Transcription
DOOR CLOSERS
DOOR CLOSERPhiladelphia Hardware Group, Inc. is presenting the finest ADVANTAGE surface mounting door closerscertified by BHMA including: Multi-size door closer: 9000, 8000, 6000, 6000S (slim cover), 5000, 4400 series. Standard size door closer: 4000, 3000, 2000 series. Multi-size Delay Action door closer: 8000/DA, 6000/DA, 6000S/DA series.GENERAL INFORMATIONANSI A156.4 – American National Standard for Door Controls-ClosersADVANTAGE Grade 1 Door Closers are certified by ANSI/BHMA A156.4.ADVANTAGE Grade 2 Door Closers are factory tested to meet or exceed ANSI Grade 2 required strength and performance.UL ListedAll of ADVANTAGE door closer series are UL listed, and conforms to Standards UL10C and UPC 7-2(1997).Meet ADA requirementsADVANTAGE door closer 9000, 8000, 6000, and 4400 series meet ANSI A117.1 requirements for ADA.Please note Door Closer with reduced opening force may not provide sufficient power to close a door. Doorways shall have a clear opening of 32” minimum. Clear opening of doorways with swinging doors shall be measured fromthe face of door and stop with the door open 90 . Door closers shall be adjusted so that from the open position of 90 the time required to move the door to an open position of12 shall be 5 seconds minimum. The maximum force for pushing open or pulling open doors other than fire doors shall be as follows:1. Interior hinged door: 5 lbs.2. Exterior hinged door: 8.5 lbs.* 4400 series apply to interior hinged door only.HandingAll ADVANTAGE Door closers are non-handed that are suitable for left-opening or right-opening door.All Weather Hydraulic Fluid used to ensure smooth operation under severe weather conditions.Finish Stock available Aluminum (BHMA 689) for all modelDuranodic (BHMA 695) for all modelGold (BHMA 696) for all modelSatin Chrome (BHMA 652) for 8000 seriesAluminumDuro (Duranodic)GoldACCESSORIESDrop Plate allows a door closer to be fitted on narrow top rail or narrow top frame door.Most of the ADVANTAGE door closers have different kinds of Drop Plates for installation requirements, see following pages in detail.Hold Open Arm used when door is requiring for a clear opening doorways at 90 stop.* Should not be used on Fire door application.Parallel Rigid Cush Arm is a heavy duty arm with an auxiliary stop in soffit shoe to stop the door opening at a specificpoint. Apply to door where wall or floor stops are not appropriate. Parallel arm mounting application only.Parallel Rigid Spring Cush Arm is Parallel Rigid Cush Arm with a Spring Stop in soffit shoe for abusive application.Parallel Rigid Hold Open Cush Arm is a heavy duty hold open arm featured with a plunger hold open to engage ordisengage hold open by a handle on the arm. Auxiliary stop in soffit shoe to stop the door opening at a specific point.Parallel arm mounting application only.* Should not be used on Fire door application.Parallel Rigid Hold Open Spring Cush Arm is Parallel Rigid Hold Open Cush Arm with a Spring Stop in soffit shoefor abusive application.* Should not be used on Fire door application.Parallel Rigid Arm is an extra heavy duty arm that is intended to use in heavy traffic areas. Parallel arm mounting application only.1
DOOR CLOSERACCESSORIESArm Support BracketBlade Stop Spacer lowers parallel arm shoe to clear 1/2” (13mm) blade stop.Arm Support Bracket provides anchor for fifth screw, to use with stop arms whenreveal is less than 3-1/16” (78mm). (for 8000 door closer only)Blade Stop SpacerDOOR CLOSER APPLICATIONThere are three basic methods of mounting surface door closers to the door and frame including regular arm, parallel arm and topjamb mounts. All ADVANTAGE door closers are supplied standard with a tri-pack for mounting any of three types applications.Parallel Arm InstallationRegular ArmInstallationcloser mountson hinge(pull) side of doorLeft hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRRegular Arm (Pull side)Most power-efficient applicationThe Closer body is mounted on thehinge side of the door top rail.The forearm is mounted to the frameface by a mounting shoe.Arm projects at approximately a 90 angle away from the door.Top JambInstallationcloser mountson frame face onopposite to hinge(pull) side of doorcloser mounts onopposite to hinge (pull) side of doorLeft hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRTop Jamb (Push side)More power-efficient than theparallel arm applicationApplying to a closer with narrow toprail on a door.The closer body is mounted to theframe face above the door, oppositethe door hinge side.The forearm is then mounted to thetop rail of the door.Left hand door-LHRight hand reverse-RHRRight hand door-RHLeft hand reverse-LHRUse adjustable wrench to rotate spindle 45 counter-clockwise for right hand door or clockwisefor left hand door. Place main arm on spindle sothat the “R” (Right hand door) or “L” (Left hand door)lines up with the spindle flat. Secure main arm andspindle by tightening spindle bolt.Parallel Arm (Push side)Least power-efficient applicationThe closer body is mounted on the toprail of the door, opposite the hinge sideof the door.The forearm is mounted by aparallel arm bracket to the undersideof the frame.The arm is parallel to the door, whichmakes it less likely to be damaged.* Top reveal should have enough spacefor using this application.CLOSER ADJUSTMENTADVANTAGE Door closers have hex wrench controlling valves for adjusting Closing speed and latch speed. Multi-size door closers have a nut for spring poweradjustment, and additional valve for Backcheck. Delay Action control valve availablewith Delay Action model.Opening Cycle2
DOOR CLOSERClosing speed &Latching speed aredual valve control for doorclosing speed.Closing speed is the speed ofdoor closing from full openingto approximately 10 5 of doorclosed position.Latching speed is the speedfrom approximately 10 5 dooropening to door closed position. Slow latch speed providesless door closing noise.Backcheck slows down thedoor opening at approximately70 in order to prevent damageto building and door frames.The backcheck control valveprovides a 20 adjustment (70 90 ) to set the optimum backcheck start point.* Multi-size door closers arestandard with Backcheckfunction.Delay Action is the 3rdcontrol for closing speed adjustment.It effective from full openingto approximately 70 , andprovides a slow closing speed.The closing time between 180 to 70 is at least 20seconds,and easily adjustable up to1minutes. Closer with DelayAction provides sufficienttime that allows people or theelderly to get through the doorbefore it starts to close.Multi-size Spring adjustmentMulti-size door closers are able to adjust the spring power to meet the power needs of the door.Spring power of the closer can be increased by turning the power adjustment nut clockwise, vice versa.Closer Size (Spring Power)CloserRecomme n d e d Ma x i m u m Do o r S i z eRegular & Top JambParallel ArmInteriorExterior Swing-in(Pull Side)Exterior Swing-out(Push SideInterior Swing-out(Push side)Exterior Swing-out(Push side)128”N/AN/AN/AN/A236”N/AN/A30”N/A66 99342”30”36”36”30”99 143448”36”42”42”36”143 187554”42”48”48”42”187 264660”48”54”54”48”264 330* Multi-size door closers provide the spring power required to fit your door size and application.3Door WeightSize(Lbs.)33 66
9000 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel9000ULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckApplications Heavy Duty Commercial model ideal for high traffic doorsuch as schools, hospitals, and public institutions Same mounting hole pattern as CAL-ROYAL 900(CTC 11-1/8” x 1-1/8”), ideal for renovations Tri-packed for all type applications Sex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 1-6Factory preset size 3 Meet ADA Standard with adjustable BackcheckProduct SpecificationMaterialCoverValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, andBack-checkStaked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and GoldOptional Fuctions Hold Open Arm (9001)Parallel Rigid Cush Arm (9002)Parallel Rigid Cush and Stop Arm (9003)Extended forearm (9004)Parallel Rigid Arm (9005)Drop Plate (90DP-PA)* Special order from the factory Delay Action Metal cover Plated Finish: US3, US26, US26DTechnical DimensionsSeries 9000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from DoorSize11-7/8”11-1/8”1-1/8”2”2-3/8”End ViewFront ViewAccessories9001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount9002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open ArmPAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stop9003Parallel RigidHold Open Cush ArmHand control plunger hold openAuxiliary stop in soffit shoe9005Parallel Rigid ArmFeatured with solid steelmain & forearm for extraheavy traffic use90DP-PASize: 11-13/16” x 3-9/16”Drop Plate –Parallel arm mountUsed to mount a closer on a top rail as narrowas 1-9/16” in height9004Extended ForearmFor Top Jamb with revealgreater than 4” and upto 8”90CStandard FullPlastic Cover1348Sex-bolt with screwFor 1-3/4” standard Door Thick4
8000 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel80008000/DAULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckAdjustable power size 1-6 with Delay ActionApplications Extra Heavy Duty Commercial model ideal for high traffic door Versatile for new constructions, such as schools, hospitals,and public institutionsSame mounting hole pattern as LCN4041, ideal for renovationsTri-packed for all type applicationsSex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 1-6Factory preset size 3 Meet ADAProduct SpecificationOptional FuctionsCoverValves MaterialArm &BracketsScrewsFinishesHeavy Duty Cast Iron body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed,and Back-check cushionDelayed Action valve – Optional (Model: 8000DA)Staked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, Gold, and US26D-Satin ChromeWide choice of options for different applicationsHold Open Arm (8001)Parallel Rigid Cush Arm (8002)Parallel Rigid Cush and Stop Arm (8003)Extended forearm (8004)Parallel Rigid Arm (8005)Drop Plate (see Accessories)* Special order from the factory Metal cover Plated Finish: US3, US26AccessoriesTechnical DimensionsSizeSeries 800011”A. Length of Closer Body5”B. Horizontal Mounting Holes1”C. Vertical Mounting Holes2-3/4”D. Height of Closer Body2”E. Projection from Door8001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount8002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open Arm8004Extended ForearmFor Top Jamb withreveal between2-5/8” to 4-13/16”5Front ViewEnd View80058003Parallel Rigid ArmParallel RigidFeatured with solid steelHold Open Cush ArmHand control plunger hold open main & forearm for extraAuxiliary stop in soffit shoe heavy traffic use8003SCParallel Rigid Hold Open Spring Cush ArmHand control plunger hold open. Spring stop in soffit shoePAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallelarm applicationASB01Arm Support BracketUse with Cush Arms whenreveal is less than 3-1/16” (78 mm). Thebracket provides anchorage for fifth screw loadingBSS01Blade Stop SpacerDesign to lower parallelarm shoe to clear 1/2”(13 mm) blade stop80DP-STSize: 12-1/4 x 3-9/16”Drop Plate – Pull SideHinge side mount when top rail is less than 3-3/4”Plate require 2” minimum top rail80DP-TJSize: 12-1/4 x 3-9/16”Drop Plate – Top JambUse when frame face is less than 3 1/2”Use 8004 forearm if top reveal exceeds 2-9/16”80DP-TGSize: 12-1/4 x 3-9/16”Drop Plate – Top Jambwith flush ceilingTop of head frame face in flush ceiling conditionPlate requires 1-3/4” minimum frame faceUse 8004 forearm if top reveal exceeds 2-9/16”80DP-PASize: 12-1/4 x 5”Drop Plate – Parallel ArmUse when top rail is less than5-1/2”, measured from the stopPlate requires at least 2-1/2” top rail80CStandard FullPlastic Cover1348Sex-bolt with screw
6000, 6000S SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel6000, 6000S6000/DA, 6000S/DAULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)Comply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 1-6 with Back CheckAdjustable power size 1-6 with Back Check and Delay ActionFull CoverApplications Heavy Duty Commercial model ideal for high traffic door Versatile for new constructions, such as schools,hospitals, and public institutionsSame mounting hole pattern as NORTON 8000 CTC 12” x 3/4”,ideal for renovationsTri-packed for all type applicationsSex-bolts included for Metal Door mountingSlim CoverFeatures Multi-size spring adjustable power size 1-6,Factory preset size 3 Meet ADA Standard with adjustable BackcheckProduct SpecificationMaterialCoverValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – 6000 seriesTriple valve control for Closing speed, Latching speed, andBack-checkDelayed Action valve – Optional (Model: 6000/DA, 6000S/DA)Staked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and GoldOptional FuctionsWide choice of options for different applications Hold Open Arm (6001) Parallel Rigid Cush Arm (6002) Parallel Rigid Cush and Stop Arm (6003) Extended forearm (6004) Drop Plate (see Accessories)* Special order from the factory Metal cover (Full Cover only) Plated Finish: US3, US26, US26DTechnical DimensionsSizeSeries 6000, 6000S12-3/4”A. Length of Closer BodyB. Horizontal Mounting Holes 12”3/4”C. Vertical Mounting Holes1-1/4”D. Height of Closer Body2-1/8” End ViewE. Projection from Door6001Hold-open ArmStand for pull side & top jambUse with PA bracket forparallel arm mount6002Parallel RigidCush ArmAuxiliary Stop insoffit shoeHFW01 Flat Wrench for Hold Open ArmPAB01Parallel BracketFor Hold Open Arm mountingcan also use for regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stop6003Parallel RigidHold Open Cush ArmHand control plunger hold openAuxiliary stop in soffit shoeFront View6004Extended ForearmFor Top Jamb with revealgreater than 4” and upto 8”60C-FStandard Full Plastic Cover60C-SStandard Slim Plastic CoverAccessories60DP-STSize: 13-1/8 x 3-1/4”Drop Plate – Pull Side , orConcealed Door HolderUse for hinge side mountUpside-down to mount where concealed doorholder prevents normal door closer mountingPlate require 2-7/16” minimum top rail60DP-TJSize: 13-1/8 x 3-5/8”Drop Plate – Top JambApply to low ceiling clearance between1-1/2” 1-3/4”60DP-PASSize: 13-1/8 x 3-5/8”Drop Plate – Parallel ArmPlate require 2-7/8” minimum top railCross reference: NORTON #314860DP-PASize: 13-1/8 x 5”Drop Plate –Parallel arm mountUsed to mount a closer on a top rail asnarrow as 3” in height1348Sex-bolt with screw6
5000, 4400 SERIESANSI GRADE 1ANSI/BHMA A156.4Series 2000, PT1Exceeds 1,500,000 cycles with BackcheckModel50004400ULRLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)4400 SeriesComply withANSI A117.1ANSI GRADE 125-Year WarrantyAdjustable power size 3-6 with Back CheckAdjustable power size 1-4 with Back CheckApplications Heavy Duty Commercial model, ideal for high traffic door Versatile for new constructions, such as schools, hospitals,and public institutionsUniversal mounting hole patternSize 4: CTC 9-1/16” x 3/4”Tri-packed for all type applicationsSex-bolts included for Metal Door mountingFeatures Multi-size spring adjustable power size 3-6, factory preset size 4Multi-size spring adjustable power size 1-4, factory preset size 3 4400 meets ADA, Barrier Free interior Standard with adjustable BackcheckProduct SpecificationMaterialCoverValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionFull plastic cover – standardTriple valve control for Closing speed, Latching speed, andBack-checkStaked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandSelf-tapping wood screws, machine screws, and sex-boltsAluminum, Duronotic, and GoldOptional Fuctions Hold Open Arm (4001) Drop Plate (see Accessories)Technical DimensionsSeries 5000, 4400A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from DoorSize9-3/4” 9-3/4”9-1/16” 9-1/16”3/4”3/4”1-3/4” 1-3/4”2-7/8” 2-7/8” End ViewAccessories74001Hold-open ArmStand for pull sideand top jambUse with PA bracket for parallel arm mount40CStandard FullPlastic CoverHFW01Flat WrenchFor Hold Open Arm1348Sex-bolt with screwFor 1-3/4” standard Door ThickPAB02Parallel Bracketfor Hold Open Arm mounting can also usefor regular parallel arm applicationBSS02Blade Stop SpacerDesign to lower parallel armshoe to clear 1/2” (13 mm) blade stopFront View40DP-TJSize: 9-3/4” x 2-9/16”Drop Plate –Top Jamblow ceiling clearanceFor use when ceiling clearance is between1-3/4” and 2-5/8”Cross reference: NORTON #168740DP-PASize: 9-3/4” x 3-1/2”Drop Plate –Parallelarm mountUsed to mount a closer on a top rail as narrow as 2-5/8” in height
4000, 3000, 2000 SERIESGRADE 2ULFactory tested to meetANSI Grade 2 durabilityModel400030002000RLISTEDUL10C Positive PressureRated. Conforms to UBC7-2 (1997). (UniformBuilding Code Standard)ANSI GRADE 210-Year WarrantyStandard power size 4Standard power size 3Standard power size 2Applications Medium and Light Duty model Medium Duty 4000Light Duty3000, 2000Universal mounting hole patternSize 4: CTC 9-1/16” x 3/4”Size 3: CTC 8-3/16” x 3/4”Size 2: CTC 6-5/8” x 3/4”Product SpecificationMaterialValvesArm &BracketsScrewsFinishesAluminum alloy body, forged steel armHeat treated forged steel pistonDouble Heat treated Steel pinionTriple valve control for Closing speed, Latching speed,and Back-checkStaked valve for power adjustmentStandard arm and parallel bracket included for differentmounting demandWood screws and machine screwsAluminum, Duronotic, and GoldTechnical DimensionsSeries 4000, 3000, 2000A. Length of Closer BodyB. Horizontal Mounting HolesC. Vertical Mounting HolesD. Height of Closer BodyE. Projection from /16”6-5/8”3/4”1-3/4”2-5/8”Optional Fuctions End View4001Hold-open ArmFor 4000 SeriesPull side and top jambUse with PA bracket for parallel arm mount3001Hold-open ArmFor 3000 SeriesPull side and top jambUse with PA bracket for parallel arm mountHFW01Flat WrenchFor Hold Open Arm40CFor 4000 SeriesStandard FullPlastic CoverPAB02Parallel Bracketfor Hold Open Arm mounting can also usefor regular parallel arm application1348Sex-bolt with screwFor 1-3/4” standard Door ThickHold Open Arm (3001, 4001)Drop Plate (See Accessories)Sex-bolts (Metal door mounting)Full plastic cover, available for 4000 seriesonly (40C)Front View40DP-TJ For 4000 SeriesSize: 9-3/4” x 2-9/16”Drop Plate –Top Jamblow ceiling clearanceFor use When ceiling clearance is between1-3/4” and 2-5/8”40DP-PA For 4000 SeriesSize: 9-3/4” x 3-1/2”Drop Plate –Parallelarm mountUsed to mount a closer on a top rail asnarrow as 2-5/8” in height30DP-PA For 3000 SeriesSize: 3-1/2” x 8-3/4”Drop Plate – Parallel arm mount20DP-PA For 2000 SeriesSize: 3-1/2” x 7-5/16”Drop Plate – Parallel arm mount8
ORDER INFORMATIONProduct AvailabilitiesSeries Power SizeDuty9000Adjustable No. 1-6Heavy8000Adjustable No. 1-6Extra Heavy8000/DAAdjustable No. 1-6Extra Heavy6000Adjustable No. 1-6Heavy6000SAdjustable No. 1-6Heavy6000/DAAdjustable No. 1-6Heavy6000S/DA Adjustable No. 1-6Heavy5000Adjustable No. 3-6Heavy4400Adjustable No. 1-4Heavy4000No. 4Medium3000No. 3Light2000No. 2LightFunction AvailabilityBack Delay Hold Open with Parallel RigidCheck Action Hold Open Arm Cush ArmCush &Stop ArmAccessoriesParallelRigid ArmDropPlateSex- Plastic MetalBolt Cover Coverl Standard or optionall Special order from the factory, allow for longer lead time. Please call for more informationADVANTAGE Door Closers Power SizeAdjustable Power with Back-Check (BC)AluminumDuroGold9000No. 1-6 BC6099106099116099128000No. 1-6 BC6088106088116088126000No. 1-6 BC6067106067116067126000S (Slim Cover)No. 1-6 BC6067306067316067325000No. 3-6 BC6051106051116051124400No. 1-4 BC6044106044116044126000/DANo. 1-6 BC DA6067406067416067426000S/DA (Slim Cover)No. 1-6 BC DA6067506067516067528000/DANo. 1-6 DA6088406088416088424000No. 46040106040116040123000No. 36033006033016033022000No. 2602200602201602202Adjustable Power with Back-Check (BC) and Delay Action (DA)Adjustable Power with Delay Action (DA)Fixed Power Size9Product Code
CROSS REFERENCEADVANTAGE 90008000Spring Power Size1–61–6CTC Hole Pattern 11-1/8” x 1-1/8” 5” x 2-1/4” x –63 – 6/1 – 443212” x ¾”12” x ¾”9-1/16” x ¾”9-1/16” x ¾”8-3/16” x ¾”6-5/8” x ¾”936N/DC214DC204l DC203300740730l 720440-FP430-Pl 420-P4604l 4603l 46025016NN900-PBFCORBIN/l DC6200RUSSWINl DC3200CRL6000PR74BCDESIGNCR441l DC8000CR801CR801Sl DC6200l DC3200PR90l PR80/PR82BFDC54DC53l DC52PR80 Size 2-5Size 4Size 3Size 2100416316116100100l 89168616l 7400l 7304l 7303l 7204l 7203l SC60/SC61SC64l SC93SC60 Size 2-5SC94HARDWAREDORMAFALCONl SC70SC81SC80DOR-O-MATICGENERAL LOCKC900C7500C7300l C5025/C5014C5025 Size 2-5GLOBALl TC600TC4300TC500TC400TC200TC204TC2203DOOR CONTROLl TC2202HAGERINTERNATIONALl TC302l 90005100520053005400l 5400l 540044CI50008050854853l 852l 754753l 752654653l 652534533l 532l 604l 603602l 5103l 5102DOOR CLOSERLCN4040l 1260Size 1-5NORTONPDQl 1600ManufacturingSARGENTl 1431l 281STANLEYD3550/D3551D4550/D4551S.PARKER900BCl D1650/D1651D1650 Size 2-5l BF900814BCTAYMOR1900l 800/800BF800 Size 2-5TELLYALEl 70090044008003501YMDC2501330160050050l 5104YMDC1101l The same mounting hole pattern with similar application l Different mounting hole pattern in the same power sizeAll brand names & trademarks used are properties of their respective owners10
DISTRIBUTION BY:Philadelphia Hardware Group, Inc.SAN DIEGO DISTRIBUTION CENTER(Home Office)6590 Top Gun StreetSan Diego, CA 92121Tel: (858) 642-0450Fax: (858) 642-0454Toll Free Tel: 1-800-545-2309Toll Free Fax: 1-800-828-0988www.philihardware.comCHICAGO DISTRIBUTION CENTER3687 Darlene CourtAurora, IL 60504Tel: (630) 692-0316Fax: (630) 692-0320Toll Free Tel: 1-800-406-5138Copyright 2013 Philadelphia Hardware Group, Inc. All rights reserved.ATLANTA DISTRIBUTION CENTER2319 Defoor Hills Road N.W.Atlanta, GA 30318Tel: (404) 603-9030Fax: (404) 603-9222Toll Free Tel: 1-855-558-8890
All of ADVANTAGE door closer series are UL listed, and conforms to Standards UL10C and UPC 7-2(1997). Meet ADA requirements ADVANTAGE door closer 9000, 8000, 6000, and 4400 series meet ANSI A117.1 requirements for ADA. Please note Door Closer with reduced opening force may not provide sufficient power to close a door.
