Security Mesh And Secura Clips The Behind The Drywall .

Transcription

SUBMITTALTRANSMITTALSUBMITTALDETAILSAMICO09 29 10ALABAMA METAL INDUSTRIES CORPORATIONSecurity Mesh and Secura Clipsthe behind the drywall penetration barrierProject Submittals as manufactured byALABAMA METAL INDUSTRIES CORPORATIONSubmittal Date:Contract Number:Refer to ASTM C1063 for support spacing, lath selection, fastener selection and further information regarding the proper installation of metal lath.Project Name:Section Number:ASTM and most codes require hot dipped galvanizedlath for all exterior applications.Contractor’s Name:Meets Buy American Procurement Requirements.Made in the United States of America09 29 10Refer to ASTM C1063 for support spacing, lath selection, fastener selection and further information regarding the proper installation of metal lath.ASTM and most codes require hot dipped galvanizedlath for all exterior applications.Meets Buy American Procurement Requirements.Made in the United States of AmericaAll information contained herein is accurate as known at the time of publication. Specifications may change and AMICOreserves the right to change product specifications without notice and without incurring obligations.ALABAMA METAL INDUSTRIES CORPORATION3245 Fayette Avenue Birmingham, AL 35208 Telephone 800/366-2642 Facsimile 205/786-6527email fmayer@gibraltar1.com

SECURITY MESH by AMICOThe following is a short list of retail companies that specify and depend onTHE SECURITY MESH SYSTEM as a penetration barrier in partition walls.The AMICO System is used to secure people and property from unwanted 7.18.19.20.Amsouth BankAT&TBabies R UsBank of AmericaBank OneBank of TexasBarnes & NobleBed Bath & BeyondBest BuyBorder BooksCartierChase Manhattan BankCompass BankCVS Pharmacy & WarehouseFederal ReserveHarley Davidson Stores of AmericaHelzberg DiamondsHome DepotKay-Bee ToysKey 6.37.38.39.40.MarshallsParts CityPep BoysPetcoNations BankNeiman MarcusQuest CommunicationsRegions BankSaks IncorporatedSearsT MobileT.J. MaxTelstar CommunicationsThird World BankTiffany & CompanyToys R UsVerizonVISAWalgreensWal-MartSince it was introduced in 1989 Security Mesh isnow specified in virtually all federal, state and localGovernment buildings. This covers both officesand correction facilities. Security Mesh is specifiedby Homeland Security, the FBI, ATF, TreasuryDepartment and the Department of Defense.Security Mesh is everywhere. Look for it onplans, ask your drywall contractors to bid theAMICO Security Mesh System.Security Mesh and Secura Clips are sold as a systemFor pricing and availability on Security Mesh andSecura Clips contact:securitymesh@gibraltar1.comAMICO SECURA CLIPS ARE PATENTED IN THE UNITED STATES AND CANADA

Security Mesh Wall Penetration BarrierPART 1 GENERAL1.01 SCOPE OF WORKSupply and install steel expanded mesh panels as a penetrationbarrier behind wall board using the manufacturers’ recommendedmethod of installation.1.02 SYSTEM DESCRIPTIONAs manufactured by Alabama Metal Industries Corporation, (AMICO),Security Mesh shall be made from a sheet of steel that is simultaneouslyslit and stretched into a rigid and open continuous sheet that cannotunravel. The finished shape of the mesh openings shall be a flatteneddiamond. Conventional expanded metal not manufacturedspecifically for security purposes is NOT acceptable for thisuse. Security Mesh shall be attached to framing members by usingAMICO Secura Clips following the manufacturers recommendedspacing.1.03 REFERENCESAll components and parts in this specification shall meet or exceedcurrent standards and specifications as designated by the AmericanSociety for Testing and Materials and shall be certified SecurityMesh per ASTM F1267, Type 2, Class 1 mill finish.Underwriters Laboratories Fire Rated Assembles (per U/L subjectFile #1857) will not be jeopardized by using AMICO’s SecurityMesh in the fire rated assembly.1.04 SUBMITTALThe manufacturers’ submittal information shall include brochures,details and specifictions and samples if requested prior to ordering.Alabama Metal Industries CorporationJanuary 20121.05 STORAGE AND HANDLINGMaterials shall be stored in a clean dry location with proper ventilation to avoid damage from moisture. Materials shall be protectedagainst damage from weather, vandalism, and theft. In the event offreight damage, note freight bill and contact manufacturer immediately.PART 2 MATERIALS2.01 MANUFACTURERALABAMA METAL INDUSTRIES CORPORATION, (AMICO),3245 Fayette Avenue u Birmingham, AL 35208Telephone for sales 800/366-2642 Technical 205/783-6224 uFacsimile 205/786-6527 u www.amico-securityproducts.com2.02 MATERIALSA. AMICO SECURITY MESH – ASM .75 –9F MAXIMUM SECURITYThe Security Mesh used shall conform to the following specification:Carbon steel – meet or exceed ASTM A-10111. Width of panel – 4 ft. ( Also produced in 5ft. & 6ft. widths)2. Length of panel – 8 ft ( Also produced in 10ft & 12ft lengths)3. Mesh diamond width – 0.923 inch x 2.120 inch long bond tobond with13 diamonds per foot4. Mesh size opening – width 0.563 inch x 1.688 inch long allowing63% open area5. Mesh strand width – 0.164 inch6. Mesh strand thickness – 0.120 inch7. Weight – 1.71 pounds per square foot8. Security Mesh isproduced by Alabama Metal Industries Corporation,(AMICO).SECURITY MESH ASM .75-9FMaximum SecuritySecura Clips and the appropriate threaded fasteners. Welding isanacceptable means of attachment. Flat bugle head self-tappingscrews long enough to penetrate steel framing by at least 3/8-inch.For wood framing applications use 1-5/8-inch fine thread drywallscrew allowing the fastener to penetrate the framing member atleast 1-1/2 inches. Install Secura Clips, at a minimum, on 12-inchcenters per framing member. Secura Clips are the manufacturer’spreferred method of securing mesh panels to framing.C. FINISHSecurity Mesh is supplied “mill finish” HR P&O. No sealersor galvanizing is required for typical applications. In some veryunique situations stainless steel Security Mesh is supplied.For information concerning applications where stainlesssteel may be advantageous please call 800/366-2642 x 6224.PART 3 EXECUTION3.01 INSTALLATIONFraming members should be no less than 20GA. Security Meshpanels may be installed with diamonds running in either direction. Itis preferred to have mesh joints either join staggered as in detail “A”or butt together as in detail “B”. It is also acceptable to overlap meshjoints with owner’s prior written approval. Panels shall join on framingmembers. If panels butt in between framing members, in any direction,adjoining panels shall be tied with 18GA tie wire at the samefrequency as clips or welding.Tolerances: SWD -0 ¼” per foot of dimensionLWD -0 ¼” per foot of dimensionB. AMICO SECURA CLIPSSecurity Mesh shall be attached to framing members using AMICODetail “A” - Panels StaggeredDetail “B” - Panels Butt Joints

Security Mesh Wall Penetration BarrierPART 1 GENERAL1.01 SCOPE OF WORKSupply and install steel expanded mesh panels as a penetrationbarrier behind wall board using the manufacturers’ recommendedmethod of installation.1.02 SYSTEM DESCRIPTIONAs manufactured by Alabama Metal Industries Corporation, (AMICO),Security Mesh shall be made from a sheet of steel that is simultaneouslyslit and stretched into a rigid and open continuous sheet that cannotunravel. The finished shape of the mesh openings shall be a flatteneddiamond. Conventional expanded metal not manufacturedspecifically for security purposes is NOT acceptable for thisuse. Security Mesh shall be attached to framing members by usingAMICO Secura Clips following the manufacturers recommendedspacing.1.03 REFERENCESAll components and parts in this specification shall meet or exceedcurrent standards and specifications as designated by the AmericanSociety for Testing and Materials and shall be certified SecurityMesh per ASTM F1267, Type 2, Class 1 mill finish.Underwriters Laboratories Fire Rated Assembles (per U/L subjectFile #1857) will not be jeopardized by using AMICO’s SecurityMesh in the fire rated assembly.1.04 SUBMITTALThe manufacturers’ submittal information shall include brochures,details and specifictions and samples if requested prior to ordering.Alabama Metal Industries CorporationJanuary 20121.05 STORAGE AND HANDLINGMaterials shall be stored in a clean dry location with proper ventilation to avoid damage from moisture. Materials shall be protectedagainst damage from weather, vandalism, and theft. In the event offreight damage, note freight bill and contact manufacturer immediately.PART 2 MATERIALS2.01 MANUFACTURERALABAMA METAL INDUSTRIES CORPORATION, (AMICO),3245 Fayette Avenue u Birmingham, AL 35208Telephone for sales 800/366-2642 Technical 205/783-6224 uFacsimile 205/786-6527 u www.amico-securityproducts.com2.02 MATERIALA. AMICO SECURITY MESH – ASM .75-9F HEAVYThe Security Mesh used shall conform to the following specification:Carbon steel – meet or exceed ASTM A-10111. Width of panel – 4 ft. ( Also produced in 5ft. & 6ft. widths)2. Length of panel – 8 ft ( Also produced in 10ft & 12ft lengths)3. Mesh diamond width – 0.923 inch x 2.120 inch long bond tobond 13 with diamonds per lineal foot4. Mesh size opening – width 0.563” inch x 1.688” inch long allowing63 % open area5. Mesh strand width - 0.164 inch6. Mesh strand thickness – 0.140 inch7. Weight – 2.38 pounds per square foot8. Security Mesh is produced by Alabama Metal IndustriesCorporation, (AMICO).SECURITY MESH ASM .75-9F HEAVYSuper Maximum SecuritySecura Clips and the appropriate threaded fasteners. Welding isanacceptable means of attachment. Flat bugle head self-tappingscrews long enough to penetrate steel framing by at least 3/8-inch.For wood framing applications use 1-5/8-inch fine thread drywallscrew allowing the fastener to penetrate the framing member atleast 1-1/2 inches. Install Secura Clips, at a minimum, on 12-inchcenters per framing member. Secura Clips are the manufacturer’spreferred method of securing mesh panels to framing.C. FINISHSecurity Mesh is supplied “mill finish” HR P&O. No sealersor galvanizing is required for typical applications. In some veryunique situations stainless steel Security Mesh is supplied.For information concerning applications where stainlesssteel may be advantageous please call 800/366-2642 x 6224.PART 3 EXECUTION3.01 INSTALLATIONFraming members should be no less than 20GA. Security Meshpanels may be installed with diamonds running in either direction. Itis preferred to have mesh joints either join staggered as in detail “A”or butt together as in detail “B”. It is also acceptable to overlap meshjoints with owner’s prior written approval. Panels shall join on framingmembers. If panels butt in between framing members, in any direction,adjoining panels shall be tied with 18GA tie wire at the samefrequency as clips or welding.Tolerances: SWD -0 ¼” per foot of dimensionLWD -0 ¼” per foot of dimensionB. AMICO SECURA CLIPSSecurity Mesh shall be attached to framing members using AMICODetail “A” - Panels StaggeredDetail “B” - Panels Butt Joints

Security Mesh Wall Penetration BarrierPART 1 GENERAL1.01 SCOPE OF WORKSupply and install steel expanded mesh panels as a penetrationbarrier behind wall board using the manufacturers’ recommendedmethod of installation.1.02 SYSTEM DESCRIPTIONAs manufactured by Alabama Metal Industries Corporation, (AMICO),Security Mesh shall be made from a sheet of steel that is simultaneouslyslit and stretched into a rigid and open continuous sheet that cannotunravel. The finished shape of the mesh openings shall be a flatteneddiamond. Conventional expanded metal not manufacturedspecifically for security purposes is NOT acceptable for thisuse. Security Mesh shall be attached to framing members by usingAMICO Secura Clips following the manufacturers recommendedspacing.1.03 REFERENCESAll components and parts in this specification shall meet or exceedcurrent standards and specifications as designated by the AmericanSociety for Testing and Materials and shall be certified SecurityMesh per ASTM F1267, Type 2, Class 1 mill finish.Underwriters Laboratories Fire Rated Assembles (per U/L subjectFile #1857) will not be jeopardized by using AMICO’s SecurityMesh in the fire rated assembly.1.04 SUBMITTALThe manufacturers’ submittal information shall include brochures,details and specifictions and samples if requested prior to ordering.Alabama Metal Industries CorporationJanuary 20121.05 STORAGE AND HANDLINGMaterials shall be stored in a clean dry location with proper ventilation to avoid damage from moisture. Materials shall be protectedagainst damage from weather, vandalism, and theft. In the event offreight damage, note freight bill and contact manufacturer immediately.PART 2 MATERIALS2.01 MANUFACTURERALABAMA METAL INDUSTRIES CORPORATION, (AMICO),3245 Fayette Avenue u Birmingham, AL 35208Telephone for sales 800/366-2642 Technical 205/783-6224 uFacsimile 205/786-6527 u www.amico-securityproducts.com2.02 MATERIALSA. AMICO SECURITY MESH – ASM .50 – 13FThe Security Mesh used shall conform to the following specification:Carbon steel – meet or exceed ASTM A-10111. Width of panel – 4 ft. ( Also produced in 5ft. & 6ft. widths)2. Length of panel – 8 ft ( Also produced in 10ft & 12ft lengths)3. Mesh diamond width – 0.500 inch x 1.260 inch long bond tobond with 24 diamonds per lineal foot4. Mesh size opening – width 0.250 inch x 1.000 inch long allowing57% open area5. Mesh strand width - 0.122 inch6. Mesh strand thickness – 0.070 inch7. Weight – 1.40 pounds per square foot8. Security Mesh is produced by Alabama Metal IndustriesCorporation, (AMICO).SECURITY MESH ASM .50-13FMaximum SecuritySecura Clips and the appropriate threaded fasteners. Welding isanacceptable means of attachment. Flat bugle head self-tappingscrews long enough to penetrate steel framing by at least 3/8-inch.For wood framing applications use 1-5/8-inch fine thread drywallscrew allowing the fastener to penetrate the framing member atleast 1-1/2 inches. Install Secura Clips, at a minimum, on 12-inchcenters per framing member. Secura Clips are the manufacturer’spreferred method of securing mesh panels to framing.C. FINISHSecurity Mesh is supplied “mill finish” HR P&O. No sealersor galvanizing is required for typical applications. In some veryunique situations stainless steel Security Mesh is supplied.For information concerning applications where stainlesssteel may be advantageous please call 800/366-2642 x 6224.PART 3 EXECUTION3.01 INSTALLATIONFraming members should be no less than 20GA. Security Meshpanels may be installed with diamonds running in either direction. Itis preferred to have mesh joints either join staggered as in detail “A”or butt together as in detail “B”. It is also acceptable to overlap meshjoints with owner’s prior written approval. Panels shall join on framingmembers. If panels butt in between framing members, in any direction,adjoining panels shall be tied with 18GA tie wire at the samefrequency as clips or welding.Tolerances: SWD -0 ¼” per foot of dimensionLWD -0 ¼” per foot of dimensionB. AMICO SECURA CLIPSSecurity Mesh shall be attached to framing members using AMICODetail “A” - Panels StaggeredDetail “B” - Panels Butt Joints

Security Mesh Wall Penetration BarrierPART 1 GENERAL1.01 SCOPE OF WORKSupply and install steel expanded mesh panels as a penetrationbarrier behind wall board using the manufacturers’ recommendedmethod of installation.1.02 SYSTEM DESCRIPTIONAs manufactured by Alabama Metal Industries Corporation, (AMICO),Security Mesh shall be made from a sheet of steel that is simultaneouslyslit and stretched into a rigid and open continuous sheet that cannotunravel. The finished shape of the mesh openings shall be a flatteneddiamond. Conventional expanded metal not manufacturedspecifically for security purposes is NOT acceptable for thisuse. Security Mesh shall be attached to framing members by usingAMICO Secura Clips following the manufacturers recommendedspacing.1.03 REFERENCESAll components and parts in this specification shall meet or exceedcurrent standards and specifications as designated by the AmericanSociety for Testing and Materials and shall be certified SecurityMesh per ASTM F1267, Type 2, Class 1 mill finish.Underwriters Laboratories Fire Rated Assembles (per U/L subjectFile #1857) will not be jeopardized by using AMICO’s SecurityMesh in the fire rated assembly.1.04 SUBMITTALThe manufacturers’ submittal information shall include brochures,details and specifictions and samples if requested prior to ordering.Alabama Metal Industries CorporationJanuary 20121.05 STORAGE AND HANDLINGMaterials shall be stored in a clean dry location with proper ventilation to avoid damage from moisture. Materials shall be protectedagainst damage from weather, vandalism, and theft. In the event offreight damage, note freight bill and contact manufacturer immediately.PART 2 MATERIALS2.01 MANUFACTURERALABAMA METAL INDUSTRIES CORPORATION, (AMICO),3245 Fayette Avenue u Birmingham, AL 35208Telephone for sales 800/366-2642 Technical 205/783-6224 uFacsimile 205/786-6527 u www.amico-securityproducts.com2.02 MATERIALSA. AMICO SECURITY MESH – ASM 1.5-9FThe Security Mesh used shall conform to the following specification:Carbon steel – meet or exceed ASTM A-10111. Width of panel – 4 ft. ( Also produced in 5ft. & 6ft. widths)2. Length of panel – 8 ft ( Also produced in 12ft lengths)3. Mesh diamond width – 1.330 inch x 3.200 inch long bond tobond with 9 diamonds per lineal foot4. Mesh size opening – width 1.000 inch x 2.563 inch long allowing77% open area5. Mesh strand width - 0.175 inch6. Mesh strand thickness – 0.110 inch7. Weight – 1.11 pounds per square foot8. Security Mesh is produced by Alabama Metal IndustriesCorporation, (AMICO).SECURITY MESH ASM 1.5-9FMedium SecuritySecura Clips and the appropriate threaded fasteners. Welding isanacceptable means of attachment. Flat bugle head self-tappingscrews long enough to penetrate steel framing by at least 3/8-inch.For wood framing applications use 1-5/8-inch fine thread drywallscrew allowing the fastener to penetrate the framing member atleast 1-1/2 inches. Install Secura Clips, at a minimum, on 12-inchcenters per framing member. Secura Clips are the manufacturer’spreferred method of securing mesh panels to framing.C. FINISHSecurity Mesh is supplied “mill finish” HR P&O. No sealersor galvanizing is required for typical applications. In some veryunique situations stainless steel Security Mesh is supplied.For information concerning applications where stainlesssteel may be advantageous please call 800/366-2642 x 6224.PART 3 EXECUTION3.01 INSTALLATIONFraming members should be no less than 20GA. Security Meshpanels may be installed with diamonds running in either direction. Itis preferred to have mesh joints either join staggered as in detail “A”or butt together as in detail “B”. It is also acceptable to overlap meshjoints with owner’s prior written approval. Panels shall join on framingmembers. If panels butt in between framing members, in any direction,adjoining panels shall be tied with 18GA tie wire at the samefrequency as clips or welding.Tolerances: SWD -0 ¼” per foot of dimensionLWD -0 ¼” per foot of dimensionB. AMICO SECURA CLIPSSecurity Mesh shall be attached to framing members using AMICODetail “A” - Panels StaggeredDetail “B” - Panels Butt Joints

Security Mesh Wall Penetration BarrierPART 1 GENERAL1.01 SCOPE OF WORKSupply and install steel expanded mesh panels as a penetrationbarrier behind wall board using the manufacturers’ recommendedmethod of installation.1.02 SYSTEM DESCRIPTIONAs manufactured by Alabama Metal Industries Corporation, (AMICO),Security Mesh shall be made from a sheet of steel that is simultaneouslyslit and stretched into a rigid and open continuous sheet that cannotunravel. The finished shape of the mesh openings shall be a flatteneddiamond. Conventional expanded me

The AMICO System is used to secure people and property from unwanted intrusion. . Amsouth Bank 2. AT&T 3. Babies R Us 4. Bank of America 5. Bank One 6. Bank of Texas 7. . Regions Bank 29. Saks Incorporated 30. Sears 31. T Mobile 32. T.J. Max 33. Telstar Communications 34.