WIXLIB

01-D5WINDOWSALUMINUMTable of ContentsSingle Hung, Fixed, andHorizontal Slider Series 8000 Series 8100 Series 8200SECTION D5PAGESPECIFICATIONS SERIES 8000, 8100, AND 8200 WINDOWS .02-D5 and 03-D5SPECIAL FEATURES SINGLE HUNG SERIES 8000 WINDOW .04-D5TYPICAL DETAILS SINGLE HUNG SERIES 8000 WINDOW .05-D5SPECIAL FEATURES FIXED SERIES 8100 WINDOW .06-D5TYPICAL DETAILS FIXED SERIES 8100 WINDOW.07-D5SPECIAL FEATURES HORIZONTAL SLIDER SERIES 8200 WINDOW .08-D5ACCESSORIES .10-D5 thru 12-D5Project: River Rock Casino Resort, British Columbia, CanadaDue to the diversity in state/provincial, local, and federal laws and codes that govern the design and application of architectural products,it is the responsibility of the individual architect, owner, and installer to ensure that products selected for use on projects comply with allapplicable building codes and laws. U.S. Aluminum exercises no control over the use or application of its products, glazing materials, andoperating hardware, and assumes no responsibility thereof.The rapidly changing technology within the architectural aluminum products industry demands that U.S. Aluminum reservethe right to revise, discontinue or change any product line, specification or electronic media without prior written notice.NOTE: Dimensions in parentheses ( ) are millimeters unless otherwise noted.Other metric units shown in this publication are:m - meterKg - kilogramPa - pascalKPa - kilopascalMPa - megapascalOnline usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5DTYPICAL DETAILS HORIZONTAL SLIDER SERIES 8200 WINDOW .09-D5

02-D5WINDOWSALUMINUMSpecificationsSingle Hung, Fixed, andSliding WindowsDSECTION 08 51 13 ALUMINUM WINDOWSQUALITY ASSURANCEDrawings and specifications are basedon Series 8000 Single Hung, 8100Fixed, or 8200 Horizontal Sliding(Specify) Thermal CW60 Windowsas manufactured by U.S. Aluminum.Whenever substitute products are tobe considered, supporting technicalliterature, samples, drawings, andperformance data must be submitted10 days prior to bid in order to makea valid comparsion of the productsinvolved. Test reports certified by anAAMA independent test laboratorymust be made available upon request.PART 1 GENERAL1.01 Work IncludedA. Furnish and install aluminumarchitectural windows completewith hardware and relatedcomponents as shown on drawingsand specified in this section.Specify glass and glazing in thissection if window assemblies are tobe glazed by the window manufacturer.If glazing is to be done by a differentcontractor, glass and glazing should bespecified in Section 08 80 00.B. Glass and Glazing1. All units shall be factory glazed.OR1. Reference Section 08 80 00 forGlass and Glazing.List work and materials related to thissection but specified in other sections.1.02 Related WorkSection 08 40 00 Entrances and StorefrontsSection 08 44 00 Glazed Curtain WallsSection 08 50 00 Windows1.03 Testing and PerformanceRequirementsA. Test Units1. Air, water, and structural test unitshall conform to requirements set Series 8000 Series 8100 Series 8200forth in ANSI/AAMA/NWWDA 101I.S. 2-97 and AAMA 910-93 orCSA A440.2. Thermal test unit sizes shall be47-1/4" x 59" (1200 x 1500) forSeries 8000 and 8100, 59"x47-1/4" (1500 x 1200) for Series8200. Unit shall consist of asingle hung, fixed or horizontalsliding window.B. Test Procedures and Performances1. Windows shall conform to allAAMA/ANSI/NWWDA-101 I.S.2-97 and AAMA 910-93 or CSAA440 requirements for the windowtype referenced in 1.01.B. Inaddition, the following specificperformance requirements shallbe met.2. Air Infiltration Test With ventilators closed andlocked, test unit in accordancewith ASTM E 283-91 at a staticair pressure difference of 6.24 psf.Air infiltration shall not exceed.30 cfm per foot of crack.3.Water Resistance Test With ventilators closed andlocked, test unit in accordancewith ASTM E 331-96/ASTM E 547at a static air pressure differenceof 12 psf. There shall be nouncontrolled water leakage.4.Uniform Load Deflection Test With ventilators closed andlocked, test unit in accordancewith ASTM E 330-97 at a static airpressure difference of 90 psfpositive and negative pressure.No member shall deflect overL/175 of its span.5. Condensation Resistance Test(CRF) - With ventilators closedand locked, test unit inaccordance with AAMA 1503.Condensation Resistance Factor(CRF) shall not be less than 49 forSeries 8100 and 8200. Not lessthan 50 for Series 8000.6. Thermal Transmittance Test(Conductive U-Value) With ventilators closed andlocked, test unit in accordancewith NFRC 100 and AAMA 1503.Conductive thermal transmittance(U-Value) for Series 8000 and8200 Windows shall have arange between 0.35 to 0.56BTU/hr/ft2/ºF and Series 8100Windows shall have a rangebetween 0.33 to 0.56BTU/hr/ft2/ºF.7. AAMA CW60 RatingTesting Procedures AAMA/WDMA/CSA 101/I.S.2/A440-8 - LaboratoryPerformance Testing. AAMA 503-08 - NewlyInstalled Fenestration Products. AAMA 511-08 - InstalledFenestration Products After6 Months.1.04 Quality AssuranceA. Provide test reports from AAMAaccredited laboratories certifyingthe performance as specified in1.05 or 11.15 of CSA A440.B. Test reports shall be accompaniedby the window manufacturer'sletter of certification, stating thetested window meets or exceedsthe referenced criteria for theappropriate AAMA/NWWDA101/I.S.2-97 and AAMA 910-93 orCSA A440 window type.1.05 SubmittalsA. Contractor shall submit shopdrawings, finish samples, testreports, and warranties.1.06 WarrantiesA. Total Window System1.The responsible contractor shallassume full responsibility andwarrant for one year thesatisfactory performance of thetotal window installation whichincludes that of the windows,hardware, glass (includinginsulating units), glazing,anchorage and setting system,sealing, flashing, etc., as it relatesto air, water, and structuraladequacy as called for in thespecifications and approvedshop drawings.Online usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5

03-D5WINDOWSALUMINUMSpecificationsSECTION 08 51 13 ALUMINUM WINDOWSSingle Hung, Fixed, andSliding WindowsPART 3 EXECUTION2.01 MaterialsA. Aluminum1. Extruded aluminum shall be6063-T5 alloy and tempered.B. Hardware1. Series 8000 and 8200 Windowshave spring loaded self-lockinglatches as supplied by U.S.Aluminum.C.Weatherstrip1. For Series 8000 and 8200Windows weatherstrip shall befin seal or equal. For Series 8100Windows all weatherstrip shall beE.P.D.M.D. Thermal Barrier1. Barrier material shall be pouredin-place two part polyurethane.To ensure that composite strengthremains unaltered during thermalcycling, a mechanical bondbetween the aluminum and thethermal filling shall be createdby mechanically abrading theextrusion thermal cavity priorto filling with the polyurethanepolymer. A non-structural thermalbarrier is unacceptable.2. Specified hardware shall notbridge the thermal barrier.E. Glass1. Insulating glass shall be () asmanufactured by () consistingof () exterior, () air spacer,and () interior.OR1. Glass shall be 1/4" (6) monolithic.2.02 FabricationA. General1. All primary aluminum frame,extrusions or vent extrusions shallhave a minimum wall thickness of.062 (1.57)2. Depth of frame 4-1/2" (114.3) for1" (25) glazing.B. Frame - Frame components shallbe mechanically fastened.C.Ventilator (Series 8000 and 8200)1. All vent extrusions shall benotched .D. Screens (Series 8000 and 8200)1. Screen frames shall have springslocking the screen in place.2. Screen mesh shall be aluminumor fiberglass. (if applicable)E. Glazing - All units shall be eithershop or field glazed.F. FinishAll exposed framing surfaces shallbe free of scratches and otherserious blemishes. Aluminumextrusions shall be given a causticetch followed by an anodic oxidetreatment to obtain. (Specify oneof the following)#11 Clear anodic coating#22 Dark Bronze anodiccoating#33 Black anodic coatingA Fluoropolymer paint coatingconforming with the requirementsof AAMA 2605. Color shall be(Specify a U.S. Aluminum standardcolor).3.01 InspectionA. Job Conditions1. Verify that openings aredimensionally within allowabletolerances, plumb, level, clean,provide a solid anchoring surface,and are in accordance withapproved shop drawings.3.02 InstallationA. Use only skilled tradesmen withwork done in accordance withapproved shop drawings andspecifications.B. Adequately anchor to maintainpositions permanently whensubjected to normal thermalmovement, specified buildingmovement, and specified windloads.C.Adjust windows for proper operationafter installation.D. Furnish and apply sealants toprovide a weather tight installationat all joints and intersections andat opening perimeters.3.03 Protection and CleaningA. After completion of windowinstallation, windows shall beinspected, adjusted, put intoworking order and left clean,free of labels, dirt, etc. Protectionfrom this point shall be theresponsibility of the generalcontractor.Online usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5DPART 2 PRODUCTS Series 8000 Series 8100 Series 8200

04-D5WINDOWSALUMINUMSpecial FeaturesSingle Hung Window Series 8000The Series 8000 Single Hung Window uses a Class 5 Balance for smooth operation. The 4-1/2" (114) deep frame isdesigned to match typical building conditions, including our entrances and storefronts. An efficient thermally insulatedframe accepts 1" (25) glazing, with extruded pulls at the interlock and bottom rail. The window features a self-lockinglatch.Tested to AAMA CW60Accepts 1" (25) GlazingThermally Insulated-NFRC CertifiedU-Factors as Low as 0.344-1/2" (114) Deep Frame to Match TypicalBuilding Conditions Choice of Block or Fin FrameD Class 5 Balance for Ease of Operation Accessories Such as Screens, Mulling Bars, Subsills,Head and Jamb Channels are Available Available in an Array of Architectural Coatingsand Anodized Finishes Complemented by the Series 8200 HorizontalSliding and Series 8100 Fixed Windows Made in the U.S.A.Single Hung WindowsOnline usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5

05-D5WINDOWSALUMINUMTypical DetailsSingle Hung Window Series 8000FOR 1" (25) GLAZINGBlock FrameInstallation Method ShownMeets or Exceeds Specifications:14 AAMA/WDMA/CSA 101/1.S.2/A 440 -08- ASTM E 283-04- ASTM E 330-02- ASTM E 331-00- AAMA 1503Opp.42533/8"(9.5)Min.A complete set of detailsin DWG format is availableat usalum.com NFRC - NFRC 100-2004- NFRC 200-2004- NFRC 500-2004Opp.5Maximum Frame Size65" x 91" (1651 x 2311)2-3/8"(60)SH8121SH886SH885 (Typ.)OPTIONAL(Typ.)DOPTIONALTYPICAL SH8652"(50.8)SH8543/8"(9.5)Min.2D.L.O.FRAME WIDTHSH866OPTIONALCC676D.L.O.FRAME 8 3/8"(9.5)Min.Online usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5D.L.O.FRAME WIDTHNOT TO SCALE

06-D5WINDOWSALUMINUMSpecial FeaturesFixed Window Series 8100The Series 8100 Fixed Window has a 4-1/2" (114) deep frame designed to match typical building conditions, includingour entrances and storefronts. An efficient thermally insulated frame accepts 1" (25) glazing. Available in an array ofarchitectural coatings and anodized finishes.Tested to AAMA CW60Accepts 1" (25) GlazingThermally Insulated-NFRC CertifiedU-Factors as Low as 0.344-1/2" (114) Deep Frame to Match TypicalBuilding Conditions Choice of Block or Fin Frame Accessories Such as Mulling Bars, Subsills,Head and Jamb Channels are Available Available in an Array of Architectural Coatingsand Anodized Finishes Made in the U.S.A.D Fixed WindowOnline usalum.com By Phone (800) 262-5151Online crlaurence.com By Phone (800) 421-6144D5