Transcription
Operating ManualFor Easy ClickerUR3-SR3Universal Remote Control, Inc.www.universalremote.comOCE-0009D REV 38
1 IntroductionThis remote control is designed to operatemost Digital and Analog Cable Boxes, as wellas TVs, and a DVD player.2 Replacing BatteriesBefore you program or operate the remotecontrol, you must install two new AAA alkalinebatteries.STEP1 Remove the battery compartment coverfrom the back of your remote control.STEP2 Check battery polarity carefully, andinstall the batteries as shown in theillustration below.STEP3 Replace the battery compartment cover.Install twoAAA alkaline batteriesas shown here1
3 Button Functions4 Programming the Remote Control.*Note : In this section, when you are instructed topress a [DEVICE] button, that means youshould press either the CBL, TV, or DVDbutton, depending on which device you areprogramming the remote to operate.A. Quick Set-Up MethodSTEP1 Turn on the component you want toprogram. To program your TV, turn on the TV.2
STEP2 Press and hold the [DEVICE] key for 5seconds until the Device LED will blinkonce and stays on. Continue to hold the[DEVICE] key and press the number keyassigned to your brand in the Quick Setup Code Table and release both [DEVICE]key and the number key to save thecode. The Device LED will blink twice toconfirm that the code is stored.STEP3 Point the remote control at thecomponent.STEP4 Press the [DEVICE] button. If it turns off,it is programmed for your component. If itdoes not turn off, use the PreProgrammed 3-Digit code Method orScanning Method.Repeat the steps above for all components (CBL,TV, DVD).B. Quick Set-up Code TablesCBLQuick Number0123456789Manufacturer/BrandPACE DTASA/CISCO, SAMSUNG, PACE DIGITALMOTOROLA DIGITALMOTOROLA DTAEVOLUTION DTACISCO IPTVADB IPTVTECHNICOLORAMINO 140/540 IPTVMOTOROLA IPTV3
TVManufacturer/BrandQuick PHILIPSHITACHISHARPVIZIODVDQuick PSSAMSUNGPHILIPS MAGNAVOXPANASONICLGJVCDENONPIONEERC. Manual ProgrammingThe remote control can be programmed by enteringa three-digit code number that corresponds toparticular brands and models of equipment. Thethree-digit code numbers are listed in the codetables sections of this instruction manual.STEP1 Turn on the equipment that you want theremote control to operate Cable Box, TVand DVD.STEP2 Press the [DEVICE] button and the4
[OK/SEL] button simultaneously for threeseconds. The corresponding device LEDwill turn on indicating that it is ready to beprogrammed. The LED will remain on for20 seconds. The next step must beentered while the LED is on.STEP3 Point the remote control toward theequipment and enter the three-digit codenumber assigned to your brand from thecode tables. If there are more than onethree-digit number listed for your brand,try one code number at a time until yourequipment turns off.*Note : You can verify that you have selected thecorrect code by pressing the [MUTE]button. The equipment should turn on oroff.STEP4 Store the three-digit code by pressing thesame [DEVICE] button once again. Thedevice LED will blink twice to confirm thatthe code has been stored.*Note : Try all the functions on the remotecontrol. If any of the functions do notoperate as they should, repeat theinstructions from Step 2 using the nextthree-digit code number from the samebrand list.D. Auto Search MethodIf none of the three digit code numbers assigned toyour brand of equipment works, or the code tabledoes not list your brand, you can use the AutoSearch Method to find the correct three-digit codenumber for your equipment by following steps:5
STEP1 Turn on the equipment that you want theremote control to operate (Cable Box, TV,or DVD).STEP2 Press the [DEVICE] button and the[OK/SEL] button simultaneously for threeseconds. The device LED will turn onindicating that it is ready to beprogrammed. The LED will remain on for20 seconds. The next step must beentered while the LED is on.STEP3 Press the [CH5] or [CH6] button one at atime or keep it pressed. The remote willemit a series of Power ON/OFF codesignals. Release the [CH5] or [CH6]button as soon as the equipment turns off.*Note : You can verify that you selected thecorrect code by pressing the [MUTE]button. The equipment should turn On orOff.STEP4 Press the same [DEVICE] button to storethe code. The Device LED will blink twiceto confirm that the code has been stored.E. To find the Three-Digit Code that WasProgrammed using the Auto Search MethodSTEP1 Press the appropriate [DEVICE] buttonand the [OK/SEL] button simultaneouslyfor three seconds. The device LED willturn on for 20 seconds. The next stepmust be performed while the LED is on.STEP2 Press the [INFO] button. The device LEDwill blink a number of times indicating thenumber of each digit for the code. Eachdigit is separated by a one second6
interval of the LED being off.Example : One blink, then three blinks, then eightblinks indicates the code number 138.*Note : Ten blinks indicates the number 0.F. Programming a Second TV to the DVD ButtonSTEP1 Press the [DVD] button and the [OK/SEL]button simultaneously for 3 seconds. TheDVD LED will turn on for 20 seconds. Thenext step must be performed while theLED is on.STEP2 Press the [TV] button.STEP3 Point the remote control toward the TV andenter the three-digit code for your TV fromthe TV codes table.STEP4 Store the three-digit code by pressing the[DVD] button. The device LED will blinktwice to confirm that the code has beenstored.G. Programming for Advanced Functions.In the CABLE device mode, the A,B,C,D and blankmacro buttons can be programmed to act as a'Macro' or Favorite Channel button. This allowsyou to program up to five 2-digit channels, four 3digit channels or three 4-digit channels that canbe accessed with ONE button press.*Note : The A,B,C and D buttons are notprogrammable if you have a DigitalCable Box made by Pace, Pioneer orScientific-Atlanta.STEP1 Press the [CBL] button to select the CBLmode.7
STEP2 Press the [MACRO] button and [OK/SEL]button simultaneously for 3 seconds. The[CBL] button will turn on for 20 seconds.STEP3 Enter the 2, 3 or 4-digit code for thechannel you want programmed first (forexample, 007) using the Number Pad,then press the [STOP] button. Then enterthe code for the next channel (forexample, 050), then press the [STOP]button. Repeat this process for the thirdchannel. The [CBL] button will blink oncefor each channel entered.STEP4 Press the [CH5] button to store thechannels that were selected. The [CBL]button will blink twice to confirm thestorage of commands.To access the programmed channels, pressthe [MACRO] button once. This will bring upthe first channel. Press once again and itwill bring up the second channel. Pressagain and it will bring up the third channel.To erase the Macro programming and return tothe original function:STEP1 Press the [CBL] button to select theCABLE mode.STEP2 Press a [MACRO] button and the[OK/SEL] button simultaneously for 3seconds. The CBL device LED will turn onfor 20 seconds. The next step must beperformed while the LED is on.STEP3 Press the [CH5] button to erase thefunctions stored in the button. The CBL8
device LED will blink twice to confirm thatthe memory button has been erased.H. Assigning the Volume and Mute keysto a Different DeviceBy default, the VOL5, VOL6 and MUTE keysoperate through your TV. If you would like thosekeys to operate those functions on a differentdevice, follow these steps.STEP1 Press the [OK/SEL] button and [CBL]button simultaneously for three seconds.The device LED will turn on for 20seconds. The next step must beperformed while the LED is on.STEP2 Press the [VOL 5] button. The deviceLED will blink.STEP3 Press the [DEVICE] button correspondingto the device that you would like thevolume and mute buttons to control. Thedevice LED will blink twice to confirm theprogramming.Example : If you wish to have the volume andmute keys operate your Cable Box,press the [CBL] button in Step3.I. Assigning the Channel keys to aDifferent DeviceBy default, the CH5, CH6, NUMERIC and LAST keysoperate through your Cable Box. If you would likethose keys to operate those functions on a differentdevice, follow these steps.STEP1 Press the [OK/SEL] button and [CBL]button simultaneously for three seconds.The device LED will turn on for 209
seconds. The next step must beperformed while the LED is on.STEP2 Press the [VOL 6] button. The device LEDwill blink.STEP3 Press the [TV] button. The device LEDwill blink twice to confirm theprogramming.*Note : If you wish to have the channel keysoperate your Cable Box, press the [CBL]button instead of the [TV] button in Step 3.J. Assigning the DV D - V OD keys tocontrol your DVDBy default, the REW, Play, FF, Record, Stop andPause keys operate VOD (Video On Demand)through your Cable Box. If you would like thosekeys to operate those functions on your DVD,press the PLAY button for 3 seconds until the DVDbutton lights. To return to your Cable Box control,press the PLAY key again for 3 seconds until theCBL button lights.K. Low Battery WarningWhen the battery is low (2.3V-2.0V) and needs to bereplaced with fresh batteries, device LED will blink 2times in sequence whenever a [DEVICE] button ispressed to turn on equipment.L. Memory Lock System.This remote control is designed to retainprogrammed memory for 10 years — even afterbatteries are removed from the remote control.For additional information about your remotecontrol, go to www.universalremote.com10
5 Set up Code TablesCABLE TVCONVERTERMAKER(BRAND) NAMECISCO/SAEXPLORER Series8600X86008540,8570,85908500IPN SeriesLogicTVMOTOROLADCT Series (DVR Model)VIP SeriesDTA100GENERAL INSTRUMENT DCT Series,DCH Series, XSome ModelDL4,DQNV/DRX,DPBB,DPV/DP/DQN,DRZADBADB SeriesADB5810WXADB5810W, ADB5721WNXAMINOAmiNET SeriesA125, A130, A530A110A140, A540, A550ARRISMP2000FrontierAT&TU-VERSEBELL FIBEPVR SlimCINCINNATI BELLZTEZTE B700-V3CISCORNG200IPN SeriesCIS330, CIS430DIGITAL TRANSPORT ADAPTER50COMCASTRNG200XFINITYCONFLUENTCTG4-HDRCox Digital CableMini BoxDIGEO2056-MSXDigital Multimedia Technology DMT-205HDDirecTVGenieSky AP HD / Sky Ap JrDREAMDM7020SDSTVDSTV [PVR1]DSTV [PVR2]11CODE No001 5002048027054 055115163249256 257260 3222238239159182183
CABLE TVCONVERTERMAKER(BRAND) NAMEDUNEDuosonENTONEEVOLUTION FTAEVOLUTIONFoxtelHAMLINHOMECASTHorizonInnovative IONNOW TVNSCOAKPACEPANASONICPico DigitalPIONEERSMART B1,BE,D1,H1,HE,MEMINI,ULTRATotalPlayURC PLUSKamai 651Kamai 500Kamai 45xX0-01UNIVERSAL SD DTAUNIVERSAL HD PTV ReceiverMiniC12516MOXI MEDIA CENTERMOXI HD DVR2056-MSXEvo SeriesDCI-4136MHDDTAADB-5720SXABD5720SXNUVENIO SD PHOENIX, NUVENIO HD,SOLARIS, NOVANOWTVIM781RIM781SIGMAONE, P1,P2,P3, SIGMA 2000RTC56,RKDMSIGMA 2001,2002SIGMA 450,500,550500 SeriesTDC SeriesDTA 0,130,150,160VMX1VOYAGER Series12CODE No184185218155221210 2153054 055211201181186192114046047037038039040001 007002113004214206217030031224001 007
CABLE TVCONVERTERMAKER(BRAND) NAMECODE NoBA9000BA4100,4200,4500BA-V1000ALL MODELSOCAP NETTHOMPSONTILEVISIONTOCOMTRANSPARENT VIDEO 1 007130ANALOG CONVERTER190HD TCM191SKY HD230SKY HD204Q240AP HD, AP EM1,DCI104ICS 365 188TV1918755070355503A0364000A193SMD E-DVR(TIVO)MAKER(BRAND) NAMECHANNEL MASTERDSTVHUGHESHUMAXICREALTIMEPHILIPSSpeco TechnologiesTIVOTOSHIBAZUUMMEDIACODE NUMBER (3 DIGIT) LIST859836 837 838 839 840817 821 822 823 824 825 826 827 828817 818834 816790 817 821 822 823 824 825 826 827 828 835879790 817 818 821 822 823 824 825 826 827 828 858817855TVMAKER(BRAND) NAMEADMIRALAD NOTAMADVENTAFFINITYAIWAAKAICODE NUMBER (3 DIGIT) LIST072 081 160 161 096672147680141 145070 146 004 148 124 226 104 108 24413
TVMAKER(BRAND) NAMEAKIOALARONAMARKAMERICA ACTIONAMPROANAMAOCAPEXAPEX RAIGCROSLEYCROWNCURTIS MATHESCXCDAEWOODAYTRONDELLDENONDIGITAL PROJECTIONCODE NUMBER (3 DIGIT) LIST103028112 127043073 167043 054 056 080 112 131058 070 004 112 245092015 150 037 724097 100 686076 103 043 035 078 224689090 628223761711043072234043096 170162070 002 003 004058164001043714732103 120070 002 003 004 101 103 127043640 641 671 236004043 051161 746 747127043 054 028164043 127070 004 101 011 072 081 120 164 127043076 103 112 004 127 016 043 044 125 120004 127041 24901109014
TVMAKER(BRAND) NAMECODE NUMBER (3 DIGIT) TROHOMEELEMENTEMERSON004 073131 132 161043062007 057001024 076 127004 110 622 690005 028 043 048 076 096 155 004 051 151 153154 127 121ENVISION070EPSON087 228ESA031Evervue755FREEMOTION688FUJITSU164 197 028 157 149 066 217FUNAI028 043 052 168FUSION642FUTURETECH043GATEWAY165 031GE070 073 130 144 160 161 004 008 009 034 056074 091 155 081 120GEM031GIBRALTER004 073GOLDSTAR004 106 112 127GPX674GRUNPY028 043HAIER004 116 623 236 749HALL MARK004HANNSPREE099HARLEY DAVIDSON 028HARMAN KARDON 164HARVARD043HISENSE198 021 619 630 631 236 752HITACHI011 007 009 004 072 010 012 023 075 158 127174 243 670 749HP027 039 098HUMAX122HYPERION242HYUNDAI049 067ILO055 096INFINITY164INFOCUS046 215 225 233 726 733INKEL129INSIGNIA068 069 078 096 164 168 247INTEQ073JBL16415
TVMAKER(BRAND) IAONKINGONWACODE NUMBER (3 DIGIT) LIST001004 008 024 030 065 070 101 160 156 127013038 001 034 083 195 159 227 639070 001220002 059202070 043 154 127004 106 112 127 086 236 648 741072196 164 738072004007 015 052 081 160 164070 003 004 022 059 060 061 063 064 127 164094 160 056 028 035 211 205 218 050 138 232072164 070 143 169164080165004004 007 072 028 096088024 070 004 042073088077008109 024 042 004 040 146 028 124 081 200 235081070 004 062 101043015 025070 130 134 040 056 007 019 024 004 182 140717 758620 078043103175211103084219 004 161 144 16004304316
TVMAKER(BRAND) NAMECODE NUMBER (3 DIGIT) PHILCOPHILIPS080029 032019 081096 201 203 204 205 028080 034 056 164 190 230 248 237 240 664723 763070 003 004 024 056 059 060 063 064 127 164164 005 038 093 127 070 003 004 059 199 218161 232 629 727 773PIONEER023 025 135 176 004 018 070 183 191 208 214 182 660PLANAR728 742 787 788POLAROID026 118 119 006 110PORTLAND004 103 127PRISM034PROSCAN144 160 161 167 236PROTON004 058 171 173 193 127 163PROTRON102 213 004 115PROVIEW110PROX092PYLE HOME661 662QUASAR034 056 239RADIO SHACK004 019 127 043RCA160 161 144 156 065 070 004 023 024 056 074152 081 209 713 751REALISTIC007 019REVOLUTION HD 220RUNCO072 073 130 179 180 181 182 216 194 697SAMPO070 004 058 165SAMSUNG192 089 004 101 127 133 160 105 070 184 185 515 655SANSEI120SANSUI096 244 078 762SANYO007 053 057 082 020 750SCEPTRE036 699SCOTCH004SCOTT004 005 028 043 048 127 113SEARS004 007 015 028 030 057 082 094 160 052 164 081 019 014 028 004 022 127 684 692 735 765 766SHERWOOD128SIGNATURE072Silo001Skyvue086SOLE177 17817
TVMAKER(BRAND) EWSSSSTARLITESUNBRITESUPRE MACYSUPREMESVASYLVANIASYMPHONICSYNTAX OLEVIATANDYTATUNGTCLTECHNICSTECHNOL VERSALUPSTARVENTURERVIDEO DSW Box TechnologiesWESTINGHOUSEWINBOOKYAMAHACODE NUMBER (3 DIGIT) LIST001 241 633 126 139003 004 028 043163112004052004 043043633 634 635 236 238 772002001046070 003 059 060 063 064 127 160 164 044 056168 121 231052 168219 004 161 144 160081056 062705 749034 080028246004002 003 004 024 028 043 072 101 103 164 127244072172166663004073015 030 007 040 062 101 142 045 137 703127212008 009708236146188 164 182004210 211 720055 229 192110236 031 624 004 625 675004 064 164 008 009 019 028 060 061 063 072074 070 127731076 036 221 222 001 280 690 695079004 070 206 20718
TVMAKER(BRAND) NAMEYORKYUPITERUZENITHZONDACODE NUMBER (3 DIGIT) LIST004043011 072 073 095 103 096112DVDMAKER(BRAND) NAMECODE NUMBER (3 DIGIT) LISTADCOM203AIWA210 214AKAI239ALPINE179ANTHEM361APEX DIGITAL240 197 247 248 196ARCAM165 148 374AUDIOVOX075BOSE244 245CAMBRIDGE AUDIO 224 145 360CARY AUDIO DESIGN 249 149CLASSE242COBY206CYBERHOME170 212DAEWOO170DENON226 184 225 I235GE188 189GOLDSTAR182 194GO VIDEO228 182 252 253 254GRADIENTE243HARMAN KARDON 217HITACHI181HITEKER197INSIGNIA078 235 085 182 178 089 385INTEGRA208 236 238 128JVC185KENWOOD166KISS237KLH230KOSS243KRELL21819
DVDMAKER(BRAND) RY YLVANIASYMPHONICTAG McLarenTASCAMTECHNICSTHETA DIGITALCODE NUMBER (3 DIGIT) LIST216182 194 105 090150178 191 195 235 386176 177 135167222200240 196229186112211198 182 092207 236 128125187243076 219 173 184 192 103 104 379083164 074 209 176 177 191 195 127 381187 180 175 221 223 093 364 156 377075 084 085250 251172188 189188 189 086201215183 228 193 205 073 152 241 380254 255174083 129 361077 190 213 168 118 119 120 121 126 091 363 368378 38208823523523523520218517318720
DVDMAKER(BRAND) E NUMBER (3 DIGIT) LIST169 171 191 206 227 201 236 356151229220 087375199 204 246 184 192 334 383182 194*Note : For TV/DVD combination units, Pleaseuse following steps to operate the volumecontrol.STEP1 Press the [CBL] button and the [OK/SEL]button simultaneously for 3 seconds. Thedevice LED will turn on for 20 seconds.The next step must be performed whilethe LED is on.STEP2 Press the [VOL5] button.STEP3 Press the [DVD] button. The CBL deviceLED will blink twice to confirm theprogramming.21
For Easy Clicker OCE-0009D REV 38. 1 This remote control is designed to operate most Digital and Analog Cable Boxes, as well as TVs, and a DVD player. . AT&T U-VERSE 051 BELL FIBE PVR
