Transcription
Data SheetVIAVICellAdvisor JD745B Base Station Analyzer SpecificationsSpectrum Analyzer (standard)FrequencyFrequency range100 kHz to 4 GHzFrequency accuracy (Readout frequency x Internal 10MHz Frequencyreference accuracy RBW centering 2 Hz 0.5 xHorizontal resolution)Internal 10 MHz Frequency ReferenceAccuracy 0.05 ppm aging (0 to 50 C) 0.01 ppm, after 15 minutes of GPS Lock (0 to 50 C)Aging 0.5 ppm/yearFrequency SpanRange0 Hz (zero span)10 Hz to full spanResolution1 HzSpectrum Analyzer: 100 kHz to 4 GHzResolution Bandwidth (RBW)–3 dB bandwidth1 Hz to 3 MHzAccuracy 10% (nominal)1-3-10 sequenceCable and Antenna Analyzer:5 MHz to 4 GHz1-3-10 sequencePower Meter: 10 MHz to 4 GHzVideo Bandwidth (VBW)–3 dB bandwidth1 Hz to 3 MHzAccuracy 10% (nominal)Single Sideband (SSB) Phase NoiseFc 1 GHz, RBW 10 kHz, VBW 1 kHz, RMS detectorCarrier Offset30 kHz100 kHz1 MHz –90 dBc/Hz (typical) –95 dBc/Hz (typical) –102 dBc/Hz (typical)JD745B specifications apply under these conditions:y The instrument has been turned on for at least15 minutesy The instrument is operating within a validcalibration periodMeasurement RangeDANL to 20 dBmInput attenuatorrangeSpecification Conditions0 to 50 dB, 5 dB stepsMaximum Input Levely Data with no tolerance are considered typicalvaluesAverage continuouspower 20 dBmDC voltage 50 V DCy Cable and antenna measurements apply aftercalibration to the OSL standardy Typical and nominal values are defined as:– Typical: expected performance of theinstrument operating at 20 to 30 C afterbeing at this temperature for 15 minutes– Nominal: a general, descriptive termor parameter
Displayed Average Noise Level (DANL)Spurious1 Hz RBW, 1 Hz VBW, 50 Ω termination, 0 dB attenuation,RMS detectorInherent residual responseInput terminated, 0 dB attenuation, preamplifier off, RBW at 10 kHz,Sweep modePreamplifier Off10 MHz to 2.3 GHz 2.3 GHz to 3 GHz 3 GHz to 4 GHz–140 dBm (–146 dBm, typical)–138 dBm (–144 dBm, typical)–135 dBm (–140 dBm, typical)Preamplifier On10 MHz to 2.3 GHz 2.3 GHz to 3 GHz 3 GHz to 4 GHz–155 dBm (–160 dBm, typical)–153 dBm (–158 dBm, typical)–150 dBm (–156 dBm, typical)Display RangeLog scale and units(10 divisionsdisplayed)1 to 20 dB/division in 1 dB stepsdBm, dBV, dBmV, dBµVLinear scale and units(10 divisions displayed)V, mV, mW, WDetectorsNormal, positive peak, sample,negative peak, RMSNumber of traces6Trace functionsClear/write, maximum hold, minimum hold,capture, load view on/off, trace mathTotal Absolute Amplitude AccuracyPreamplifier off, power level –50 dBm, auto-coupled (20 to 30 C)5 MHz to 4 GHz 1.25 dB, 0.5 dB(typical)Attenuation 40 dB 1.55 dB, 1.0 dB(typical)Attenuation 40 dBReference LevelSetting range–120 to 100 dBmSetting ResolutionLog scaleLinear scale0.1 dB1% of reference level20 MHz to 3 GHz–90 dBm (nominal) 3 GHz to 4 GHz–85 dBm (nominal)Exceptions –70 dBm at 85.6MHz/ 227.88/ 770.4/ 1791.8/2647.8/ 2927.3/ 3195.2/ 3915.1/ 3640 MHzInput-related spurious –67 dBc (nominal)Dynamic Range2/3 (TOI-DANL) in1 Hz RBWSweep TimeRange80 ms to 1000 s24 µs to 200 sSpan 0 Hz (zero span)Accuracy 2%Span 0 Hz (zero span)ModeContinuous, singleGated SweepTrigger sourceExternal, video, and GPSGate length1 µs to 100 msGate delay0 to 100 msTriggerTrigger sourceFree run, video, external, GPSTrigger DelayRangeResolution0 to 200 s6 µsMeasurements*Channel powerOccupied bandwidthSpectrum emission maskAdjacent channel powerSpurious emissionsMarkersMarker typesNormal, delta, delta pair, noise,frequency count markerField strengthNumber of markers6Marker functionsPeak, next peak, next peak left, next peak right,minimum search marker tocenter/start/stop, always peak on/offRoute mapRF Input VSWR20 MHz to 4 GHz 95 dB1.5:1 (typical)Second Harmonic DistortionMixer level–25 dBm10 MHz to 1.3 GHz –65 dBc (typical) 1.3 GHz to 4 GHz –70 dBc (typical)Third-Order Inter-Modulation (third-order intercept: TOI)200 MHz to 2 GHz 10 dBm (typical) 2 GHz to 4 GHz 12 dBm (typical)2 CellAdvisor JD745B Base Station Analyzer SpecificationsAM/FM audio demodulationPIM detectionDual spectrum* CW signal generator (Option 003) can be set up simultaneously.
Cable and Antenna Analyzer (standard)RF Power Meter (standard)General ParametersFrequency5 MHz to 4 GHzDisplay range100 to 100 dBmResolution10 kHzOffset range0 to 60 dBAccuracy 25 ppm aging (20 to 30C )Resolution0.01 dB or 0.1 x W (x m, u, p)Aging 5 ppmRangeData Points126, 251, 501, 1001Measurement Speed1.65 ms/point (nominal)Measurement AccuracyInternal RF Power SensorFrequency range10 MHz to 4 GHzSpan100 kHz to 100 MHzDynamic range–120 to 20 dBmMaximum power 20 dBmAccuracySame as spectrum analyzerExternal RF Power SensorsCorrected directivity40 dBDirectionalJD731BJD733AReflection uncertainty (0.3 20log (1 10-EP/20) ) (typical)EP directivity – measured return lossFrequency range300 MHz to3.8 GHz150 MHz to 3.5 GHzDynamic range0.15 to 150 W (average)4 to 400 W (peak)0.1 to 50 W(average)0.1 to 50 W (peak)Connector typeType-N female on both endsMeasurement typeForward/reverse average power,forward peak power, VSWRAccuracy (4% of reading 0.05 W)1,2TerminatingJD732BFrequency range20 MHz to 3.8 GHzDynamic range–30 to 20 dBmConnector typeType-N maleMeasurement typeAverageAccuracy 7%1Output PowerHigh0 dBm (typical)Low–30 dBm (typical)Dynamic RangeReflection60 dBMaximum Input LevelAverage continuous power 25 dBm (nominal)DC voltage 50 V DCInterference ImmunityOn channelOn frequency 17 dBm at 1.4 MHz from carrier frequency (nominal)0 dBm within 10 kHz from the carrierfrequency (nominal)JD734BPeakJD736BAverageand peakMeasurementsReflection (VSWR)VSWR rangeReturn loss rangeResolutionDistance to Fault (DTF)Vertical VSWR rangeVertical return loss rangeVertical resolutionHorizontal rangeHorizontal resolutionCable Loss (1-port)RangeResolution1 to 650 to 60 dB0.011 to 651 to 60 dB0.010 to (# of data points – 1) x horizontalresolutionMaximum 1500 m (4921 ft)(1.5 x 108) x (VP)/deltaVP propagation velocityDelta stop freq – start freq (Hz)0 to 30 dB0.01 dBOptical Power Meter (Standard)Optical Power MeterDisplay range–100 to 100 dBmOffset range0 to 60 dBResolution0.01 dB or 0.1 mWExternal Optical Power SensorsMP-60A780 to 1650 nmMax permitted input level 10 dBmConnector typeType-N female on both endsConnector inputUniversal 2.5 and 1.25 mmAccuracy 5%1. CW condition at 25 C 10 C2. Forward power1-Port PhaseRangeResolution–180 to 180 0.01 Smith ChartResolution0.013 CellAdvisor JD745B Base Station Analyzer SpecificationsMP-80AWavelength range 23 dBm
2-Port Transmission Measurements(Option 001)FrequencyFrequency range5 MHz to 4 GHzFrequency resolution10 kHzTransmission uncertaintyGPS Receiver and Antenna (Option 010)GPS IndicatorLatitude, longitude, altitudeHigh-Frequency AccuracySpectrum, interference, and signal analyzerGPS lock 10 ppbHold over (for 3 days) 50 ppb(0 to 50 C)ConnectorSMA, female15 minutes aftersatellite lockedInterference Analyzer (Option 011)MeasurementsSpectrum analyzerSound indicator, AM/FM audiodemodulation, interference ID,spectrum recorderSpectrogramCollect up to 72 hours of dataRSSICollect up to 72 hours of dataInterference finderUse 5 dB attenuators on both ports to lessen uncertainty.Spectrum replayerDual spectrogramOutput PowerHigh0 dBm (typical)Low–30 dBm (typical)Measurement SpeedVector2.2 ms/point (nominal)Dynamic RangeVector5 MHz to 3 GHz, 80 dB 3 GHz to 4 GHz, 75 dBScalar5 MHz to 4 GHz, 100 dBMeasurementsInsertion Loss/GainRangeResolution–120 to 100 dB0.01 dB2-Port PhaseRangeResolution–180 to 180 0.01 Bias-Tee (Option 002)VoltageVoltage range 12 to 32 VVoltage resolution0.1 VPower8 W MaxCW Signal Generator (Option 003)FrequencyFrequency range25 MHz to 4 GHzFrequency reference 25 ppm MaximumFrequency resolution10 kHzOutput PowerRange0 dBm, –30 to –80 dBmStep1 dBAccuracy 1.5 dB, (0 dBm, -30 to -70 dBm) 2.5 dB (-70 to -80 dBm)(15 to 35 C)4 CellAdvisor JD745B Base Station Analyzer SpecificationsChannel Scanner (Option 012)Frequency Range10 MHz to 4 GHzMeasurement Range-110 to 20 dBmMeasurementsChannel scanner1 to 20 channelsFrequency scanner1 to 20 frequenciesCustom scanner1 to 20 channels or frequenciesBluetooth Connectivity (Option 013)Personal area network (PAN)File transfer profile (FTP)WiFi Connectivity (Option 016)MeasurementsInterface typeUSB LAN cardInterface standardIEEE 802.11 b/g/nChipsetRealTek, RalinkUSB wireless modeInfrastructure modeWeb-based remote controlInternet Exporer, Chrome, SafariInternet protocol versionIPvc4, IPv6
cdmaOne/cdma2000 Signal Analyzer (Options 020 and 040)General ParametersFrequency rangeBand 0 to 10Input signal level–40 to 20 dBmRF channel power accuracy 1.0 dB (typical)CDMA compatibilitycdmaOne and cdma2000Frequency error 10 Hz ref freq accuracy99% confidence levelRho accuracy 0.0050.9 Rho 1.0Residual Rho 0.995 (typical)PN offset1 x 64 chipsCode domain power 0.5 dB relative power 1.5 dB absolute powerPilot power accuracy 1.0 dB (typical)Time offset 1.0 µs, 0.5 µs (typical)Code channel power –25 dBCode channel power –25 dBExternal triggerMeasurementsOption 020Channel PowerRel power at defined rangeTime offsetPilot, Paging, Sync, Q-PagingFrequency errorChannel powerMulti-ACPRCarrier feed-throughCDP TableTime offsetSpectral densityLowest reference powerPN offsetReference powerCarrier feed-throughPeak to average powerHighest reference powerCode Domain PowerCode utilizationPilot powerOccupied BandwidthAbs power at defined rangeAbs/Rel code powerCode, spreading factorMax inactive powerOccupied bandwidthRel power at defined rangeChannel powerAllocation (channel type)PN offsetIntegrated powerSpurious EmissionsPower bar graph (Abs/Rel)Relative, absolute powerPower Statistics CCDFOccupied powerPeak freq at defined rangePilot, paging, sync, Q-pagingAuto MeasureSpectrum Emission MaskPeak level at defined rangeMax, avg active powerChannel powerReference powerConstellationMax, avg inactive powerOccupied bandwidthPeak level at defined rangePilot powerPN offsetSpectrum emission maskACPRRhoCodogramACPRReference powerEVMCode utilizationMulti-ACPRAbs power at defined rangeFrequency errorRCSIRhoOption 040Channel Scanner (up to 6)Ec/Io, pilot power, delayPN offsetPeak amplifier capacityFrequencies or channelsMultipath ProfilePilot, paging, sync, Q-pagingpowerAverage amplifier capacityChannel power, PN offsetChannel powerMax, avg active powerCode utilizationPilot power, Ec/IoMultipath powerMax, avg inactive powerPeak utilizationPN Scanner (up to 6)Ec/Io, delayFrequency errorAverage utilizationChannel powerCode Domain PowerTime offset, Rho, EVMRoute MapPilot dominanceAbs/Rel code powerCarrier feed-throughPilot powerPN offsetChannel powerAmplifier capacityEc/IoLongitude, latitude, and satellite in all screens5 CellAdvisor JD745B Base Station Analyzer Specifications
EV-DO Signal Analyzer (Options 021 and 041)General ParametersFrequency rangeBand 0 to 10Input signal level–40 to 20 dBmRF channel power accuracy 1.0 dB (typical)EV-DO compatibilityRev 0, Rev A and Rev BFrequency error 10 Hz ref freq accuracy99% confidence levelRho accuracy 0.0050.9 Rho 1.0Residual Rho 0.995 (typical)PN offset1 x 64 chipsCode domain power 0.5 dB relative power 1.5 dB absolute powerPilot power accuracy 1.0 dB (typical)Time offset 1.0 µs, 0.5 µs (typical)Code channel power –25 dBCode channel power –25 dBExternal triggerMeasurementsOption 021Channel PowerAbs power at defined rangePilot, MAC, data EVMChannel powerRel power at defined rangeConstellation (pilot, MAC Slot average power64/128, and data)Data channel powerSpectrum emission maskACPRSpectral densitySpurious EmissionsChannel powerMax, avg active powerMulti-ACPRPeak to average powerPeak frequency at defined rangeRho, EVM, peak CDEMax, avg inactive powerPilot, MAC, data powerOccupied BandwidthPeak level at defined rangeFrequency errorPN offsetOn/off ratioOccupied bandwidthPower vs. Time(idle and active slot)Time offsetMAC CodogramPvsT mask (idle slot) orPvsT mask (active slot)Integrated powerSlot average powerCarrier feed-throughCode utilizationFrequency errorOccupied powerOn/off ratioPN offsetRCSITime offsetSpectrum Emission MaskIdle activityModulation type*Slot, pilot, MAC, dataCarrier feed-throughReference powerPilot, MAC, data powerCode Domain Power(pilot and MAC 4/128)MAC CDP TablePilot, MAC, data RhoPeak level at defined rangeConstellation(composite 64/128)Pilot/MAC channel powerReference powerMax inactive I/Q powerACPRChannel powerSlot average powerCode utilizationPN offsetReference powerRho, EVM, Peak CDEMax active I/Q powerCode, spreading factorPower Statistics CCDFAbs power at defined rangeFrequency errorAvg active I/Q powerAllocation (channel type)Rel power at defined rangeTime offsetMax inactive I/Q powerRelative, absolute powerMulti-ACPRCarrier feed-throughAvg inactive I/Q powerAuto MeasureLowest reference powerPN offsetPN offsetChannel powerHighest reference powerPilot, MAC, data powerCode Domain Power(data)Occupied bandwidthChannel Scanner (up to 6)Pilot dominanceEc/Io, delay(Composite) EVMCode utilizationFrequencies or channelsPN offsetCode Domain PowerFrequency errorPeak utilizationPN offsetEc/Io, pilot power, delaySlot average powerTime offsetAverage utilizationPilot, MAC, data powerMultipath ProfilePN offsetCarrier feed-throughRoute MapPN Scanner (up to 6)Channel powerPilot, MAC,data powerMax active I/Q powerPilot powerChannel powerMultipath powerPilot, MAC, data RhoAvg active I/Q powerEc/IoOption 041Longitude, latitude, and satellite in all screens*Measurement is performed in Data Constellation only.6 CellAdvisor JD745B Base Station Analyzer Specifications
GSM/GPRS/EDGE Signal Analyzer (Options 022 and 042)General ParametersFrequency range450 MHz to 500 MHz820 MHz to 965 MHz1.705 GHz to 1.995 GHzInput signal range–40 to 20 dBmBurst power 1.0 dBFrequency error 10 Hz reference-frequency accuracy99% confidence levelPhase RMS AccuracyResidual errorPhase peak accuracy8 PSK modulation quality 1.0 degrees0.7 degrees (typical) 2.0 degrees(0 Phase RMS 8)EVM AccuracyResidual errorRF power vs. time 1.5%2.5% 0.25 symbol(2% EVM 8%)GMSK modulation quality(0 Phase peak 30)MeasurementsOption 022Channel PowerPeak level at defined rangeTSC (Slot 0 to 7)C/I*PvsT – MaskChannel powerSpurious EmissionsConstellationEVM RMS*Frame average powerSpectral densityPeak frequency at defined rangeBurst powerEVM Peak*Frequency errorPeak to average powerPeak level at defined rangeModulation typeEVM 95th*Phase error RMSOccupied BandwidthPower vs. Time (slot)Frequency errorAuto MeasurePhase error peakOccupied bandwidthBurst powerPhase error RMSChannel powerEVM RMS*Integrated powerMax/min pointPhase error peakOccupied bandwidthEVM Peak*Occupied powerPower vs. Tme (frame)I/Q origin offset*Spectrum emission maskI/Q origin offsetSpectrum Emission MaskFrame average powerTSCSpurious emission maskC/I*Reference powerBurst power (Slot 0 to 7)BSICBurst powerOption 042Channel/Frequency ScannerBSIC (NCC, BCC)SNR, delayFrame average powerChannels or frequenciesMultipath ProfileModulation AnalyzerBSIC, frame no. and timeAbsolute power(10 strongest)Frame avgpower trendC/I, frequency errorGroup (traffic, control)Frame average powerC/I trendBurst powerLongitude, latitude, and satellite in all screens* Measurements performed for 8PSK modulation signals (edge) only.7 CellAdvisor JD745B Base Station Analyzer SpecificationsModulation type
WCDMA/HSPA Signal Analyzer (Options 023 and 043)General ParametersFrequency rangeBand 1 to 14, 19 to 22, 25, 26Input signal range–40 to 20 dBmRF channel power accuracy 1.0 dB, 0.7 dB (typical)Occupied bandwidth accuracy 100 kHzAdjacent channel leakage ratio (ACLR) –56 dB, 0.7 dB at 5 MHz offset, –58 dB, 0.8 dB at 10 MHz offsetWCDMA modulationQPSKHSPA modulationsQPSK, 16 QAM, 64 QAMFrequency error 10 Hz reference-frequency accuracy99% confidence levelEVM accuracy 2.0%2% EVM 20%Residual EVM2.5% (typical)Code domain power 0.5 dB relative power 1.5 dB absolute powerCPICH power accuracy 0.8 dB (typical)Code channel power –25 dBCode channel power –25 dBMeasurementsOption 023Channel PowerAbs power at defined rangeMax, avg active powerAllocation (channel type)Channel powerRel power at defined rangeMax, avg inactive powerEVM, modulation typeSpectral densitySpurious EmissionsScramble codeRelative, absolute powerPeak to average powerPeak frequency at defined rangeRelative Code Domain ErrorAuto MeasureOccupied BandwidthPeak level at defined rangeAbs/Rel code powerChannel powerOccupied bandwidthConstellationCode errorOccupied bandwidthIntegrated powerCPICH powerIndividual code EVM, RCDE, and itsconstellationSpectrum emission maskOccupied powerRho, EVMChannel powerACLRSpectrum Emission MaskPeak CDEPower bar graph (Abs/Rel/Deltapower) CPICH, P-CCPCH, S-CCPCH,PICH,P-SCH, S-SCHMulti-ACLRReference powerFrequency errorAvg RCDE QPSK, 16 QAM, 64 QAMSpurious emission maskPeak level at defined rangeTime offsetCodogramFrequency errorACLRCarrier feed-throughCode utilizationEVMReference powerScramble codeRCSIPeak CDEAbs power at defined rangeCode Domain PowerCPICH, P-CCPCH, S-CCPCH, PICH,P-SCH, S-SCHCarrier feed-throughRel power at defined rangeAbs/Rel code powerCDP TableCPICH absolute powerMulti-ACLRIndividual code EVM and itsconstellationReference powerCPICH relative powerLowest reference powerChannel powerCode utilizationMax inactive powerHighest reference powerPower bar graph (Abs/Rel/Deltapower) CPICH, P-CCPCH, S-CCPCHPICH, P-SCH, S-SCHCode, spreading factorScramble codePower Statistics CCDFOption 043Channel Scanner (up to 6)Multipath ProfileCPICH, P-CCPCH, S-CCPCH, PICH,P-SCH, S-SCHAmplifier capacityFrequencies or channelsChannel, multipath powerMax, avg active powerPeak amplifier capacityChannel power, scramble code,CPICH power, Ec/IoEc/Io, delayMax, avg inactive powerAverage amplifier capacityScramble Scanner (up to 6)Code Domain PowerFrequency errorCode, peak utilizationChannel powerAbs/Rel code powerTime offset, RhoAverage utilizationCPICH dominanceIndividual code EVMCarrier feed-throughRoute MapScramble codeChannel power(Composite) EVMCPICH power, Ec/IoEc/Io, CPICH power, delayScramble codeCPICH EVM, P-CCPCH EVMLongitude, latitude, and satellite in all screen8 CellAdvisor JD745B Base Station Analyzer Specifications
TD-SCDMA Signal Analyzer (Options 025 and 045)General ParametersFrequency range1.785 GHz to 2.22 GHzInput signal level–40 to 25 dBmChannel power (RRC) accuracy 1.0 dB (typical)ModulationsQPSK, 8 PSK, 16 QAM, 64 QAMFrequency error 10 Hz ref freq accuracy99% confidence levelResidual EVM (RMS)2.0% (typical)P-CCPCH slot and 1 channelTime error (Tau) 1.0 µs (typical)External triggerSpreading factorAuto (DL, UL), 1, 2, 4, 8, 16MeasurementsOption 025Channel PowerPower vs. Time (slot)ConstellationCode Power and Error ChartPeak CDEChannel powerSlot powerRhoConstellation diagram forIndividual codeMax inactivepowerSpectral densityDwPTS powerEVM RMS, EVM peakData formatSpurious EmissionPeak to average powerUpPTS powerPeak CDESlot, DwPTS powerOccupied BandwidthOn/off slot ratioFrequency errorNo. of active codeOccupied bandwidthSlot PARI/Q origin offsetScramble codeIntegrated powerDwPTS codeTime offsetMax active code powerOccupied powerPower vs. Time (frame)Midamble PowerAvg active code powerSpectrum Emission MaskSlot Power, Data Power (L),Midamble Power, Data Power(R), Time offset of all TS (fromTS0 to TS7) and DwPTS,UpPTSSlot powerMax inactive code powerReference powerDwPTS powerAvg inactive code powerPeak level at defined rangeMidamble power (1 to 16)Peak CDE and peak active CDEACLRCode PowerAuto MeasureReference powerIndividual code EVM and its Channel powerconstellationAbs power at defined rangeConstellation diagram forIndividual codeOccupied bandwidthRel power at defined range(Modulation) formatSpectrum emission maskMulti-ACLRSlot power, DwPTS powerACLRLowest reference powerNo. of active codeMulti-ACLRHighest reference powerScramble codeSlot powerAbs power at defined rangePower vs. Time (mask)Max active code powerDwPTS powerRel power at defined rangeSlot powerAvg active code powerUpPTS powerSpurious EmissionsOn/off slot ratioMax inactive code powerOn/off slot ratioPeak frequency at defined rangeOff powerAvg inactive code powerFrequency errorPeak level at defined rangeTimogramCode ErrorEVM RMSOption 045Sync-DL ID Scanner (32)Sync-DL ID vs. Tau (up to 6)Ec/Io, TauDwPTS powerScramble code groupID, power, Ec/Io, TauDwPTS powerPilot dominanceEc/Io, TauDwPTS powerPilot dominanceEVM, frequency errorDwPTS powerPilot dominanceSync-DL ID AnalyzerEc/Io, CINRPilot dominanceSync-DL IDMultipathDwPTS power,Ec/Io trendRoute MapLongitude, latitude, and satellite in all screens9 CellAdvisor JD745B Base Station Analyzer SpecificationsDwPTS Power
Mobile WiMAX Signal Analyzer (Options 026 and 046)General ParametersFrequency range2.1 GHz to 2.7 GHz3.4 GHz to 3.85 GHzInput signal level–40 to 20 dBmChannel power accuracy 1.0 dB (typical)Supported bandwidth7 MHz, 8.75 MHz, and 10 MHzFrequency error 10 Hz reference-frequency accuracyResidual EVM (RMS)1.5% (typical)99% confidence levelMeasurementsOption 026Channel PowerPeak level at defined rangeFrequency errorEVM vs. SymbolFrame average powerChannel powerPower vs. Time (frame)Time offsetRCE RMS, RCE peakTime offsetSpectral densityChannel powerSegment ID, cell IDEVM RMS, EVM peakI/Q origin offsetPeak to average powerFrame average powerPreamble indexSegment ID, cell IDSpectral flatnessOccupied BandwidthPreamble powerSpectral FlatnessPreamble indexFrequency errorOccupied bandwidthDL burst powerAverage subcarrier powerAuto MeasureRCE RMSIntegrated powerUL burst powerSubcarrier power variationChannel powerRCE peakOccupied powerI/Q origin offsetMax, min, avg powerOccupied bandwidthEVM RMSSpectrum Emission MaskTime offsetEVM vs. SubcarrierSpectrum emission maskEVM peakReference powerConstellationRCE RMS, RCE peakSpurious emission maskPower Statistics CCDFPeak level at defined rangeChannel powerEVM RMS, EVM peakPreamble powerSpurious EmissionsRCE RMS, RCE peakSegment ID, cell IDDL burst powerPeak frequency at defined rangeEVM RMS, EVM peakPreamble indexUL burst powerOption 046Preamble Scanner (up to 6)Total preamble powerPreamble powerTime offsetTotal preamble powerMultipath powerFrame avg powerRoute MapPreamble, relative powerRelative power, delayRelative powerPreamble powerCell ID, sector IDPreamble power trendC/ITime offsetPreamble Power TrendPreambleMultipath ProfileRelative power trendCell ID, sector IDLongitude, latitude, and satellite in all screens10 CellAdvisor JD745B Base Station Analyzer Specifications
LTE/LTE-Advanced ‒ FDD Signal Analyzer (Options 028/030/032 and 048)General ParametersFrequency rangeBand 1 to 14, 17 to 26Input signal level–40 to 20 dBmChannel power accuracy 1.0 dB (typical)Supported bandwidths1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, and 20 MHzFrequency error 10 Hz reference-frequency accuracy99% confidence levelResidual EVM (RMS)Measurements2.0% (typical)Data EVMChannel PowerChannel powerPower vs. Time (frame)Frame average powerSpectral densityPeak to average powerOccupied BandwidthOccupied bandwidthIntegrated powerOccupied powerSubframe powerFirst slot powerSecond slot powerCell ID, I/Q origin offsetTime offsetConstellationOption 028/030/032Control ChannelData EVM RMS, peakControl channel sumRS EVM RMS, peakmary (P-SS, S-SS, PBCH,PCFICH, PHICH, PDCCH, Cell, group, sector IDRS, MBSFN*)FrameAntenna 1 RS powerand EVMAntenna 2 RS powerand EVM**MBSFN*Antenna 3 RS powerand EVM**EVM, relative or absolute Frame summary tablepower, modulation type (P-SS, S-SS, PBCH, PCData Allocation MapFICH, PHICH, PDCCH, RS, Data allocation vsEach control channels’MBSFN*, PDSCH/Data* frameQPSK, PDSCDH/Data* 16 Resource block powerSpectrum Emission Mask MBSFN*I/Q diagramQAM,PDSCH/Data* 64 OFDM symbol powerRS TX powerModulation formatQAM, PDSCH 256QAM) Data utilizationReference powerPDSCH/Data* QPSK EVM Frequency errorPeak level at definedrangeACLRReference powerAbs power at definedrangeRel power at definedrangeMulti-ACLRLowest reference powerHighest reference powerAbs power at definedrangePDSCH/Data* 16 QAMEVMPDSCH/Data* 64 QAMEVMPDSCH 256QAM EVMData EVM RMSData EVM peakFrequency errorTime errorData ChannelMBSFN*Resource block powerI/Q diagramRB powerRel power at definedModulation formatrangeSpurious EmissionsI/Q origin offsetPeak frequency at defined EVM RMS, EVM peakrangePeak level at definedrangeChannel Scanner (up to 6) ID Scanner (up to 6)Frequency or channelsCell, group, sector IDChannel powerRSRP/RSRQRS-SINRAntenna portRSRP/RSRQ dominanceS-SS RSSI dominanceS-SS Ec/Io dominanceCell, group, sector IDRSRP/RSRQRS-SINR/S-SS RSSIP-SS/S-SS PowerS-SS Ec/IoI/Q origin offsetEVM RMS, EVM peakSubframeMBSFN*Subframe summary table(P-SS, S-SS, PBCH, PCFICH, PHICH, PDCCH, RS,MBSFN*, PDSCH/Data*QPSK, PDSCH/Data* 16QAM, PDSCH/Data* 64QAM, PDSCH 256QAM)EVM, relative or absolute power, modulationtypeData allocation vssubframeResource block powerFrame average powerOFDM symbol powerFrequency errorI/Q origin offsetData utilizationAuto MeasureChannel powerOccupied bandwidthEVM RMS, peakSpectrum emissionmaskACLRMulti-ACLRSpurious emissionmaskFrame average powerData EVM RMS, peakCell, group, sector IDTime Alignment ErrorEVM, relative or absolute Time alignment errorpower, modulation type trendSubframe powerOFDM symbol powerFrequency, time errorTime alignment errorRS power differenceAntenna 0 RS powerand EVMOption 048Multipath ProfileControl channel tableCell, group, sector IDAnt 0 RS Ec/Io, delayAnt 1 RS Ec/Io, delayAnt 2 RS Ec/Io**, delay**Ant 3 RS Ec/Io**, delay**Control ChannelRS power trendCell, group, sector IDLongitude, latitude, and satellite in all screens*Measurement is performed when MBMS is enabled.**Measurement is performed when option 030 is enabled.11 CellAdvisor JD745B Base Station Analyzer Specifications(P-SS, S-SS, PBCH, PCFICH, RS 0, RS 1, RS 2**,RS 3**, MBSFN RS*)Absolute powerRelative powerEVM RMS, phaseFrequency errorTime alignment errorPDSCH/Data* 64QAM EVMPDSCH 256QAM EVMData EVM RMS, peakRS, P-SS, S-SS EVMRS, P-SS, S-SS powerPBCH powerSubframe powerOFDM powerTime errorI/Q origin offsetCarrier Aggregation**Component carriers:up to 5Subframe powerP-SS, S-SS, PBCH, RSpower and EVMPDSCH/Data* QPSKpower and EVMPDSCH/Data* 16 QAMpower and EVMPDSCH/Data* 64QAM power and EVMPDSCH 256QAM EVMCell IDFrequency errorTime alignment errorFrequency errorMBSFN*PDSCH/Data* QPSKEVMPDSCH/Data* 16 QAMEVMAntenna portPower StatisticsCCDFPMCH subframepower*Time alignment errorTime offsetDatagramDatagramResource block powerData utilizationRoute MapRSRPRSRQRS-SINRS-SS RSSIP-SS/S-SS PowerS-SS Ec/Io
LTE/LTE-Advanced ‒ TDD Signal Analyzer (Options 029/031/033 and 049)General ParametersFrequency rangeBand 33 to 43Input signal level–40 to 20 dBmChannel power accuracy 1.0 dB (typical)Supported bandwidth1.4 MHz, 3 MHz, 5 MHz, 10 MHz, 15 MHz, and 20 MHzFrequency error 10 Hz reference-frequency accuracy99% confidence levelResidual EVM (RMS)2.0% (typical)Data EVMMeasurementsChannel PowerChannel powerSpectral densityPeak to average powerOccupied BandwidthSpurious EmissionsPeak frequency atdefined rangeOption 029/031/033Data EVM peakSubframeFrequency errorMBSFN*Antenna 3 RS powerand EVM**PDSCH 256QAM EVMSubframe summary table(P-SS, S-SS, PBCH, PCFICH, PHICH, PDCCH, RS,MBSFN*, PDSCH/Data*QPSK, PDSCH/Data* 16QAM, PDSCH/Data* 64QAM, PDSCH 256QAM)Cell, group, sector IDData Allocation MapData allocation vsframeResource block powerSecond slot powerI/Q origin offsetCell ID, I/Q origin offset EVM RMS, EVM peakSubframe powerResource block powerTime offsetControl ChannelOFDM symbol powerData utilizationACLRReference powerAbs power at definedrangePower vs. Time (slot)Slot average powerTransient period lengthOff powerControl channel summary(P-SS, S-SS, PBCH, PCFICH, PHICH, PDCCH, RS,MBSFN*)Frequency, time errorData EVM RMS, peakRS EVM RMS, peakCell, group, sector IDRel power at definedrangeConstellationMBSFN*Multi-ACLRRS TX powerEVM, relative or absolute Time Alignment Errorpower, modulation type Time alignment errortrendEach control channels’Time alignment errorAuto MeasureChannel powerOccupied bandwidthSpectrum emissionmaskACLRMult-ACLRLowest reference powerPDSCH/Data* QPSKEVMPDSCH/Data* 16 QAMEVMPDSCH/Data* 64 QAMEVMPDSCH 256QAM EVMData EVM RMSOccupied bandwidthIntegrated powerOccupied powerSpectrum EmissionMaskReference powerPeak level at definedrangeHighest reference powerAbs power at definedrangeRel power at definedrangeChannel Scanner(up to 6)Frequency or channelsCell, group, sector IDChannel powerRSRP/RSRQRS-SINRAntenna portPeak level at definedrangePower vs. Time(frame)Frame average powerSubframe powerFirst slot powerID Scanner (up to 6)RSRP/RSRQ dominanceS-SS RSSI dominanceS-SS Ec/Io dominanceCell, group, sector IDRSRP/RSRQRS-SINR/S-SS RSSIP-SS/S-SS powerS-SS Ec/IoPDSCH/Data* 64 QAMEVMTime errorData ChannelMBSFN*Resource block powerI/Q diagramRB powerModulation formatOFDM symbol powerData utilizationEVM, relative or absolute Data allocation vspower, modulation type subframeSpurious emissionmaskSlot average powerData EVM RMS, peakRS, P-SS, S-SS EVMRS, P-SS, S-SS powerPBCH powerSubframe powerOFDM powerTime errorI/Q origin offsetCarrier Aggregation**Component carriers:up to 5Subframe powerP-SS, S-SS, PBCH, RSpower and EVMPDSCH/Data* QPSKpower and EVMPDSCH/Data* 16 QAMpower and EVMI/Q diagramRS power differenceModulation formatFrequency errorAntenna 0 RS power and Off powerEVMTransition periodTime alignment errorPDSCH/Data* 64 QAMpower and EVMPDSCH 256QAM EVMI/Q origin offsetEVM RMS, EVM peakAntenna 1 RS power andEVMAntenna 2 RS power andEVM**MBSFN*PDSCH/Data* QPSKEVMPDSCH/Data* 16 QAMEVMCell IDFrequency errorTime alignment errorAntenna portPower Statistics CCDFEVM RSM, phaseFrequency errorPMCH subframe power*Time alignment errorTime offsetDatagramDatagramResource block powerData utilizationRoute MapRSRPRSRQRS-SINRS-SS RSSIP-SS, S-SS powerS-SS Ec/IoOption 049Multipath ProfileControl ChannelCell, group, sector IDRS po
Video Bandwidth (VBW) -3 dB bandwidth 1 Hz to 3 MHz 1-3-10 sequence Accuracy 10% (nominal) Single Sideband (SSB) Phase Noise . Accuracy Same as spectrum analyzer External RF Power Sensors Directional JD731B JD733A Frequency range 300 MHz to 3.8 GHz 150 MHz to 3.5 GHz Dynamic range 0.15 to 150 W (av - erage)
