Transcription
DishwasherInstallation ManualDW 51600 SSDWT 52600 SSIHDW 51600 FBIDWT 52600 BIHDWT 51600 SSDWT 52800 WIHDWT 51600 FBIDWT 52800 SSIHDWT 81800 FBIDWT 81900 FBIDWT 81800 SSDWT 51600 WDWT 81800 SSIHDWT 81900 SSDWT 81800 SSWSDWT 52600 WIH
DishwasherInstallation ManualDW 51600 SSDWT 52600 SSIHDW 51600 FBIDWT 52600 BIHDWT 51600 SSDWT 52800 WIHDWT 51600 FBIDWT 52800 SSIHDWT 81800 FBIDWT 81900 FBIDWT 81800 SSDWT 51600 WDWT 81800 SSIHDWT 81900 SSDWT 81800 SSWSDWT 52600 WIH
To prevent accidents, which could cause serious injury or death, as well asmachine damage read these instructions before installation and / or use.INTRODUCTION11. IMPORTANT SAFETY INSTRUCTIONS12. TOOLS WHICH MAY BE NEEDED33. MATERIALS WHICH MAY BE NEEDED34. MATERIALS SUPPLIED45. DISHWASHER SPECIFICATIONS56. ENCLOSURE PREPARATION61.1 INSPECT THE DISHWASHER4.1 PARTS SUPPLIED4.2 MANUAL BAG4.3 DISHWASHER PARTS BAG 14.4 DISHWASHER PARTS BAG 24.5 PARTS ATTACHED TO THE REAR OF THE DISHWASHER5.1 TECHNICAL FEATURES24444456.1 ELECTRICAL PREPARATION6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETS6.3 ADJUSTING HEIGHT6.4 INSTALLING THE SIDE TRIM STRIPS6.5 PREPARING THE WATER CONNECTION (A)6.6 DRAIN PREPARATION6.7 STEAM PROTECTION FOIL66991010127. PLACEMENT OF DISHWASHER INTO THE OPENING138. INSTALLER CHECKLIST239. SELF HELP HINTS:237.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICAL CONNECTIONS7.2 READJUSTING FOOT LEVELS7.3 ADJUSTING THE MOVABLE TOE KICK7.4 FIXING THE CABINET TO THE COUNTER7.5 PREPARING THE TIMBER DOOR7.6 PREPARING THE PRODUCT DOOR7.9 INSTALLING THE TIMBER DOOR7.10 FIXING THE TIMBER DOOR7.11 FIXING THE TIMBER DOOR7.12 ADJUSTING THE KICK PLATE7.13 CONNECTION1315151718192020212122
INTRODUCTIONWARNINGPlease read this installation manualand particularly the safety instructionscompletely and carefully. They will save youtime and effort and help to ensure optimumdishwasher performance.When installing the dishwasher, followbasic precautions, including thefollowing: The dishwasher could only be convertedfrom cord-connected to permanentlyconnected by an authorized servicerepresentative. (If needed contact yourdealer to schedule an authorized serviceagent for conversion with an appropriateconversion kit) Installation and repair should beperformed by a qualified installer.Work by unqualified persons could bedangerous and may void the warranty.Be sure to observe all listed warnings andcautions. Look particularly for the icons withexclamation marks inside. The informationicon also will provide important references. NOTICE :WARNING:Indicates a potentially hazardous situationwhich, if not avoided, could result in deathor serious injury.CAUTION:Indicates a potentially hazardous situationwhich, if not avoided, may result in injury.It may also be used to alert against unsafepractices.NOTICE:Indicates a potentially hazardous situationwhich, if not avoided, may result in damageto the dishwasher, the table-ware, theequipment or the environment.1. IMPORTANT SAFETYINSTRUCTIONSIn addition to these instructions, thedishwasher shall be installed: In accordance with all local codes or, inabsence of a local code, In the United States, with the NationalElectric Code, In Canada, with the Canadian ElectricCode C22.1-latest edition/Provincial andMunicipal codes and/or local codes.NOTICE :Read these installation instructionscompletely before installing and follow themcarefully. Save these installation instructionsand pass them on to any future user.1The dishwasher should be installed byan insured licensed plumber, contractoror trained installer. Installation performedby persons other than this could result inimproper installation and property damage. Do not operate the appliance if damaged,malfunctioning, partially disassembled orif it has missing or broken parts. Also follow the safety instructions of theuser manual. To reduce the risk of electric shock, fire,or injury to persons, the installer mustensure that the dishwasher is completelyenclosed at the time of installation. Only connect the dishwasher to thepower supply when all installation andplumbing work is complete. If the dishwasher is installed in a locationthat experiences freezing temperatures(e.g. in a vacation home, cabin, etc.),you must drain all the water from thedishwasher’s interior. Water systemruptures that occur as a result of freezingare not covered by warranty. Dishwasher must be secured to adjacentcabinetry using the brackets provided.Failure to do this may cause damage toproperty or bodily injury. Connect to a properly rated, protectedand sized power supply circuit to avoidelectrical overload. The dishwasher isUSA
1.1 INSPECT THE DISHWASHERdesigned for an electrical supply of 120 V(volts), 60 Hz (hertz), AC, connected to adishwasher-dedicated, properly groundedelectrical circuit with a fuse or breakersrated for 15 amperes. Electrical supplyconductors shall be a minimum of # 16AWG copper wire rated at 75 C (167 F) or higher. These requirements mustbe met to prevent injury and machinedamage. Consult a qualified electrician ifin doubt.Do not use any extension cord orportable outlet device to connect thedishwasher to a power supply.Ensure that any plastic wrappings, bags,small pieces etc. are disposed of safelyand kept out of the reach of children.Danger of suffocation!Remove the door to the washingcompartment when removing an olddishwasher from service or discarding it.Ensure that the appliance presents nodanger to children while being stored fordisposal.Old appliances may contain materialsthat can be recycled. Please contactyour local recycling authority about thepossibility of recycling these materials.After unpacking the dishwasher and priorto installation, thoroughly inspect thedishwasher for possible freight or cosmeticdamage. Report any damage immediately.NOTICE : Cosmetic defects must be reported within10 days of installation. Do not discard any bags or items thatcome with the original package untilafter the entire installation has beencompleted.NOTICE : The dishwasher drain hose must beinstalled with a drain loop at least 28”(710mm) off the cabinet floor; otherwisethe dishwasher may not drain properly. This dishwasher is intended forresidential use only, and should not beused in commercial establishments. New installation - If the dishwasher is anew installation, most of the work mustbe done before the dishwasher is movedinto place. Replacement - If the dishwasher isreplacing another dishwasher, checkthe existing dishwasher connections forcompatibility with the new dishwasher,and replace parts as necessary.2USA
2. TOOLS WHICH MAY BE NEEDED3. MATERIALS WHICH MAY BE NEEDED(Additional materials may be required to comply with local codes)Hot Water Supply Line - Minimum 3/8” O.D. copper tubing or metal braideddishwasher supply line.Elbow with 3/8” N.P.T. male threads on one leg, and sized to fit your watersupply line (copper tubing/compression fitting, or braided hose) on theother leg.UL listed conduit connector or strain relief.Teflon tape or other pipe thread compound to seal plumbing connections.Shut-off valve and fittings appropriate for hot water supply line (coppertubing/compression fitting, or braided hose).SiliconeGlue3USA
4. MATERIALS SUPPLIED4.1 PARTS SUPPLIEDParts for your dishwasher willcome in several plastic bags.Check your parts bags shownto make sure you have all theparts as listed to the left.4.2 MANUAL BAGThe dishwasher comes with amanual bag containing: User manual, Installation manual4.3 DISHWASHERPARTS BAG 1This dishwasher bag comeswith the following parts:a. Side Trim Strips (Left)b. Side Trim Strips (Right)d. Screws Ø 1/8” x 5/8” (Ø 3.5mm x 14 mm)e. Mounting Bracket Leftf. Mounting Bracket Righth. Screw Clampk. Toe Kick Bracket - Leftl. Toe Kick Bracket – Rightn. Timber Centeringo. Timber Centering Screwp. Toe Kicks. Templatet. Hook and loop fastenerv. Side centeringz. Steam Protection Foilx64USA4.4 DISHWASHERPARTS BAG 2(MODEL DEPENDING)In addition to the manual bagand the dishwasher parts bag(dishwasher models whichcan accept a wooden kitchendoor) also come with a doorpanel installation kit whichcontains:y. Screws 4mm x 36 mm 3/16th x 1-7/16th4.5 PARTS ATTACHEDTO THE REAR OF THEDISHWASHERa. Side Trim Strips (Left)b. Side Trim Strips (Right)
5. DISHWASHER SPECIFICATIONS5.1 TECHNICAL FEATURESPermissible water pressureElectrical connectionTotal powerHeater power4.35 - 145 psi (0.3 - 10 bars)120 V (volts), 12 A (amps), 60Hz (hertz)1400 W (watts)1100 W (watts)NOTICE :Because we continually strive to improve our products, we may change our specificationsand design without prior notice.This device corresponds to the following directives:UL 749 Household Dishwasher directive.5USA
6. ENCLOSURE PREPARATION6.1 ELECTRICAL PREPARATIONWARNINGThe dishwasher is designed for an electrical supply of 120 V, 60 Hz, AC, connectedto a dishwasher-dedicated, properly grounded electrical circuit with a fuse orbreaker rated for 15 amperes.6.2 PREPARATION FOR INSTALLING MOUNTING BRACKETSWARNINGDishwasher must be secured to adjacent cabinetry using the mounting bracketsprovided. Failure to do this may cause damage to property or bodily injury.e-f)6USA
d)?7USA
j(Depends on model) 50max50( 50mm)Place the two mounting brackets into the top corners of the dishwasher.Fix the mounting brackets (A) to the top corners of the dishwasher, with the screwssupplied.Bend sides of mounting brackets (B) in order to fix from sides (if necessary).TALL TUB MODELS ONLYTighten the plugs on both sidesof your machine (v)8USA
6.3 ADJUSTING HEIGHTIf the height of the enclosure is 337/8” to 357/8”(861 mm - 911mm) adjust supports as shown inthe figure.Supplied (4)Adjust the front foot level with the adjustingwrench to balance and raise the dishwasher to theenclosure height.Adjust the rear foot level with a screwdriver tobalance and raise the dishwasher to the enclosureheight.NOTICE : Make sure the dishwasher is plumb andnotice dishwasher can be placed with a smallclearance under the counter top. Turning the screwdriver in the direction of theblack arrows will bring the dishwasher back feetup. Turning the screwdriver in the direction of thewhite arrows will take the dishwasher rear feetdown.6.4 INSTALLING THE SIDE TRIM STRIPSRemove the adhesive tape (Figure A).Place the trim strips on the front edge of the sidewalls (Figure B).NOTICE : Make sure you use the correct trim strip sincethere is a left and right side strip. The flexiblematerial should be facing forward (Figure B).9USA
6.5 PREPARING THE WATER CONNECTION (A)Install an easily accessible shut-off valve (not supplied) in the water supply line. All solderconnections must be made before the water line is connected to the dishwasher’s waterinlet valve. Water can also be supplied to the dishwasher by using a flexible braided hoseline.Check with your plumbing supply sources for the proper hose and elbow and necessaryfittings for the water supply line. This material is not supplied, and must be purchasedseparately.WARNINGInstallation should be performed by a qualified installer. Work by unqualifiedpersons could be dangerous and may void the warranty.If the dishwasher is installed in a location that experiences freezing temperatures(e.g. in a vacation home, cabin etc.), you must drain all the water from thedishwasher’s interior. Water system ruptures that occur as a result of freezing arenot covered by warranty.6.6 DRAIN PREPARATIONThe dishwasher drain hose may be connected to the drain plumbing in one of three ways(Figure A, B, C).Water Connection10USA
NOTICE : Either one of the above methods must be used or the dishwasher will not operateproperly. A hose that attaches to a sink spray can burst if it is installed on the same water line asthe dishwasher. If your sink has one, it is recommended that the hose be disconnectedand the hole plugged. The total length of the drain hose is 763/4” (1950mm). If a hose extension is required, adrainage hose of equal quality must be used. The maximum length must not exceed 157 ½” (4000mm). Otherwise, the cleaningprocess is negatively influenced.6.6.1 UNDER THE SINK DRAINInstall a Y-branch tail pipe. (Figure A)NOTICE :You must add a loop at least 28” (710mm) above the floor ofthe cabinet and above the drain connection in the drain hoseto prevent waste water from not draining properly, and causingeither poor washing results or a bad odor.6.6.2 INSTALLING AN AIR GAPIf the local ordinance requires an air gap (Figure B).NOTICE :Check with local ordinance for type of air gap required.6.6.3 DISPOSALRemove the drain connection plug before attaching the drainhose from the dishwasher.Every disposal has a hook up for a dishwasher; consult yourdisposer manual for correct connection. (Figure C)11USA
6.7 STEAM PROTECTION FOILSteam will form inside the dishwasher during operation. At the end of the cycle, when thedishwasher door is opened, it is required to use a steam protection foil to prevent anysteam from collecting on the underside of the counter top.6.6.2 FITTING THE PROTECTION FOILBefore applying the steam protection foil to theunderside of the countertop, clean the area witha damp cloth (as shown in Figure A). Once thearea dries, apply the steam protection foil.The steam protectionfoil will be applied at thelocation where the hotsteam escapes when youfirst open the door (asshown in Figure B).CAUTIONSteam protection foil must be appliedwhere the steam escapes when door isfirst opened. Failure to install the steamprotection foil during installation canlead to damage to the cabinets andcountertop.12USA
7. PLACEMENT OF DISHWASHER INTO THE OPENINGNow place the dishwasher into the opening and get ready to connect all hoses andelectrical connections.CAUTIONMake sure all hosesare pulled through theside opening of thecabinet, no hoses arekinked and all slack istaken out as shown inthe above figure.7.1 DRAIN HOSE CONNECTION, WATER SUPPLY & ELECTRICALCONNECTIONS7.1.1 DRAIN HOSE CONNECTIONConnect the drain hose to the drain plumbing.1. Use the supplied rubber connection hose and drain hose clamps to connect thedishwasher drain hose to the plumbing drain connection.2. Use the spring clamp to secure the rubber connection hose to the dishwasher drainhose. Use the screw clamp to secure the rubber connection hose to the plumbing drainconnection.Note that the markson the rubberconnection hoseshould be on the drainhose side13USA
7.1.2 WATER SUPPLY CONNECTIONWater supply may be connected to thedishwasher in one of two ways: With metal braided hose. With copper tubing.CAUTION Hot water supply line: Use minimum 3/8”O.D. copper tubing or metal braideddishwasher supply line. Temperatures required for soldering andsweating will damage the dishwasher’swater inlet valve so if any such operationis needed, keep the heat sourcemin. 77/8” (200mm) away from thedishwasher’s water inlet valve. There should not be any sharp bends inthe water line that may restrict the waterflow. Teflon tape or pipe tread compoundmust be used for sealing the connection.Before connecting the copper watersupply line to the dishwasher, flush it withhot water to clear any foreign material.NOTICE :After connections are made turn on thewater supply to check for leaks.7.1.3 ELECTRICAL CONNECTIONWARNING Make sure the voltage and frequencylisted on the data plate correspond withthe household electrical supply. This datamust correspond to prevent injury andmachine damage. Consult a qualifiedelectrician if in doubt. Only connect the dishwasher to themains when all installation and plumbingwork is complete. Do not use any extension cord orportable outlet device to connect thedishwasher to a power supply. The power-supply receptacle for theappliance shall be installed in a cabinetor on a wall adjacent to the undercounterspace in which the appliance is to beinstalled.14 The access hole of the supply cord to theinstallation compartment must be smoothand rounded and it must be large enoughfor the attachment plug to pass through.The longest dimension of the openingshall not be more than 1,5” (38 mm).If thepartition is metal, it needs to be coveredwith an edge protector. Care must be taken when the applianceis installed or removed, to reduce thelikelihood of damage to the power-supplycord.7.1.4 GROUNDING INSTRUCTIONSThis appliance must be grounded. In theevent of a malfunction or breakdown,grounding will reduce the risk of electricshock by providing a path of leastresistance for electric current. Thisappliance is equipped with a cord havingan equipment-grounding conductor and agrounding plug. The plug must be pluggedinto an appropriate outlet that is installedand grounded in accordance with all localcodes and ordinances. This appliancemust be connected to a grounded metal,permanent wiring system, or an equipmentgrounding conductor must be run with thecircuit conductors and connected to theequipment-grounding terminal or lead onthe appliance.WARNINGImproper connection of the equipmentgrounding conductor can result in a riskof electric shock. Check with a qualifiedelectrician or service representative ifyou are in doubt whether the appliance isproperly grounded. Do not modify the plugprovided with the appliance, if it will not fitthe outlet, have a proper outlet installed bya qualified electrician.USA
7.2 READJUSTING FOOTLEVELSNow that the dishwasher is in thecabinet you must readjust the feet tobring the dishwasher up to the requiredheight and attach it underneath thecountertop.1. Readjust the front foot levels withadjusting wrench to balance thedishwasher and raise it up under thecountertop, make sure the unit is level.2. Readjust the rear foot levels with ascrewdriver to balance the dishwasherand raise it to the required height usingthe brackets supplied.3. Attach the dishwasher underneaththe countertop with the four screwssupplied (Ø 1/8” x 1/8” - Ø 3.5mmx 14mm). Make sure you do not gothrough the top of the countertop ordamage granite.7.3 ADJUSTING THE MOVABLE TOE KICKNow that you have successfully installed the dishwasher, youneed to attach the toe kick to the dishwasher. The two piecetoe kick can be adjusted to the height and depth needed foryour kitchen. Be sure to use the slotted toe kick in the frontand the other behind it. They slide into each other.Place parts K and L to the channel shown in Figure A for bothsides as shown in Figure B. Then fix them in the directionshown with the arrow in Figure C and Figure B.15USA
Open the fixing part on the Toe Kick(p). (A)Place it on the slots, which are on the bracketsfixed before, and adjust the height (max. 40mm). (B)Close the fixing part on the Toe Kick. (C)16USA
7.4 FIXING THE CABINET TO THE COUNTERSTANDART TUB MODELS(y)TALL TUB MODELS17USA
7.5 PREPARING THE TIMBER DOORXo)X ?s) Mid. PointMid. Pointn)t)Height (h)Height (h)Width (w)Thickness (t)Weight (max)Weight (max)9 Kg / 19 lbs: Height of the wooden door 30” (760mm) Tall Tub Models Only: Height of the wooden door 28” (720mm) Standart Tub Models Only: 23 ¼” to 23 ½” (592mm - 595mm): ¾ “ (19mm): 9 Kg / 19 lbs18 USA
7.6 PREPARING THE PRODUCT DOOR(t)1219USA
7.9 INSTALLING THE TIMBER DOOR41327.10 FIXING THE TIMBER DOOR12534451 2320USA
7.11 FIXING THE TIMBER DOOR(y)Ø 4 x 36mm123451 23457.12 ADJUSTING THE KICK PLATE Check whether thebottom of the door hitsthe toe kick of the kitchencabinet (A). If the door hits the toekick cut the necessarysection out of the toe kick(B). Apply silicon or sealantto the cut edge of thekitchen cabinet toe kickor paint so it does notabsorb moisture.21USA
4 1500 1800 2000min 300min 500max 1000112211222USAmin3002min120max 10003min 500max 10007.13 CONNECTION4c3
8. INSTALLER CHECKLISTYour installer must have completed andchecked the following: The dishwasher is square and level. The dishwasher is fastened securely tothe cabinetry. The dishwasher door opens and closesfreely. The dishwasher door must closewithout hitting any cabinetry or countertop. The inlet water supply is turned on andchecked for leaks. The drain hose has been connected andchecked for leaks. There must be nokinks or obstructions in the drain hose. The drain hose must be installed with a28" (710mm) high drain loop for drainhook-ups without any air removed. If the dishwasher drain is hooked up to agarbage disposal, the drain hopper plugmust be removed. The spray arms are free and rotate freely. The rinse cycle has been run. The water level will be below thefilter screen after the end of the washprogram. It is normal to find some waterin the drain filter area.Notice : If your dishwasher is not operatingproperly after following these steps:Contact your dealer to schedule anauthorized service agent to inspect yournew dishwasher for any function relatedfailure. The manufacturer warranty does notcover installation, conversion or customereducation service visits.You will find the model and serial numberinformation on the label located on theright-hand side of the inner door of yourdishwasher, as shown above.Notice :Please make a copy of your invoice andkeep it with this manual and register yourdishwasher on-line.9. SELF HELP HINTS:The screen does not come on: Check to make sure the breaker to thedishwasher is in the on position. Check to make sure that the Supply cordis plugged.No Water is coming into the dishwasher: Check to make sure the hot water shutoff is in the ON position.Water does not drain: Make sure drain hose is not kinked orcomes out of air gap next to the sink. Remove drain hose from disposal makingsure plug is removed.15 9868 0100 AA BLOMBERG USA/ 13-02-18.(8:15)23USA
ional.com
6.5 preparing the water connection (a) 10 6.6 drain preparation 10 6.7 steam protection foil 12 7. placement of dishwasher into the opening 13 7.1 drain hose connection, water supply & electrical connections 13 7.2 readjusting foot levels 15 7.3 adjusting the movable toe kick 15 7.4 fixing the cabinet to the counter 17
