WIXLIB

IMPACT WRENCHESIMPACT WRENCHMODEL IW12SPECIFICATIONSFEATURESWeight: 18 lbs / 8 kgLength: 9.5 in. / 24 cmWidth: 4 in. / 10 cmCapacity: 3/4 in. / 1.9 cm Square DriveFlow Range: 4-12 gpm / 15-45 lpmPressure: 1000-2000 psi / 70-140 barTorque: 250-1200 ft lbs / 340-1632 Nm Adjustable impact intensity. Swing-hammer design. Larger feathering trigger. Standard reversing valve. Handle coating transmits less heat.ORDER INFORMATIONDescriptionIncluded EquipmentIW12140SModel3/4 in. Square DriveHTMA Flush-Face Couplers, Hose WhipsIW12140013/4 in. Square DriveHTMA Flush-Face Couplers, Hose Whips, CEIMPACT WRENCHSPECIFICATIONSFEATURESWeight: 26 lbs / 11.8 kgLength: 14.5 in. / 36.8 cmWidth: 4.5 in. / 11.4 cmCapacity: 7/16 in. or 1/2 in.Flow Range: 12 gpm / 45 lpmPressure: 1000-2000 psi / 70-140 barTorque: 500-2500 ft lbs / 680-3400 Nm Adjustable impact intensity. Swing-hammer mechanism. Large “D” handle and feathering On/Off valve. Standard reversing valve. Available Extended Handle Mechanism.ORDER INFORMATIONModelIW16150SDescriptionIncluded Equipment1 in. Square DriveHTMA Couplers and Hose WhipsOPTIONAL EQUIPMENT Adapter, 1 in. to 3/4 in. Drive 10 in. Extension, 3/4, 1 in. Drive Remote Handle Assembly Railroad Socket Set, 1 in. Square Drive Socket Pin Socket RingStanley’s hydraulic impact wrenches are world renowned for their adjustable impact intensity settings allowing fora wide range of uses. The rugged design incorporates an integral motor and heavy-duty mechanism for the rigors oftrack maintenance use. The power-to-weight ratio of these products are un-matched by any impact wrench on themarket in their class.8 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOGMODEL IW16

RAIL DRILLRAIL DRILLMODEL RD12Note: Rail Drills do not operate without bits.The power of the RD12 when used inconjunction with our exclusive indexablecarbide tipped bits easily drills bothhardened and standard rail with the sametool, providing the lowest cost per holeavailable on the market.Width: 8 in. / 20.3 cmWater Capacity: 2 gallons / 7.6 litersSPECIFICATIONSFEATURESWeight: 58.5 lbs / 26.5 kgLength: 28 in. / 71.1 cm Lightweight aluminum construction. Preset integrated water flow control. Over-center clamp design. Tool rack for extra bits. Automatic water/coolantcontrol valveFlow Range: 8-10 gpm / 30-38 lpmPressure: 2000 psi / 140 barFeed Rate per Revolution:.0013 in. / .03 mmOPTIONAL EQUIPMENT Bits 1 in. - 1-9/16 in. (22 mm - 36mm) Indexable Carbide Tips Templates Hose WhipsORDER INFORMATIONModelDescriptionIncluded EquipmentRD12101Rail Drill with Water Tank, CECouplers and Torx DriverStanley offers a wide variety of its exclusive Indexable Carbide tipped bits.RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG // 9

RAIL SAWRAIL SAWMODEL RS25Model RS25103 ShownStanley’s RS25 Rail Saw with itsbell-crank style clamp design providespositive, rigid locking to all types of railfor quick and accurate set-up.The ergonomical long saw arm isstandard with the RS25 and allowsthe operator full use of the tool ina standing position. The indexableswivel on the clamp arm and saw,allows cutting on both sides of therail, eliminating the need to disconnectfrom and re-connect to the saw clamp.SPECIFICATIONS Lockable lower arm significantlyreduces operator effort. Indexable swivel on the clamp arm. Tamper-proof speed control. Sealed bearings in arm and pivot joints. Available in 14 and 16 inch models. Cast aluminum construction. Integrated retractable bladeposition guide.Saw & Clamp Weight: 56 lbs / 25 kgSaw Weight: 33 lbs / 15 kgLength w/o Wheel: 36 in. / 92 cmWidth: 11 in. / 28 cmDepth: 18 in. / 46 cmFlow Range: 8-10 gpm / 30-38 lpmPressure: 2000 psi / 140 barSpindle Speed: 4000 RPM w/ 16 in. Wheel4500 RPM w/ 14 in. WheelOPTIONAL EQUIPMENT RAIL SAW BLADESFEATURES 16 in. Norton Norzone III Fastcut 16 in. Norton AT-36 14 in. Norton Norzone III Fastcut Universal Bell Crank Kit Bell-crank style clamp design. Ergonomically designed long saw arm.ORDER INFORMATIONModelDescriptionIncluded EquipmentRS2510316 in.Clamp, Couplers and Hose WhipsRS2511314 in.Clamp, Couplers and Hose Whips10 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOGRail Clamp

TRACK JACKTRACK JACKMODEL TJ10SPECIFICATIONSFEATURESWeight: 43.5 lbs / 19.7 kgBase Length: 11 in. / 27.9 cmHeight (Collapsed): 14.5 in. / 36.8 cmStroke (Total Lift): 8.9 in. / 22.6 cm Narrow bridge model available. One piece forged base. Low pump handle effort.Lifting Capacity: 10 Tons / 9,072 kgAmount of Travel per PumpStroke: .15 in. / 3.8 mmORDER INFORMATIONModelTJ10111M, Integral Pump, Hydraulic Jack w/ Pump HandleTJ10112M, Integral Pump, Narrow Base Bridge JackTOOL EXCHANGE VALVEThe Tool Exchange Valve is intended to function as a momentaryon/off valve that, when plumbed between a tool and the endhose, will allow the end user to change tools without having toturn off the hydraulic circuit.In the “On” position, hydraulic flow will flow through thevalve to the tool, allowing the tool to operate normally. In the“Off” position, hydraulic flow will be blocked at the valve,allowing the tool to be disconnected and an alternate tool tobe attached. Shifting the valve back to the “On” position willresume hydraulic flow to the alternate tool.NOTE: With constant flow (open center) hydraulic systems,shifting the valve to the “off” position will force all hydraulicflow through the system's relief valve. It is therefore intendedfor tool exchange only and should not be left in the “off”position for longer than 30 seconds.SPECIFICATIONSLength: 3 in. / 76.2 mmWidth: 1.5 in. / 38.1 mmHeight: 3.75 in. / 95.25 mm(Valve only - does not include hose whips and couplers)FEATURES Low friction seals Seal wipers on the on / off spool Replaceable seal caps Hardened, Stainless steel spoolStanley’s track jacks are the best jacks available with untouchable power-to-weight ratios and impressive lifting capacity.RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG // 11

DRILLSDRILLThe DL07 Drill is ideal for drilling holes in wood, metal and masonry. It features instant reverse for high reliabilityand efficiency in all types of drilling applications.MODEL DL07SPECIFICATIONSFEATURESSPEED/HYD. FLOWWeight: 6 lbs / 2.7 kgLength: 9 in. / 23 cmCapacity: 1/2 in. Chuck / 12 mm ChuckMax. Flow: 12 gpm / 45 lpmMax. Pressure: 2000 psi / 140 bar Hyvrevz gear-type motor. Oversized feathering trigger.350 rpm @ 3 gpm / 11.3 lpm475 rpm @ 4 gpm / 15 lpm750 rpm @ 6 gpm / 23 lpm1000 rpm @ 8 gpm / 30 lpm1250 rpm @ 10 gpm / 38 lpm Increased operator comfort. Dual position Assist Handle. Built-in reverse flow check valve. Handle coating transmits less heat.ORDER INFORMATIONModelDL07550DescriptionIncluded EquipmentOC/CC, Dual Spool, 1/2 in. ChuckTrigger Guard, Assist Handle, CouplersDL0755001OC/CC, Dual Spool, 1/2 in. Chuck, CETrigger Guard, Assist Handle, CouplersDL07572SDual Spool, 5/8 in. ChuckTrigger Guard, Assist Handle, CouplersOPTIONAL EQUIPMENT 7/16 in. Shank Carbide Tipped Augers 9/16, 11/16, 13/16 in. Dia, 8 in. Twist, 12 in. OAL 9/16, 11/16, 13/16, 15/16, 1-1/16 in.Dia, 12 in. Twist, 16 in. OAL 9/16, 11/16, 13/16, 15/16, 1-1/16 in.Dia, 18 in. Twist, 22 in. OAL 11/16 in. Dia, 32 in. Twist, 36 in. OAL 13/16 in. Dia, 36 in. Twist, 48 in. OAL 13/16 in. Dia, 15 in. Twist, 18 in. OALThe ID07 Impact Drill/Wrench delivers impact torque of up to 500 ft lbs (675 Nm). It is capable of breaking loose someof the toughest bolts and nuts. The ID07 can drive wood augers into the hardest salt-cured or creosote-treated poleswithout reaction torque to the operator.SPECIFICATIONSFEATURESWeight: 7 lbs / 3.3 kgLength: 8.5 in. / 21.6 cmCapacity: 7/16 in. or 1/2 in.Max. Flow: 12 gpm / 45 lpmMax. Pressure: 2000 psi / 140 bar Hyrevz gear-type motor. Swing-hammer mechanism. 7/16 in. hex quick-change chuckor 1/2 in. square drive. Built-in reverse flow check valve. Handle coating transmits less heat.DRILLMODEL ID07ORDER INFORMATIONModelDescriptionIncluded EquipmentID07810017/16 in. Quick Change Chuck, CECouplersID07810S7/16 in. Quick Change ChuckCouplersID078157/16 in. Quick Change ChuckTrigger GuardID078201/2 in. Square DriveTrigger Guard, Couplers1/2 in. Square Drive, CECouplersID0782001OPTIONAL EQUIPMENT Adapter, 7/16 Male Hex x 1/2 Male Square Adapter, 1/2 Female Square x 5/8 Hex QC Lineman’s Socket, 13/16, 15/16, 1, 1-1/8 Impact Socket Set, 1/2 Sq Drive, 8-Point, Deep Sockets(Includes Vinyl Holder & 1/2, 9/16, 5/8, 11/16, 3/4,13/16, 7/8, 1, 1-1/16) 7/16 in. Shank Carbide Tipped Augers 9/16, 11/16, 13/16 in. Dia, 8 in. Twist, 12 in. OAL 9/16, 11/16, 13/16, 15/16, 1-1/16 in.Dia, 12 in. Twist, 16 in. OAL 9/16, 11/16, 13/16, 15/16, 1-1/16 in.Dia, 18 in. Twist, 22 in. OAL12 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG 11/16 in. Dia, 32 in. Twist, 36 in. OAL 13/16 in. Dia, 36 in. Twist, 48 in. OAL 13/16 in. Dia, 15 in. Twist, 18 in. OAL

POWER UNITSPOWER UNITMODELS GTR09 / GTR20The Hydraulic power to operate Stanley’s line of hydraulicrailroad tools compact design is ideal for all your on-sitehydraulic power needs. The ultra efficient hydraulic toolcircuit cooling provides comfortable tool operation even inthe most demanding environments.SPECIFICATIONSWeight: 330 lbs / 150 kgLength: 35 in. / 90 cmWidth: 23 in. / 59 cmHeight: 29 in. / 74 mmPressure: 2000 psi / 140 barFuel Capacity: 5.5 gal. / 24 literFEATURES Compact and lightweight. Computerized electronic throttle control. In-tank hydraulic filtration. Pressurized engine oil lubrication. Locking handle. Electric Start.GTR20ORDER INFORMATIONModelGTR20B02GTR20B06Description(1), 10 gpm / 38 lpm or (2), 5 gpm / 20 lpm18 hp Briggs & Stratton (Gas Powered)Skid Mount, (1), 10 gpm / 38 lpm or (2),5 gpm / 20 lpm18 hp Briggs & Stratton (Gas PoweredIncluded EquipmentAuto Throttle, Wheels and HandlesAuto Throttle, Wheels and HandlesOPTIONAL EQUIPMENT 12 Volt accessory outlet.RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG // 13

WELD SHEARWELD SHEARMODEL WS10Stanley’s powerful yet light-weightWeld Shear is the ideal tool for shearingthermite welds with a shearing forceof over 20,000 lbs (89,000 Nm).The WS10’s efficient design allowswelds to be sheared prior to dismantlingthe weld mold, decreasing the timeto set up and increasing productivity.The in-line pump handle eliminatesrocking of the shear on the rail duringshearing operation.WS10321Afor WS1032101AWidth: 19.5 in. / 49.5 cmHyd. Pressure: 2000 psi / 140 barFlow Range: 3-10 gpm / 12-38 lpmShear Force: 20,000 lbs / 89,000 NmFEATURES 10 Ton / 9 Metric Tons shearing force. Efficient hand pump. In-line handle. Controls placed away from shearfor operator safety. 4 self-locking hold downs. Replaceable rollers.SPECIFICATIONSWeight: 90 lbs / 41 kgLength: 29 & 32.5 in. / 73.7 & 82.5 cmfor WS10301 and WS10200, 28 in / 71 cmORDER INFORMATIONDescriptionIncluded EquipmentWS10321AModelLightweight Weld ShearBlade Set “A” (132 lb Rail - 27948)WS10321ABLightweight Weld ShearAero Quip Couplers, Blade Set “A”(132 lb Rail - 27948)WS1032101AWeld Shear (CE Power Unit)WS1022001AWeld Shear Hand Pump, CEWS102200AWeld Shear Hand Pump, Light WeightOPTIONAL EQUIPMENTItem No.Description27948Blade Set A (105 - 155 lb / yd [47 70 kg / M] Rail*)27989Blade Set B (60 - 130 lb / yd [41 - 60 kg / M] Rail*)35742Blade Set C (60 - 90 lb / yd [36 - 60 kg/ M] Rail*)* Depends on Rail Type14 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOGBlade Set “A” (132 lb Rail - 27948)

GRINDERSFROG GRINDERMODEL FG10SPECIFICATIONSFEATURESWheel Capacity: 6 in. / 15 cmArbor Size: 5/8 in. - 11Optimum Flow: 10 gpm / 38 lpmHyd. Pressure: 2000 psi / 140 barSpindle Speed: 4000 RPMLength: 44 in. / 112 cmWidth: 10.5 in. / 27 cmWeight: 85 lbs / 41 kg Upright handle for ergonomic operation. 3-position pivot at both ends allows for 3 separate grinding operations. Interlocking, full length, bail type safety trigger. Sealed height adjustment mechanism for infinite angle adjustment. Removable wheel guard for easy access to the grinding wheel. Built-in speed control. Extension for Grinding Frog Points Spark GuardOPTIONAL EQUIPMENTORDER INFORMATION Grinding StonePROFILE GRINDERMODEL PG10ModelDescriptionIncluded EquipmentFG10110Frog GrinderCouplersSPECIFICATIONSFEATURESWheel Capacity: 6 in. / 15 cm Upright handle for ergonomic operation. Adjustable flange wheels ensure grinding accuracy. Interlocking, full length, bail type safety trigger. Removable wheel guard for easy access to the grinding wheel. Built-in speed control.Arbor Size: 5/8 in. - 11Optimum Flow: 10 gpm / 38 lpmHyd. Pressure: 2000 psi / 140 barSpindle Speed: 4000 RPMLength: 44 in. / 112 cmWidth: 20 in. / 51 cmWeight: 118 lbs / 53.5 kgOPTIONAL EQUIPMENT Grinding Stone Spark GuardORDER INFORMATIONModelPG10110DescriptionIncluded EquipmentProfile Grinder w/ Shaft WrenchCouplers, Shaft WrenchThe FG10 Frog Grinder is ideal for grinding frogs, rail ends or mismatched rail. While the PG05 and PG10 Profile Grinders aredesigned to grind a wide range of rail from 90 to 141 pound.RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG // 15

GRINDERSGRINDERSPECIFICATIONSMODEL GR60OPTIONAL EQUIPMENTWheel Capacity: 6 in. / 15 cmArbor Size: 5/8 in. -11Optimum Flow: 10 gpm / 38 lpmHyd. Pressure: 2000 psi / 140 barSpindle Speed: 4000 RPMLength: 18 in. / 46 cmWidth: 10.5 in. / 27 cmWeight: 20 lbs / 9 kg Grinding StoneORDER INFORMATIONModelDescriptionIncluded EquipmentGR60121S6 in. Grinder w/ Counter-Clockwise RotationCouplers and Hose WhipsSPECIFICATIONSOPTIONAL EQUIPMENTWheel Capacity: 2.5 in. ConeArbor Size: 5/8 in. -11Optimum Flow: 10 gpm / 38 lpmHyd. Pressure: 2000 psi / 140 barSpindle Speed: 5500 RPMLength: 23 in. / 59 cmWidth: 3.3 in. / 8 cmWeight: 11 lbs / 5 kgGRINDER Grinding StoneMODEL HG60ORDER INFORMATIONModelHG60130BGRINDERDescriptionIncluded Equipment2-1/2 in. Diameter Bull Nose GrinderCouplers and Hose WhipsMODEL HG80SPECIFICATIONSOPTIONAL EQUIPMENTWheel Capacity: 8 in. / 20 cmArbor Size: 5/8Optimum Flow: 10 gpm / 38 lpmHyd. Pressure: 2000 psi / 140 barSpindle Speed: 5500 RPMLength: 23 in. / 59 cmWidth: 10 in. / 25 cmWeight: 14 lbs / 6 kg Grinding StoneORDER INFORMATIONModelDescriptionHG80110BHorizontal Grinder w/Counter-Clockwise Rotation, 8 in. WheelHG80120BHorizontal Grinder w/Clockwise Rotation, 8 in. WheelFEATURES Highest power-to-weight ratio in the industry. Designed to match power/rpm to specific applications. Interlocking trigger prevents accidental engagement. Built-in flow control prevents excessive spindle speed. Rugged lightweight construction.The GR60 Cup Stone Grinder was designed to meetrugged grinding needs while the HG60 Bull Nose Grinderis ideal for grinding and de-burring drilled holes in rail.The HG80 provides an ideal grinding tool from cleaningup a thermite weld to grinding a radius on frogs.16 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOGIncluded EquipmentCouplers andHose WhipsCouplers andHose Whips

ROBOTIC WELDERROBOTIC WELDERMODEL RW30The Patented RW30 Robotic Welder is a computercontrolled welder. It is ideal for repairing rails or frogs.Height: 16 in. / 400 mmInput Power Required: 115-230 V / 50-60 HzThe RW30 provides consistent high quality welds.FEATURESSPECIFICATIONS (RW30110)Weld Zone Length: 15.75 in. / 40 cmWeld Zone Width: 13.75 in. / 34.9 cmWeld Speed (Estimated): 5.0 in./minute/ 32 cm/minuteWeld Travel Speed: 7.8 to 15.7 in./minute /19.8 to 39.8 cm/minuteWeight: 65 lbs / 29.5 kgLength (Less Handles): 25.6 in. / 650 mmWidth: 29 in. / 740 mm Eliminates operator exposure to weld fumes. Records all welding events into memory for laterdownload to PC. Memory adapter, PC adapter, and softwareavailable as an option. Automated control provides consistent welds. Weld bead, patterns, and dimensions allelectronically controlled. Automatic call-up from memory. Rugged lightweight construction.Model RW30110 Robotic Welder ShownORDER INFORMATIONModelINCLUDED WITH ALL ionIncluded EquipmentFrog Clamps, Clamps, Stick Out Gauge,Robotic Welder, 400 mm Travel, No Wire FeedComputer ControlAbove with Heater for coldRobotic Welder, 400 mm Travel, No Wire Feedweather operationFrog Clamps, Clamps, Stick Out Gauge,Robotic Welder, 1000 mm Travel, No Wire FeedComputer ControlOPTIONAL EQUIPMENT Welding Generators Angle Head Carbon Frog Inserts Cable to Rail Clamps Track Wheel Kit Wire Feeders Welding Wire PC Software PC Hardware Rail Preheaters Pull Gun Roll ‘un RollBarcode Pen ReaderStick-out GaugeRAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG // 17

TRAC HORSETRACHORSEMODEL MHP3The TracHorse is an all-terrain, self-propelled mobile hydraulic tool and equipment carrier that allowstransportation of tools and equipment in most job site environments. Simple operating controls allow formaneuvering in a wide range of applications. The auxiliary hydraulic tool circuit is designed for continuousduty applications and features the standard high-efficiency cooling found on all Stanley hydraulic power units.SPECIFICATIONSFEATURESLoad Capacity: 1000 lbs / 454 kgTravel Speed: Low Speed - 1.55 mph / 2.5 km/h Self-Propelled - Mobile hydraulic tool andequipment carrier that transports tools andequipment in most job-site environments. Simple Operating Controls - Allows for a widerange of applications. Two Speed Track Drive. Work Lights. Opening Tailgate. Auxiliary Hydraulic Tool Circuit - Is designedfor continuous-duty applications and featuresthe standard high-efficiency cooling foundon all Stanley hydraulic power units. Climbs 60% grade. Carries 1,000 lbs / 454 kg.High Speed - 2.8 mph / 4.5 km/hWeight: 1125 lbs / 510 kgLength: 78 inches / 198 cmWidth: 36 inches / 92 cmHeight: 43 inches / 109 cmPressure: 2000 psi / 38 barFlow Range: Twin Circuit - 2 @ 5 gpm / 20 lpmor 1 @ 10 gpm / 38 lpmConnect Size & Type: Flush-Face CouplersFuel Capacity: 5.5 gallons / 21 litersHydraulic Capacity: 3 gallons / 11 litersEngines: OHV Gas or Kohler/Ruggerini 19 hp DieselORDER INFORMATIONModelDescriptionMHP32242100Twin Circuit, Honda EngineMHP32342100Diesel Engine18 // RAILWAY PRODUCTS: MAINTENANCE OF WAY PRODUCT CATALOG

CHAIN SAWCHAIN SAWMODEL CS06The CS06 Chain Saw offers the highestpower-to-weight ratio of any chain sawon the market today. All models featureinterlocking triggers, hand guards, lowkick-back bars and chains.Because hydraulic power doesn’trequire a flywheel to smooth powerpulses, there is no chain coasting whenthe trigger is released.The CS06 pistol-grip chain saw is idealfor timber tie/sleepers.Flow Range: 7-9 gpm / 26-34 lpmOptimum Flow: 8 gpm / 30 lpmFEATURES Low kick-back. Wide variety of ba

intelligence is the foundation for the Railroad Tools product line at Stanley Hydraulic Tools. Stanley Hydraulic Tools is also proud of its ISO 9001-2008, ISO 1401-2004, and OHSA 18001-2007 certifications. MAJOR PRODUCT LINES MANUFACTURED INCLUDE: Railroad Track Maintenance Tools, Signal and Communication Tools, Catenary Tools