Transcription
LED Dimming DriverHi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black1% Dimming369832n 1 10.16.18Hi-lume 1% EcoSystem LED Driverwith Soft-on, Fade-to-BlackHi-lume 1% EcoSystem LED Drivers with Soft-on,Fade-to-Black provide a high‑performance solution forany space, in any application. They provide smooth,continuous dimming down to 1% of full output current,and fade smoothly between 0% and 1% with Soft-on,Fade-to-Black. 1FeaturesUL Listed Class P.UL Type TL rated. Visit “Online Certificates Directory”at www.ul.com, enter file number “E322469” todetermine the Type TL numbers specific to the LDExmodel Lutron LED Driver.Soft-on, Fade-to-Black: fades smoothly between0% and 1% when turned on and off for anincandescent‑like experience.Continuous, flicker-free dimming from 100% to 1%1.Dimming Method:– Constant-current reduction dimming providesvideo‑friendly performance down to 5%– PWM dimming below 5% (240 Hz),% Modulation 100%Guaranteed dimming performance when used withLutron EcoSystem controls.Guaranteed compatibility with Energi Savr Node unitswith EcoSystem, GRAFIK Eye QS with EcoSystem,PowPak dimming module with EcoSystem, andQuantum systems, allowing for integration into aplanned or existing EcoSystem lighting controlsolution. QwikFig compatible models available, see How toBuild a Model Number page for details. For moreinformation, please refer to the QwikFig User Guide(Lutron P/N 041473) or contact your Lutron salesrepresentative.Protected from miswires of input power to EcoSystemcontrol inputs up to 277 V .Rated lifetime of 50,000 hours at 75 C (167 F)calibration point (t c).FCC Part 15 Class A100% performance tested at factory before shipping.RoHS compliant.Case type K3.00 in (76 mm) W 1.00 in (25 mm) H 4.90 in (124 mm) LCase type M1.18 in (30 mm) W 1.00 in (25 mm) H 14.13 in (359 mm) L Non-volatile memory restores all settings afterpower failure. For more information please visit:www.lutron.com/hilume1softbled EcoSystem FeaturesSimpler to wire and more reliable than 0 –10 V-.Guarantees compatibility between Lutron controls,LED drivers, ballasts, and sensors.Accommodates zone and control changes withoutrewiring.Link to Lutron Quantum Total Light ManagementSystem to monitor lighting power consumption.Polarity-free and topology-free.Digital EcoSystem intelligence allows easy codecompliance.Digital EcoSystem control link can be Class 1 orClass 2.Light output at 1% depends on the efficacy of the LED light engine used with the driver. Job Name:Job Number:S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Page
LED Dimming DriverHi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black1% Dimming369832n 2 10.16.18Specifications Regulatory Approvals and ComplianceUL Listed Class PNOM certified for Mexico (only “BLK” models for usewith Lutron QwikFig technology)Lutron Quality Systems registered to ISO 9001.2008Manufacturing facilities employ ESD reductionpractices that comply with the requirements ofANSI/ESD S20.20Meets ANSI C62.41 category A surge protectionstandards up to and including 4 kVInrush current less than NEMA 410-2011 limitFCC Part 15 Class A Canadian EMI Class A Compliance Equivalent:CAN ICES-005(A)/NMB-005(A).Meets UL 8750, “Light Emitting Diode (LED)Equipment For Use in Lighting Products”Class 2 outputLED drivers need to meet certain performance criteriain order for the completed luminaires to comply withthe ENERGY STARR Luminaires V2.0 Specification. Allmodels meet these performance criteria throughouttheir entire load compatibility regions. ConsultApplication Note #599, “ENERGY STARR LuminairesV2.0 and Lutron Drivers,” for availability dates ofcompliant products.LED drivers need to meet certain performance criteriain order for the completed luminaires to comply withTitle 24 requirements as detailed in CEC-400-2015037-CMF. All models meet both commercial(at 120 V /277 V ) and residential (at 120 V )performance criteria throughout their entire loadoperating regions. Consult CEC-400-2015-032-CMFSection 6.2.7 for important information on meetingstart-up time requirements with fade-in lighting.M-case type performance is in compliance withDLC version 2.1 in designated areas (see “LoadCompatibility” graph in Output Range pages).PerformanceSoft-on, Fade-to-Black: fades smoothly between0% and 1% when turned on and off for anincandescent‑like experienceDimming Range: 100% to 1%1Operating Voltage: 120 V to 277 V at 50/60 HzLifetime: 50,000 hours when calibration point (t c) at75 C (167 F)2For rated warranty, t c not to exceed 75 C (167 F)(maximum rated temperature)2 Job Name:Job Number:S P E C I F I C AT I O N S U B M I T TA LModel Numbers: Patented thermal foldback protection At turn on, lighting fades smoothly to the desired levelwithout decreasing or flashing to full brightness Non-volatile memory restores all driver settings afterpower failure Typical standby power consumption: 0.2 W at 120 V and 0.3 W at 277 V Open-circuit protected output Short-circuit and overload-protected output Class 2 output designed to withstand hot swap of theLED load.Environmental Sound rated: Class A inaudible in 24 dBA ambient Relative Humidity: maximum 90% non-condensing Minimum Operating Ambient Temperature:t a 0 C (32 F)3 Indoor use only Rated for dry and damp locationsDriver Wiring and Mounting Driver is grounded by a mounting screw to thegrounded fixture or by terminal connection Terminal blocks on the driver accept one solid wire perterminal from 18 to 16 AWG (0.75 to 1.5 mm2) Fixture must be grounded in accordance with localand national electrical codes Maximum driver-to-LED light engine wire length for:Maximum Lead Length150 mA to710 mA to700 mA1.50 A18 AWG (0.75 mm2) 30 ft (9 m)15 ft (4.5 m)16 AWG (1.5 mm2) 35 ft (10.5 m) 25 ft (7.5 m)14 AWG (2.5 mm2)4 50 ft (15 m)40 ft (12 m)12 AWG (4.0 mm2)4 100 ft (30 m) 60 ft (18 m)Wire Gauge12341.51 A to2.10 A10 ft (3 m)15 ft (4.5 m)25 ft (7.5 m)40 ft (12 m)Light output at 1% depends on the efficacy of the LED light engine usedwith the driver.To maintain warranty, installer is responsible for ensuring that the drivercalibration point does not exceed 75 ºC (167 ºF).Where ta is the temperature of the air directly surrounding the driver.Terminal blocks on the drivers accept only solid 18 to 16 AWG(0.75 mm2 to 1.5 mm2) wire. To use wire gauges larger than the terminalblocks’ rated gauge of 16 AWG (1.5 mm2) refer to the Terminal WiringGauges diagram. Connect up to 3 ft (1.0 m) of 18 to 16 AWG(0.75 mm2 to 1.5 mm2) wire to the LED driver terminal blocks, thenconnect 12 or 14 AWG (4.0 mm2 or 2.5 mm2) up to the length allowed inthe above table.Page
LED Dimming DriverHi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black1% Dimming369832n 3 10.16.18How to Select the Correct LED Driver for Your Load1. Review the specifications of the LED load.2. Identify the minimum and maximum operating voltage of the LED load at the desired operating current. This“current” will be the rated output current of the LED driver. Consult the LED load manufacturer for any questions.Example: An LED load that is rated at 1 A and 33 V nominally, has an output voltage range of 28 – 38 V (at1 A) due to unit-to-unit variation, temperature, etc.3. Determine the proper operating range of the LED driver.a. Identify the output range(s) of the driver family that includes the desired current.i. Select CurrentExample: Only “B”, “C”, “U”, and “V” models meet the current range of the selected load (1 A).LED Load Output RangeL 0.15 – 0.32 A, 20–40 V-, 5-10 WJ 0.15 – 0.30 A, 30–50 V-, 6-12 WM 0.25 – 0.50 A, 20–40 V-, 6.5-14 WK 0.24 – 0.50 A, 30–50 V-, 9-20 WN 0.35 – 0.75 A, 20–40 V-, 10-20 WT 0.40 – 0.83 A, 30–50 V-, 15-35 WB 0.50 – 1.25 A, 20–40 V-, 15-35 WU 0.70 – 1.33 A, 30–50 V-, 25-50 WC 0.88 – 1.75 A, 20–40 V-, 25-50 WV 1.00 – 1.88 A, 30–50 V-, 40-75 WD 1.25 – 2.10 A, 20–40 V-, 35-75 Wii. Select VoltageExample: O ut of the 4 models indicated above, only “B” and “C” models meet the voltage requirement forthe selected load (28 – 38 V).LED Load Output RangeL 0.15 – 0.32 A, 20–40 V-, 5-10 WJ 0.15 – 0.30 A, 30–50 V-, 6-12 WM 0.25 – 0.50 A, 20–40 V-, 6.5-14 WK 0.24 – 0.50 A, 30–50 V-, 9-20 WN 0.35 – 0.75 A, 20–40 V-, 10-20 WT 0.40 – 0.83 A, 30–50 V-, 15-35 WB 0.50 – 1.25 A, 20–40 V-, 15-35 WU 0.70 – 1.33 A, 30–50 V-, 25-50 WC 0.88 – 1.75 A, 20–40 V-, 25-50 WV 1.00 – 1.88 A, 30–50 V-, 40-75 WD 1.25 – 2.10 A, 20–40 V-, 35-75 Wcontinued on next page Job Name:Job Number:S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Page
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 4 10.16.18How to Select the Correct LED Driver for Your Load (continued)b. Examine the Load Compatibility graphs below for each output range to ensure that the voltage range of theLED load is within the safe operating area.iii. Select PowerExample: L ines marked below indicate load specifications (28 – 38 V at 1 A).“B” Model (Not Compatible) “C” Model (Compatible)Since the maximum voltage of the load (38 V) exceeds theallowable voltage of “B” model (35 V at 1 A), this model isnot compatible.Load Compatibility4038 V353028 V}Operatingrange of 1 A,28 – 38 V load25201500.350.701.051.40Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 15 W outputConstant 35 W output403530{38 VOperatingrange of 1 A,28 – 38 V load28 V2520150.351.75Output Current (A)Key:Load Compatibility45Output Voltage (V)Output Voltage (V)45 Operating voltage range for “C” model is 25 – 40 V at 1 A. Sincethe load specifications are within the operating range, “C” modelis compatible for this load.0.701.051.401.752.10Output Current (A)Key:Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 25 W outputConstant 50 W output4. See How to Build A Model Number to create the appropriate model number for the desired driver. If a QwikFigcompatible driver is needed, identify the proper LED Load Output Range (voltage and current) and insert “BLK”in the Current Level (for Constant Current) section of the model number. Job Name:Job Number:S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Page
LED Dimming DriverHi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black1% Dimming369832n 5 10.16.18How to Build a Model Number, M-Case Type (“BLK” models for use with LutronQwikFig technology): Hi-lume 1% EcoSystem (up to 75 W) LED Driver with Soft-on,Fade-to-BlackM-case typeLDE1U1UMN–ALED Load Power Range(Power Range number is based onLoad Output Range category) 1: select if LED Load Output Range is “J,” “L,” or “M”2: select if LED Load Output Range is “K” or “N”3: select if LED Load Output Range is “B” or “T”5: select if LED Load Output Range is “C” or “U”7: select if LED Load Output Range is “D” or “V”LED Load Output Range: Class 2 Constant Current(see the following pages for more detail) Example: LDE13U1UMN-BA070 0.70 A 15 – 28 W** 21.5 – 40.0 V-† LED driverFor further assistance in selectingyour model number, contact ourLED Center of Excellence atLEDs@lutron.com**†At 0.7 A, maximum voltage of 40 V provides28 W (0.7 A 40.0 V 28 W)Minimum voltage of LDE13U1UMN-BA070limited by 15 W minimum power:15 W 0.70 A 21.5 VL: 0.15 – 0.32 A, 20.0 – 40.0 V- *, 5 – 10 WM: 0.25 – 0.50 A, 20.0 – 40.0 V- *, 6.5 – 14 WN: 0.35 – 0.75 A, 20.0 – 40.0 V- *, 10 – 20 WB: 0.50 – 1.25 A, 20.0 – 40.0 V-*, 15 – 35 WC: 0.88 – 1.75 A, 20.0 – 40.0 V-*, 25 – 50 WD: 1.25 – 2.10 A, 20.0 – 40.0 V-*, 35 – 75 WJ: 0.15 – 0.30 A, 30.0 – 50.0 V- *, 6 – 12 WK: 0.24 – 0.50 A, 30.0 – 50.0 V- *, 9 – 20 WT: 0.40 – 0.83 A, 30.0 – 50.0 V-*, 15 – 35 WU: 0.70 – 1.33 A, 30.0 – 50.0 V-*, 25 – 50 WV: 1.00 – 1.88 A, 30.0 – 50.0 V-*, 40 – 75 WCurrent Level (for Constant-Current) 015 0.15 AOption 1: Order a driver configured by Lutron to a desired output current.Example: LDE13U1UMN-BA070 has been pre-configured at Lutron to an output of 0.70 A. Refer to theexample above.Note: Lutron pre-configured drivers are not QwikFig compatible and cannot be re-configured. 210 2.10 AOption 2: Order a QwikFig compatible driver.Example: LDE13U1UMN-BABLK (0.5 – 1.25 A)*Note: Default set to minimum output current for the respective LED Load Output Range.Attention: Model numbers may appear similar to Lutron Hi-lume 1% EcoSystem, Hi-lume 1% 3-wire or Hi-lume 1% 2-wire drivers, but they are not directmodel-for-model replacements. Please note the driver’s output rating and the load ratings to select the correct product for your fixture.* Output voltage range changes with output current and according to power limits. Check driver specifications on the following pages carefully tounderstand output voltage range of a particular SKU. Purchaser is responsible for electrical compatibility between LED driver and LED load. Job Name:Job Number:S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Page
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 6 10.16.18M-Case Models: “L” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 20– 40 V- 0.15 – 0.32 A* 5 – 10 W75 ºC* QwikFig compatible model number LDE11U1UMN-LABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE11U1UMN-LABLK is NOM certified and available for Mexico.Typical Performance Specifications:ParameterValueTest ConditionsInput Current0.05 APower Factor0.93THD18%Driver Efficiency78%Vi 277 V , ta 25 C, Io 0.25 A, Vo 40 V-,Maximum Light OutputLDE11U1UMN-LA025Typical Efficiency vs Output CurrentLoad Compatibility80Efficiency at Pmax (%)Output Voltage put Current (A)Constant 5 W outputKey:120 V 277 V Constant 10 W outputTypical THD vs. Output PowerTypical Power Factor vs. Output Power241.00Power Factor20THD (%)0.35Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF 0Output Power (W)Key:120 V Job Name:Job Number:6789Output Power (W)277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Key:120 V 277 V Page10
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 7 10.16.18M-Case Models: “M” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 20– 40 V- 0.25 – 0.50 A* 6.5– 14 W75 ºC* QwikFig compatible model number LDE11U1UMN-MABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE11U1UMN-MABLK is NOM certified and available for Mexico.Typical Performance Specifications:ParameterValueTest ConditionsInput Current0.07 APower Factor0.95THD20%Driver Efficiency80%Vi 277 V , ta 25 C, Io 0.35 A, Vo 40 V-,Maximum Light OutputLDE11U1UMN-MA035Typical Efficiency vs Output CurrentLoad Compatibility85Efficiency at Pmax (%)Output Voltage 0Output Current (A)Constant 6.5 W outputKey:Constant 14 W outputTypical THD vs. Output Power0.450.50120 V 277 V Typical Power Factor vs. Output Power251.00Power Factor20THD (%)0.40Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF tput Power (W)Key:120 V Job Name:Job Number:8101214Output Power (W)277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:Key:120 V 277 V Page
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 8 10.16.18M-Case Models: “N” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 20– 40 V- 0.35 – 0.75 A* 10 – 20 W75 ºC* QwikFig compatible model number LDE12U1UMN-NABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE12U1UMN-NABLK is NOM certified and available for Mexico.Typical Performance Specifications:ParameterValueInput Current0.09 APower Factor0.97THD16%Driver Efficiency83%Test ConditionsVi 277 V , ta 25 C, Io 0.50 A, Vo 40 V-,Maximum Light OutputLDE12U1UMN-NA050Typical Efficiency vs Output CurrentLoad Compatibility90Efficiency at Pmax (%)Output Voltage put Current (A)Constant 10 W output0.75Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Key:0.650.55Key:120 V 277 V Constant 20 W outputTypical THD vs. Output PowerTypical Power Factor vs. Output Power251.00Power FactorTHD (%)2015100.950.900.85510121416181020Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:12141618Output Power (W)Key:120 V 277 V Page20
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 9 10.16.18M-Case Models: “B” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 20– 40 V- 0.50 – 1.25 A* 15 – 35 W75 ºC* QwikFig compatible model number LDE13U1UMN-BABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE13U1UMN-BABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.15 A0.9615%85%Test ConditionsVi 277 V , ta 25 C, Io 0.88 A, Vo 40 V-,Maximum Light OutputLDE13U1UMN-BA088Load CompatibilityTypical Efficiency vs. Output Current90Efficiency at Pmax (%)Output Voltage (V)40353025200.350.701.058580750.501.400.75Output Current (A)Key:Key:Typical THD vs. Output Power120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor25THD (%)1.25Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 15 W outputConstant 35 W output2015101.00152025300.950.900.85351520Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:2530Output Power (W)Key:120 V 277 V Page35
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 10 10.16.18M-Case Models: “C” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 20– 40 V- 0.88 – 1.75 A* 25 – 50 W75 ºC* QwikFig compatible model number LDE15U1UMN-CABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE15U1UMN-CABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.21 A0.9713%88%Test ConditionsVi 277 V , ta 25 C, Io 1.25 A, Vo 40 V-,Maximum Light OutputLDE15U1UMN-CA125Load CompatibilityTypical Efficiency vs. Output Current90Efficiency at Pmax (%)Output Voltage (V)40353025200.701.051.408580750.851.751.15Output Current (A)Key:Key:Typical THD vs. Output Power120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor20THD (%)1.75Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 25 W outputConstant 50 W output151051.4525303540450.950.900.85502530Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:354045Output Power (W)Key:120 V 277 V Page50
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 11 10.16.18M-Case Models: “D” Output RangeDriver TypeOutputVoltageOutputCurrentOutputPowerConstant Current Driver (Class 2) 20– 40 V- 1.25 – 2.10 A*StandardsRecognitionMaximum Rated Temp.@ tc for WarrantyN**35 – 75 W75 ºC* QwikFig compatible model number LDE17U1UMN-DABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE17U1UMN-DABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.31 A0.9513%89%Test ConditionsVi 277 V , ta 25 C, Io 1.88 A, Vo 40 V-,Maximum Light OutputLDE17U1UMN-DA188Load CompatibilityTypical Efficiency vs. Output Current90Efficiency at Pmax (%)Output Voltage (V)40353025201.051.401.758580751.252.101.50Output Current (A)Key:Key:Typical THD vs. Output Power120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor20THD (%)2.00Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 35 W outputConstant 75 W 5Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:5055606570Output Power (W)Key:120 V 277 V Page75
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 12 10.16.18M-Case Models: “J” Output RangeDriver TypeOutputVoltageOutputCurrentConstant Current Driver (Class 2) 30– 50 V- 0.15 – 0.30 A*OutputPowerStandardsRecognitionMaximum Rated Temp.@ tc for WarrantyN**6 – 12 W75 ºC* QwikFig compatible model number LDE11U1UMN-JABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE11U1UMN-JABLK is NOM certified and available for Mexico.Typical Performance Specifications:ParameterValueInput Current0.06 APower Factor0.93THD19%Driver Efficiency79%Test ConditionsVi 277 V , ta 25 C, Io 0.24 A, Vo 50 V-,Maximum Light OutputLDE11U1UMN-JA024Typical Efficiency vs Output CurrentLoad Compatibility85Efficiency at Pmax (%)Output Voltage (V)50454035308075700.150.200.250.300.15Output Current (A)Constant 6 W output0.30Key:120 V 277 V Constant 12 W outputTypical THD vs. Output PowerTypical Power Factor vs. Output Power251.00Power Factor20THD (%)0.25Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF ut Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:81012Output Power (W)Key:120 V 277 V Page
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 13 10.16.18M-Case Models: “K” Output RangeDriver TypeOutputVoltageOutputCurrentConstant Current Driver (Class 2) 30– 50 V- 0.24– 0.50 A*OutputPowerStandardsRecognitionN**9– 20 WMaximum Rated Temp.@ tc for Warranty75 ºC* QwikFig compatible model number LDE12U1UMN-KABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE12U1UMN-KABLK is NOM certified and available for Mexico.Typical Performance Specifications:ParameterValueInput Current0.09 APower Factor0.96THD18%Driver Efficiency84%Vi 277 V , ta 25 C, Io 0.40 A, Vo 50 V-,Maximum Light OutputLDE12U1UMN-KA040Typical Efficiency vs Output CurrentLoad Compatibility5090Efficiency at Pmax (%)Output Voltage (V)Test Conditions454035308580750.200.300.400.200.50Output Current (A)Constant 9 W output0.50Key:120 V 277 V Constant 20 W outputTypical THD vs. Output PowerTypical Power Factor vs. Output Power251.00Power Factor20THD (%)0.40Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF put Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:121620Output Power (W)Key:120 V 277 V Page
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 14 10.16.18M-Case Models: “T” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 30– 50 V- 0.40 – 0.83 A* 15 – 35 W75 ºC* QwikFig compatible model number LDE13U1UMN-TABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE13U1UMN-TABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.15 A0.9613%87%Test ConditionsVi 277 V , ta 25 C, Io 0.70 A, Vo 50 V-,Maximum Light OutputLDE13U1UMN-TA070Load CompatibilityTypical Efficiency vs. Output Current90Efficiency at Pmax (%)Output Voltage (V)50454035300.250.500.758580750.401.000.50Output Current (A)Key:Key:Typical THD vs. Output Power0.80120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor20THD (%)0.70Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 15 W outputConstant 35 W output151050.60152025300.950.900.85351520Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:2530Output Power (W)Key:120 V 277 V Page35
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 15 10.16.18M-Case Models: “U” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 30– 50 V- 0.70 – 1.33 A* 25 – 50 W75 ºC* QwikFig compatible model number LDE15U1UMN-UABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE15U1UMN-UABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.21 A0.9711%86%Test ConditionsVi 277 V , ta 25 C, Io 1.0 A, Vo 50 V-,Maximum Light OutputLDE15U1UMN-UA100Load CompatibilityTypical Efficiency vs. Output Current90Efficiency at Pmax (%)Output Voltage put Current (A)Key:Key:Typical THD vs. Output Power1.101.201.30120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor20THD (%)1.00Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 25 W outputConstant 50 W output151050.9025303540450.950.900.85502530Output Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:354045Output Power (W)Key:120 V 277 V Page50
Hi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-BlackLED Dimming Driver1% Dimming369832n 16 10.16.18M-Case Models: “V” Output RangeDriver RecognitionMaximum Rated Temp.@ tc for WarrantyN**Constant Current Driver (Class 2) 30– 50 V- 1.00 – 1.88 A* 40 – 75 W75 ºC* QwikFig compatible model number LDE17U1UMN-VABLK is configurable to any current within this range in 0.01 A increments.** BLK model LDE17U1UMN-VABLK is NOM certified and available for Mexico.Typical Performance SpecificationsParameterInput CurrentPower FactorTHDDriver EfficiencyValue0.31 A0.9613%90%Test ConditionsVi 277 V , ta 25 C, Io 1.5 A, Vo 50 V-,Maximum Light OutputLDE17U1UMN-VA150Load CompatibilityTypical Efficiency vs. Output Current95Efficiency at Pmax (%)Output Voltage put Current (A)Key:Key:Typical THD vs. Output Power120 V 277 V Typical Power Factor vs. Output Power1.00Power Factor20THD (%)1.75Output Current (A)Shaded area meets DLC Version 2.1 (areas outside ofshaded areas may not meet THD or PF requirements).Constant 40 W outputConstant 75 W put Power (W)Key:120 V Job Name:Job Number:277 V S P E C I F I C AT I O N S U B M I T TA LModel Numbers:5055606570Output Power (W)Key:120 V 277 V Page75
LED Dimming DriverHi-lume 1% EcoSystem LED Driver with Soft-on, Fade-to-Black1% Dimming369832n 17 10.16.18How to Build a Model Number, K-Case Type (“BLK” models for use with LutronQwikFig technology): Hi-lume 1% EcoSystem (up to 40 W) LED Driver with Soft-on,Fade-to-BlackK-case typeLDE14U1UK–ACase Style S: Studded (K-case only) N: Non-Studded LED Load Output Range: Class 2 Constant Current(see the following pages for more detail)A: 0.22 – 0.45 A, 21.0 – 50.0 V-*, 7 – 17.5 WB: 0.33 – 0.70 A, 30.0 – 50.0 V-*, 14 – 35 WC: 0.46 – 0.93 A, 16.0 – 37.1 V-*, 13 – 26 WD: 0.38 – 0.75 A, 12.0 – 30.2 V-*, 8 – 16 WE: 0.71 – 1.05 A, 31.0 – 50.0 V-*, 22 – 40 WF: 0.71 – 1.40 A, 19.0 – 38.0 V-*, 21 – 40 WG: 0.94 – 1.40 A, 13.0 – 30.0 V-*, 18.5 – 32 WH: 0.63 – 1.05 A, 10.0 – 21.0 V-*, 8 – 18 WExample: LDE14U1UKN-BA070 0.70 A 21 – 35 W** Non-studded case LED driverFor further assistance in selectingyour model number, contact ourLED Center of Excellence atLEDs@lutron.com** Minimum and maximum wattages derivedfrom minimum and maximum compatibleload voltages at 0.7 A:0.7 A 30 V 21 W; 0.7 A 50 V 35 WCurrent Level (for Constant-Current) 022 0.22 AOption 1: Order a driver configured by Lutron to a desired output current.Example: LDE14U1UKN-BA070 has been pre-configured at Lutron to an output of 0.70 A.Refer to the example above.Note: Lutron pre-configured drivers are not QwikFig compatible and cannot be re-configured.Option 2: Order a QwikFig compatible driver.Example: LDE14U1UKN-BABLK (0.33 – 0.70 A)*Note: Default set to minimum output current for the respective LED Load Output Range. 140 1.40 AAttention: Model numbers may appear similar to Lutron Hi-lume 1% EcoSystem, Hi-lume 1% 3-wire or Hi-lume 1% 2-wire drivers, but they are not directmodel-for-model replacements. Please note the driver’s output rating and the load ratings to select the correct product for your fixture.* Output voltage range changes with output current and according to power limits. Check driver specifications on the following pages carefully tounderstand output voltage range of a particular SKU. Purchaser is responsible f
Quantum systems, allowing for integration into a planned or existing EcoSystem lighting control solution. QwikFig compatible models available, see How to Build a Model Number page for details. For more information, please refer to the QwikFig User Guide (Lutron P/N 041473) or contact your Lutron sales representative.
