Transcription
BITMAINAPW3-12-1600 PSU SeriesUser Guide
AntMiner PSUAPW3-12-1600 SeriesContents1234567Overview . 3Features. 3Specifications . 4Switching On/Off Remotely. 5Order Information & Wire Type . 65.1Order Information . 65.2Wire Types . 6Trouble Shooting & FAQ . 7Precautions for Use . 8May 14, 2015 Version 1.1Page 2 / 8
AntMiner PSUAPW3-12-1600 Series1 OverviewThe APW3-12-1600 series AC-DC PSU combines high efficiency and good dynamic performanceinto a power dense package. It also features overload, overheat, overcurrent and low voltageprotection, making it well suited to 12V, 1600W power devices.Please note:1. This PSU cannot be used in countries with a mains power voltage is lower than 205V, the PSUwill not start below this voltage.2 Features 20% voltage input rangeHigh efficiency, up to 93.8%Short circuit, overload and overheat protectionExtreme power density, 1U form factor100% rated up to 50 C ambientC13 power connector12 Month WarrantyMay 14, 2015 Version 1.1Page 3 / 8
AntMiner PSUAPW3-12-1600 Series3 itionsStructureCoolingDC Voltage12VRated Current133ARated Power1600WRipple & Noise 1%Voltage Regulation 2%Source Regulation 1%Load Regulation 1%Setup, Rise Time 5SPower off Protection Trip Time 10mSInterface Type12 pairs of 6 pin PCI-E connectors. 450mmlength for each PCI-E cable.Voltage Range176-264V ACStarting Voltage200-205V ACFrequency Range47-63HzPower Factor 0.95 (full load)Leakage Current 1.5mA (220V 50Hz)Interface TypeIEC320-C13Low-voltage Input171-181V ACOutput Short CircuitYesOutput Overcurrent134-150AOverheat ProtectionYesOperating Temperature-20-50 ºC @ 100%,-20-60 ºC @ 80% load (refer toLoad/Temperature graph)Operating Humidity20% - 90% RH kgFan Size40mm*40mm*28mmAir Blowing DirectionFrom AC input to DC outputMay 14, 2015 Version 1.1Page 4 / 8
AntMiner PSUAPW3-12-1600 SeriesMax Load vs. Ambient Temperature Graph (220V input)Max Load vs Input 25120117115110107105100Temperature( )-20020505560Efficiency vs Load (220V %Efficiency89.0%88.0%87.0%Load(A)86.0%0501004 Switching On/Off RemotelyThe PSU turns on automatically by plugging it into the mains. However, it also has a 3-pin portwhich can be used to remotely power the PSU on and off.Remote On/Off Method 1: Use the physical power switch to control ON/OFF and GND lines,May 14, 2015 Version 1.1Page 5 / 8
AntMiner PSUAPW3-12-1600 Seriesclosing the circuit turns the machine on, and breaking the circuit turns the machine off.Remote On/Off Method 2: 5V sb PSU supports an external MCU, which controls a transistoror MOSFET to manage the ON/OFF pins to switch the PSU ON/OFF remotely. The PSU willturn on once power is provided to the 5V sb pin.5 Order Information & Wire Type5.1 Order InformationAPW3-12-1600-B2PSU Wire TypeRevisionRated Power (W)Voltage Output (V)PSU Model #5.2 Wire TypesType 1:4 pairs of M4roundterminalconnectors and 1PCI-E6pinconnectorType 2:12 pairs of 6 pinPCI-E connectors.450mm length foreach PCI-E.May 14, 2015 Version 1.1Page 6 / 8
AntMiner PSUAPW3-12-1600 Series6 Trouble Shooting & FAQ#IssueReason1Fan won’t run, and no12V outputAC Input is abnormal1. Make sure the AC input wire has a goodconnection and the plugs areconnected firmly2. Make sure the mains power is workingwell and its voltage is above 205V.2The fan is running, butthere is no 12V output.1. Voltageinyourpower system islower than required2. PSU is in protectionmode1.3After a few minutes,the PSU stops working,starts working, stopsworking and keepscycling.PSU is inprotection1． Check whether the fan is working2． Check whether the fan’s vent is beingblocked4Output is normal, butthe fan is not working.Fan is broken1. Check that the fan is clear of blockagesor buildup2. Fan is broken and needs to be replaced.5The PSU suddenly hasno output and can’t bestarted again.ThePSUisinover-current protection.Check whether the load current heprotectionautomatically triggers when the loadcurrent exceeds the limit to protect againstdamage to the PSU and the miner.over-heatTroubleshootingPlease check whether the voltage isabove 205V with multimeter to makesure the PSU can switch on correctly.2. Check whether there is a short circuitoutput or overload that is causing thePSU to enter a locked status. Afterremoving the problem, the PSU shouldpower up.3． Check whether there is a dust buildupinside the PSU due to prolonged use.Do NOT remove the PSU’s cover unlesstrained to do so.4． Check the power and ambienttemperatures follows theLoad/Temperature graphMay 14, 2015 Version 1.1Page 7 / 8
AntMiner PSUAPW3-12-1600 Series7 Precautions for Use1. Before using the PSU, please ensure that the voltage and power outputs are compatiblewith your equipment.2. Please ensure that the PSU appears to be in good shape and has not suffered damage intransit. If the exterior of the PSU appears damaged, do not use it.3. Make sure that the metal cover for the PSU with on/off switch is properly grounded.Improper grounding is dangerous.4. The PSU must be installed in such a way that it receives good, unobstructed airflow.Under no circumstances should the PSU be installed in an enclosed place.5. When installing the PSU, please double check that the output polarities are the correctway round, and that the screws are fastened securely in place.6. Do not attempt maintenance on any wiring while the PSU is powered up from the mains.7. Running the PSU at 80% load or below can greatly prolong the life of the PSU. Usually,for every 10ºC above the rated amount, the life of the PSU is cut in half.May 14, 2015 Version 1.1Page 8 / 8
2. PSU is in protection mode 1. Please check whether the voltage is above 205V with multimeter to make sure the PSU can switch on correctly. 2. Check whether there is a short circuit output or overload that is causing the PSU to enter a locked status. After removing the problem, the
