Transcription
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14Assignment: At the February 2021 virtual meeting the Committee members presentvoted to submit the following for letter ballot:rovedAdd full titles of standards to Chapter 15 GlossaryRationale: Many standards within Chapter 15 show only the standard number (forexample, see various ASTM standards). Existing References are called from within thetext. Adding Reference calls was not desirable, and adding material to Referenceswithout its being cited would be inconsistent. This ballot proposes to add the entirestandard title under its governing body to the Glossary of Chapter 15.Submitted by:April 30, 2021ppDue Date:tAEdit and add entries to Glossary as shown (additions shown as underlined bold red,deletions shown as bold red strikethrough, comments in brackets [ ] not part ofpublished language):AARYeAssociation of American Railroads, 425 3rd Street SW, Suite 1000, Washington, DC 20024. www.aar.org.Term cited in Parts 6, 7, 8 and 9. Standards cited include:AAR Manual of Standards and Recommended PracticesAASHTOtNotAmerican Association of State Highway and Transportation Officials, 555 12th St NW, Suite 1000,Washington, D.C. 20004. www.transportation.org. Term cited in Parts 1, 3, 5, 8 and 9. Standards citedinclude:AASHTO LRFD Bridge Design SpecificationsAASHTO Standard Specifications for Highway BridgesAASHTO/AWS D1.5M/D1.5 Bridge Welding CodeAASHTO/NSBA Steel Bridge Collaboration (SBC)rafStandards cited include:S8.1 Guide Specification for Application of Coating Systems with Zinc-Rich Primers to Steel BridgesS8.2 Specification for Application of Thermal Spray Coating Systems to Steel BridgesDAGMAAmerican Gear Manufacturers Association. www.agma.org. AGMA standards cited include:AGMA 2000 Gear Classification and Inspection Handbook – Tolerances and Measuring Methods forUnassembled Spur and Helical Gears (Including Metric Equivalents)AGMA 6010 Standard for Spur, Helical, Herringbone and Bevel Enclosed Drives
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14AISCrovedAmerican Institute of Steel Construction, 130 East Randolph, Suite 2000, Chicago, IL 60601. www.aisc.org.Term cited in Parts 3 and 9. Standards cited include:AISC 303 Code of Standard Practice for Steel Buildings and BridgesAISC Manual of Steel ConstructionAISC 207 Standard for Certification ProgramsAISC 360 Specification for Structural Steel BuildingsASMEppAmerican Society of Mechanical Engineers. www.asme.org. ASME standards cited include:ASME B1.1 Unified Inch Screw Threads (UN, UNR, and UNJ Thread Forms)ASME B4.1 Preferred Limits and Fits for Cylindrical PartsASME B17.1 Keys and KeyseatsASME B18.1.2 Large RivetsASME B18.2 Square and Hexagon Bolts and NutsASME B18.3 Socket Cap, Shoulder, Set Screws, and Hex Keys (Inch Series)ASME B46.1 Surface Texture (Surface Roughness, Waviness, and Lay)ASTMDraftNotYetAASTM International. www.astm.org. ASTM International standards cited include:ASTM A6/A6M Standard Specification for General Requirements for Rolled Structural Steel Bars,Plates, Shapes, and Sheet PilingASTM A27/A27M Standard Specification for Steel Castings, Carbon, for General ApplicationASTM A36/A36M Standard Specification for Carbon Structural SteelASTM A47/A47M Standard Specification for Ferritic Malleable Iron CastingsASTM A48/A48M Standard Specification for Gray Iron CastingsASTM A53/A53M Standard Specification for Pipe, Steel, Black and Hot-Dipped, Zinc-Coated,Welded and SeamlessASTM A106/A106M Standard Specification for Seamless Carbon Steel Pipe for High-TemperatureServiceASTM A108 Standard Specification for Steel Bar, Carbon and Alloy, Cold-FinishedASTM A123 Standard Specification for Zinc (Hot-Dipped Galvanized) Coatings on Iron and SteelProductsASTM A148/A148M Standard Specification for Steel Castings, High Strength, for StructuralPurposesASTM A153/A153M Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel HardwareASTM A193/A193M Standard Specification for Alloy-Steel and Stainless Steel Bolting for HighTemperature or High Pressure Service and Other Special Purpose ApplicationsASTM A240/A240M Standard Specification for Chromium and Chromium-Nickel Stainless SteelPlate, Sheet, and Strip for Pressure Vessels and for General ApplicationsASTM A269/A269M Standard Specification for Seamless and Welded Austenitic Stainless SteelTubing for General ServiceASTM A276/A276M Standard Specification for Stainless Steel Bars and ShapesASTM A307 Standard Specification for Carbon Steel Bolts, Studs, and Threaded Rod 60 000 PSITensile StrengthASTM A312/A312M Standard Specification for Seamless, Welded, and Heavily Cold WorkedAustenitic Stainless Steel PipesASTM A370 Standard Test Methods and Definitions for Mechanical Testing of Steel ProductsASTM A423/A423M Standard Specification for Seamless and Electric-Welded Low-Alloy SteelTubesASTM A449 Standard Specification for Hex Cap Screws, Bolts and Studs, Steel, Heat Treated,120/105/90 ksi Minimum Tensile Strength, General UseASTM A502 Standard Specification for Rivets, Steel, StructuralASTM A504/A504M Standard Specification for Wrought Carbon Steel Wheels
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14DraftNotYetApprovedASTM A519/A519M Standard Specification for Seamless Carbon and Alloy Steel Mechanical TubingASTM A536 Standard Specification for Ductile Iron CastingsASTM A563 Standard Specification for Carbon and Alloy Steel NutsASTM A572/A572M Standard Specification for High-Strength Low-Alloy Columbium-VanadiumStructural SteelASTM A573/A573M Standard Specification for Structural Carbon Steel PlatesASTM A588/A588M Standard Specification for High-Strength Low-Alloy Structural Steel, up to 50ksi [345 MPa] Minimum Yield Point, with Atmospheric Corrosion ResistanceASTM A615/A615M Standard Specification for Deformed and Plain Carbon-Steel Bars for ConcreteReinforcementASTM A668/A668M Standard Specification for Steel Forgings, Carbon and Alloy, for GeneralIndustrial UseASTM A673/A673M Standard Specification for Sampling Procedure for Impact Testing ofStructural SteelASTM A675/A675M Standard Specification for Steel Bars, Carbon, Hot-Wrought, Special Quality,Mechanical PropertiesASTM A706/A706M Standard Specification for Deformed and Plain Low-Alloy Steel Bars forConcrete ReinforcementASTM A709/A709M Standard Specification for Structural Steel for BridgesASTM A743/A743M Standard Specification for Castings, Iron-Chromium, Iron-Chromium-Nickel,Corrosion Resistant, for General ApplicationASTM A767 Standard Specification for Zinc-Coated (Galvanized) Steel Bars for ConcreteReinforcementASTM A780 Practice for Repair of Damaged and Uncoated Areas of Hot-Dip Galvanized CoatingsASTM A789/A789M Standard Specification for Seamless and Welded Ferritic/Austenitic StainlessSteel Tubing for General ServiceASTM A931 Standard Test Method for Tension Testing of Wire Ropes and StrandASTM A941 Standard Terminology Relating to Steel, Stainless Steel, Related Alloys, and FerroalloysASTM A955/A955M Standard Specification for Deformed and Plain Stainless Steel Bars forConcrete ReinforcementASTM A992/A992M Standard Specification for Structural Steel ShapesASTM A996/A996M Standard Specification for Rail-Steel and Axle-Steel Deformed Bars forConcrete ReinforcementASTM A1007 Standard Specification for Carbon Steel Wire for Wire RopeASTM A1008/A1008M Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural,High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, RequiredHardness, Solution Hardened, and Bake HardenableASTM A1011/A1011M Standard Specification for Steel, Sheet and Strip, Hot-Rolled, Carbon,Structural, High-Strength Low-Alloy, High-Strength Low-Alloy with Improved Formability, andUltra-High StrengthASTM A1023/A1023M Standard Specification for Carbon Steel Wire Ropes for General PurposesASTM A1035/A1035M Standard Specification for Deformed and Plain, Low-Carbon, Chromium,Steel Bars for Concrete ReinforcementASTM A1094 Standard Specification for Continuous Hot-Dip Galvanized Steel Bars for ConcreteReinforcementASTM B6 Standard Specification for ZincASTM B22/B22M Standard Specification for Bronze Castings for Bridges and TurntablesASTM B23 Standard Specification for White Metal Bearing Alloys (Known Commercially as“Babbitt Metal”)ASTM B29 Standard Specification for Refined LeadASTM B100 Standard Specification for Wrought Copper-Alloy Bearing and Expansion Plates andSheets for Bridge and Other Structural UseASTM B695, Standard Specification for Coatings of Zinc Mechanically Deposited on Iron and SteelASTM C270 Standard Specification for Mortar for Unit MasonryASTM D395 Standard Test Methods for Rubber Property—Compression Set
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14DraftNotYetApprovedASTM D412 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers—TensionASTM D543 Standard Practices for Evaluating the Resistance of Plastics to Chemical ReagentsASTM D575 Standard Test Methods for Rubber Properties in CompressionASTM D610 Standard Practice for Evaluating Degree of Rusting on Painted Steel SurfacesASTM D624 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber andThermoplastic ElastomersASTM D903 Standard Test Method for Peel or Stripping Strength of Adhesive BondsASTM D1149 Standard Test Methods for Rubber Deterioration—Cracking in an Ozone ControlledEnvironmentASTM D1229 Standard Test Method for Rubber Property—Compression Set at Low TemperaturesASTM D1415 Standard Test Method for Rubber Property—International HardnessASTM D1777 Standard Test Method for Thickness of Textile MaterialsASTM D2137 Standard Test Methods for Rubber Property—Brittleness Point of Flexible Polymersand Coated FabricsASTM D2240 Standard Test Method for Rubber Property—Durometer HardnessASTM D2256 / D2256M Standard Test Method for Tensile Properties of Yarns by the Single-StrandMethodASTM D3294 Standard Specification for Polytetrafluoroethylene (PTFE) Resin Molded Sheet andMolded Basic ShapesASTM D3359 Standard Test Methods for Rating Adhesion by Tape TestASTM D4014 Standard Specification for Plain and Steel-Laminated Elastomeric Bearings forBridgesASTM D4060 Standard Test Method for Abrasion Resistance of Organic Coatings by the TaberAbraserASTM D4138 Standard Practices for Measurement of Dry Film Thickness of Protective CoatingSystems by Destructive, Cross-Sectioning MeansASTM D4214 Standard Test Methods for Evaluating the Degree of Chalking of Exterior Paint FilmsASTM D4285 Standard Test Method for Indicating Oil or Water in Compressed AirASTM D4414 Standard Practice for Measurement of Wet Film Thickness by Notch GagesASTM D4417 Standard Test Methods for Field Measurement of Surface Profile of Blast CleanedSteelASTM D4541 Standard Test Method for Pull-Off Strength of Coatings Using Portable AdhesionTestersASTM D4752 Standard Practice for Measuring MEK Resistance of Ethyl Silicate (Inorganic) ZincRich Primers by Solvent RubASTM D4894 Standard Specification for Polytetrafluoroethylene (PTFE) Granular Molding andRam Extrusion MaterialsASTM D4940 Standard Test Method for Conductimetric Analysis of Water Soluble IonicContamination of Blast Cleaning AbrasivesASTM D5064 Standard Practice for Conducting a Patch Test to Assess Coating CompatibilityASTM D5065 Standard Guide for Assessing the Condition of Aged Coatings on Steel SurfacesASTM D5894 Standard Practice for Cyclic Salt Fog/UV Exposure of Painted Metal, (AlternatingExposures in a Fog/Dry Cabinet and a UV/Condensation Cabinet)ASTM D6386 Standard Practice for Preparation of Zinc (Hot-Dip Galvanized) Coated Iron and SteelProduct and Hardware Surfaces for PaintingASTM D6677 Standard Test Method for Evaluating Adhesion by KnifeASTM D7091 Standard Practice for Nondestructive Measurement of Dry Film Thickness ofNonmagnetic Coatings Applied to Ferrous Metals and Nonmagnetic, Nonconductive CoatingsApplied to Non-Ferrous MetalsASTM D7393 Standard Practice for Indicating Oil in AbrasivesASTM F436/F436M Standard Specification for Hardened Steel Washers Inch and MetricDimensionsASTM F593 Standard Specification for Stainless Steel Bolts, Hex Cap Screws, and Studs
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14rovedASTM F959/F959M Standard Specification for Compressible-Washer-Type Direct TensionIndicators for Use with Structural Fasteners, Inch and Metric SeriesASTM F1554 Standard Specification for Anchor Bolts, Steel, 36, 55, and 105-ksi Yield StrengthASTM F2329 Standard Specification for Zinc Coating, Hot-Dip, Requirements for Application toCarbon and Alloy Steel Bolts, Screws, Washers, Nuts, and Special Threaded FastenersASTM F3125/F3125M Standard Specification for High Strength Structural Bolts and Assemblies,Steel and Alloy Steel, Heat Treated, Inch Dimensions 120 ksi and 150 ksi Minimum TensileStrength, and Metric Dimensions 830 MPa and 1040 MPa Minimum Tensile StrengthAWSAmerican Welding Society, 8669 NW 36 Street #130, Miami, FL 33166. www.aws.org. Term cited inForeword and Parts 1, 3, 5, 7 and 9. Standards cited include:AASHTO/AWS D1.5M/D1.5 Bridge Welding CodeAWS D1.1/D1.1M Structural Welding Code—SteelppFRAFederal Railroad Administration. www.railroads.dot.gov. Standards cited include:FRA Track Safety StandardsISOYetAInternational Organization for Standardization. www.iso.org. Standards cited include:ISO 1219-2 Fluid power systems and components – Graphical symbols and circuit diagrams – Part 2:Circuit diagramsISO 4406 Hydraulic fluid power – Fluids – Method for coding the level of contamination by solidparticlesISO 4413 Hydraulic fluid power – General rules and safety requirements for systems and theircomponentsNFPAtNotNational Fluid Power Association. www.nfpa.com. Standards cited include:NFPA/T2.24.1 Hydraulic Fluid Power - Systems Standard For Stationary Industrial Machinery Supplement To ISO 4413:1998 - Hydraulic Fluid Power - General Rules Relating To SystemsNFPA/T3.6.92 R2 Tie rod or bolted cylinder – Pressure rating supplement to NFPA/T2.6.1 R2-2000,Fluid power components – Method for verifying the fatigue and establishing the burst pressureratings of the metal pressure containing envelope of a tie rod or bolted cylinderNFPA/T3.16.3 Hydraulic Fluid Power - Requirements For Nonintegral Industrial Power UnitsNSBArafNational Steel Bridge Alliance, a division of American Institute of Steel Construction (AISC), 130 EastRandolph, Suite 2000, Chicago, IL 60601. www.steelbridges.org. Term cited in Part 3.OSHAOccupational Safety and Health Administration, 200 Constitution Avenue NW, Washington, DC 20210.www.osha.gov. Term cited in Parts 8 and 9.DSSPCThe Society for Protective Coatings. In 2021, SSPC merged with NACE (National Association ofCorrosion Engineers) to form AMPP (Association for Materials Protection and Performance). Standardscited include:SSPC-AB 1 Mineral and Slag AbrasivesSSPC-AB 2 Cleanliness of Recycled Ferrous Metallic AbrasiveSSPC-AB 3 Ferrous Metallic Abrasive
American Railway Engineering & Maintenance-of-Way AssociationLetter Ballot 15-21-14DraftNotYetApprovedSSPC-CPC 1/NACE SP21412 Corrosion Prevention and Control PlanningSSPC-CS 23.00/AWS C2.23/NACE No. 12 Joint Standard/Practice “Specification for the Applicationof Thermal Spray Coatings (Metallizing) of Aluminum, Zinc, and Their Alloys and Compositesfor the Corrosion Protection of Steel”SSPC-Guide 6 Containment of DebrisSSPC-Guide 7 Disposal of DebrisSSPC-Guide 12 Guide for Illumination of Industrial Painting ProjectsSSPC-Guide 15 Retrieval and Analysis of Soluble SaltsSSPC-PA 1 Shop, Field, and Maintenance Painting of SteelSSPC-PA 2 Determining Compliance to Required DFTSSPC-PA 17 Determining Profile ComplianceSSPC-PA Guide 4 Guide to Maintenance Repainting with Oil Base or Alkyd Painting SystemsSSPC-PA Guide 10 Contractor ESH RequirementsSSPC-QP 1 Field Industrial Contractor QualificationSSPC-QP 2 Hazardous Paint Removal Contractor QualificationSSPC-SP 1 Solvent CleaningSSPC-SP 2 Hand Tool CleaningSSPC-SP 3 Power Tool CleaningSSPC-SP 5/NACE No. 1 White Metal Blast CleaningSSPC-SP 5 (WAB)/NACE WAB-1 White Metal Wet Abrasive Blast CleaningSSPC-SP 6/NACE No. 3 Commercial Blast CleaningSSPC-SP 6 (WAB)/NACE WAB-3 Commercial Wet Abrasive Blast CleaningSSPC-SP 7/NACE No. 4 Brush-Off Blast CleaningSSPC-SP 7 (WAB)/NACE WAB-4 Brush-Off Wet Abrasive Blast CleaningSSPC-SP 10/NACE No. 2 Near-White Blast CleaningSSPC-SP 10 (WAB)/NACE WAB-2 Near-White Wet Abrasive Blast CleaningSSPC-SP 11 Bare Metal Power Tool CleaningSSPC-SP 12/NACE No. 5 Surface Preparation and Cleaning of Metals by Waterjetting Prior toCoatingSSPC-SP 14/NACE No. 8 Industrial Blast CleaningSSPC-SP 14 (WAB)/NACE WAB-8 Industrial Wet Abrasive Blast CleaningSSPC-SP 15 Commercial Grade Power-Tool CleaningSSPC-SP 16 Brush-Off Blast Cleaning of Coated and Uncoated Galvanized Steel, Stainless Steels,and Non-Ferrous MetalsSSPC-SP WJ-1/NACE WJ-1 Waterjetting to Bare SubstrateSSPC-SP WJ-2/NACE WJ-2 Very Thorough WaterjettingSSPC-SP WJ-3/NACE WJ-3 Thorough WaterjettingSSPC-SP WJ-4/NACE WJ-4 Light WaterjettingSSPC-TU 3 OvercoatingSSPC-TU 7 Conducting Ambient Air, Soil, and Water Sampling of Surface Preparation and PaintDisturbance ActivitiesSSPC-VIS 1 Guide and Reference Photographs for Steel Surfaces Prepared by Dry Abrasive BlastCleaningSSPC-VIS 2 Standard Method of Evaluating Degree of Rusting on Painted Steel SurfacesSSPC-VIS 3 Guide and Reference Photographs for Steel Surfaces Prepared by Power and Hand ToolCleaningSSPC-VIS 4/NACE VIS 7 Guide and Reference Photographs for Steel Surfaces Prepared byWaterjettingSSPC-VIS 5/NACE VIS 9 Guide and Reference Photographs for Steel Surfaces Prepared by WetAbrasive Blast Cleaning
AASHTO . American Association of State Highway and Transportation Officials, 555 12th St NW, Suite 1000, Washington, D.C. 20004. www.transportation.org. Term cited in Parts 1, 3, 5, 8 and 9. Standards cited include: AASHTO LRFD Bridge Design Specifications AASHTO Standard Specifications for Highway Bridges AASHTO/AWS D1.5M/D1.5 Bridge Welding Code
