Transcription
RunCam Swift 2USER MANUAL
Connection* Unplug the 5D-OSD menu cable after OSD setting.Transmitter2 pin extension cord5-36VPower inGND5-36V inGNDUPLTo VBAT RDOWN5D-OSD menu cableVideo outAudio outVBAT
Dimensions & Installation28.5mm1 Nylon Gaskets2 M2*4 Screws3 M3*5 Screws4 M3 Non-slip Nuts26mm233226mm5-36V22114411
OSD MenuOSD Setting: Press and hold the UP button for 2 seconds to enter OSD setup menu.Customize the PILOT name: Use the UP,DOWN, LEFT and RIGHT buttons tonavigate through the letters andconfirm with the CENTER button.RunCam1234567890ABCDEFGHIJKLMNOPQRSTUVWXYZa b c d e f g h i j k l m n XITONONONOFF· PILOT: ON/OFF· TIMER: ON/OFF· VOLTAGE: ON/OFF· BASELINE: OFF/1-9· EXIT: Save the current settings and exitQuick settings:Long press the LEFT/DOWN/RIGHTbutton for 2 seconds to activate theVOLTAGE/PILOT/TIMER, then you can usethe UP, DOWN, LEFT and RIGHT buttonsto move it to the appropriate location onthe screen, and press the CENTER buttonto exit.The OSD displays by default the inputvoltageof the camera. If the VBAT cableis connected to the battery's positive side,it displays the battery voltage instead.
OSD Menu· Voltage Calibration· Press and hold the RIGHT button for 2seconds to select the voltage· Press and hold the CENTER button for 2seconds, the voltage starts to flash, nowyou can adjust the voltage:· Increase(LEFT button) or reduce(RIGHT button) 0.1V each press.Maximum adjustment range: 1v· After adjustment, press the CENTERbutton to select the voltage, then pressit again to save and exit.16.8vRunCam01:08
Camera Menu· EXPOSURE· MAIN MENUSETUPCAM TITLEEXPOSUREBACKLIGHTWHITE BALDAY & NIGHTIMAGE BRIGHTNESSAGCDWDRRETURNAUTO050OFFONRETENGLISH· CAM TITLE (ON/OFF)· LANGUAGE (English/中文)· WHITE BAL (ATW1 / ATW2 / AWC SET /MANUAL: MANUAL, INDOOR, OUTDOOR)· DPC (Cover the lens then press enter key)· SHUTTER (AUTO / 50-100000 / FLK)· BRIGHTNESS (50 / 0-255)· AGC (OFF / LOW / MIDDLE / HIGH)· DWDR (ON: 63 0-63 / OFF)
Camera Menu· IMAGE ADJIMAGE ADJLENS SHAD2DNRMIRRORFONT COLORCONTRASTSHARPNESSDISPLAYNEG IMAGERETURNUSER ADJ.OFFOFFOFFGAMMAPED LEVELCOLOR GAINRETURN110026USEROFF· LENS SHAD (OFF/ ON:22 0-255)· CONTRAST (110 / 0-255)· SHARPNESS (26 / 0-31)· DISPLAY (CRT/LCD/USER)· GAMMA (0.5 / 0.05-1.0)· PED LEVEL (17 / 0-63)· COLOR GAIN (176 / 0-255)0.50017176RET
Camera Menu· BACKLIGHT (BLC / HLC / OFF)BLCAREA SELAREA STATEGAINHEIGHTWIDTHLEFT/RIGHTTOP/BOTTOMRETURN· AREA SEL (AREA1/AREA2)· GAIN (042 / 0-255 )· HEIGHT (4 / 0-10)· WIDTH (3 / 0-9)· LEFT/RIGHT (6 / 0-6)· TOP/BOTTOM (10 / 0ALL DAYRET· LEVEL (200 / 0-255)· MODE (ALL DAY / NIGHT ONLY )
Camera Menu· DAY & NIGHT (AUTO / COLOR / B&W / EXT)D & N AUTOD N LEVELD N DELAYN D LEVELN D DELAYRETURN31D&N B&W080SEC032SECRET· DAYNIGHT LEVEL (80 / 0-176)· DAYNIGHT DELAY (3 / 1-30)DAY LEVEL (032 / 0-255)· NIGHTDAY DELAY (1 / 1-30)· NIGHTBURSTIR SMARTIR LEVELRETURN· BURST (OFF/ON)· IR SMART (OFF/ON)· IR LEVEL (HIGH/LOW)OFFOFFHIGHRET
ModelImage SensorHorizontal ResolutionLensSignal SystemIntegrated OSDIntegrated MICS/N RatioElectronic Shutter SpeedAuto Gain Control (AGC)Back Light Compensation (BLC)Min. IlluminationWDRDNRDay/NightPowerNet WeightDimensionsRunCam Swift 21/3″SONY SUPER HAD II CCD600TVL2.5mm (Default) / 2.3mm / 2.1mmPAL/NTSCYesYes 60dB (AGC OFF)PAL: 1/50 100,000; NTSC: 1/60 100,000YesYes0.01Lux@1.2FD-WDR2DNRColor/Auto/B&WDC 5-36V14g28.5mm*26mm*26mm
RunCam Swift 2 USER MANUAL. Connection UPUP DOWNDOWN L R Transmitter 5D-OSD menu cable 2 pin extension cord Power in GND To VBAT * Unplug the 5D-OSD menu cable after OSD setting. 5-36V in GND Video out Audio out VBAT 5-36V. 1 Nylon Gaskets 2 M2*4 Screws 3 M3*5 Screws 4 M3 Non-slip Nuts 26mm 28.5mm 26mm 1 1 4 4 1 1 2 2 2 3 3 2
