Transcription
DOORstanley door closers d-4550/d-4551D-4550 / D-4551 SERIESC LO S E R S1
General InForMatIonPageGeneral Information. 2–4How To Order .4Standard (Pull) Application .5Parallel Arm (Push) Application .6Top Jamb (Push) Application .7tABLE oF contEntSIntroductIonThe model D4550 Series is Stanley’s best performing Heavy DutyCloser. The cylinder body is manufactured using R-14 SiliconAluminum Alloy providing superior strength and durability oninstitutional applications. Available in a variety of standard andheavy-duty arm configurations accommodating a broader range oftoday’s growing architectural application requirements.FeaturesFully Hydraulic Checking Controls the door through the entireopening and closing cycles by providing adjustable backcheck uponopening and adjusting general and latch speeds through the closingcycle.PageHeavy Duty Arm (Push) Application .8Track Rail Arm (Pull) Application.9Electronic Hold Open (Push) Applications .10Electronic Hold Open (Pull) Applications .11Accessories .12-15All Season FluidAll season fluid eliminates the need for seasonal adjustmentclosing Power Adjustmentd-4550* – Size 2 – 6 with 50% spring power adjustment over size 6.* Meets ADA 5lb opening force requirements on all applications exceptPull-Side Regular Arm Mount.The D-4550 Series is adjusted to size 3 before leaving the factory.d-4551** – Size 1 – 5 with 35% spring power adjustment over size 5.** Meets ADA 5lb opening force requirements.The D-4551 Series is adjusted to size 2 before leaving the factory.delayed ActionA delayed action feature is available with this series for allapplications and arms. The feature permits the door to close veryslowly through the delayed action cycle range.Forged ArmsHeavy duty forged arms are interchangeable between the D-4550and D-3550 Series Door Closers.High Impact coverAll D-4550 / D-4551 Series Door Closers are shipped with a highimpact self-extinguishing decorative cover.(1) opening swing, no checking(2) backcheck (3) general speed (4) latch speed (5) advancedvariable backcheckdelayed Action – optionalThe D-4550DA / D-4551DA Series Door Closers are equipped with aseparate hydraulic valve adjustment to delay the closing speed from180 to 70 degrees of door opening range. To order add suffix DA tocloser number.Latching Power AdjustmentThe D-4550 / D-4551 Series Door Closers have the provision toadjust the leverage of the arms by changing the pivot position ofthe arm in the shoe. The shoe itself does not have to be removedfrom the door or jamb.Maintenance FreeDoor Closers mounted in accordance with the provided installationinstructions are maintenance free from periodic inspection andadjustment.Metal cover - optionalOptional stainless steel, brushed finish metal cover is availablenon-HandedCan be used on both RH and LH doors for both push side and pullside mounting.DADelay RangeSweepAngleAdjustable Spring PowerThe D-4550/D-4551 Series Door Closers are designed to have thewidest range of spring power adjustment available to meet thebroadest range of application requirements.Advanced Variable Backcheck (AVB) optionalCylinder starts backcheck at approximately 45º instead of the normal75º. Add suffix “AVB” to selected cylinder. When combined withDelayed Action consult factory for special template. (Heavy DutyArm applications).2Special High Silicon Aluminum Alloy HousingAll D-4550 / D-4551 Series Door Closers are constructed of“STANLEY’S” R14 HIGH SILICON ALUMINUM ALLOY to exceed theANSI/BHMA A156.4 Grade 1 requirements.Special rust Inhibitor (SrI) - optionalFor installations where a higher level of corrosive resistance isrequired.HandingPULL SIDEPULL SIDEPUSH SIDEPUSH SIDERIGHT HAND DOORLEFT HAND DOORD–4550SERIES
Non-handed feature is available in a variety of finishes wide range of spring power adjustment. Standard packaging with tri-pack: regular,top-jamb and parallel arm arrangement. Can be ordered with heavy duty arm assembly. ANSI/BHMA A156.4 Grade 1, U.L. listed U.S. &Canada. The cylinder body is made from R-14 die cast aluminum. This alloy provides wear resistance from contact with the piston during theopening and closing cycle. R-14 wear characteristics are similar to that of cast iron. In addition the R-14 aluminum alloy holds the cylinderbody dimensionally stable under extreme internal hydraulic pressures.“r-14 high silicon aluminum alloy construction” –Remains dimensionally stable under extremeinternal hydraulic pressure. Provides maximumwear resistance from opening and closing cycle.Backcheckdelayedaction(optional)General InForMatIonGEnErAL InForMAtIonGeneralspeednon-critical regulationThe separate adjustmentsfor backcheck, general andlatch speeds are equipped withnon-critical “V-Slot” regulatingvalves which allow for finetuning the closing and latchingspeeds as well as the backcheck intensity.Latchspeedcut-away d-4550cylinder bodynon-handednon-handedPiston body – cold forged heavy steelconstruction (1 1/2” dia.)Internal springs –Wide range spring power adjustment.Size 2 – 6 with 50% spring power adjustment over size 6.Meets AdA 5lb opening force requirements on all applicationexcept pull-side regular arm mount.DOORC LO S E R SPinion shaft – cold forgedconstruction (5/8” 13 teeth)3
General InForMatIonGEnErAL InForMAtIonArm ageLong Rod Forearm (Top Jams only)Standard Hold OpenParallel Hold OpenElectronic Hold OpenHeavy Duty Arm w/Hold OpenHeavy Duty Arm w/StopHeavy Duty Arm w/Compression StopHeavy Duty Arm w/Hold Open and StopHeavy Duty Arm w/Hold Open & Comp. StopTrack MountTrack Mount w/Hold OpenTrack Compression Stop105613, 1488888101010Packaging Information:All D-4550 / D-4551 Series Door Closers with standard arm sets are packed for mounting on standard, parallel arm or top jamb applications.All closer assemblies are packed 4 per carton. Tracks for track mounted closers are packed separately.through Bolts and Sex nuts:When through bolting is ordered, factory will furnish sex nuts for use with the machine screws furnished with the closer. Nuts are sized toaccommodate 1-3/8” or 1-3/4” thick doors. Mounting screw thread size 12/24.Finishes:689– Aluminum painted690– Dark bronze painted691– Light bronze paintedAnSI and u.L. Specifications:693– Black painted695– Dark bronze painted696– Satin brass paintedThe D-4550/D-4551 Series Door Closers have been Certified to the requirements of the ANSI/BHMA Standard A156.4 - 2000 Grade 1.Available in a variety of ANSI/BHMA finishes. The Stanley Door Closer electro-static finishes surpassed over 100 hours of salt sprayexposure.UL listed with Underwriters’ Laboratories, Inc. and Underwriters’ Laboratories of Canada for “Self Closing Doors WithoutHold-Open Feature”. (File number 7525R).HoW to orderuL10c – uBc 7.2D-4550/D-4550 closers have been tested and certified to meet the positive pressure criterion of UL10C & UBC 7.2 (1997)4HoW to ordEr: d-4550/d-4551d-4550dAEdA689SnModel. no.SizeoptionsArm typeFinishesFastenersL– Long Rod Forearm (TJ only)H – Standard Hold OpenPH – Parallel Hold OpenEdA – Heavy Duty ArmEH – Electronic Hold OpenH-EdA – Heavy Duty Arm w/Hold OpenS – Heavy Duty Arm w/ StopcS – Heavy Duty Arm w/CompressionStopHS – Heavy Duty Arm w/ Hold Open &StopHcS – Heavy Duty Arm w/ Hold Open &Compression StopStd. Packaging – See packaging abovet – Track MountHt – Track Mount w/ Hold OpentcS – Track Compression Stop689690691693695696d-4550– See ClosingAVB – advancedPower Adjustment variable backcheckpage 2(optional)1– See ClosingdA – Delayed ActionPower(optional)Mc – Metal CoverAdjustment(optional)page 2D–4550Sn – Sex Nuts &Bolts Wood &Machine Screwsfurnished standardSEc – SecurityScrewsSERIES
d-4550 / d-4551 Series door closerSpecifications Can be templated for either 120 or 180 (when butt, frame andwall conditions permit.) Custom installation template may be available for unusualinstallation conditions. Contact Stanley for assistance.Hold-open points up to maximum door opening with hold open arm.d-4550/d-4551 Standard ApplicationStandard Installationstandard aPPlIcatIonStAndArd (PuLL) APPLIcAtIonStandard Maximumdoor opening120 opening180 openingA 11-1/4”(286mm)A 9-1/4”(235mm)B 6-1/2”(165mm)B 4-1/2”(114mm)drop Plate Installation P45-180 (For drop plate dimensions see page 7/8”22mm3-13/16”97mm2-1/2”64mmDOORStandard Maximumdoor 120 opening180 openingA 11-5/8”(295mm)A 9-5/8”(238mm)B 8-1/2”(216mm)B 6-1/2”(165mm)1/4”6mmC LO S E R S5
Parallel arM aPPlIcatIonPArALLEL ArM (PuSH) APPLIcAtIond-4550 / d-4551 Series door closerSpecifications Can be templated for either 120 or 180 (when butt, frame andwall conditions permit.) Custom installation template may be available for unusualinstallation conditions. Contact Stanley for assistance.Hold-open points up to maximum door opening with hold open arm.d-4550/d4551 Parallel Arm ApplicationStandard InstallationStandard Maximumdoor opening120 opening180 openingA 8-23/32”(222mm)A 6-3/32”(155mm)B 8-27/32”(224mm)B 6-7/32”(158mm)drop Plate Installation P45-180 (For drop plate dimensions see page 13.)3”76mmdrop PlateMaximum door opening120 opening180 openingA 11-5/8”(295mm)A 9-3/8”(238mm)B 5-15/16”(150mm)B 8”22mm1/4”6mmD–4550SERIES
d-4550 / d-4551 Series door closerSpecifications Can be templated for either 120 or 180 (when butt, frame andwall conditions permit.) Standard reveals up to 3” (76 mm) For deeper reveals use long rod and shoe A45-501L (See page 9) Custom installation template may be available for unusualinstallation conditions. Contact Stanley for assistance.d-4550/d4551 top Jamb ApplicationtoP JaMB aPPlIcatIontoP JAMB (PuSH) APPLIcAtIonStandard InstallationdoorStandard Maximumdoor openingFrame11-29/32”302mm2-7/16”62mmA180 openingA 6-13/32”(163mm)A 4-13/32”(112mm)B 11-9/32”(286mm)B 2mm3-13/16”97mm13-1/32”331mm120 openingB2-15/32”63mmdoordrop Plate Installation P45-180 (For drop plate dimensions see page p PlateMaximum door opening120 opening180 openingA 8-3/8”(213mm)A 6-3/8”(162mm)B 11-5/8”(295mm)B 9-5/8”(244mm)1-3/4”44mmC LO S E R S7
d-4550 / d-4551 Series door closerSpecifications EDA, H-EDA, S, CS, HS and HCS Can be templated for either 120 or 180 (when butt, frame andwall conditions permit.) Custom installation template may be available for unusualinstallation conditions. Contact Stanley for assistance.Hold-open is approximately 3º less than maximum door opening.Heavy duty Push Installationd-4550/d-4551 Heavy duty Arm Application4”102mmAStandard Maximumdoor opening5-19/32”142mmHeaVy dUty arM aPPlIcatIonHEAVY dutY ArM (PuSH) APPLIcAtIonFrame13-9/16”344mm120 opening160 opening180 openingA 7-3/8”(187mm)A 6-3/32”(155mm)A 4-5/8”(117mm)B 6-1/2”(165mm)B 5-11/32”(136mm)B oor2-7/16”62mm13-1/32”331mmdrop Plate Installation P45-180-D (For drop plate dimensions see page 13.)3-3/8” 86mm2-1/8” 55mm5/16” 8mm11/16” 25mmdrop PlateMaximum door opening2-3/8”60mm3-3/16”81mm5 15/32”139mmFrameA120 opening160 opening180 openingA 9-3/8”(238mm)A 8-1/4”(210mm)A 6-5/8”(168mm)B 8-1/2”(216mm)B 7-3/8”(187mm)B 5-3/4”(146mm)FramedoorB81/4” 6mmD–4550SERIES
d-4550 / d-4551 Series door closerSpecifications T, HT, TCS Application Custom installation template may be available for unusualinstallation conditions. Contact Stanley for assistance.Maximum door opening120 OpeningHold Open Device123Hold Open Angle106 86 80 d-4550/d-4551 track rail Arm Applicationtrack rail Arm Pull Installationdoor31-11/32”34 mm3-13/16”97mm23/32”18 mm21-1/32”534 mmFramedoor13-1/32”331 mm5-19/32”142 mm1-5/32”29 mm1-5/32”30 mm21/8”3mm13-7/8”98mmFrametracK raIl arM aPPlIcatIontrAcK rAIL ArM (PuLL) APPLIcAtIon2-7/16”62 mmdrop Plate Installation P45-180 (For drop plate dimensions see page mm7/8”22mm1-1/2”38mmC LO S E R /32”18mm1/2”–13mmdoor1/4”6mm9
sInGle PoInt Hold-oPen (PUll) aPPlIcatIonSInGLE PoInt HoLd-oPEn (PuLL) APPLIcAtIond-4550EH Electronic Hold-open Series door closerThe D-4550EH Easy-Set Series provides convenient electronic hold-openfeatures for a variety of swing door applications. When energized, theunit is held at a field selectable degree of hold-open incorporating a24VDC solenoid located in the track-arm.Features Field adjustable degree of hold-open Non-handed Available in six standard finishes Smooth safe manual engagement/disengagement Convenient system check switch Field adjustable hold-open forceListings UL Listed for smoke barrier orlabeled fire doors UL Listed for self closing doorswithout hold-open ANSI/BHMA A156.15 NFPA 101d-4550EH Hold open (Pull) ApplicationElectrical SpecificationsVoltage: 24VDCAmpere: 0.15 ampererArm Length12 23/32” 13 1/16” 13 7/16” 13 25/32” 14 1/8” 14 1/2” 14 27/32” 15 3/16” 15 9/16” 15 29/32” 16 1/4” 16 5/8” 16 31/32”323mm 332mm 341mm 350mm 359mm 368mm 377mm 386mm 395mm 404mm 413mm 422mm 431mmHold open 1º137º144º153ºPull-Side Installationrecommended: Install an auxillarystop at the hold-open angle.(see arm adjustment chart above)drop Plate Installation P45-180 (For drop plate dimensions see page 13.)10D–4550SERIES
d-4550EH Electronic Hold-open Series door closerThe D-4550EH Easy-Set Series provides convenient electronic hold-openfeatures for a variety of swing door applications. When energized, theunit is held at a field selectable degree of hold-open incorporating a24VDC solenoid located in the track-arm.ListingsFeatures Field adjustable degree of hold-open UL Listed for smoke barrier orlabeled fire doors Non-handed UL Listed for self closing doors Available in six standard finisheswithout hold-open Smooth safe manual engagement/ ANSI/BHMA A156.15disengagement NFPA 101 Convenient system check switch Field adjustable hold-open forced-4550EH Hold open (Push) ApplicationElectrical SpecificationsVoltage: 24VDCAmpere: 0.15 ampererArm Length12 23/32” 13 1/16” 13 7/16” 13 25/32” 14 1/8” 14 1/2” 14 27/32” 15 3/16” 15 9/16” 15 55/64” 16 1/4” 16 5/8” 16 31/32”323mm 332mm 341mm 350mm 359mm 368mm 377mm 386mm 395mm 404mm 413mm 422mm 431mmHold open 120º126º129ºPush-Side Installationrecommended: Install an auxillarystop at the hold-open angle.(see arm adjustment chart above)sInGle PoInt Hold-oPen (PUsH) aPPlIcatIonSInGLE PoInt HoLd-oPEn (PuSH) APPLIcAtIondrop Plate Installation P45-180D (For drop plate dimensions see page 13.)DOORC LO S E R S11
accessorIesAccESSorIESStandard Arm Set A45-501Standard Hold-open Arm Set A45-501HStandard Arm Set with Long rodand Shoe Set A45-501L For reveals from 2-1/2” to 8”Standard Hold-open Arm with Long rod and Shoe SetA45-501HL For reveals from 3-3/16” to 4-13/16”A45-501HXL For reveals from 4-7/8” to 8”Note: Long Rod used onPUSH sideHeavy duty Parallel Arm SetA45-505Heavy duty Parallel Arm Set with Hold openA45-505HHeavy duty Parallel Arm Set with StopA45-505SHeavy duty Parallel Arm Set with Stop and Holdopen A45-505HSHeavy duty Parallel Arm Set with compression Stop A45-505cSHeavy duty Parallel Arm Set with compressionStop and Hold open A45-505HcSA45-505SHeavy Duty Parallel Arm Set with StopParallel Hold-open Arm Set A45-503H12Note: Long Rod used onPUSH sideA45-505HSHeavy Duty Parallel Arm Set with Stop and Hold OpenEH Arm Hold-open A45-507EHD–4550SERIES
drop Plate – P45-180drop Plate – t Plate to mount to Lcn 4111 Hole Pattern (Heavy dutyArm) – P45-4110 (non-handed)retrofit Plate to mount to Lcn 4040 Hole Pattern (Heavy dutyArm) – P45-4040 terial Thickness: 3/16”Mc-455 – Full Metal cover (optional)3-13/16”3-13/16”c-455 – Full Plastic ck rail Arm Set A45-507t11-13/16”20-1/4”C LO S E R S13
accessorIesAccESSorIEStrack rail Arm Set A45-507tcS Includes internal bumper for compression stoptrack rail Hold-open Arm Set nternal bumper507t-17 Track Hold Opentrack rail Electronic Hold-open Arm Set A45-507EHElectronic Hold open – Side viewElectronic Hold open – top view3-1/2”141”Spacer Block for Mounting Hd PA Bracket onrabbet – P45Hd-110HL.1”Spacer Block for Standard Arm Mounting PA Bracket on rabbet– P45-1101/2”3-1/2”D–45501/2”SERIES
Angle Bracket for Mounting Standard PA Bracket on Flushtransom – ��3/4”1-3/4”3”1-1/4”Angle Bracket for Mounting Hd PA Bracket on Flush transom 4”3/8”3-1/2”Angle Bracket for Shoe Support on Hd Arms – P45Hd-112,used as 5th screw on narrow rabbets1 1/2”Angle Bracket - P45-190 used on top jamb applications withoutany top /8”11-3/4”1-1/2”1-3/4”Extra-clearance offset Soffit Plate – P45-113compression & threaded 177Threaded Stop Insert(Used on A45-505S �M14A45-507tcS – Compression Stop(Used on A45-505CS Arm)DOORC LO S E R S15
stanley door closers d-1610/d-1611For more information on Stanley Security Solutions’ products, services, and office locations visit our web site at www.stanleysecuritysolutions.comProduct information contained in this catalog has been compiled and presented with as much care and completeness as is reasonably possible.Errors or mistakes may be present, and in many cases, reliance has been placed on information supplied by other manufacturers which may be inerror or which may be subject to changes or modifications by the manufacturer without notice and without obligation. Therefore, no guarantee canbe made or should be assumed or implied with regards to product information contained in this catalog.Stanley Security Solutions, Inc.6161 E. 75th Street Indianapolis, Indiana 46250 2013 Stanley Security Solutions, Inc. 05SERIES
d-4550 / d-4551 Series door closer Specifications Can be templated for either 120 or 180 (when butt, frame and wall conditions permit.) Custom installation template may be available for unusual installation conditions. Contact Stanley for assistance. Hold-open points up to maximum door opening with hold open arm. Standard Installation
