Transcription
7130LBR Series Layer 1 Application SwitchData SheetProduct HighlightsOverviewPerformanceThe Arista 7130LBR Series introduces a fully composable architecture for the nextgeneration of high performance in-network applications. Combining programmablelarge-scale FPGAs with a full-featured R3 family switch chip, all connected throughan ultra-low latency layer 1 crosspoint. With native support for 1:N connectivity andand replication, each front-panel lane can be connected to any combination of twoFPGAs and the switch chip enabling customers to combine multiple applicationsand utilise the inherent capabilities of the switching silicon. 7130LBR: 48 x SFP , 6 x QSFP-DD (NRZ) 96 x 10GbE, 18 x 25GbE internal switchinterfaces Up to 1.5 Tbps L2/L3 forwarding L1 replication from 6ns Dual Xilinx Virtex UltraScale FPGAsCore Features Ultra low latency layer 1 crosspoint Full-featured integrated switch Dual application FPGAs High performance x86 control-planeAdvanced L1 Functionality Signal regeneration Media conversion Port mirroring Telemetry Dynamic patching/link management Layer 1 statistics on each linkIntegrated SwitchFeaturing dual Virtex UltraScale FPGAs, the 7130LBR Series supports two parallelapplication instances based on Arista’s LB Board Standard. Arista applicationsincluding MetaMux for low latency multiplexing and MetaWatch for picosecondlevel time stamping can be combined with third party applications and customfunctionality developed with the EOS FPGA Development Kit (FDK). The FDK buildsupon EOS’s extensible architecture and includes example code and IP cores toaccelerate new projects.The 7130LBR Series includes an R3 generation switch element supporting line-rateL2/L3 forwarding and a complete set of advanced routing features. Using the layer 1crosspoint, these switch ports can be exibly con gured in-band or out-of-band. Inband ports enable high-bandwidth switching & routing capability, and out-of-bandports provide rich streaming telemetry, o oading FPGA resources. The switch canalso be con gured in tap aggregation mode, leveraging the Arista DANZ feature set.The 7130LBR is available in a space-saving 1RU form factor with 48 x SFP and 6 xQSFP-DD interfaces (NRZ). Each QSFP-DD interface may be broken out to 2 x 40GbEor 8 x 10GbE interfaces, for a total of 96 x 10G lanes. Wire-speed L2/L3 forwarding BGP/OSPF/PIM support LANZ for microburst detection 4 GB packet bu er Tap aggregation mode Precision time stamping Streaming telemetryRedundancy & Data Center Optimized High-density, compact 1RU form-factor Dual redundant, hot swappable PSU Dual redundant, hot swappable fans AC & DC power options Rear to front or front to rear coolingArista Extensible Operating Systemfifflflfffifi Single binary image for all products Fine-grained truly modular network OS Stateful Fault Containment (SFC) Stateful Fault Repair (SFR) Full Access to Linux shell and tools Extensible platform - bash, python, C ,GO, OpenCon g FPGA Development Kit for custom innetwork applicationsArista 7130LBR-48S6QD: 48x SFP , 6 x QSFP-DD portsArista EOSAll Arista products including the 7130LBR Series run the same Arista EOS software,simplifying network administration with a single standard across all switches. AristaEOS is a modular switch operating system with a unique state sharing architecturethat cleanly separates switch state from protocol processing and application logic.Built on top of a standard Linux kernel, all EOS processes run in their own protectedmemory space and exchange state through an in-memory database. This statesharing architecture provides the foundation for self-healing resiliency and enablesstraightforward third-party development and application integration.Arista EOS enables advanced monitoring and automation capabilities such as ZeroTouch Provisioning, LANZ, and Linux based tools to be run natively on the switch.
7130LBR Series Platform OverviewData SheetComposable ArchitectureTo address dynamic application requirements, the 7130LBR features a composable architecture centered around a high-density layer 1crosspoint. Through the crosspoint any front-panel port can be linked 1:1 or mirrored to any of the platform components. The R-Seriesswitch can be used as a standard in-band device, or tra c can be replicated to it for counters and streaming telemetry. FPGAs supportArista’s 7130 applications, third-party developed images and customer applications.Arista 7130LBR-48S6QD System Architecture7130 FPGA ApplicationsArista o ers several powerful network applications to simplify and transform network infrastructure. These applications are designed foruse cases including ultra-low latency exchange trading, network visibility and vendor- or broker-based shared services. Theseapplications enable a complete lifecycle of networking functions, such as packet replication, multiplexing, ltering, time stamping,aggregation and capture.ApplicationOverviewKey FeaturesUse it for.MetaWatchAdvanced networkmonitoring TappingLarge scale, lossless tap aggregationMulti-port data captureSub-nanosecond precise time stampingDeep bu ering (32 GB) In-depth network monitoring andvisibility Improved network reliability &troubleshooting problems Market data & packet capture Accurate latency measurement &monitoring Regulatory compliance (MiFID II - RTS 25)MetaMuxLow-latencymultiplexing Data aggregation in 39 nanosecondsDeterministic jitterPacket statisticsBGP & PIM support Ultra-low latency network connectivityfor trading Market data fan-out and dataaggregation for order entry atnanosecond levelsMultiAccess* Connection sharing Low-latency multiplexing and securitywith enhancedsecurityExchange*In-line packet timestamping enablingexchange fairness Secure network connection sharingfrom 55 nanoseconds Providing sponsored access to multipleclients ACL-based con gurable ltering Easy to deploy data privacy for connection Multi tenant exchange accesssharing Low latency interconnect sharing Timestamp at the edge of trading venuenetworks Enabled by reliable accuracy Time/latency in the venueimplementation becomes less relevant Increase exchange fairness Reduce trading venue latency sensitivityfiffifififfff* Not currently supported in EOS
7130LBR Series Platform OverviewData SheetCustom Applications & FPGA Development KitFPGA developers can write custom applications for the 7130LBR Series with Arista’s FPGA Development Kit (FDK). The FDK includes APIdocumentation, sample code, and IP cores to streamline development. Arista development toolkits enable complete and unfetteredaccess to the facilities provided by the in-system FPGAs.IP CoreFeatures10GbE MAC/PHY Ultra low latency 10GbE ethernet PCS/PMA and MAC10GbE & 1GbE supportAXI4 stream interfaceRegister interface for counters and link status25GbE MAC/PHY Ultra low latency 25GbE ethernet PCS/PMA and MAC25GbE supportAXI4 stream interfaceRegister interface for counters and link statusTimestamper Complete precision timestamping systemIncludes timestamper core sync & control daemonPPS synchronizationExample Start-of-Frame timestamping applicationMux 10GbE packet multiplexerCon gurable scheduling algorithmsAdvanced eXtensible Interface (AXI4) streaming inputsStatus and packet countersStorm controlPrecision Timing (IEEE 1588v2 and PPS)To meet the stringent timing and synchronization requirements in nancial markets, telecom, and media & entertainment networks,Arista’s 7130LBR delivers high precision in-band time and frequency distribution support via Precision Time Protocol (PTP, IEEE 1588v2)with optional Pulse-Per-Second (PPS) inputs for added accuracy. Leveraging a high stability on-board oscillator, 7130LBRs can achievepicosecond-level time synchronization.The 7130LBR features two front-panel SMA PPS inputs, with optional primary/secondary failover for added resiliency. An internal PPSdistribution network delivers PPS signals to each application FPGA. Two front-panel SMA outputs can forward PPS or output theinternal 10Mhz clock to downstream systems.High Availability and FlexibilityThe Arista 7130LBR Series were designed for exible deployment and continuous operations with system wide monitoring of bothhardware and software components, simple serviceability and provisioning to prevent single points of failure.Key features include:fiflfifi AC and DC power supply options Front to Rear cooling with dynamic temperature control. Redundant, color coded, eld serviceable power and cooling subsystems: 1 1 hot-swappable platinum rated power supplies N 1 hot-swappable fans Live software patching Self healing software with Stateful Fault Repair (SFR)
Data SheetIntegrated R3-Series SwitchThe integrated switch in the 7130LBR Series o ers a wide range of features for di erent applications. When connected directly to thefront-panel interfaces through the crosspoint, it provides high-performance switching and routing capable of 2.4 Tbps of throughput.Its deep bu er virtual output queue (VOQ) architecture eliminates head-of-line (HOL) blocking and virtually eliminates packet dropseven in the most congested network scenarios. An advanced tra c scheduler fairly allocates bandwidth between all virtual outputqueues while accurately following queue disciplines including weighted fair queueing, xed priority, or hybrid schemes. As a result, theR3-Series switch can handle the most demanding data center requirements with ease, including mixed tra c loads of real-time,multicast, and storage tra c while still delivering low latency.Using the crosspoint to mirror front-panel tra c, the switch can also be used out-of-band for monitoring layer 1 paths or FPGA links,saving valuable FPGA logic. In tap aggregation mode, the switch supports time stamping, tra c steering, and N:M mirroring witharbitrary aggregation groups.FlexRouteTMThe Arista FlexRoute Engine provides support for the full internetrouting table, in hardware, with IP forwarding at Layer 3 and withsu cient headroom for future growth in both IPv4 and IPv6 routescale to more than 1.4 million routes. The innovative FlexRouteEngine with its patented algorithmic approach to building layer 3forwarding tables on Arista R-Series Universal Spine and Leafplatforms is unique to Arista and a key enabler in calling theseplatforms routers.R-Series Switch Pro lesAccelerated sFlowSFlow is a powerful tool used commonly by network operators foradvanced network telemetry, capacity planning, security analysisand quality of experience monitoring. Traditional sFlow utilizes asystem CPU for processing samples of hundreds of thousands ofows. In modern high performance systems guaranteed high ratesampling requires the capability to both sample and process packetrates of billions of packets per second. With the R-Series AcceleratedsFlow feature, the sampling and processing of ow samples intosFlow datagrams is handled via integrated sFlow engines capable ofsupporting 1:500 sampling rates on full wire speed systems orhigher rates with selective sampling based on triggers and lters. AllsFlow v5 information is included in the sFlow records ensuringconsistent integration with existing standard sFlow collection andanalysis tools and no loss of information.Pro leL3BalancedARP Entries88k80kMAC Addresses224k224kIPv4 Unicast Routes1450k800kAdditional IPv4 UnicastRoutes with FlexRoute 1792k 1792kIPv6 Unicast 2-Way512-WayMulticast RoutesTCAM ACL Entries(Per chip)Tra c Policy ACL IPv4Pre xesTra c Policy ACL IPv6Pre xesECMPIn-band Network fiffiffiIn-band network telemetry, or INT, is a standards-based approach to providing deep visibility into tra c in real-time, with no impact onswitch performance. INT provides per- ow monitoring of tra c drops, latency, congestion and the network path. INT information canbe exported in IPFIX or sFlow formats to a management system or collector such as Arista CloudVision, for predictive analytics and deepforensics to measure latency per device and across the network, trace packets and reconstruct path topology as well as detecting hotspots. In-band Network Telemetry is available on the R-Series switch, with the ability to originate, pass and terminate, along withmirroring to external collectors.ffifl7130LBR Series Switch Features
7130LBR Series Switch FeaturesData SheetLayer 2 Features 802.1w Rapid Spanning Tree802.1s Multiple Spanning Tree ProtocolRapid Per VLAN Spanning Tree (RPVST )4096 VLANsQ-in-Q802.3ad Link Aggregation/LACP 256 Ports / Channel 1024 groups per system (subject to system density)MLAG (Multi-Chassis Link Aggregation) Uses IEEE 802.3ad LACP 512 ports per MLAG802.1Q VLANs/Trunking802.1AB Link Layer Discovery Protocol802.3x Flow Control *Jumbo Frames (9216 Bytes)IGMP v1/v2/v3 snoopingStorm ControlLayer 3 Features Static RoutesRouting Protocols: OSPF, OSPFv3, BGP, MP-BGP, IS-IS, and RIPv2BGP FlowSpec, BMP, BGP-RPKI, PIC512-way Equal Cost Multipath Routing (ECMP)VRF, Inter-VRF Route LeakingBi-Directional Forwarding Detection (BFD)Unicast Reverse Path Forwarding (uRPF)VXLAN Bridging and RoutingVRRPVirtual ARP (VARP)Policy Based Routing (PBR)Route MapsRCFMulticast IGMP v2/v3MLD v2Protocol Independent Multicast (PIM-SM / PIM-SSM)PIM-BiDir *Anycast RP (RFC 4610)Multicast Source Discovery Protocol (MSDP)Advanced Monitoring and Provisioningfifififififififi Latency Analyzer and Microburst Detection (LANZ) Con gurable Congestion Noti cation (CLI, Syslog) Streaming Events (GPB Encoded)ZeroTouch Provisioning (ZTP) AdvancedMirroring PortMirroring(14 sessions) EnhancedRemotePort Mirroring SPAN/TAPM:NAggregation L2/3/4 FilteringPost-cardTelemetry Advanced Event Management suite (AEM) CLI Scheduler Event Manager Event Monitor Linux tools Integrated packet capture/analysis with TCPDump Restore and Con gure from USB RFC 3176 sFlowMPLS Support LDP, RSVP-TE, Segment Routing (SR), SR-TE, BGP-LU, BGP-LS,TE-FRR, TI-LFA L3VPN, 6PE/6vPE, L2VPN - EoMPLS PWEs, VPLS*, EVPN-MPLSGateway EVPN (L2 and L3), EVPN-MPLS, EVPN A-A, EVPN-VPWS, EVPNDCI*, EVPN-MulticastSecurity Features Control Plane Protection (CPP)Ingress / Egress ACLs using L2, L3, L4 eldsIngress / Egress ACL Logging and CountersMAC ACLsACL Deny LoggingACL CountersAtomic ACL Hitless restartDHCP Relay / SnoopingMACsec (802.1AE)TACACS RADIUSARP trapping and rate limitingQuality of Service (QoS) Features Up to 8 queues per portStrict priority queueing802.1p based classi cationDSCP based classi cation and remarkingEgress shaping / Weighted round robin (WRR)WFQ, CIR*, ETS*, Fixed PriorityPolicing / Shaping, H-QoSExplicit Congestion Noti cation (ECN) marking802.1Qbb Per-Priority Flow Control (PFC)Network Management CloudVisionCon guration rollback and commitSNMP v1, v2, v3Management over IPv6Telnet and SSHv2SyslogAAAIndustry Standard CLISystem LoggingEnvironment monitoring
7130LBR Series Switch FeaturesData SheetPrecision Timing SNMP MIBsSynchronous Ethernet with ESMCIEEE 1588-2008 PTP T-GM, T-BC, T-TSCG.8275.1, G.8275.2G.8261, G.8264System Scalability 9216 Byte Jumbo Frame Support 8 Priority Queues per Port Large Scale Link Aggregation Groups (LAG) 1024 x 16 Ports per LAG 64 x 256 Ports per LAG Virtual Output Queueing Distributed SchedulerStandards Compliance 802.1D Bridging and Spanning Tree802.1p QOS/COS802.1Q VLAN Tagging802.1w Rapid Spanning Tree802.1s Multiple Spanning Tree Protocol802.1AB Link Layer Discovery Protocol802.3ad Link Aggregation with LACP802.3x Flow Control802.3ab 1000BASE-T802.3z Gigabit Ethernet802.3ae 10 Gigabit Ethernet802.3ba 40 Gigabit EthernetRFC 2460 Internet Protocol, Version 6 (IPv6)RFC 2461 Neighbor Discovery for IP Version 6 (IPv6)RFC 2462 IPv6 Stateless Address Autocon gurationRFC 2463 Internet Control Message Protocol (ICMPv6)IEEE 1588-2008 Precision Time Protocol RFC 3635 EtherLike-MIBRFC 3418 SNMPv2-MIBRFC 2863 IF-MIBRFC 2864 IF-INVERTED-STACK-MIBRFC 2096 IP-FORWARD-MIBRFC 4363 Q-BRIDGE-MIBRFC 4188 BRIDGE-MIBRFC 2013 UDP-MIBRFC 2012 TCP-MIBRFC 2011 IP-MIBRFC 2790 HOST-RESOURCES-MIBRFC 3636 RFC 4273 BGP4-MIBRFC 4750 RFC 2787 MP Authentication Failure trapENTITY-SENSOR-MIB support for DOM (Digital OpticalMonitoring) User con gurable custom OIDsSee EOS release notes for latest supported MIBsfifi1. Supported for internal switch interfaces.2. FPGA-to-Switch lanes only. Front-panel lanes are 10G NRZ.
7130LBR Series Technical Speci cationsData SheetSpeci cationsSwitch Model7130LBR-48S6QDFront-Panel Ports48x SFP , 6x QSFP-DD (10G NRZ)Layer 1 Throughput100M-11.3Gbps per laneLayer 1 LatencyFrom 6 nsFPGA2x Xilinx UltraScale VU9P-3FPGA DRAM32GB DDR4 per FPGAFPGA Crosspoint Interfaces48x 10GbE per FPGAR-Series Switch Throughput1.5 TbpsR-Series Switch Packet Bu er4 GB9x 25GbE lanes to each FPGA48x 10GbE lanes to crosspoint4x 10GbE to CPUInternal Switch InterfacesFPGA Development Kit (FDK)YesVitis Development Kit (VDK)Yes1ClockOCXOCPU8-core x86System DRAM / SSD64 GB / 120 GBRS-232 Serial Ports1 (RJ-45)USB Ports1100/1000 Management Ports1PPS Input Ports (5V TTL, 50Ω or Hi-Z)2PPS Output Ports (5V TTL)2Hot-swap Power Supplies2 (1 1 redundant)Hot-swappable Fans3 (N 1 redundant)Reversible Air ow OptionYesTypical/Max Power Draw 2TBDRack Units1U17.32 x 1.73 x 25.75 inches(44.0 x 4.4 x 65.4 cm)Size (WxHxD)Weight32.9 lbs (14.9 kg)Fan TrayFAN-7011HPower SuppliesPWR-1511-AC or PWR-1511-DCEOS Feature LicensesGroup 4Minimum EOS4.28.0Ffiffflfi1. Not currently supported in EOS2. Typical power consumption measured at 25C ambient with 50% load
7130LBR Series Technical Speci cationsData SheetEnvironmental CharacteristicsPower Supply Speci cationsOperating TemperaturePower SupplyStorage Temperature0 to 40 C (32 to 104 F)-40 to 70 C (-40 to 158 F)Relative Humidity5 to 95%Operating Altitude0 to 10,000 ft, (0-3,000m)ImmunityEN55024, EN55035EN300 386SafetyUL/CSA 60950-1, EN 62368-1, IEC-62368-1, IEC60950-1CB Scheme with all country di erencesCerti cationsNorth America (NRTL)European Union (EU)BSMI (Taiwan)C-Tick (Australia)CCC (PRC)KC (S. Korea)EAC (Eurasian Customs Union)VCCI (Japan)EuropeanUnionDirectives2014/35/EU Low Voltage Directive2014/30/EU EMC Directive2012/19/EU Waste Electrical and ElectronicEquipment (WEEE) Directive2011/65/EU Restrictions of HazardousSubstances (RoHS) Directive2015/863/EU Commission Delegated Directive(EU)fiEMCffPWR-1511-DC200-240V AC-48 to -60 VDC9.6A35.2A Max (-48V)Input Frequency50/60HzDCOutput Power1500W1500WIEC 320-C13AWG #6 Max93% Platinum92%Input VoltageTypical Input CurrentInput ConnectorEmissions: FCC, EN55032, EN61000-3-2,EN61000-3-3fififfiStandards CompliancePWR-1511-ACE ciency (Typical)
7130LBR Series OpticsArista Optics and CablesThe Arista 7130LBR Series supports a wide range of pluggable optics and cables. For details about the di erent optical modules andthe minimum EOS Software release required for each of the supported optical modules, visit bles.Supported Optics and CablesSupported Optics and CablesInterface TypeQSFP-DD (NRZ) Ports10GbE400GBASE-CR8 1QSFP-DD to QSFP-DD: 1m-2.5m lengths10GBASE-CRSFP to SFP : 0.5m-5m lengths200GBASE-CR4 1QSFP-DD to 2xQSFP: 1m to 2.5m lengths10GBASE-AOCSFP to SFP : 3m-30m lengths100GBASE-CR4 1QSFP-DD to 2xQSFP: 1m to 3m lengths10GBASE-SRL100m OM3 /150m OM4 Duplex MMF100GBASE-CR2 1QSFP-DD to 4xQSFP: 1m to 3m lengths10GBASE-SR300m OM3 / 400m OM4 Duplex MMF50GBASE-CR 1QSFP-DD to 8xQSFP: 1m to 3m lengths10GBASE-LRL1km Duplex SM25GBASE-CR 1QSFP-DD to 8xSFP: 1m to 3m lengths10GBASE-LR10km Duplex SM10GBASE-CRQSFP to 4xSFP : 0.5m-5m lengths10GBASE-ER40km Duplex SM40GBASE-CR4QSFP to QSFP : 0.5m-5m lengths10GBASE-ZR80km Duplex SM40GBASE-AOC3m to 100m lengths40GBASE-UNIV150m OM3 / 150m OM4, 500m SM40GBASE-SRBD100m OM3 /150m OM4 Duplex MMF40GBASE-SR4100m OM3 /150m OM4 Parallel MMF40GBASE-XSR4300m OM3 /400m OM4 Parallel MMF40GBASE-PLRL41km (1km 4x10G LR/LRL)40GBASE-PLR410km (10km 4x10G LR/LRL)40GBASE-LRL41km Duplex SM40GBASE-LR410km Duplex SM40GBASE-ER440km Duplex SMSFP ports10GBASE-TUp to 30m over Cat6a10GBASE-DWDM80km Duplex SM1GbE SX/LX/TX550m / 10km / 100mffff1. 7130LBR QSFP-DD ports operate as 8 x 10G NRZ lanes only. Breakout cables can be used to expose each lane in di erent groupings and do not addhigher speed support.
7130LBR Series Ordering InformationData SheetProduct NumberProduct DescriptionDCS-7130LBR-48S6QD-FArista 7130 Series, with 48 SFP , 6 QSFP-DD, Layer 1 X-point, 2x VU9P-3 FPGA, R series switch, front-to-rear air, 2xACDCS-7130LBR-48S6QD-RArista 7130 Series, with 48 SFP , 6 QSFP-DD, Layer 1 X-point, 2x VU9P-3 FPGA, R series switch, rear-to-front air, 2xACDCS-7130LBR-48S6QD#Arista 7130 Series, with 48 SFP , 6 QSFP-DD, Layer 1 X-point, 2x VU9P-3 FPGA, R series switch, con gurable fans & psuLIC-FIX-4-EEnhanced L3 License for Arista Group 4 Fixed switches, (BGP, OSPF, ISIS, PIM, NAT)LIC-FIX-4-VVirtualization license for Group 4 Arista Fixed switches (VMTracer and VXLAN)LIC-FIX-4-V2EOS Extensions, Security and Partner Integration license for Arista Group 4 Fixed switchesLIC-FIX-4-ZMonitoring & Automation license for Arista Group 4 Fixed switches (ZTP, LANZ, TapAgg, OpenFlow)LIC-FIX-4-FLX-LLIC-FIX-4-FLXFLX-Lite License for Arista Fixed switches Group 4 - Full Routing Up to 256K Routes, EVPN, VXLAN, SR, base MPLS LSR(no TE or link/node protection)FLX License for Arista Fixed switches Group 4 - Full Routing Up to 2M Routes, 24K ACL, EVPN, VXLAN, SR, Adv MPLSLSR with TE or link/node protectionOptional Components and SparesArista PSU, 1RU, AC, 1500W, REVERSE, 73.5MMPWR-1511-DC-REDArista PSU, 1RU, DC/DC, 1500W, FORWARD, 73.5MMPWR-1511-DC-BLUEArista PSU, 1RU, DC/DC, 1500W, REVERSE, 73.5MMFAN-7011H-FSpare fan module for Arista 7000 Series 1RU High Speed Fan (front-to-rear air ow)FAN-7011H-RSpare fan module for Arista 7000 Series 1RU High Speed Fan (rear-to-front air ow)KIT-7101-DSpare accessory kit (v3) for Arista tool-free switches with deep chassis adapters, C13/14 power cords (2-Post ears notincluded)KIT-7101-RKSpare 4-post tool-less rail kit (v3). (Compatible with KIT-ADJ-RLR)KIT-7101-LD-RKExtended length 4-post tool-less rail kit (v3), includes adapters for deep chassisKIT-ADJ-RLRSpare adapters for deep tool-free switches (pair) (Compatible with KIT 7101/7102 only)KIT-GND-EXT-1RUArista 7000 Series 1RU Ground Extender Kit for NEBS compliance (All 7280R3 1RU models)fiPWR-1511-AC-BLUEflArista PSU, 1RU, AC, 1500W, FORWARD, 73.5MMflPWR-1511-AC-RED
7130LBR Series Contact InformationData SheetWarrantyThe Arista 7130LBR series switches come with a one-year limited hardware warranty, which covers parts, repair, or replacement with a10 business day turn-around after the unit is received.Service and SupportSupport services including next business day and 4-hour advance hardware replacement are available. For service depot locations,please see: tSales5453 Great America ParkwaySanta Clara, California opyright 2022 Arista Networks, Inc. The information contained herein is subject to change without notice. Arista, theArista logo and EOS are trademarks of Arista Networks. Other product or service names may be trademarks or service marksof others.www.arista.comJune 1st, 202204-0036-01
crosspoint, these switch ports can be flexibly configured in-band or out-of-band. In-band ports enable high-bandwidth switching & routing capability, and out-of-band ports provide rich streaming telemetry, offloading FPGA resources. The switch can also be configured in tap aggregation mode, leveraging the Arista DANZ feature set.
