQT)170QUEST (QST)171DELMIA Human V5172Human Option (HSO)173Virtual Ergonomics Solutions (HUM)174DELMIA Lofting V5175DPM Structure Lofting (DST)176Structure Manufacturing Preparation (SMP)177DELMIA Machining V5178DPM Machining Process Planner (MPP)179NC Machine Tool Builder (MBG)180NC Machine Tool Simulation (MSG)181
3DS Learning Solutions Course CatalogDELMIA Manufacturing Hub V5182Basic Process Engineer (DPE)183DELMIA PLM Express V5184Automation (AUTO)185PLMX Arc Welding (ARB)186PLMX Human (XHM)187PLMX Spot Robotics (SRB)188PLMX Workcell Builder (RWB)189DELMIA Robotics V5190Body in White Fastener Planning (BIW)191DELMIA Device Building - Advanced Kinematics (DBG)193DELMIA Robotics for Aerospace (WLA)194V5 Robotics (ROB)196VBA for DELMIA (VBD)197ENOVIADigital Mock-Up V5198Digital Mock-Up Basics (DMB)199Digital Mock-Up Navigator (DMN)200Digital Mock-Up Optimizer (DMO)201Digital Mock-Up Space Analysis (SPA)202DMU Engineering Analysis Review (ANR)203DMU Fitting Simulator (FIT)204DMU Kinematics Simulator (KIN)205ENOVIA PLM Express V5206ENOVIA SmarTeam - CATIA PLM Express Fundamentals (CTPE)207ENOVIA SmarTeam V5208ENOVIA SmarTeam Administration for Foundation, Editor and Web Editor (STA)209ENOVIA SmarTeam - CATIA Integration (TPU)210ENOVIA SmarTeam - CATIA Supply Chain Engineering Exchange (SEE)211ENOVIA SmarTeam - Editor (SED)212ENOVIA SmarTeam Fundamentals (SFF)213ENOVIA SmarTeam Installation for Foundation, Editor and Web Editor (STI)214ENOVIA SmarTeam - Web Editor (WED)215ENOVIA V5 VPLM216ENOVIA V5 VPM for Engineering Collaboration (LEH)217
3DS Learning Solutions Course CatalogENOVIA V5 VPM for Lifecycle Collaboration (LCN)218ENOVIA V5 VPM for Supply Chain Collaboration (WPE)220ENOVIA V5 VPM Fundamentals (LUF)221SIMULIASIMULIA V5 Abaqus222Introduction to Abaqus for CATIA V5 (AFC)223SIMULIA V5 Analysis224Introduction to Nonlinear Structural Analysis And Thermal Analysis (ANL)225
3DS Learning Solutions Course CatalogCATIACATIA Analysis V51 / 226
3DS Learning Solutions Course CatalogCATIA V5 Analysis (V5A)Course CodeCAT-en-V5A-F-V5R26AvailableReleasesV5-6R2012 , V5-6R2013 , V5-6R2014 , V5-6R2015 ,V5-6R2016 , V5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical Designers and Structural AnalystsDescriptionThis course will introduce the concepts and benefitsof Finite Element Analysis and the general analysisprocess. It will teach you how to prepare a modelfor analysis, create 1D, 2D and 3D FE models, andcompute a simple static analysis for a single part or anassembly.ObjectivesUpon completion of this course you will be able to:- Create a Finite Element Analysis model- Prepare a solid or a surface model for analysis- Create 1D, 2D and 3D meshes for beam, surface,and solid models- Assign properties, loads and constraints, and defineassembly connections- Compute an analysis for a part or an assembly- Generate and display analysis resultsPrerequisitesStudents attending this course should have followedthe CATIA V5 Fundamentals course.Available OnlineYes2 / 226
3DS Learning Solutions Course CatalogELFINI Structural Analysis (EST)Course CodeCAT-en-EST-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course will teach you how to use the advancedfunctionalities provided by the ELFINI Solver. It will alsoguide you on how to use these functionalities in theoverall FEA process. Additionally, you will learn aboutnew analysis types such as Buckling Case, MultiLoadsCase, Transfer of Loads and Solution, etc. You willalso learn how to use advanced capabilities for postprocessing of results.ObjectivesUpon completion of this course you will be able to:- Use the advanced pre-processing capabilities (suchas loads and boundary conditions) to create morerealistic FE models- Visualize the images of objects used for preprocessing (which is not possible in GPS)- Use advanced case features (such as Buckling,MultiLoads, Envelope) in addition to the standardStatic and Frequency cases- Create your own result image templates, customizethe post-processing result images, group selectiveentitites in the result images, and create advancedreportsPrerequisitesStudents attending this course should be familiar withGenerative Part Structural Analysis Fundamentals,3 / 226
3DS Learning Solutions Course CatalogELFINI Structural Analysis (EST)Generative Assembly Structural Analysis, FEM SurfaceMeshingAvailable OnlineYes4 / 226
3DS Learning Solutions Course CatalogFEM Solid (FMD)Course CodeCAT-en-FMD-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration4 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course introduces you to the variousfunctionalities available with the FEM Solid (FMD)license in CATIA. You will learn how to a create 3Dmesh from existing 2D mesh parts with the help offunctionalities such as Tetrahedron Filler, Sweep3D,mesh part transformations, and mesh part extrusion.You will also learn how to directly generate a 3D meshusing OCTREE Tetrahedron Mesher. You will learnhow to analyze the generated 3D mesh using theavailable mesh quality criteria, and how to import/export the meshes into/from CATIA.ObjectivesUpon completion of this course you will be able to:- Use different solid meshers such as TetrahedronFiller, OCTREE Tetrahedron Mesher, Sweep3DMesher- Create a solid mesh using mesh parttransformations like Translation, Rotation, andSymmetry on 3D mesh parts- Analyze the solid meshes using the available meshquality criteria- Import/Export the meshes into/from CATIAPrerequisitesGenerative Part Structural AnalysisFundamentals,Generative Part Structural Analysis5 / 226
3DS Learning Solutions Course CatalogFEM Solid (FMD)Expert, Generative Assembly Structural Analysis, FEMSurface MeshingAvailable OnlineYes6 / 226
3DS Learning Solutions Course CatalogFEM Surface (FMS)Course CodeCAT-en-FMS-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration16 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course will teach you how to create and editmeshes using Beam Mesher, OCTREE TriangularMesher, Surface Mesher and Advanced SurfaceMesher. You will learn how to create meshes fromexisting meshes using mesh transformations. You willalso learn how to create different types of WeldingMeshes. This course will teach you how to make useof knowledgeware parameters while creating SurfaceMeshes. Additionally, you will learn how to analyze themesh quality using the available mesh quality checks.ObjectivesUpon completion of this course you will be able to:- Use the various Meshers such as Surface Mesher,Advanced Surface Mesher, Beam Mesher, andOCTREE Triangle Mesher- Create a new mesh using existing mesh withthe help of mesh transformation tools and meshoperators- Edit the mesh using the mesh edition tools availablewithin the above mentioned meshers- Analyze the mesh quality using mesh qualitychecks and tools like Free Edges, DuplicateElements, Duplicate Nodes, Mesh InterferenceChecks, etc.7 / 226
3DS Learning Solutions Course CatalogFEM Surface (FMS)PrerequisitesGenerative Part Structural Analysis Fundamentals,Generative Assembly Structural AnalysisAvailable OnlineYes8 / 226
3DS Learning Solutions Course CatalogGenerative Assembly Structural Analysis (GAS)Course CodeCAT-en-GAS-F-V5R27AvailableReleasesV5-6R2012 , V5-6R2013 , V5-6R2014 , V5-6R2015 ,V5-6R2016 , V5-6R2017 , V5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course will teach you how to conduct a FiniteElement Analysis using an existing assembly. You willlearn how to create connections between assemblycomponents and how to assign appropriate connectionproperties. You will also learn how to create ananalysis assembly from the existing meshed parts.ObjectivesUpon completion of this course you will be able to:- Interpret the various types of hypotheses thatare used for creating an assembly analysis anddifferentiate between them- Define analysis connections between assemblycomponents- Use existing assembly constraints to automaticallycreate analysis connections- Assign a connection property to the appropriateanalysis connection- Compute a static analysis for an assembly- Create and manage an analysis assembly modelusing existing meshed partsPrerequisitesStudents attending this course should have completedthe CATIA V5 Fundamentals and Generative PartStructural Analysis Fundamentals courses9 / 226
3DS Learning Solutions Course CatalogGenerative Assembly Structural Analysis (GAS)Available OnlineYes10 / 226
3DS Learning Solutions Course CatalogGenerative Dynamic Response Analysis (GDY)Course CodeCAT-en-GDY-F-V5R27AvailableReleasesV5-6R2012 , V5-6R2013 , V5-6R2014 , V5-6R2015 ,V5-6R2016 , V5-6R2017 , V5R19 , V5R20 , V5R21Duration4 hoursCourse MaterialEnglishLevelFundamentalAudienceStructural AnalystsDescriptionThis course will teach you how to conduct a harmonicor transient analysis on a single part using finiteelements. You will learn how to generate and visualize2D graphical results and how to export the resultingdata in Text or Excel format.ObjectivesUpon completion of this course you will be able to:- Interpret harmonic and transient analyses anddifferentiate between them- Define the load and restraint excitations- Define the correct prerequisites for an excitationcase- Visualize and animate the 3D images of theanalysis results- Generate the translation, velocity, and accelerationgraphs- Export the results data in Text or Excel formatPrerequisitesStudents attending this course should have completedthe CATIA V5 Fundamentals and Generative PartStructural Analysis Fundamentals coursesAvailable OnlineYes11 / 226
3DS Learning Solutions Course CatalogGenerative Part Structural Analysis Expert (GPE)Course CodeCAT-en-GPE-F-V5R27AvailableReleasesV5-6R2012 , V5-6R2013 , V5-6R2014 , V5-6R2015 ,V5-6R2016 , V5-6R2017 , V5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course will teach you how to use advanced FiniteElement Analysis pre-processing techniques and postprocessing tools, including the concept of definingvirtual parts to avoid excessive geometric modeling.You will learn how to perform frequency analysis ona single part, and how to use adaptive meshing toachieve pre-defined accuracy.ObjectivesUpon completion of this course you will be able to:- Define and customize the material properties of theparts to be analyzed- Apply pressure, acceleration, and force densityloads- Define virtual parts to simplify the analysis- Apply pivot, ball-joint, and user-defined restraints- Compute frequency analysis for a single part- Create planar sections to visualize the internalresult values- Compute and refine a mesh using adaptivemeshing in order to achieve the pre-definedaccuracyPrerequisitesStudents attending this course should have completedthe CATIA V5 Fundamentals and Generative PartStructural Analysis Fundamentals courses12 / 226
3DS Learning Solutions Course CatalogGenerative Part Structural Analysis Expert (GPE)Available OnlineYes13 / 226
3DS Learning Solutions Course CatalogGenerative Part Structural Analysis Fundamentals(GPF)Course CodeCAT-en-GPF-F-V5R27AvailableReleasesV5-6R2012 , V5-6R2013 , V5-6R2014 , V5-6R2015 ,V5-6R2016 , V5-6R2017 , V5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceMechanical DesignersDescriptionThis course will teach you the basic concepts of FiniteElement Analysis and the general analysis process.You will learn how to conduct a simple static analysison a single part using finite elements, and how toproduce the final report of the analysis results.ObjectivesUpon completion of this course you will be able to:- Predict why, when, and how to use Finite ElementAnalysis- Use different element types and shapes to mesh apart- Apply clamp, slider, and iso-static restraints- Apply force, moment, and displacement loads- Compute static analysis for a single part- Visualize the images of the analysis results andproduce the analysis reports- Refine existing meshes to produce more accurateresultsPrerequisitesStudents attending this course should be familiar withthe fundamentals of CATIA V5Available OnlineYes14 / 226
3DS Learning Solutions Course CatalogCATIACATIA Application Architecture V515 / 226
3DS Learning Solutions Course CatalogCAA for CATIA V5 – Getting Started (CAG)Course CodeCAT-en-CAG-A-V5R23Available ReleaseV5-6R2013Duration45 hoursCourse MaterialEnglishLevelAdvancedAudienceCAD / CAM DevelopersDescriptionThis course will teach you how to use CAA to createand scan CATIA models. You will also learn howto create your own commands, knowledgewareparameters, relations and to manage the softwarequality.ObjectivesUpon completion of this course you will be able to:- Use CAA Development Environment andDocumentation- Handle V5 Objects- Create and Scan Models- Manage the 3D Model Screen Layout- Manage User Interface and Interactions- Use CAA Knowledgeware through code- Manage Software Quality and DeliveryPrerequisites-Available OnlineCATIA V5 Interactive (Assembly Design, PartDesign, Generative Shape Design, KnowledgeAdvisor)C ProgrammingYes16 / 226
3DS Learning Solutions Course CatalogCATIACATIA Equipment and SystemsEngineering V517 / 226
3DS Learning Solutions Course CatalogCATIA V5 for Electrical Designers (V5VE)Course CodeCAT-en-V5VE-F-V5R26AvailableReleasesV5-6R2013 , V5-6R2014 , V5-6R2015 , V5-6R2016 ,V5R19 , V5R20 , V5R21Duration48 hoursCourse MaterialEnglishLevelFundamentalAudienceAutomotive Electrical Harness Designers and newCATIA Electrical Designers.DescriptionThis course will introduce you to the fundamentalconcepts of CATIA V5. You will learn how to designparts and assemblies and create simple drawings.Once you are familiar with the fundamentals, you willbe introduced to the Electrical Library products. Youwill learn how to create the Electrical Harness for anautomotive assembly. You will also learn how to mapthe functional specifications of the Harness system tothe digital mock-up created in CATIA V5 and create theharness documentation.ObjectivesUpon completion of this course you will be able to:- Understand the CATIA V5 interface- Design an automotive wire harness- Route the signals and create the wires- Flatten and synchronize the harness- Design and manage parts in the context of anassembly- Generate harness documentation- Produce simple drawingsPrerequisitesStudents attending this course should be familiarwith Mechanical Design and the Windows OperatingSystem.18 / 226
3DS Learning Solutions Course CatalogCATIA V5 for Electrical Designers (V5VE)Available OnlineYes19 / 226
3DS Learning Solutions Course CatalogCircuit Board Design (CBD)Course CodeCAT-en-CBD-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration4 hoursCourse MaterialEnglishLevelFundamentalAudienceElectrical DesignersDescriptionThis course will teach you how to use the CATIA CircuitBoard Design workbench. You will learn how to designcircuit board geometry in the context of mechanicalassembly, and create spatial and technologicalconstraint areas. You will also learn how to exchangedata with ECAD systems through IDF Files (Import /Export) and create catalogs of electronic parts.ObjectivesUnderstand and use the CATIA Circuit Board Designworkbench- Create Printed Circuit Boards in the context of anassembly- Export or import PCBs with an ECAD tool using theIDF interfacePrerequisitesStudents attending this course should be familiar withthe fundamentals of Mechanical Design with CATIA V5.Available OnlineYes20 / 226
3DS Learning Solutions Course CatalogElectrical 3D Design and Documentation (EC1)Course CodeCAT-en-EC1-F-V5R26AvailableReleasesV5-6R2013 , V5-6R2014 , V5-6R2015 , V5-6R2016 ,V5R19 , V5R20 , V5R21Duration16 hoursCourse MaterialEnglishLevelFundamentalAudienceElectrical Harness DesignersDescriptionThis course will teach you how to use the Electrical 3DDesign Part and Assembly workbenches with a focuson the Consumer Goods industry. You will learn how tocreate electrical assemblies, route multi-branchables,route wires, and create drawings of the electricalharness assemblies.ObjectivesUpon completion of this course you will be able to:- Create harnesses suitable for consumer goods- Design wire harnesses with appliances- Route signals and create wires- Flatten and synchronize an electrical or ageometrical harness- Generate the harness documentation- Produce simple drawingsPrerequisitesStudents attending this course should be familiar withthe fundamentals of CATIA V5. They should know howto use the Part Design, the Assembly Design and theDrafting workbenches.Available OnlineYes21 / 226
3DS Learning Solutions Course CatalogElectrical Harness Flattening (EHF)Course CodeCAT-en-EHF-F-V5R26AvailableReleasesV5-6R2013 , V5-6R2014 , V5-6R2015 , V5-6R2016 ,V5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceElectrical DesignersDescriptionThis course will teach you how to use the ElectricalHarness Flattening workbench to extract, flatten andsynchronize an electrical / geometrical harness. Youwill learn how to manipulate the flattened harness andhow to define and generate a harness flattening report.You will also learn how to use text templates to createan annotated and dimensioned 2D drawing of a 3Dharness.ObjectivesUpon completion of this course you will be able to:- Extract, flatten and synch electrical and geometricalharnesses- Modify the bundle segments of a harness to fit yourdrawing- Define and generate reports- Create 2D drawings of a 3D harness- Create a Text Templates CatalogPrerequisitesStudents attending this course should be familiarwith the CATIA V5 Catalog Editor, Electrical HarnessInstallation and Assembly, and Wire Routing.Available OnlineYes22 / 226
3DS Learning Solutions Course CatalogElectrical Librarian and Harness Installation (ELI)Course CodeCAT-en-ELI-F-V5R26AvailableReleasesV5-6R2013 , V5-6R2014 , V5-6R2015 , V5-6R2016 ,V5R19 , V5R20 , V5R21Duration16 hoursCourse MaterialEnglishLevelFundamentalAudienceElectrical Harness DesignersDescriptionThis course will teach you how to create an ElectricalComponents Catalog. You will learn how to designharnesses, create bundle segments and connect themto electrical components. You will also learn how tomanage the branch points, protections and links, andhow to perform knowledge checks.ObjectivesUpon completion of this course you will be able to:- Build and manage an Electrical ComponentsCatalog- Design a harness that is integrated within the DigitalMock-Up- Connect bundle segments to electrical componentsPrerequisitesStudents attending this course should be familiar withthe fundamentals of CATIA V5. They should knowhow to use the Part Design and the Catalog Editorworkbenches.Available OnlineYes23 / 226
3DS Learning Solutions Course CatalogElectrical Wire Routing (EWR)Course CodeCAT-en-EWR-F-V5R26AvailableReleasesV5-6R2013 , V5-6R2014 , V5-6R2015 , V5-6R2016 ,V5R19 , V5R20 , V5R21Duration4 hoursCourse MaterialEnglishLevelFundamentalAudienceElectrical DesignersDescriptionThis course will teach you how to use the ElectricalWire Routing workbench to route signals and createwires using a harness and a functional definition. Youwill also learn how to integrate external tools withCATIA's electrical products.ObjectivesUpon completion of this course you will be able to:- Route signals- Create wires- Integrate external tools with CATIA's electricalproductsPrerequisitesStudents attending this course should be familiar withthe fundamentals of CATIA V5. They should knowhow to use the Electrical Librarian and the ElectricalHarness Installation workbenches.Available OnlineYes24 / 226
3DS Learning Solutions Course CatalogEquipment and Systems Environment (ES1)Course CodeCAT-en-ES1-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration1 hoursCourse MaterialEnglishLevelFundamentalAudienceAll Students for Equipment and Systems trainingDescriptionThis course will teach you how to organize variousproducts under CATIA Equipment and Systemsdomain. You will learn about the structure of theEquipment and Systems courses. You will also learnabout the difference between setup-data and designdata.ObjectivesPresent an overview of CATIA V5 Equipment andSystems Portfolio- Identify the Industrial General Process- Manage Project Resources and Concurrentengineering approach- Organize the DataPrerequisitesNoneAvailable OnlineYes25 / 226
3DS Learning Solutions Course CatalogEquipment and Systems Setup and Administration(ESA)Course CodeCAT-en-ESA-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration8 hoursCourse MaterialEnglishLevelFundamentalAudienceEquipment and System Designers, Equipment &System AdministratorsDescriptionThis course will teach you how to create and configurea new project in the Equipment and Systems discipline.You will learn how to perform the administrative tasksduring the new project creation.ObjectivesUpon completion of this course you will be able to:- Create the structure and organize the data- Create the site and project directories- Set up the project environment- Configure and manage the project resources- Set up the project- Define the drafting standards, Generative ViewStyles and Backing SheetsPrerequisitesStudents attending this course should know the basicsof CATIA V5.Available OnlineYes26 / 226
3DS Learning Solutions Course CatalogEquipment Arrangement (EQT)Course CodeCAT-en-EQT-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration4 hoursCourse MaterialEnglishLevelFundamentalAudienceEngineers, Equipment and Systems DesignersDescriptionThis course will teach you how to use the EquipmentArrangement workbench to administrate catalogs forequipments in manufacturing plants, process andpower plants, and ships.ObjectivesPlace equipments and manage their positions in space- Generate reports and drawings.PrerequisitesStudents attending this course should be familiar withthe basics of CATIA V5.Available OnlineYes27 / 226
3DS Learning Solutions Course CatalogEquipment Arrangement Setup (EQS)Course CodeCAT-en-EQS-F-V5R21AvailableReleasesV5R19 , V5R20 , V5R21Duration24 hoursCourse MaterialEnglishLevelFundamentalAudienceEquipment AdministratorDescriptionThis course will teach you how to use the EquipmentArrangement workbench to administrate catalogs forequipments in manufacturing plants, process andpower plants, and ships .ObjectivesCreate a feature dictionary- Manage design rules- Create a 2D Diagram Catalog- Create a 3D Library CatalogPrerequisitesStudents attending this course should be familiar withEquipment and Systems Setup and Administration,Equipment Arrangement.Available OnlineYes28 / 226
3DS Learning Solutions Course CatalogExperience CATELECTRE (CEL)Course CodeCAT-en-CEL-F-V5R20Available ReleaseV5R20Duration2 hoursCourse nThis course will teach you how to work withCATELECTRE in CATIA for designing an electricalharness. You will l
CATIA V5-6R2014 to V5-6R2016 Update for Shape Designers (UHD46) 140 CATIA V5-6R2015 Update for Shape Designers (UHD25) 141 CATIA V5-6R2016 Update for Shape Designers (UHD26) 142 CATIA V5-6R2017 Update for Shape Designers (UHD27) 143 CATIA V5 for Surfaces (V5S) 144 Developed Shapes (DL1) 145
